Stabilization of fluoroindate glasses by magnesium fluoride and other heavy metal fluorides

Their extended transparency in the IR makes them attractive for use as optical fibers for CO laser power delivery and optical amplification. This paper firstly describes the spectacular stabilizing effect of MgF2 on the binary system InF3-BaF2. The investigation of the InF3-BaF2-MgF2 system led to samples up to 5mm in thickness. Further optimization of this system was achieved by incorporation of limited amounts of other fluorides and resulted in increased resistence to devitrification. The second approach of this work was concerned to the investigation of the pseudo-ternary system InF3-GdF3-GaF3 at constant concentrations of ZnF2-SrF2-BaF2-NaF. Several compositions were studied in this system. The samples presented a better thermal stability when compared to other families of fluoride glasses. Therefore, these glasses seem to be very promising for the fabrication of special optical fibers. Thermal data are reported.

Use of the Optical Cantilever Microphone in Photoacoustic Spectroscopy

A novel cantilever pressure sensor was developed in the Department of Physics at the University of Turku in order to solve the sensitivity problems which are encountered when condenser microphones are used in photoacoustic spectroscopy. The cantilever pressure sensor, combined with a laser interferometer for the measurement of the cantilever movements, proved to be highly sensitive. The original aim of this work was to integrate the sensor in a photoacoustic gas detector working in a differential measurement scheme. The integration was made successfully into three prototypes. In addition, the cantilever was also integrated in the photoacoustic FTIR measurement schemes of gas-, liquid-, and solid-phase samples. A theoretical model for the signal generation in each measurement scheme was created and the optimal celldesign discussed. The sensitivity and selectivity of the differential method were evaluated when a blackbody radiator and a mechanical chopper were used with CO₂, CH4, CO, and C2H4 gases. The detection limits were in the sub-ppm level for all four gases with only a 1.3 second integration time and the cross interference was well below one percent for all gas combinations other than those between hydrocarbons. Sensitivity with other infrared sources was compared using ethylene as an example gas. In the comparison of sensitivity with different infrared sources the electrically modulated blackbody radiator gave a 35 times higher and the CO2-laser a 100 times lower detection limit than the blackbody radiator with a mechanical chopper. As a conclusion, the differential system is well suited to rapid single gas measurements. Gas-phase photoacoustic FTIR spectroscopy gives the best performance, when several components have to be analyzed simultaneously from multicomponent samples. Multicomponent measurements were demonstrated with a sample that contained different concentrations of CO₂, H₂O, CO, and four different hydrocarbons. It required an approximately 10 times longer measurement time to achieve the same detection limit for a single gas as with the differential system. The properties of the photoacoustic FTIR spectroscopy were also compared to conventional transmission FTIR spectroscopy by simulations. Solid- and liquid-phase photoacoustic FTIR spectroscopy has several advantages compared to other techniques and therefore it also has a great variety of applications. A comparison of the signal-to-noise ratio between photoacoustic cells with a cantilever microphone and a condenser microphone was done with standard carbon black, polyethene, and sunflower oil samples. The cell with the cantilever microphone proved to have a 5-10 times higher signal-to-noise ratio than the reference detector, depending on the sample. Cantilever enhanced photoacoustics will be an effective tool for gas detection and analysis of solid- and liquid-phase samples. The preliminary prototypes gave good results in all three measurement schemes that were studied. According to simulations, there are possibilities for further enhancement of the sensitivity, as well as other properties, of each system.

Use of the EPR technique to determine thermal stability of some humified organic substances found in soil organic-mineral fractions

In this work, using the EPR spectroscopy, we analysed the thermal stability of some organic-mineral compounds found in a Gleysoil from Rio Janeiro. It was observed a complete disappearance of the EPR signal around 600 °C for the < 2 µm fraction and a residual EPR signal of semiquinone free radical for the 2-20 µm and 20-53 µm fractions at the same temperature. Also, the experiments showed that the 2-20 µm fraction had a larger concentration of semiquinone free radical per g of carbon and a smaller line width indicated a larger humification of this fraction. This is an evidence that the soil organic matter of this fraction (2-20 µm) is more stable than the other ones.

Osteoclastic tartrate-resistant acid phosphatase 5b. Diagnostic use and biological significance in bone physiology

The skeleton undergoes continuous turnover throughout life. In women, an increase in bone turnover is pronounced during childhood and puberty and after menopause. Bone turnover can be monitored by measuring biochemical markers of bone resorption and bone formation. Tartrate-resistant acid phosphatase (TRACP) is an enzyme secreted by osteoclasts, macrophages and dendritic cells. The secreted enzyme can be detected from the blood circulation by recently developed immunoassays. In blood circulation, the enzyme exists as two isoforms, TRACP 5a with an intact polypeptide chain and TRACP 5b in which the polypeptide chain consists of two subunits. The 5b form is predominantly secreted by osteoclasts and is thus associated with bone turnover. The secretion of TRACP 5b is not directly related to bone resorption; instead, the levels are shown to be proportional to the number of osteoclasts. Therefore, the combination of TRACP 5b and a marker reflecting bone degradation, such as C-terminal cross-linked telopeptides of type I collagen (CTX), enables a more profound analysis of the changes in bone turnover. In this study, recombinant TRACP 5a-like protein was proteolytically processed into TRACP 5b-like two subunit form. The 5b-like form was more active both as an acid phosphatase and in producing reactive oxygen species, suggesting a possible function for TRACP 5b in osteoclastic bone resorption. Even though both TRACP 5a and 5b were detected in osteoclasts, serum TRACP 5a levels demonstrated no change in response to alendronate treatment of postmenopausal women. However, TRACP 5b levels decreased substantially, demonstrating that alendronate decreases the number of osteoclasts. This was confirmed in human osteoclast cultures, showing that alendronate decreased the number of osteoclats by inducing osteoclast apoptosis, and TRACP 5b was not secreted as an active enzyme from the apoptotic osteoclasts. In peripubertal girls, the highest levels of TRACP 5b and other bone turnover markers were observed at the time of menarche, whereas at the same time the ratio of CTX to TRACP 5b was lowest, indicating the presence of a high number of osteoclasts with decreased resorptive activity. These results support the earlier findings that TRACP 5b is the predominant form of TRACP secreted by osteoclasts. The major source of circulating TRACP 5a remains to be established, but is most likely other cells of the macrophage-monocyte system. The results also suggest that bone turnover can be differentially affected by both osteoclast number and their resorptive activity, and provide further support for the possible clinical use of TRACP 5b as a marker of osteoclast number.

Position sensorless electrically excited synchronous motor drive for industrial use based on direct flux linkage and torque control

Synchronous machines with an AC converter are used mainly in large drives, for example in ship propulsion drives as well as in rolling mill drives in steel industry. These motors are used because of their high efficiency, high overload capacity and good performance in the field weakening area. Present day drives for electrically excited synchronous motors are equipped with position sensors. Most drives for electrically excited synchronous motors will be equipped with position sensors also in future. This kind of drives with good dynamics are mainly used in metal industry. Drives without a position sensor can be used e.g. in ship propulsion and in large pump and blower drives. Nowadays, these drives are equipped with a position sensor, too. The tendency is to avoid a position sensor if possible, since a sensor reduces the reliability of the drive and increases costs (latter is not very significant for large drives). A new control technique for a synchronous motor drive is a combination of the Direct Flux Linkage Control (DFLC) based on a voltage model and a supervising method (e.g. current model). This combination is called Direct Torque Control method (DTC). In the case of the position sensorless drive, the DTC can be implemented by using other supervising methods that keep the stator flux linkage origin centered. In this thesis, a method for the observation of the drift of the real stator flux linkage in the DTC drive is introduced. It is also shown how this method can be used as a supervising method that keeps the stator flux linkage origin centered in the case of the DTC. In the position sensorless case, a synchronous motor can be started up with the DTC control, when a method for the determination of the initial rotor position presented in this thesis is used. The load characteristics of such a drive are not very good at low rotational speeds. Furthermore, continuous operation at a zero speed and at a low rotational speed is not possible, which is partly due to the problems related to the flux linkage estimate. For operation in a low speed area, a stator current control method based on the DFLC modulator (DMCQ is presented. With the DMCC, it is possible to start up and operate a synchronous motor at a zero speed and at low rotational speeds in general. The DMCC is necessary in situations where high torque (e.g. nominal torque) is required at the starting moment, or if the motor runs several seconds at a zero speed or at a low speed range (up to 2 Hz). The behaviour of the described methods is shown with test results. The test results are presented for the direct flux linkage and torque controlled test drive system with a 14.5 kVA, four pole salient pole synchronous motor with a damper winding and electric excitation. The static accuracy of the drive is verified by measuring the torque in a static load operation, and the dynamics of the drive is proven in load transient tests. The performance of the drive concept presented in this work is sufficient e.g. for ship propulsion and for large pump drives. Furthermore, the developed methods are almost independent of the machine parameters.

Minimization of the experimental workload for the prediction of pollutants propagation in rivers. Mathematical modelling and knowledge re-use

The present thesis in focused on the minimization of experimental efforts for the prediction of pollutant propagation in rivers by mathematical modelling and knowledge re-use. Mathematical modelling is based on the well known advection-dispersion equation, while the knowledge re-use approach employs the methods of case based reasoning, graphical analysis and text mining. The thesis contribution to the pollutant transport research field consists of: (1) analytical and numerical models for pollutant transport prediction; (2) two novel techniques which enable the use of variable parameters along rivers in analytical models; (3) models for the estimation of pollutant transport characteristic parameters (velocity, dispersion coefficient and nutrient transformation rates) as functions of water flow, channel characteristics and/or seasonality; (4) the graphical analysis method to be used for the identification of pollution sources along rivers; (5) a case based reasoning tool for the identification of crucial information related to the pollutant transport modelling; (6) and the application of a software tool for the reuse of information during pollutants transport modelling research. These support tools are applicable in the water quality research field and in practice as well, as they can be involved in multiple activities. The models are capable of predicting pollutant propagation along rivers in case of both ordinary pollution and accidents. They can also be applied for other similar rivers in modelling of pollutant transport in rivers with low availability of experimental data concerning concentration. This is because models for parameter estimation developed in the present thesis enable the calculation of transport characteristic parameters as functions of river hydraulic parameters and/or seasonality. The similarity between rivers is assessed using case based reasoning tools, and additional necessary information can be identified by using the software for the information reuse. Such systems represent support for users and open up possibilities for new modelling methods, monitoring facilities and for better river water quality management tools. They are useful also for the estimation of environmental impact of possible technological changes and can be applied in the pre-design stage or/and in the practical use of processes as well.

Lämpöpumppujen vaikutukset sähköverkkoliiketoiminnan kannalta

Energiatehokkuus sekä ilmastonmuutos ovat aiheuttaneet pyrkimyksen vähentää kokonaisenergiankulutuksia erilaisissa rakennuksissa. Lämmitysjärjestelmissä tämä on näkynyt voimakkaana lämpöpumppumäärien kasvuna. Lämpöpumput vaikuttavat erilaisissa rakennus- ja lämmitystyypeissä myös sähköenergiankulutukseen. Lämpöpumppujen käytöstä saadaan eniten hyötyä lämmityskustannuksiin sähkölämmitteisissä rakennuksissa. Seurauksena on, että tällaisen rakennuksen sähkönkulutus ja siten myös sähkölasku pienenevät. Toisaalta muihin kuin sähkölämmitteisiin rakennuksiin asennettu lämpöpumppu kasvattaa sähköenergiankulutusta. Lämpöpumppuihin integroitu jäähdytysominaisuus myös tavallisesti lisää sähkönkulutusta. Tämän tutkimuksen tarkoituksena on selvittää, kuinka lämpöpumput vaikuttavat sähköenergiankulutukseen. Vaikutuksia tutkitaan sähköverkkoyhtiöiden kannalta sähköenergian ja liikevaihdon osalta. Tarkastelussa käytetään neljää yleisintä lämpöpumpputyyppiä, ja niiden toimintaa verrataan eri rakennustyyppien lämmitysjärjestelmiin. Työssä käsitellään lämpöpumppujen toimintaa ja käytettävyyttä muiden lämmitysmenetelmien korvaajina tai lisänä. Tämän kirjallisen työn lisäksi on tehty laskentaohjelma, joka on perusteena työssä esitetyille tuloksille. Sen tarkoituksena on selvittää lämpöpumppujen vaikutukset sähköverkkoliiketoimintaan energiayhtiöissä. Vaikutukset yksittäiseen energiayhtiöön ovat eniten riippuvaisia lämpöpumppujen asennuskohteista, lämpöpumppujen toiminnasta ja lämpöpumpputyypistä. Kuluttajat tulevat määräämään vaikutusten suuruuden, koska lämpöpumppujen lukumäärällä ja käytöllä on sähköenergiankulutukseen huomattava merkitys. Vaikutus sähköenergiaan energiayhtiöiden kannalta voi yleisesti ottaen olla 2020-luvulle mentäessä merkittävä. Tutkittavassa verkkoyhtiössä vaikutuksen sähköenergiaan arvioidaan olevan 10 % luokkaa yhdeltä vuodelta verrattuna tämän päivän kokonaissähköenergiankulutukseen. Vaikutus verkkoliikevaihtoon on arviolta puolet pienempi. Tällaiset tulokset edellyttävät lämpöpumppumäärän moninkertaistumista nykyisestä, mikä on myös odotettavissa.

Use of sorghum straw (Sorghum bicolor) for second generation ethanol production: pretreatment and enzymatic hydrolysis

Agronomic biomass yields of forage sorghum BRS 655 presented similar results to other energy crops, producing 9 to 12.6 tons/ha (dry mass) of sorghum straw. The objective of this study was to evaluate the lignocellulosic part of this cultivar in terms of its potential in the different unit processes in the production of cellulosic ethanol, measuring the effects of pretreatment and enzymatic hydrolysis. Three types of pre-treatments for two reaction times were conducted to evaluate the characteristics of the pulp for subsequent saccharification. The pulp pretreated by alkali, and by acid followed by delignification, attained hydrolysis rates of over 90%.

Energiatehokas toimisto - LED -teknologia

Tässä työssä käsitellään toimistorakennusten energiankulutusta ja nykyisiä toimistojen valaistusratkaisuja. Työssä perehdytään LED-valaistusteknologiaan sekä energiatehokkaaseen toimistovalaistukseen. Energiatehokkaan valaistuksen osalta käsitellään toimistovalaistuksen vaatimuksia, valaistuksen ohjausta ja luonnonvalon vaikutusta energiankulutukseen. Tutkimuskohteena oli Helsingin yliopiston tiloissa sijaitsevat neljä toimistohuonetta, joista kahden valaistusjärjestelmä uusittiin ja kahden jätettiin entiselleen vertailun vuoksi. Tutkimuksessa kartoitettiin toimistohuoneiden nykyistä energiankulutusta ja etsittiin keinoja sen tehostamiseen valaistuksen osalta. Tässä työssä tutkittiin erityisesti LED-valaisimien ja valaistuksen ohjauksen hyödynnettävyyttä toimistotiloissa. Toimistotilojen elinkaarikustannuslaskelmilla pyrittiin toteamaan valaistusjärjestelmien taloudellinen kannattavuus 30 vuoden tarkastelujaksolla. Tutkimuksessa tehtiin käyttäjäkysely toimistohuoneissa työskenteleville henkilöille ennen ja jälkeen muutoksen. Kyselyn perusteella voitiin todeta uusitun valaistusjärjestelmän hyödyt ja puutteet käyttäjän näkökulmasta.

Sensitive Troponin Assays: Diagnostic and Prognostic Use in Cardiology

Cardiac troponins (cTns) are the recommended biochemical markers in the diagnosis of myocardial infarction (MI). They are very sensitive and tissue-specific but are limited by their delayed appearance in the circulation. Biochemical markers with more rapid release kinetics, e.g. myoglobin and especially heart-type fatty acid-binding protein (H-FABP), have been used to enhance the early identification of MI. The implementation of cTns into clinical practice has shown that cardiomyocyte injury occurs in many other clinical conditions than MI. The aim of this study was to evaluate the impact of modern and highly sensitive cTnI assays on the early diagnosis of MI. In a patient cohort with suspected MI, such a sensitive cTnI assay enhanced the early diagnostic accuracy when compared to a less sensitive cTnI assay and to myoglobin. When compared to H-FABP during the early hours after symptom onset, the sensitive cTnI assay showed at least similar and, after 6 hours, superior diagnostic accuracy. A positive cTnI test result had superior prognostic value when compared to H-FABP, even among early presenters. The prognostic value of cTn in acute heart failure (AHF) was evaluated in 364 patients who participated in the FINN-AKVA study. The patients presented with AHF but no acute coronary syndrome (ACS). Up to half of the patients had elevated cTn levels which were associated with higher 6-month mortality. The magnitude of cTn elevation was directly proportional to mortality. Finally, the clinical spectrum of cTnI elevations was evaluated in 991 cTnI positive emergency department (ED) patients. 83% of the patients had MI and 17% had cTnI elevation due to other clinical conditions. The latter patient group was characterized by lower absolute cTnI levels and – importantly – higher in-hospital mortality when compared to the MI patients. In conclusion, the use of a highly sensitive cTnI assay enhances the early diagnostic accuracy and risk stratification in suspected MI patients. Cardiac troponin elevations are highly prevalent also in other acute clinical conditions and indicate an adverse outcome of these patients.

Asbestin tunnistaminen keinonenällä

Asbesti on yleisnimike kuitumaisille silikaattimineraaleille. Sillä on monia hyviä ominaisuuksia. Siksi sitä on käytetty useisiin eri käyttötarkoituksiin jo yli 4 000 vuoden ajan. Sisäänhengitettynä asbesti aiheuttaa kuitenkin vakavia terveyshaittoja, mm. asbestoosia, keuhkosyöpää ja mesotelioomaa. Vuosina 1918-1988 Suomessa käytettiin asbestia 300 000 tonnia. Yleisintä käyttö oli 1960-70-lukujen vaihteessa. Sairauksien viive altistumisesta on 10-40 vuotta. Sairauksien esiintyminen onkin nyt suurimmillaan. Suurin osa sairauksista on hyvänlaatuisia keuhkopussin paksuuntumia eli plakkeja. Vuosittain asbestin aiheuttamiin sairauksiin, etupäässä syöpiin, kuolee Suomessa noin 100 ihmistä. Yhteensä altistuneita arvellaan olevan 250 000. Heistä elossa on noin 50 000. Vaarallisuutensa vuoksi asbestin käyttö on useissa maissa kielletty, mutta maailmalla sitä käytetään edelleen suuria määriä. Suomessa asbestin käyttöä rajoitettiin jo 1970-luvulla. Pieniä poikkeuksia lukuun ottamatta täyskielto tuli voimaan 1.1.1994. Suomessa asbestia esiintyy edelleen vanhoissa rakennuksissa. Asbestipurkutyö on luvanvaraista. Asbestitöissä on huolehdittava siitä, että kukaan ei altistu asbestille. Asbestipitoisen materiaalin tunnistaminen silmämääräisesti on vaikeaa. Materiaali luokitellaan asbestipitoiseksi, jos siinä on asbestia yli 1 painoprosenttia tai jos sitä voidaan pölyävyytensä takia pitää vaarallisena. Asbestipitoisen materiaalin kartoituksessa voidaan käyttää rakennussuunnitelmia, vanhoja asiakirjoja kuten urakoitsijan laskuja sekä tuntemusta rakennusajan yleisistä rakennustavoista. Varmuus saadaan kuitenkin vain tutkimalla materiaali esimerkiksi laboratoriokokeissa. Tässä diplomityössä on pyritty selvittämään, voidaanko asbesti tunnistaa ChemPro 100 -keinonenällä. Laite perustuu ioniliikkuvuusspektrometriaan eli eri yhdisteiden erilaiseen liikkuvuuteen kaasumaisessa väliaineessa. Menetelmä on nopea ja yksinkertainen. Tutkimusta varten hankittiin asbestipitoisia materiaaleja, joista saatuja tuloksia vertailtiin toisiinsa. Nykyiset asbestintunnistusmenetelmät ovat monimutkaisia ja hitaita. Jos keinonenä pystyttäisiin kouluttamaan tunnistamaan asbestimateriaali, helpottaisi se asbestikartoituksen tekemistä.

Very preterm infants in Finland - Use of health care services and economic consequences during the first five years of life

The aim of this thesis was to study the health, the hospitalisations, and the use of communal health care services in very preterm children during the first five years of life. In addition, the effect of very preterm birth and prematurity-related morbidities on the costs of hospitalisations, other health care services and the cost per quality adjusted life years (QALY) were studied. This population-based study included all very preterm children (gestational age (GA) <32 weeks or birth weight<1501g, N=2 064) and full-term controls (GA 37+0−41+6, N=200 609) born in Finland during 2000-2003. The data sources included national register data, costing data from the participating hospitals and parental questionnaires. This study showed that most very preterm infants born in Finland survived without prematurity-related morbidities diagnosed during the first years of life. They required relatively little hospital care after the initial discharge, which accounted for the vast majority of the total four-year hospitalisation costs. However, a minority of children born very preterm later developing morbidities had a long initial length of stay and more re-admissions and outpatient visits during the five-year follow-up period. In particular, the number and costs of non-emergency outpatient visits were considerable in individuals with prematurity-related morbidities. The need and costs of hospitalisations decreased clearly with each follow-up year, even in individuals with morbidities. The health-care related costs during the fifth year of life in children born very preterm without prematurity-related morbidities were close to the costs in infants born healthy at term. The cost per QALY of 19,245 € was at an acceptable level already by four years of age in the very preterm population as a whole. Prematurity-related later morbidities and decreasing GA increased the costs per QALY. As the initial hospital stay accounted for a great majority of the total four-year costs, and the costs of hospitalisation decreased with each follow-up year, the cost per QALY is likely to decrease with age. In conclusion, the majority of costs arising after the initial hospitalisation were associated with morbidities related to prematurity. Therefore offering high-quality neonatal care to prevent later morbidities in very preterm survivors has a long-term impact on the cost per QALY. In addition, this study indicates that when estimating the costs of prematurity after the first year of life, one should calculate not only the hospitalisation costs, but also other costs for social welfare services, primary care, and therapies, as these exceed the hospitalisation costs in very preterm infants during the fifth year of life.

Use of a Ca-selective electrode in the determination of total Ca in the production of crude sugar. Preliminary studies

The determination of the total calcium in juice, syrups, and other products of the sugar industry is investigated. Total calcium and free calcium is determinated by AAS and employing Ca-selective electrode respectively. A coefficient is obtained for the relation of total calcium with respect to free calcium. The coefficient is employed to determine the content of total calcium in accordance with the following equation.

Use Of Systems Approach with Total Quality Management in Industrial Organizations

The objective of the work has been to study why systems thinking should be used in combination with TQM, what are the main benefits of the integration and how it could best be done. The work analyzes the development of systems thinking and TQM with time and the main differences between them. The work defines prerequisites for adopting a systems approach and the organizational factors which embody the development of an efficient learning organization. The work proposes a model based on combination of an interactive management model and redesign to be used for application of systems approach with TQM in practice. The results of the work indicate that there are clear differences between systems thinking and TQM which justify their combination. Systems approach provides an additional complementary perspective to quality management. TQM is focused on optimizing operations at the operational level while interactive management and redesign of organization are focused on optimization operations at the conceptual level providing a holistic system for value generation. The empirical study demonstrates the applicability of the proposed model in one case study company but its application is tenable and possible also beyond this particular company. System dynamic modeling and other systems based techniques like cognitive mapping are useful methods for increasing understanding and learning about the behavior of systems. The empirical study emphasizes the importance of using a proper early warning system.

The Use of Radiostereometric Analysis in Fractures of the Distal Radius: From Phantom Models to Clinical Application

Radiostereometric analysis (RSA) is a highly accurate method for the measurement of in vivo micromotion of orthopaedic implants. Validation of the RSA method is a prerequisite for performing clinical RSA studies. Only a limited number of studies have utilised the RSA method in the evaluation of migration and inducible micromotion during fracture healing. Volar plate fixation of distal radial fractures has increased in popularity. There is still very little prospective randomised evidence supporting the use of these implants over other treatments. The aim of this study was to investigate the precision, accuracy, and feasibility of using RSA in the evaluation of healing in distal radius fractures treated with a volar fixed-angle plate. A physical phantom model was used to validate the RSA method for simple distal radius fractures. A computer simulation model was then used to validate the RSA method for more complex interfragmentary motion in intra-articular fractures. A separate pre-clinical investigation was performed in order to evaluate the possibility of using novel resorbable markers for RSA. Based on the validation studies, a prospective RSA cohort study of fifteen patients with plated AO type-C distal radius fractures with a 1-year follow-up was performed. RSA was shown to be highly accurate and precise in the measurement of fracture micromotion using both physical and computer simulated models of distal radius fractures. Resorbable RSA markers demonstrated potential for use in RSA. The RSA method was found to have a high clinical precision. The fractures underwent significant translational and rotational migration during the first two weeks after surgery, but not thereafter. Maximal grip caused significant translational and rotational interfragmentary micromotion. This inducible micromotion was detectable up to eighteen weeks, even after the achievement of radiographic union. The application of RSA in the measurement of fracture fragment migration and inducible interfragmentary micromotion in AO type-C distal radius fractures is feasible but technically demanding. RSA may be a unique tool in defining the progress of fracture union.