Atomic Layer Deposition of Electroluminescent ZnS, SrS, and BaS Thin Films

The light emitted by flat panel displays (FPD) can be generated in many different ways, such as for example alternating current thin film electroluminescence (ACTFEL), liquid crystal display (LCD), light emitting diode (LED), or plasma display panel (PDP) technologies. In this work, the focus was on ACTFEL devices and the goal was to develop new thin film processes for light emitting materials in ACTFEL devices. The films were deposited with the atomic layer deposition (ALD) method, which has been utilized in the manufacturing of ACTFEL displays since the mid-1980s. The ALD method is based on surface-controlled self-terminated reactions and a maximum of one layer of the desired material can be prepared during one deposition cycle. Therefore, the film thickness can be controlled simply by adjusting the number of deposition cycles. In addition, both large areas and deep trench structures can be covered uniformly. During this work, new ALD processes were developed for the following thin film materials: BaS, CuxS, MnS, PbS, SrS, SrSe, SrTe, SrS1-xSex, ZnS, and ZnS1-xSex. In addition, several ACTFEL devices were prepared where the light emitting material was BaS, SrS, SrS1-xSex, ZnS, or ZnS1-xSex thin film that was doped with Ce, Cu, Eu, Mn, or Pb. The sulfoselenide films were made by substituting the elemental selenium for sulfur on the substrate surface during film deposition. In this way, it was possible to replace a maximum of 90% of the sulfur with selenium, and the XRD analyses indicated that the films were solid solutions. The polycrystalline BaS, SrS, and ZnS thin films were deposited at 180-400, 120-460, and 280-500 °C, respectively, and the processes had a wide temperature range where the growth rate of the films was independent of the deposition temperature. The electroluminescence studies showed that the doped sulfoselenide films resulted in low emission intensity. However, the emission intensities and emission colors of the doped SrS, BaS, and ZnS films were comparable with those found in earlier studies. It was also shown that the electro-optical properties of the different ZnS:Mn devices were different as a consequence of different ZnS:Mn processes. Finally, it was concluded that because the higher deposition temperature seemed to result in a higher emission intensity, the thermal stability of the reactants has a significant role when the light emitting materials of ACTFEL devices are deposited with the ALD method.

Layer-by-layer self-assembly of modified hyaluronic acid/chitosan based on hydrogen bonding

The fabrication of hydrogen bonded polymer self-assembly for drug delivery has been accomplished via layer-by-layer sequential assembly from aqueous solution. In this study, the self-assembly was constructed based on hydrogen bonding between DNA base (adenine and thymine) pairs substituted on the backbone of chitosan and hyaluronic acid. Chitosan was modified with adenine, whereas hyaluronic acid was modified with thymine. Subsequently, these two polymers were sequentially absorbed on flat substrate by taking advantage of interactions of DNA base pairs via hydrogen bonding. Interlayer hydrogen bonding of these two polymers produces stable multilayer film without using any cross-linking agent. Thin film formation on quartz substrate has been monitored with UV-vis spectra and an AFM study. Formation of multilayer hydrogen-bonded thin film has been further confirmed with SEM. Encapsulation and release behavior of the therapeutic drug from the multilayer thin film at different conditions has been illustrated using UV-vis spectra. Cell viability of modified polymers using MTT assay confirmed no cytotoxic effect.

On probability-based inference under data missing by design

Whether a statistician wants to complement a probability model for observed data with a prior distribution and carry out fully probabilistic inference, or base the inference only on the likelihood function, may be a fundamental question in theory, but in practice it may well be of less importance if the likelihood contains much more information than the prior. Maximum likelihood inference can be justified as a Gaussian approximation at the posterior mode, using flat priors. However, in situations where parametric assumptions in standard statistical models would be too rigid, more flexible model formulation, combined with fully probabilistic inference, can be achieved using hierarchical Bayesian parametrization. This work includes five articles, all of which apply probability modeling under various problems involving incomplete observation. Three of the papers apply maximum likelihood estimation and two of them hierarchical Bayesian modeling. Because maximum likelihood may be presented as a special case of Bayesian inference, but not the other way round, in the introductory part of this work we present a framework for probability-based inference using only Bayesian concepts. We also re-derive some results presented in the original articles using the toolbox equipped herein, to show that they are also justifiable under this more general framework. Here the assumption of exchangeability and de Finetti's representation theorem are applied repeatedly for justifying the use of standard parametric probability models with conditionally independent likelihood contributions. It is argued that this same reasoning can be applied also under sampling from a finite population. The main emphasis here is in probability-based inference under incomplete observation due to study design. This is illustrated using a generic two-phase cohort sampling design as an example. The alternative approaches presented for analysis of such a design are full likelihood, which utilizes all observed information, and conditional likelihood, which is restricted to a completely observed set, conditioning on the rule that generated that set. Conditional likelihood inference is also applied for a joint analysis of prevalence and incidence data, a situation subject to both left censoring and left truncation. Other topics covered are model uncertainty and causal inference using posterior predictive distributions. We formulate a non-parametric monotonic regression model for one or more covariates and a Bayesian estimation procedure, and apply the model in the context of optimal sequential treatment regimes, demonstrating that inference based on posterior predictive distributions is feasible also in this case.

Drag reduction by a forward facing aerospike for a large angle blunt cone in high enthalpy flows

Drag reduction studies are conducted using a flat disc tipped aerospike for a 120-degree apex angle blunt cone model in high enthalpy flows. Accelerometer based force balance is used for the drag force measurement in the newly established free piston driven shock tunnel, HST3. Drag reduction upto about 58 percent has been achieved for Mach 8 flow of 5 MJ/kg specific enthalpy at zero degree angle of attack.

Investigations of separated flow over backward facing steps in IISc hypersonic shock tunnel

Two backward facing step (2 mm and 3 mm step height) models are selected for surface heat transfer measurements. The platinum thin film gauges are deposited on the Macor inserts using both hand paint and vacuum sputtering technique. Using the Eckert reference temperature method the heating rates has been theoretically calculated along the flat plate portion of the model and the theoretical estimates are compared with experimentally determined surface heat transfer rate. Theoretical analysis of heat flux distribution down stream of the backward facing step model has been carried out using Gai’s non-dimensional analysis. Based on the measured surface heating rates on the backward facing step, the reattachment distance is estimated for 2 and 3 mm step height at nominal Mach number of 7.6. It has been found from the present study that for 2 and 3 mm step height, it approximately takes about 10 and 8 step heights downstream of the model respectively for the flow to re-attach.

Dual Drug Delivery Microcapsules via Layer-by-Layer Self-Assembly

The integration of hydrophobic and hydrophilic drugs in the polymer microcapsule offers the possibility of developing a new drug delivery system that combines the best features of these two distinct classes of material. Recently, we have reported the encapsulation of an uncharged water-insoluble drug in the polymer membrane. The hydrophobic drug is deposited using a layer-by-layer (LbL) technique, which is based on the sequential adsorption of oppositely charged polyelectrolytes onto a charged substrate. In this paper, we report the encapsulation of two different drugs, which are invariably different in structure and in their solubility in water. We have characterized these dual drug vehicular capsules by confocal laser scanning microscopy, atomic force microscopy, visible microscopy, and transmission electron microscopy. The growth of a thin film on a flat substrate by LbL was monitored by UV−vis spectra. The desorption kinetics of two drugs from the thin film was modeled by a second-order rate model.

Strong gravity and the Yukawa field

A study of strong gravity field coupled to the Yukawa field is carried out for a conformally flat space-time. A quantitative relation between the strong interaction coupling constantg 2/hstrokc and the strong gravity constants (Lambda f~1028 cm–2,G f ~6.6×1030 C.G.S. units) is obtained givingg 2/hstroksim17, which is of the right order of magnitude. This justifies the contention that strong gravity is relevant for elementary particles (e.g., hadrons).

Axisymmetric deformation of a short magneto-strictive current-carrying cylinder

The title-problem has been reduced to that of solving a Fredholm integral equation of the second kind. One end of the cylinder is assumed to be fixed, while the cylinder is deformed by an axial current. The vertical displacement on the upper flat end of the cylinder has been determined from an iterative solution of the Fredholm equation valid for large values of the length. The radial displacement of the curved boundary has also been determined at the middle of the cylinder, by using the iterative solution.

Queensland Spanner Crab Fishery : Commercial quota setting for June 2015 – May 2016

The Australian fishery for spanner crabs is the largest in the world, with the larger Queensland (QLD) sector’s landings primarily exported live overseas and GVP valued ~A$5 million per year. Spanner crabs are unique in that they may live up to 15 years, significantly more than blue swimmer crabs (Portunus armatus) and mud crabs (Scylla serrata), the two other important crab species caught in Queensland. Spanner crabs are caught using a flat net called a dilly, on which the crabs becoming entangled via the swimming legs. Quota setting rules are used to assess and adjust total allowable harvest (quota) around an agreed target harvest of 1631 t and capped at a maximum of 2000 t. The quota varies based on catch rate indicators from the commercial fishery and a fishery-independent survey from the previous two years, compared to target reference points. Quota management applies only to ‘Managed Area A’ which includes waters between Rockhampton and the New South Wales (NSW) border. This report has been prepared to inform Fisheries Queensland (Department of Agriculture and Fisheries) and stakeholders of catch trends and the estimated quota of spanner crabs in Managed Area A for the forthcoming quota period (1 June 2015–31 May 2016). The quota calculations followed the methodology developed by the crab fishery Scientific Advisory Group (SAG) between November 2007 and March 2008. The total reported spanner crab harvest was 917 t for the 2014 calendar year, almost all of which was taken from Managed Area A. In 2014, a total of 59 vessels were active in the QLD fishery, the lowest number since the peak in 1994 of 262 vessels. Recent spanner crab harvests from NSW waters have been about 125 t per year. The spanner crab Managed Area A commercial standardised catch rate averaged 0.739 kg per net-lift in 2014, 24% below the target level of 1.043. Mean catch rates declined in the commercial fishery in 2014, although the magnitude of the decreases was highest in the area north of Fraser Island. The NSW–QLD survey catch rate in 2014 was 16.849 crabs per ground-line, 22% above the target level of 13.972. This represented a decrease in survey catch rates of 0.366 crabs per ground-line, compared to the 2013 survey. The Queensland spanner crab total allowable harvest (quota) was set at 1923 t in 2012 and 2013. In 2014, the quota was calculated at the base level of 1631 t. However, given that the 2012 fisheryindependent survey was not undertaken for financial reasons, stakeholders proposed that the total allowable commercial catch (TACC) be decreased to 1777 t; a level that was halfway between the 2012/13 quota of 1923 t and the recommended base quota of 1631 t. The results from the current analysis indicate that the quota for the 2015-2016 financial year be decreased from 1777 t to the base quota of 1631 t.

Mechanics of transition in an axisymmetric laminar boundary layer on a circular cylinder

Measurements of the growth of artificially generated turbulent spots and intermittency distribution in the transition region on a circular cylinder in axial flow show that the instability Reynolds number of 11,000 has a marked effect on the properties. In particular, it is found that the spot production in the initial region when a single turbulent spot has not yet wrapped around the cylinder and the propagation is essentially two-dimensional, is significantly altered. But the transition in the downstream or latter region, where most of the turbulent spots propagate onedimensionally (like the turbulent plugs in a pipe), is not affected. When the radius Reynolds number is more than 11,000, the intermittency law in the initial region is essentially the same as in twodimensional flow on a flat plate and in the latter region it is the one-dimensional flow in a pipe, the demarcation between the two regions being quite sharp.

Two-dimensional heat conduction with phase change in a semi-infinite mould

Analytical solution of a 2-dimensional problem of solidification of a superheated liquid in a semi-infinite mould has been studied in this paper. On the boundary, the prescribed temperature is such that the solidification starts simultaneously at all points of the boundary. Results are also given for the 2-dimensional ablation problem. The solution of the heat conduction equation has been obtained in terms of multiple Laplace integrals involving suitable unknown fictitious initial temperatures. These fictitious initial temperatures have interesting physical interpretations. By choosing suitable series expansions for fictitious initial temperatures and moving interface boundary, the unknown quantities can be determined. Solidification thickness has been calculated for short time and effect of parameters on the solidification thickness has been shown with the help of graphs.

Constructing Ethical Patterns in Times of Globalization : Hans Küng's Global Ethic Project and Beyond

The purpose of this study is to evaluate contemporary philosophical models for global ethics in light of the Catholic theologian Hans Küng s Global Ethic Project (Projekt Weltethos). Küng s project starts with the motto, No survival without world ethos. No global peace without peace between religions. I will use the philosophically multidimensional potential of Projekt Weltethos in terms of its possible philosophical interpretations to evaluate the general discussion of global ethics within political philosophy today. This is important in its own right, but also because through it, opportunities will emerge to articulate Küng s relatively general argument in a way that leaves less room for mutually contradictory concretizations of what global ethics ultimately should be like. The most important question in this study is the problem of religious and ideological exclusivism and its relation to the ethically consistent articulation of global ethics. I will first explore the question of the role of religion as the basis for ethics in general and what Küng may mean by his claim that only the unconditional can oblige unconditionally. I will reconstruct two different overall philosophical interpretations of the relationship between religious faith and human rationality, each having two different sub-divisions: a liberal interpretation amounts to either a Kantian-Scheiermacherian or a Jaspersian view, whereas what I call postliberal interpretation amounts to either an Aristotelian-Thomistic or an Augustinian view. Thereafter, I will further clarify how Küng views the nature of ethics beyond the question of its principal foundation in religious faith: Küng searches for a middle way between consequentialist and non-consequentialist ethics, a way in which the latter dimension has the final stake. I will then set out to concretize further this more or less general notion of the theoretical potential of Projekt Weltethos in terms of certain precise philosophico-political models. I categorize these models according to their liberal or postliberal orientation. The liberal concretization leads me to consider a wide spectrum of post-Kantian and post-Hegelian models from Rawls to Derrida, while the alternative concretization opens up my ultimate argument in favor of a postliberal type of modus vivendi. I will suggest that the only theoretically and practically plausible way to promote global ethics, in itself a major imperative today, is the recognition of a fundamental and necessary contest between mutually exclusive ideologies in the public sphere. On this basis I will proceed to my postliberal proposal, namely, that a constructive and peaceful encountering of exclusive difference as an ethical vantage point for an intercultural and inter-religious peace dialogue is the most acute challenge for global ethics today.

Sangen ialo Rucous : Schwenckfeldiläisten rukouskirja Mikael Agricolan lähteenä

Sangen ialo Rucous. The prayer book of the Schwenckfeldiens as a source for Michael Agricola The significance of the prayer book published by the Finnish reformer Michael Agricola in the year of 1544 has not been comprehended enough among the prayer literature of the Reformation century. Especially in foreign research literature one of the era s most extensive and versatile prayer books has been practically disregarded. According to the prayer book, Agricola appears to be a traditionalist, who derives most of his source material from medieval and old church prayer books. The low number of the prayers from Evangelical prayer books is noteworthy. The study in hand examines Agricola s theology expressed in his translation work of the prayer book of the mystic spiritualistic Schwenckfeldien movement. The prayer book of the Schwenckdeldiens diverged from Lutheranism was called Bekantnus der sünden and it was composed around the year of 1526. Agricola is the only prayer book collector who has regarded it as necessary to add all the 45 prayers of the Schwenckfeldien prayer book and its introduction to his book. In the prayers containing the Schwenckfeldien communion theology and Christology Agricola has not changed the content of the text, apparently because he was not aware of the problems involved in the Schwenckfeldien theology. On a few occasions Agricola added points of view concerning the church, priesthood, preaching the Word and sacraments to his prayers, which the Schwenckfeldiens despised. From the ten additions four Agricola created himself, the rest he borrowed from Wolfgang Capito s prayer book. As a source Agricola used Capito s Latin prayer book together with the German text from Bekantnus. When looking at the studied material, Agricola does not turn out to be a creative translator. Even though he had a model for a less restricted translation in Wolfgang Capito s prayer book, he sticks to his habit of translating word by word. Because not even a good example has had a liberating effect on his translation principles, Agricola cannot be considered a theologically orientated writer. The translation of the Schwenckfeldien prayers Agricola starts with Capito s prayer book. Very soon he takes the Bekantnus alongside Capito s text and abandons the use of Capito s prayer book in the middle of the translation process. Comparing Agricola s translation with the two texts in different languages has made it possible to create the disposition theory described above. On the basis of the disposition theory it can be concluded that Agricola first worked out a precise plan for his prayer book. Then he translated prayers theme by theme using multiple sources at the same time. Later Agricola fixed the disposition, which does not seem to have a direct paragon. From the prayers of the Schwenckfeldien prayer book Agricola translated 26 texts using the Bekantnus as an only base, from Capito s prayer book he translated four texts and 17 texts he translated using the two basic texts simultaneously. In the previous studies, words and texts added by Agricola have been examined as one problem unit. In this study the additions have been placed into three different categories: additions consequential on tautological parataxis, specifying additions and additions significant to the content. Due to Agricola s meticulous translation techniques, there are so few additions. Agricola does not show his own creativity even in the additions significant to the content but uses there some complete sentences or word fragments from the other prayers he has translated. In the translations of the prayers there are some unique appearing words and the analysis of the translation work shed a new light on the background of their first literary appearance in Finnish. Agricola s linguistic abilities turned out to be great. In those prayers where Agricola uses both the German and Latin basic texts at the same time, the translation process is a very intensive twine made on the basis of the two sources.

Geometry of the de-Sitter universe

By making use of the fact that the de-Sitter metric corresponds to a hyperquadric in a five-dimensional flat space, it is shown that the three Robertson-Walker metrics for empty spacetime and positive cosmological constant, corresponding to 3-space of positive, negative and zero curvative, are geometrically equivalent. The 3-spaces correspond to intersections of the hyperquadric by hyperplanes, and the time-like geodesics perpendicular to them correspond to intersections by planes, in all three cases.

Studies on the Effects of Property Taxation, Rent Control and Housing Allowances

Tämä väitöskirja koostuu asuntomarkkinoiden taloustieteellistä analyysia esittelevästä johdantoluvusta ja kolmesta tutkimuksesta, joissa analysoidaan asuntomarkkinoihin vaikuttavia politiikkatoimenpiteitä. Luvussa 2 tutkitaan Suomen kiinteistöverojärjestelmän vaikutusta asuntorakentamiseen. Vuonna 2001 tehtiin uudistus, jonka myötä kunnat voivat verottaa rakentamatonta asuintonttia korkeammalla veroasteella kuin rakennettua tonttia. Maanomistajan rakentamispäätöksen teoreettisen mallin mukaan rakentamattoman tontin korotettu kiinteistöveron pitäisi nopeuttaa rakentamista, mutta toisaalta myös rakentamiseen investoitu rahamäärä saattaa muuttua. Asuintonttien kiinteistöverojen yleinen taso ei vaikuta maanomistajan käyttäytymiseen, sillä tontin verotusarvo ei riipu rakentamispäätöksestä. Vain rakentamattoman ja rakennetun tontin veroasteiden erolla on merkitystä. Empiiriset tulokset ovat sopusoinnussa teorian kanssa. Tulosten mukaan prosenttiyksikön nousu rakentamattoman ja rakennetun tontin veroasteiden erossa lisää omakotialoitusten määrää viidellä prosentilla lyhyellä aikavälillä. Luvussa 3 analysoidaan vuokrasääntelystä vuokralaisille aiheutuvia hyötyjä ja haittoja. Vuokrasäännellyissä asunnoissa asuvat kotitaloudet hyötyvät vuokrasääntelystä alhaisen vuokran muodossa. Heille saattaa kuitenkin koitua myös haittaa siitä, että toiveita vastaavan asunnon löytäminen on vuokrasääntelytilanteessa vaikeaa, koska vapaille asunnoille on suuri määrä ottajia. Vapaarahoitteisen vuokra-asuntokannan vuokrien sääntely purettiin Suomessa asteittain vuosina 1992–1995. Tutkimuksen empiiriset tulokset viittaavat siihen, että vuokrasääntelyn aiheuttamista suurista eroista halutun ja todellisen asuntokulutuksen välillä koituvat hyvinvointitappiot kumosivat merkittävän osan matalien vuokrien hyödyistä vuokralaisille. Luvussa 4 tutkitaan Suomen asumistukijärjestelmän kannustinvaikutuksia. Asumistuen määrää rajoittavat asunnon pinta-alalle ja neliövuokralle asetetut ylärajat. Neliövuokrarajoite voidaan tulkita asumisen laatua rajoittavana tekijänä. Tutkimuksen teoreettisessa osassa osoitetaan, että asumistukijärjestelmä luo vahvat kannustimet muuttaa asuntoihin, joissa pinta-ala- ja laaturajoitteet purevat. Empiiristen tulosten mukaan asumistukeen oikeutetut kotitaloudet eivät näytä reagoivan kannusteisiin. Tukeen oikeutettujen kotitalouksien asumisvalinnat suhteessa pinta-ala ja laaturajoitteisiin vastaavat muiden kotitalouksien valintoja ja asunnonvaihdon mahdollistama potentiaalinen asumistuen lisäys ei nosta muuttotodennäköisyyttä. Muuttamiseen liittyvät kustannukset ja vajavaiset tiedot tukijärjestelmästä saattavat selittää heikkoa reagointia asumistuen luomiin kannustimiin. Toinen mahdollinen selitys on asumistuen vajaakäyttö. Tutkimuksen mukaan vain 70–80 prosenttia asumistukeen oikeutetuista kotitalouksista nostaa tukea. Asumistuen hyödyntämisen todennäköisyys riippuu koulutustasosta, tuen määrästä ja tulo-odotuksista.