Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

Identification of plantlet genetic origin in polyembryonic mango (Mangifera indica, L.) cv. Rosinha seeds using RAPD markers

Mango can be propagated by seeds or by grafting. For commercial purpose, grafting is the most appropriate method because it maintains the genetic characters from the propagated variety. To obtain grafted mango it is important to use polyembryonic varieties as rootstock since they produce a zygotic and many nucellar plantlets. The nucellar plantlets maintain the genetics of the mother-plant thus, are preferred for grafting since they supposedly give more uniformity to the orchard. In general, nurserymen use the most vigorous plantelet to graft, believing that they are nucellar. But, orchard disuniformities on height and yield are very common among mango trees of commercial orchards in Northeast region. The objective of this paper was to identify the genetical origin of plantlets from polyembryonic seeds of Rosinha variety using Random Amplified Polymorphic DNA (RAPD) markers. Moreover, the position of the zygotic embryo and the percentage of the vigorous zygotic and nucellar plantlets was also determined. It was obtained an elevated taxa of vigorous zygotic plantlets which possibly explains the disuniformity on height of trees at commercial mango orchards.

Irrigation performance and gross water productivity in furrow-irrigated ornamental tree production

In the ornamental plant production region of Girona (Spain), which is one of the largest of its kind in southern Europe, most of the surface is irrigated using wide blocked-end furrows. The objectives of this paper were: (1) to evaluate the irrigation scheduling methods used by ornamental plant producers; (2) to analyse different scenarios in order to assess how they affect irrigation performance; (3) to evaluate the risk of deep percolation; and (4) to calculate gross water productivity. A two-year study in a representative commercial field, planted with Prunus cerasifera ‘Nigra’, was carried out. The irrigation dose applied by the farmers was slightly smaller than the required water dose estimated by the use of two different methods: the first based on soil water content, and the second based on evapotranspiration. Distribution uniformity and application eff iciency were high, with mean values above 87%. Soil water content measurements revealed that even at the end of the furrow, where the infiltrated water depth was greatest, more than 90% of the infiltrated water was retained in the shallowest 40 cm of the soil; accordingly, the risk of water loss due to deep percolation was minimal. Gross water productivity for ornamental tree production was € 11.70 m–3, approximately 20 times higher than that obtained with maize in the same region.

Meat characteristics of chickens from an F1 cross of two improved Spanish breeds depending on slaughter age

The present study analysed the meat characteristics of i) improved Castellana Negra chickens slaughtered at 18 weeks (CN-18) and ii) F1 crossbred chickens from improved Castellana Negra hens and improved Penedesenca Negra cocks (CNPN) slaughtered at 12 weeks and 18 weeks of age (young and adult animals, respectively). Purebred and crossbred specimens were compared at similar weights (CN-18 and CNPN-12) and ages (CN-18 and CNPN-18). The protein content of the meat was similar for the three types of animals; heavier animals (CNPN-18) had more fat than those slaughtered at lower weights (CNPN-12 and CN-18). Adults had a higher saturated fatty acid content and the young CNPN chickens had more monounsaturated fatty acids than CN chickens. In the CNPN adults, less water was lost during cooking, which is directly related to the juiciness of the meat. With regard to sensory analysis, a darker colour was observed in the meat as much as the internal fat of adult animals, in addition to greater colour uniformity. The meat of young CNPN birds was juicier, whereas that of the CN chickens was more fibrous. Therefore, we conclude that meat from CNPN chickens presents chemical, physical, and sensorial characteristics that make these animals a genetic base for alternative poultry production.

Preferential reproduction mode of hermaphrodite papaya plant (Carica papaya L; Caricaceae)

This research was done to study the reproductive system of papaya hermaphrodite plant based on the histochemical nature of pollen grain, stigma receptivity, in vivo pollen grain germination and pollen:ovule ratio. In the histochemical analysis, pollen grains were stained by using Sudan IV and I2KI solution ; the stigma receptivity was assessed by alpha-naphthtyl acetate solution in closed and opened flowers. Pollen germination and pollen tube growing were examined in flower buds near anthesis with 0.1% aniline blue. To estimate the pollen:ovule ratio , anthers from each flower bud were dissected and all pollen grains were counted; ovules were dissected from ovaries and were counted under stereomicroscope. The results indicated that papaya pollen grains are of lipidic nature; the stigmas were receptive before the opening and until 48 hours after opening; the pollen grains germinated and emitted polinic tube before flower opening and the pollen:ovule ratio indicated the predominance of autogamous reproductive system. These results indicate that hermaphrodite papaya trees is preferentially of optional autogamous with cleistogamy.

El clític 'es' i la construcció anticausativa

L'objectiu d'aquest article és defensar la responsabilitat del component lèxic pel que fa a la presència (o l'absència) del clític en la construcció anticausativa. Es presenten proves que justifiquen que les argumentacions sobre aquest fenomen des de la semàntica o l'estructura eventual, que són les més prolíferes en la bibliografia, no són vàlides per a tots els verbs que participen en l'estructura sintàctica esmentada. Es considera que ni la sintaxi ni la morfologia tampoc poden donar llum dels fets i es proposa que l'explicació de la manca d'uniformitat pel que fa a l'aparició del pronom ha de trobar-se a partir de fenòmens que no es poden discernir en observar només l'estat actual de la llengua.

Monitoring the viability of citrus rootstocks seeds stored under refrigeration

The citrus nursery tree is produced through the bud grafting process, in which rootstock is usually grown from seed germination. The objective of this research was to evaluate, in two dissimilar environmental conditions, the viability and polyembryony expression of five citrus rootstocks seeds stored in different periods under refrigeration. The rootstock varieties evaluated were: Rangpur lime (Citrus limonia Osb. cv. Limeira), Trifoliate orange (Poncirus trifoliata Raf. cv. Limeira), Citrumelo (P. trifoliata x C. paradisi Macf. cv. Swingle), Sunki mandarin (C. sunki Hort. ex Tanaka) and Volkamer lemon (C. volkameriana Ten. & Pasq. cv. Catania 2). The experimental design was the randomized blocks in a 11 x 5 x 2 factorial scheme, evaluating from time zero to the tenth month of storage, the five varieties of rootstock in two environments: germination and growth B.O.D type chamber (Biological Oxygen Demand - Eletrolab Brand Model FC 122) at 25 °C; and greenhouse seedbed with partial temperature control (22 °C to 36 °C) and humidity control (75-85%). The plot had 24 seeds in four replicates, using trays with substrate in greenhouse and Petri dishes with filter paper in B.O.D. chamber. The seed germination rate and polyembryony expression were evaluated monthly. It was concluded that Trifoliate and Citrumelo Swingle seeds can be stored for up to seven months, while Volkamer lemon, Rangpur lime and Sunki seeds can be stored for up to ten months. The polyembryony expression rate was slightly higher when measured in greenhouse than in B.O.D. chamber and remained stable in both environments until the seventh month, from which dropped sharply. Citrumelo Swingle seeds expressed the highest polyembryony rate (18.8%), followed by Rangpur lime and Volkamer lemon (average value of 13.7%), Sunki (9.4%) and Trifoliate (3.2%). Despite some differences among varieties, the viability of rootstock stored seeds can be monitored either in the greenhouse or in B.O.D. germination chamber, the latter being the faster and more suitable method.

Conservation of Campomanesia adamantium (CAMB.) O. berg seeds in different packaging and at varied temperatures

This article aims at evaluating the effects of different packaging and varied storage temperatures on the germination potential of seeds of Campomanesia adamantium Camb. O. Berg. The seeds were packaged in glass, aluminum foil and plastic containers, or maintained inside intact fruits at 5, 10 and 15 ºC during 0, 7, 14 and 21 days. After these periods the seeds were sown in Germitest® germination paper and maintained in incubation chambers at 25 ºC under constant white light for 42 days. Seed moisture contents were evaluated both before and after storage, as well as germination percentages, germination speed index, root and aerial portion of seedlings lengths, and total dry weights. All possible combinations of packing materials, temperatures and storage times were tested, with four repetitions of 25 seeds for each treatment. C. adamantium seeds showed initial water contents of 31.5%. Glass and aluminum packaging were efficient at maintaining the water content of the seeds, and provided greater germination speed index than the other packaging materials. Germination percentages, seedlings lengths and dry weights did not vary among the different temperatures tested. C. adamantium seeds can be stored for up to 21 days at temperatures between 5 and 15 ºC without altering their physiological quality. In terms of cost-benefit efficiencies, these seeds can be stored without significant damage for 21 days while still inside the fruits at temperatures of 5, 10 or 15 ºC.

Ympäristöjärjestelmien kehittäminen rakennustuotealan yrityksen Keski-Euroopan toimipaikoissa

Tämän diplomityön tavoitteena oli antaa kehittämisehdotuksia, joilla voidaan parantaa rakennustuotealan yrityksen ympäristöjärjestelmien kustannustehokkuutta sekä ympäristöpolitiikkaan liittyvän jatkuvan parantamisen yhtenäistä toteutumista eri toimipaikoilla. Lähtökohtana olivat havainnot siitä, että melko pienissä toimipaikoissa laatu- ja ympäristöasiat kattavan toimintajärjestelmän rakentaminen ja ylläpitäminen vie paljon resursseja. Lisäksi selvitettiin uuden ISO 14001-standardiehdotuksen mahdollisia vaikutuksia käytössä oleviin ympäristöjärjestelmiin. Tutkimusmenetelminä käytettiin eri sertifiointielimille tehtyä haastattelua, toimipaikkojen ympäristövastaaville lähetettyä kyselyä, verkkosivuille kohdistettua kilpailijaseurantaa sekä selvitystä uuden ISO 14001- standardiehdotuksen muutoksista. Eri toimipaikkojen ympäristöjärjestelmien yhdistäminen saman sertifikaatin alle oli kaikkien sertifiointielinten edustajien mielestä hyvä tapa vähentää järjestelmien ulkoisesta valvonnasta aiheutuvia kustannuksia ja parantaa järjestelmien tehokkuutta. Ulkoisten kustannusten aleneminen on noin yksikolmasosa, joka syntyy ensinnäkin sertifikaattimaksujen alenemista ja toisaalta sertifiointipäivien vähenemisestä. Sertifikaattimaksut alenevat, koska yhdistetyssä järjestelmässä sertifikaatteja on vähemmän, ja sertifiointipäivien määrä vähenee, koska yhdistetyn järjestelmän ulkoisessa valvonnassa käytetään otanta -periaatetta. Kilpailijaseurannan osalta havaittiin, että yrityksen verkkosivuilla kerrottiin kilpailijoita paremmin ympäristö- sekä laatujärjestelmistä. Kehitettävää on eri maiden verkkosivujen yhtenäisyydessä ja ympäristö- ja laatupolitiikan esittämisessä. Nämä politiikat tulee olla esillä, koska järjestelmästandardit edellyttävät politiikkojen julkisuutta. Ympäristövastaaville tehdyn kyselyn perusteella havaittiin, että tällä hetkellä toimipaikoilla käytössä olevissa ympäristäjärjestelmissä on eroavuuksia. Syynä tähän on muun muassa järjestelmien eri-ikäisyys, maiden toimipaikkojen erilainen lainsäädäntö sekä erilaiset resurssit. Kehittämistä on erityisesti ympäristönnäkökohtien tunnistamisessa ja merkittävien ympäristönäkökohtien valinnassa, ympäristöjärjestelmän tavoitteissa ja päämäärissä sekä käytettävissä indikaattoreissa. Näiden osalta tulee lisätä koulutusta ja ohjeistusta. Uuden ISO 14001 -standardin muutoksia tarkasteltaessa havaittiin, ettei se aiheuta suuria muutostarpeita nykyisiin ympäristöjärjestelmiin. Standardin suurimmat muutokset ovat tulleet tekstin rakenteeseen, joka on nyt selkeälukuista ja yhteensopivampaa ISO 9001 laatuhallintastandardin kanssa. Standardi painottaa entistä standardia enemmän tuotteista aiheutuvia ympäristönäkökohtia, mutta on muistettava, että sen vaikutukset nykyisiin ympäristöjärjestelmiin tiedetään vasta, kun sitä aletaan tulkita. Tulosten perusteella päädyttiin siihen, että ympäristöjärjestelmien yhdistäminen saman sertifikaatin alle on tehokkain tapa parantaa kustannustehokkuutta sekä parantaa ympäristöpolitiikkaan liittyvää jatkuvaa parantamista. Ulkoisten kustannusten aleminen ei ole tärkein syy järjestelmien yhdistämiseen, koska yhdistämisen alkuvaiheessa se aiheuttaa sisäisten kustannusten lisääntymistä. Jatkossa yhdistämisestä voidaan odottaa myös sisäisten kustannusten säästöjä, koska yhdistäminen vähentää päällekkäistä työtä. Yrityksen ympäristöpolitiikan mukaiseen jatkuvaan parantamiseen järjestelmien yhdistäminen vaikuttaa positiivisesti usealla tavalla, ja tätä voidaan pitää kustannussäästöjä tärkeämpänä syynä sertifikaattien yhdistämiseen. Se yhtenäistää toimintatapoja ja lisää yhteistyötä, mikä vaikuttaa ympäristöpolitiikan yhtenäiseen toteutumiseen.

Papaya seedlings growth using a low-cost, automatic watering controller

The study assessed growth and physiological parameters of 'Sunrise Golden' and 'Tainung 01' papaya seedlings grown in 280mL plastic tubes and watered using a low-cost automatic irrigation system adjusted to operate at substrate water tension for starting irrigation (STI) of 3.0, 6.0 or 9.0 kPa. The water depths applied by the dripping system and drainage were monitored during germination and seedling growth. Germination, emergence velocity index (EVI), leaf area, plant height, shoot and root dry weight, stomatal conductance, relative water content (RWC) and relative chlorophyll content (RCC) were evaluated. Soil nutrient levels were determined by electrical conductivity (EC). Water use efficiency (WUE) corresponded to the ratio of plant dry mass to depth of water applied. STI settings did not affect papaya germination or EVI. System configuration to 3.0 and 6.0 kPa STI exhibited the highest drainage and lowest EC and RCC, indicating soil nutrient loss and plant nutrient deficiency. Drainage was greater in tubes planted with the 'Tainung 01' variety, which developed smaller root systems and lower stomatal conductance than 'Sunrise Golden' seedlings. The highest values for shoot dry weight and WEU were obtained at 6.0 kPa STI for 'Sunrise Golden' (0.62 g and 0.69 g L-1) and at 9.0 kPa in 'Tainung 01' (0.35 g and 0.82 g L-1). RWC at 9.0 kPa STI was lower than at 3.0 kPa in both varieties. The results indicate that the low-cost technology developed for irrigation automation is promising. Even so, new studies are needed to evaluate low-flow irrigation systems as well as the nutrient and water needs of different papaya varieties.

Biological Flora of the British Isles: Ambrosia artemisiifolia

1. This account presents information on all aspects of the biology of Ambrosia artemisiifolia L. (Common ragweed) that are relevant to understanding its ecology. The main topics are presented within the standard framework of the Biological Flora of the British Isles: distribution, habitat, communities, responses to biotic factors, responses to environment, structure and physiology, phenology, floral and seed characters, herbivores and disease, history, and conservation, impacts and management. 2. Ambrosia artemisiifolia is a monoecious, wind-pollinated, annual herb native to North America whose height varies from 10 cm to 2.5 m according to environmental conditions. It has erect, branched stems and pinnately lobed leaves. Spike-like racemes of male capitula composed of staminate (male) florets terminate the stems, while cyme-like clusters of pistillate (female) florets are arranged in groups the axils of main and lateral stem leaves. 3. Seeds require prolonged chilling to break dormancy. Following seedling emergence in spring, the rate of vegetative growth depends on temperature, but development occurs over a wide thermal range. In temperate European climates, male and female flowers are produced from summer to early autumn (July to October). 4. Ambrosia artemisiifolia is sensitive to freezing. Late spring frosts kill seedlings and the first autumn frosts terminate the growing season. It has a preference for dry soils of intermediate to rich nutrient level. 5. Ambrosia artemisiifolia was introduced into Europe with seed imports from North America in the 19th century. Since World War II, it has become widespread in temperate regions of Europe and is now abundant in open, disturbed habitats as a ruderal and agricultural weed. 6. Recently, the N. American ragweed leaf beetle (Ophraella communa) has been detected in southern Switzerland and northern Italy. This species appears to have the capacity to substantially reduce growth and seed production of A. artemisiifolia. 7. In heavily infested regions of Europe, A. artemisiifolia causes substantial crop-yield losses and its copious, highly allergenic pollen creates considerable public health problems. There is consensus among models that climate change will allow its northward and up-hill spread in Europe.

Histopathology of Colletotrichum gloeosporioides on guava fruits (Psidium guajava L.)

Anthracnose, caused by Colletotrichum gloeosporioides, produces brown lesions on guava fruits, causing severe losses on postharvest. In this study, the infection and colonization of guava fruits by C. gloeosporioides has been examined using scanning and transmission electron microscopy. Fruits at the physiologically mature stage were inoculated with a 10(5) conidia/mL spore suspension. Afterward, fruits were incubated at 25 °C in a wet chamber for periods of 6, 12, 24, 48, 96 and 120 h to allow examination of the infection and colonization process. Conidia germination and appressoria formation occurred six hours after inoculation (h.a.i). Penetration occurred directly via penetration pegs from appressoria, which penetrated the host cuticle 48 h.a.i. Notably, the appressoria did not produce an appressorial cone surrounding the penetration pore. Infection vesicles were found in epidermal cells 96 h.a.i. The same fungal structures were found in epidermal and parenchymal cells of the host 120 h.a.i. Colonization strategy of C. gloeosporioides on guava fruit was intracellular hemibiotrophic.

Kromaattisuuserojen laskentamalli

Työssä esitellään Lappeenrannan teknillisen yliopiston Tietotekniikan osastolla kehitettyä kromaattisuuserojen laskentamallia. Työn keskeisimpinä tavoitteina on luoda tiivis katsaus jo olemassa oleviin värierojen laskentamenetelmien tekniikoihin ja käydä läpi värien havaitsemiseen liittyviä yksityiskohtia. Työn käytännön osuudessa tutkitaan kehitettyä mallia ja esitetään ideoita kehittäen mallia täsmällisemmäksi. Kromaattisuuserojen laskentamalli perustuu MacAdamin määrittelemien ellipsien hyödyntämiseen CIE-1931 kromaattisuusdiagrammissa. Ideana on projisoida ellipsit iso- ja pikkuakseleidensa suhteen vakiosäteisiksi ympyröiksi kolmiulotteiselle pinnalle. Kromaattisuuserot lasketaan pinnalta käyttämällä numeerista menetelmää. Tuloksena todetaan mallin täyttävän osittain sille asetetut vaatimukset ja parantavan CIE-1931 kromaattisuusdiagrammin yhtenäisyyttä erityisesti diagrammin vihreän ja sinisen värin alueilla.

Päällystysyksikön konstruktion kehitys.

Työssä suunniteltiin esisuunnitteluluontoisesti leveän, uutta päällystysmenetelmää soveltavan päällystysaseman konstruktio avainkomponenttien osalta. Ensin perehdyttiin alan kirjallisuuteen ja pyrittiin selvittämään päällystysmenetelmän konstruktiolle asettamia vaatimuksia. Tämän jälkeen pohdittiin rakenteen leveyden ja päällystysnopeuden lisäämisen tuomia ongelmia ja lopuksi ideoitiin havaittuihin ongelmiin ratkaisuja. Virtauskammion mitoituksen, ohikierron vaikutuksen ja virtausta tasoittavien elementtien mitoituksen selvittämiseksi tehtiin CFD laskenta newtonisella ja einewtonisella virtausaineella. Huomattiin painehäviön kasvattamisen ja tasauskammion lisäämisen parantavan päällysteprofiilia. Ohikierron lisäämisen todettiin heikentävän päällysteprofiilia erityisesti reunojen läheisyydessä. Virtauksen jako- ja tasauskammioiden muotoilua muutettiin tukkeutumisriskin pienentämiseksi. Rakenne kokee aina myös muodonmuutoksia paineen-, taipumien- tai lämpötilaerojen seurauksena. Näiden vaikutuksen selvittämiseksi applikointiosaa analysointiin FE -menetelmällä. Todettiin palkin pinnalla olevien lämpötilaerojen olevan suurin yksittäinen päällysteprofiiliin vaikuttava häiriölähde.

Strateginen toimintoperusteisen kustannuslaskentaprojektin ohjaus

Työn päätavoitteena oli tutkia, miten toimintoperusteisia kustannuslaskentaprojekteja (ABC) voidaan ohjata tehokkaammin tulevaisuudessa, ja löytää toimintojohtamisen (ABM) tuki liiketoiminnan strategiselle johtamiselle verkottuvassa yritysmaailmassa. Lisäksi tavoitteena oli määritellä ABC-projektien johtamismallien viitekehys ja vertailla toteutettuja ABC-hankkeita.Toimintolaskentaa ja prosessijohtamista selvitettiin kirjallisuuden ja asiantuntijoiden haastatteluiden avulla. Tutkimuksen empiirisen osan ABC-hankkeiden tiedot pohjautuvat projekteissa tiiviisti mukana olleiden henkilöiden haastatteluihin. Kolmen eri yhtiön hankkeet kuvattiin, ja niiden analysoinnin pohjalta esitettiin mahdollisia jatkotoimenpiteitä liiketoiminnan johtamisen näkökulmasta. Lopuksi työssä pohdittiin myös liiketoiminnan ohjaamisen tulevaisuutta ja jatkotutkimustarpeita.Eri ABC-projektien vertailun pohjalta havaittiin mahdollisia hankekohtaisia kehitysalueita, kuten tietojärjestelmien yhtenäisyys, joustavuus, strateginen oppiminen tulevaisuudessa ja resurssien kohdentaminen. Lisäksi toteutettuja hankkeita arvioitiin liiketoiminnan ohjausta tukevan vuorovaikutteisen resurssisuunnittelun pohjalta. Työssä luotiin ABC-projektien johtamismallien kautta viitekehyksiä mahdollisille jatkohankkeille korostamalla prosessimaisuutta ja ulkoista verkottumista.Lopuksi esitetään, että ennen ABC-hankkeen aloitusta on yrityksen nykyinen tila ja tietojärjestelmät analysoitava. Projektia ei saa toteuttaa vain yhden hyväksi koetun tavan mukaisesti, vaan onnistunut ABC-projektin läpivienti vaatii monien erilaisten toteutus- ja ajattelumallien yhdistämistä. ABC-sovellusten on tuettava sekä operatiivista toimintaa että strategista liiketoiminnan johtamista. Tehokas verkottuminen mahdollistaa lopulta ulkoisten prosessien hallinnan yhdessä organisaation sidosryhmien kanssa.