Room-temperature highly anisotropic ferromagnetism and uniaxial spin amplification in (In,Mn)As quantum dots

The hole-mediated ferromagnetism in (In,Mn)As quantum dots is investigated using the k center dot p method and the mean field model. It is found that the (In,Mn)As quantum dot can be ferromagnetic at room temperature when there is one hole in the dot. For the spherical quantum dots, the Curie temperature decreases as the diameter increases, and increases as the effective composition of magnetic ions increases. It is interesting to find that the (In,Mn)As oblate quantum dot has highly anisotropic Zeeman splitting and ferromagnetism due to the spin-orbit coupling effect, which can be used as an uniaxial spin amplifier. (c) 2008 American Institute of Physics.

High-power operation of uncoated strain-compensated quantum cascade lasers at 4.8 mu m

High-power operation of uncoated 22-mu m-wide quantum cascade lasers (QCLs) emitting at lambda approximate to 4.8 mu m is reported. The emitting region of the QCL structure consists of a 30-period strain-compensated In0.68Ga0.32As/In0.37Al0.63As superlattice. For a 4-mm-long laser in pulsed mode, a peak output power is achieved in excess of 2240mW per facet at 81K with a threshold current density of 0.64kA/cm(2). The effects of varying the cavity lengths from 1 to 4mm on the performances of the QCLs are analysed in detail and the low waveguide loss of only about 1.4 cm(-1) is extracted.

Design of quantum cascade microcavity lasers based on Q factor versus etching depth

The choice of the etching depth for semiconductor microcavities is a compromise between a high Q factor and a difficult technique in a practical fabricating process. In this paper, the influences of the etching depth on mode Q factors for mid-infrared quantum cascade microcylinder and microsquare lasers around 4.8 and 7.8 mu m are simulated by three-dimensional (3D) finite-difference time-domain (FDTD) techniques. For the microcylinder and the microsquare resonators, the mode Q factors of the whispering-gallery modes (WGMs) increase exponentially and linearly with the increase in the etching depth, respectively Furthermore, the mode Q factors of some higher order transverse WGMs may be larger than that of the fundamental transverse WGM in 3D microsquares. Based on the field distribution of the vertical multilayer slab waveguide and the mode Q factors versus the etching depth, the necessary etching depth is chosen at the position where the field amplitude is 1% of the peak value of the slab waveguide. In addition, the influences of sidewall roughness on the mode Q factors are simulated for microsquare resonators by 2D FDTD simulation. (C) 2009 Optical Society of America

A mini-staged multi-stacked quantum cascade laser for improved optical and thermal performance

In this paper, a mini-staged multi-stacked quantum cascade laser structure with a designed wavelength of 4.7 mu m is presented. By introducing five 0.5 mu m thick high thermal conductivity InP interbuffer layers, the 60-stages active region core of the quantum cascade laser is divided into six equal parts. Based on simulation, this kind of quantum cascade laser with a 10 mu m ridge width gives nearly circular two-dimensional far-field distribution (FWHM = 32.8 degrees x 29 degrees) and good beam quality parameters M-2 = 1.32 x 1.31 in the fast axis (growth direction) and the slow axis (lateral direction). Due to the enhancement of lateral heat extraction through the interbuffer layers, compared to the conventional structure, a decrease of about 5-6% for the maximum temperature in the active region core of the mini-staged multi-stacked quantum cascade laser with indium-surrounded and gold-electroplated packaging profiles is obtained at all possible dissipated electrical power levels.

Photonic crystal distributed feedback quantum cascade laser fabricated with holographic technique

Electrically pumped, edge-emitting, singlemode operation of a two-dimensional photonic crystal distributed feedback (PCDFB) quantum cascade laser emitting at similar to 7.8 mu m is demonstrated. The two-beam holographic technique combined with wet-etching process is successfully used to de. ne a square-lattice PCDFB structure on the top grating layer of the laser. This simple PC fabrication method may open exciting opportunities for the wide application of PCDFB lasers.

Solid source MBE growth of quantum cascade lasers

High material quality is the basis of quantum cascade lasers (QCLs). Here we report the solid source molecular beam epitaxy (MBE) growth details of realizing high quality of InGaAs/InAlAs QCL structures. Accurate control of material compositions, layer thickness, doping profile, and interface smoothness can be realized by optimizing the growth conditions. Double crystal x-ray diffraction discloses that our grown QCL structures possess excellent periodicity and sharp interfaces. High quality laser wafers are grown in a single epitaxial run. Room temperature continuous-wave (cw) operation of QCLs is demonstrated.

Holographic fabricated photonic-crystal distributed-feedback quantum cascade laser with near-diffraction-limited beam quality

We demonstrate the fabrication and characterization of photonic-crystal distributed-feedback quantum cascade laser emitting at 4.7 mu m. The tilted rectangular-lattice PCDFB structure was defined using a multi-exposure of two-beam holographic lithography. The devices exhibit the near-diffraction-limited beam emission with the full width at half maximum of the far-field divergence angles about 4.5 degrees and 2.5 degrees for stripe widths of 55 mu m and 95 mu m, respectively. Single-mode emission with a side mode suppression ratio of approximate to 20 dB is achieved in the temperature range (80-210 K). The single-facet output power is above 1 W for a 95 mu m x 2.5 mm laser bar at 85 K in pulsed operation. (C) 2009 Optical Society of America

Quasi-continuous-wave operation of AlGaAs/GaAs quantum cascade lasers

Quasi-continuous-wave operation of AlGaAs/GaAs-based quantum cascade lasers (lambda similar to 9 mu m) up to 165 K is reported. The strong temperature dependence of the threshold current density and its higher value in high duty cycle is investigated in detail. The self-heating effect in the active region is explored by changing the operating duty cycles. The degradation of lasing performance with temperature is explained. (c) 2005 Elsevier B.V. All rights reserved.

8 mu m strain-compensated quantum cascade laser operating at room temperature

We report on the material growth and device performance characterization of a strain-compensated In0.54Ga0.46As/In0.51Al0.49As quantum cascade laser at lambda similar to 8 mu m. For 2 mu s pulse at a 5 kHz repetition rate, laser action is achieved up to room temperature (30 degrees C). The tuning coefficient d lambda/dT is 1.37 nm K-1 between 83 K and 163 K and 0.60 nm K-1 in the range from 183 K to 303 K. The peak output power is reported to be similar to 11.3 mW per facet at 293 K and the corresponding threshold current density is 5.69 kA cm(-2).

Growth of a periodic InP-based heteroepitaxial structure for a quantum cascade laser

The route to grow InP-based heteroepitaxial structure for quantum cascade laser by molecular beam epitaxy is reported. Optimized growth conditions including substrate temperature, V/III ratio, growth rates, doping levels and interface control are summarized. Double crystal Xray diffraction and cross-sectional transmission electron microscopy disclose that our grown InP-based heteroepitaxial structure for quantum cascade laser has excellent periodicity and sharp interfaces. (C) 2005 Elsevier B.V. All rights reserved.

Energy band design for Si/SiGe quantum cascade laser

This paper introduces in detail the working principle of Si/SiGe Quantum cascade laser(QCL). Appropriate parameters are used to calculate the hole subband structure of Si/Si1-xGex quantum well using a six-band k center dot p method. The dispersion relation and energy band for different layer thickness and compositions are investigated. Meanwhile, the energy separations between hole subbands in Si/Si1-xGex/Si quantum wells are also analyzed. Finally the calculated results are used for the Si/SiGe QCL design, which will be beneficial to the structure optimization of Si/SiGe QCL.

Low-threshold high-temperature operation of lambda similar to 7.4 mu m quantum cascade lasers

We report low-threshold high-temperature operation of 7.4 mu m strain-compensated InGaAs/InAlAs quantum cascade lasers (QCLs). For an uncoated 22-mu m-wide and 2-mm-long laser, the low-threshold current densities, i.e. 0.33 kA/cm(2) at 81 K in pulsed mode and 0.64 kA/cm(2) at 84 K in cw mode, are realized. High-temperature operation of uncoated devices, with a high value of 223 K, is achieved in cw mode.

Low threshold current density operation of strain-compensated quantum cascade laser

We report the low threshold current density operation of strain-compensated In0.64Ga0.36As/In0.38Al0.62As quantum cascade lasers emitting near 4.94 mu m. By employing an enlarged strain-compensated structure and optimizing the injector doping density, a rather low threshold current density of 0.57 kA/cm(2) at 80K is achieved for an uncoated 20-mu m-wide and 2.5-mm-long laser.

Design of Low-Loss Surface-Plasmon Quantum Cascade Lasers

National Research Projects of China 60525406 60736031 60806018 60906026 2006CB604903 2007AA03Z446 2009AA03Z403

Design and characteristics of quantum cascade laser-based CO detection system

National High Technology Research and Development Program of China 2007AA03Z112；Program of Ministry of Education of China 20060183030；Program of Jilin Provincial Science and Technology Department of China 20070709；Program of Bureau of Science and Technology of Changchun City 2007107