Formulação e caracterização de pastas espumadas por incorporação de ar e estabilizantes minerais

Cementing operations may occur at various stages of the life cycle of an oil well since its construction until its definitive abandonment. There are some situations in which the interest zones are depleted or have low fracture pressure. In such cases, the adoption of lowdensity cement slurries is an efficient solution. To this end, there are basically three ways to reduce the density of cement slurries: using microspheres, water extending additives or foamed cement. The objective of this study is to formulate, to study and to characterize lowdensity foamed cement, using an air entrainment surfactant with vermiculite or diatomite as water extenders and stabilizers. The methodology consists on preparation and evaluation of the slurries under the American Petroleum Institute (API) and the Brazilian Association of Technical Standards (ABNT) guidelines. Based on calculated densities between 13 and 15 ppg (1.559 and 1.799 g/cm3), the slurries were prepared with fixed surfactant concentration, varying the concentrations of vermiculite and diatomite and were compared with the base slurries. The results of plastic viscosity, yield point and gel strength and the compressive strength for 24 h showed that the slurries presented suitable rheology and mechanical strength for cementing operations in oil wells, and had their densities reduced between 8.40 and 11.89 ppg (1.007 and 1.426 g/cm3). The conclusion is that is possible, under atmospheric conditions, to obtain light weighted foamed cement slurries with satisfactory rheological and mechanical properties by means of air entrainment and mineral additions with extenders and stabilizers effects. The slurries have great potential for cementing operations; applicability in deep wells, in low fracture gradient formations and in depleted zones and bring cost savings by reducing the cementing consumption

Síntese e caracterização do líquido iônico tetrafluoroborato de 1-metil-3-(2,6-(S)-dimetiloct-2-eno)-imidazol como eletrólito para produção de hidrogênio via eletrólise da água

Ionic liquids (ILs) are organic compounds liquid at room temperature, good electrical conductors, with the potential to form as a means for electrolyte on electrolysis of water, in which the electrodes would not be subjected to such extreme conditions demanding chemistry [1]. This paper describes the synthesis, characterization and study of the feasibility of ionic liquid ionic liquid 1-methyl-3(2,6-(S)-dimethyloct-2-ene)-imidazole tetrafluoroborate (MDI-BF4) as electrolyte to produce hydrogen through electrolysis of water. The MDI-BF4 synthesized was characterized by thermal methods of analysis (Thermogravimetric Analysis - TG and Differential Scanning Calorimetry - DSC), mid-infrared spectroscopy with Fourier transform by method of attenuated total reflectance (FTIR-ATR), nuclear magnetic resonance spectroscopy of hydrogen (NMR 1H) and cyclic voltammetry (CV). Where thermal methods were used to calculate the yield of the synthesis of MDI-BF4 which was 88.84%, characterized infrared spectroscopy functional groups of the compound and the binding B-F 1053 cm-1; the NMR 1H analyzed and compared with literature data defines the structure of MDI-BF4 and the current density achieved by MDI-BF4 in the voltammogram shows that the LI can conduct electrical current indicating that the MDI-BF4 is a good electrolyte, and that their behavior does not change with the increasing concentration of water

Evolução diagenética e caracterização dos reservatórios da seção devoniana na Bacia do Rio do Peixe-Nordeste do Brasil

The Rio do Peixe Basin represents a main basin of northeastern Brazil and pioneering work positioned the rocks of this basin in the Early Cretaceous. However, a recent study, based on integrated pollen analysis from three wells, found an unprecedented siliciclastic sedimentary section, in the region, of early Devonian age. Therefore, the present study aims a detailed petrographic and petrological analysis of this devonian section, in the Rio do Peixe Basin and proposes a diagenetic evolution, to understand the characteristics of the porous system, identify the main reservoir petrofacies with the main factors impacting on the quality of these rocks as reservoirs and a quick study on the provenance of this section. The petrographic study was based on samples obtained from subsurface and surface. The diagenetic evolution of petrofacies and its identification were based only on subsurface samples and the study of provenance was based on surface samples. The thin sections were prepared from sandstones, pelites and sandstones intercalated with pelites. The original detrital composition for this section is arcosean and the main diagenetic processes that affected these rocks occur in various depths and different conditions, which resulted in extensive diagenetic variety. The following processes were identified: early fracture and healing of grains; albitization of K-feldspar and plagioclase; siderite; precipitation of silica and feldspar; mechanical infiltration of clay and its transformation to illite/esmectite and illite; autigenesis of analcime; dissolution; autigenesis of chlorite; dolomite/ferrous dolomite/anquerite; apatite; calcite; pyrite; titanium minerals and iron oxide-hidroxide. The occurrence of a recently discovered volcanism, in the Rio do Peixe Basin, may have influenced the diagenetic evolution of this section. Three diagenetic stages affected the Devonian section: eo, meso and telodiagenesis. This section is compositionally quite feldspathic, indicating provenance from continental blocks, between transitional continental and uplift of the basement. From this study, we observed a wide heterogeneity in the role of the studied sandstones as reservoirs. Seven petrofacies were identified, taking into account the main diagenetic constituent responsible for the reduction of porosity. It is possible that the loss of original porosity was influenced by intense diagenesis in these rocks, where the main constituent for the loss of porosity are clays minerals, oxides and carbonate cement (calcite and dolomite)

Avaliação do petróleo por termogravimetria para simulação de curva PEV, fator de caracterização e resíduo de carbono

Petroleum evaluation is analyze it using different methodologies, following international standards to know their chemical and physicochemical properties, contaminant levels, composition and especially their ability to generate derivatives. Many of these analyzes consuming a lot of time, large amount of samples , supplies and need an organized transportation logistics, schedule and professionals involved. Looking for alternatives that optimize the evaluation and enable the use of new technologies, seven samples of different centrifuged Brazilian oils previously characterized by Petrobras were analyzed by thermogravimetry in 25-900° C range using heating rates of 05, 10 and 20ºC per minute. With experimental data obtained, characterizations correlations were performed and provided: generation of true boiling point curves (TBP) simulated; comparing fractions generated with appropriate cut standard in temperature ranges; an approach to obtain Watson characterization factor; and compare micro carbon residue formed. The results showed a good chance of reproducing simulated TBP curve from thermogravimetry taking into account the composition, density and other oil properties. Proposed correlations for experimental characterization factor and carbon residue followed Petrobras characterizations, showing that thermogravimetry can be used as a tool on oil evaluation, because your quick analysis, accuracy, and requires a minimum number of samples and consumables

Caracterização funcional de dois cDNAs de cana-de- açúcar : PKCI e SHAGGY

Flowering is controlled by several environmental and endogenous factors, usually associated with a complex network of metabolic mechanisms. The gene characterization in Arabidopsis model has provided much information about the genetic and molecular mechanisms that control flowering process. Some of these genes had been found in rice and maize. However, in sugarcane this processe is not well known. It is known that early flowering may reduce its production up to 60% at northeast conditions. Considering the impact of early flowering in sugarcane production, the aim of this work was to make the gene characterization of two cDNAs previously identified in subtractive cDNA libraries: scPKCI and scSHAGGY. The in silico analysis showed that these two cDNAs presented both their sequence and functional catalytic domains conserved. The results of transgenic plants containing the overexpression of the gene cassette scPKCI in sense orientation showed that this construction had a negative influence on the plant development as it was observed a decrease in plant height and leaf size. For the scPKCI overexpression in antisense orientation it was observed change in the number of branches from T1 transgenic plants, whereas transgenic T2 plants showed slow development during germination and initial stages of development. The other cDNA analyzed had homology to SHAGGY protein. The overexpression construct in sense orientation did not shown any effect on development. The only difference observed it was an increase in stigma structure. These results allowed us to propose a model how these two genes may be interact and affect floweringdevelopment.

Modelagem molecular na caracterização eletrônica de oligopeptídeos e na descrição quântica da interação fármaco-receptor

In this dissertation, the theoretical principles governing the molecular modeling were applied for electronic characterization of oligopeptide α3 and its variants (5Q, 7Q)-α3, as well as in the quantum description of the interaction of the aminoglycoside hygromycin B and the 30S subunit of bacterial ribosome. In the first study, the linear and neutral dipeptides which make up the mentioned oligopeptides were modeled and then optimized for a structure of lower potential energy and appropriate dihedral angles. In this case, three subsequent geometric optimization processes, based on classical Newtonian theory, the semi-empirical and density functional theory (DFT), explore the energy landscape of each dipeptide during the search of ideal minimum energy structures. Finally, great conformers were described about its electrostatic potential, ionization energy (amino acids), and frontier molecular orbitals and hopping term. From the hopping terms described in this study, it was possible in subsequent studies to characterize the charge transport propertie of these peptides models. It envisioned a new biosensor technology capable of diagnosing amyloid diseases, related to an accumulation of misshapen proteins, based on the conductivity displayed by proteins of the patient. In a second step of this dissertation, a study carried out by quantum molecular modeling of the interaction energy of an antibiotic ribosomal aminoglicosídico on your receiver. It is known that the hygromycin B (hygB) is an aminoglycoside antibiotic that affects ribosomal translocation by direct interaction with the small subunit of the bacterial ribosome (30S), specifically with nucleotides in helix 44 of the 16S ribosomal RNA (16S rRNA). Due to strong electrostatic character of this connection, it was proposed an energetic investigation of the binding mechanism of this complex using different values of dielectric constants (ε = 0, 4, 10, 20 and 40), which have been widely used to study the electrostatic properties of biomolecules. For this, increasing radii centered on the hygB centroid were measured from the 30S-hygB crystal structure (1HNZ.pdb), and only the individual interaction energy of each enclosed nucleotide was determined for quantum calculations using molecular fractionation with conjugate caps (MFCC) strategy. It was noticed that the dielectric constants underestimated the energies of individual interactions, allowing the convergence state is achieved quickly. But only for ε = 40, the total binding energy of drug-receptor interaction is stabilized at r = 18A, which provided an appropriate binding pocket because it encompassed the main residues that interact more strongly with the hygB - C1403, C1404, G1405, A1493, G1494, U1495, U1498 and C1496. Thus, the dielectric constant ≈ 40 is ideal for the treatment of systems with many electrical charges. By comparing the individual binding energies of 16S rRNA nucleotides with the experimental tests that determine the minimum inhibitory concentration (MIC) of hygB, it is believed that those residues with high binding values generated bacterial resistance to the drug when mutated. With the same reasoning, since those with low interaction energy do not influence effectively the affinity of the hygB in its binding site, there is no loss of effectiveness if they were replaced.

Caracterização morfológica e frequência dos estádios do ciclo do epitélio seminífero em preás (Galea spixii Wagler, 1831) criados em cativeiro

Estudos baseados nas características testiculares estão altamente relacionados com a eficiência reprodutiva de varias espécies. Assim, o projeto desenvolvido teve como objetivo identificar as células do epitélio seminífero, caracterizar histologicamente suas associações, que formam os estádios, e determinar a frequência destes. Os fragmentos de testículos, com 30, 45, 60, 75, 90, 105, 120, 150 dias foram coletados no Centro de Multiplicação da Universidade Federal Rural do Semi-Árido (UFERSA), Mossoró/ RN. Passando pelos processos de fixação, lavagens em soluções de concentrações crescentes de álcoois (70-100%), desidratação em xilol, inclusão em Histosec®, preparação das lâminas histológicas, colorações em Hematoxilina e Eosina (HE) e suas fotomicrografias para a caracterização dos núcleos celulares do epitélio germinativo e a definição dos oitos estágios do ciclo do epitélio seminífero (CES) baseados no Método da Morfologia Tubular. Das faixas etárias analisadas todos os animais de 90-150 dias de idade apresentaram todos os estádios do CES. Os estádios I e III foram os que apresentaram maior e menor freqüência, respectivamente. Os animais caracterizados como pré-púberes (30 dias), púberes (45-90 dias de idade) e pós-púberes (105150 dias de idade) apresentaram os estádios I, VIII e IV com uma maior freqüência, respectivamente.

Caracterização biométrica e acúmulo de nutrientes em porta-enxertos de caramboleira cultivada em solução nutritiva

O conhecimento sobre o crescimento e o acúmulo de nutrientes em hipobiotos de caramboleira permite melhor eficiência da adubação na produção de hipobiotos (porta-enxertos). Objetivou-se determinar o crescimento e o acúmulo de nutrientes em hipobiotos de caramboleira cultivada em solução nutritiva. O experimento constituiu de cinco tratamentos, referentes aos tempos de coleta 25; 50; 75; 100 e 125 dias após o transplantio, dispostos em delineamento inteiramente casualizado em seis repetições. As plantas utilizadas foram obtidas de sementes de frutos de caramboleira 'Malásia', cultivadas em vasos com solução nutritiva. Nos diferentes órgãos dos hipobiotos (folhas, caule e raízes), avaliou-se o crescimento e o acúmulo de nutrientes e os índices nutricionais, a cada 25 dias. O ponto de enxertia (6 mm) foi atingido aos 110 dias após o transplantio. A ordem decrescente dos nutrientes acumulados em cada hipobioto produzido é de (em mg por planta): N = 634; K = 368; Ca = 152; Mg = 106; S = 98; P = 88 (em µg por planta) de: Fe = 2.963; Mn = 2.165; B = 722; Zn =780, e Cu = 96. O acúmulo médio de nutrientes é maior nas folhas > caule = raízes. O período de maior exigência de nutrientes pelos hipobiotos é compreendido entre 25-75 dias após o transplantio. As diferentes taxas de acumulação líquida dos nutrientes, nas diferentes partes da caramboleira, nem sempre acompanham a taxa de acumulação de nutrientes do respectivo órgão.

Desenvolvimento de Sistemas Microparticulados Superparamagnéticos Gastro-resistentes para Diagnóstico e Terapêutica

This work aimed to develop a suitable magnetic system for administration by the oral route. In addition to that, it was intended to review the current uses of magnetic systems and the safety related to magnetic field exposure. Methods: Coprecipitation and emulsification/crosslinking were carried out in order to synthesize magnetite particles and to coat them, respectively. Results: According to literature review, it was found that magnetic particles present several properties such as magnetophoresis in magnetic field gradient, production of a surrounding magnetic field, and heat generation in alternated magnetic field. When the human organism is exposed to magnetic fields, several interaction mechanisms come into play. However, biological tissues present low magnetic susceptibility. As a result, the effects are not so remarkable. Concerning the development of a magnetic system for oral route, uncoated magnetite particles did undergo significant dissolution at gastric pH. On the other hand, such process was inhibited in the xylan-coated particles. Conclusions: Due to their different properties, magnetic systems have been widely used in biosciences. However, the consequent increased human exposure to magnetic fields has been considered relatively safe. Concerning the experimental work, it was developed a polymer-coated magnetic system. It may be very promising for administration by the oral route for therapy and diagnostic applications as dissolution at gastric pH hardly took place

Desenvolvimento e caracterização de nanocápsulas de poli (L-lactídeo) contendo benzocaína

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Caracterização físico-química de complexo de inclusão entre hidroximetilnitrofurazona e hidroxipropil-beta-ciclodextrina

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Caracterização analítica e geométrica da metodologia geral de determinação de distribuições de Weibull para o regime eólico e suas aplicações

O regime eólico de uma região pode ser descrito por distribuição de frequências que fornecem informações e características extremamente necessárias para uma possível implantação de sistemas eólicos de captação de energia na região e consequentes aplicações no meio rural em regiões afastadas. Estas características, tais como a velocidade média anual, a variância das velocidades registradas e a densidade da potência eólica média horária, podem ser obtidas pela frequência de ocorrências de determinada velocidade, que por sua vez deve ser estudada através de expressões analíticas. A função analítica mais adequada para distribuições eólicas é a função de densidade de Weibull, que pode ser determinada por métodos numéricos e regressões lineares. O objetivo deste trabalho é caracterizar analítica e geometricamente todos os procedimentos metodológicos necessários para a realização de uma caracterização completa do regime eólico de uma região e suas aplicações na região de Botucatu - SP, visando a determinar o potencial energético para implementação de turbinas eólicas. Assim, foi possível estabelecer teoremas relacionados com a forma de caracterização do regime eólico, estabelecendo a metodologia concisa analiticamente para a definição dos parâmetros eólicos de qualquer região a ser estudada. Para o desenvolvimento desta pesquisa, utilizou-se um anemômetro da CAMPBELL.

Estudo cinético na caracterização do status corporal de zinco na Síndrome de Berardinelli-Seip

Conselho Nacional de Desenvolvimento Científico e Tecnológico

Caracterização fenotípica e genotípica de Staphylococcus aureus resistentes à meticilina isolados na cidade do Natal/RN

Staphylococcus aureus resistente à meticilina (MRSA) é um dos principais agentes de infecções associadas a serviços de saúde em todo o mundo. No Brasil, há a predominância de um clone de MRSA multirresistente denominando clone epidêmico brasileiro (CEB). Entretanto, novos clones nãomultirresistentes com alta virulência têm sido descritos em infecções comunitárias e hospitalares. O objetivo desse estudo foi realizar a caracterização fenotípica e genotípica de cepas de MRSA isoladas na cidade do Natal/RN. Inicialmente avaliamos 60 amostras de S. aureus quanto a resistência à meticilina através de diferentes técnicas fenotípicas, utilizando a detecção do gene mecA por PCR como padrão. O antibiograma de todas as cepas foi realizado utilizando 12 antimicrobianos conforme descrito pelo CLSI. As cepas de MRSA foram caracterizadas geneticamente através da tipagem do cassete cromossômico estafilocócico mec (SCCmec) e da eletroforese em campo elétrico alternado (PFGE). Dos 60 S. aureus estudados, 45 foram resistentes à meticilina. Observamos que para algumas cepas de MRSA os testes de triagem em ágar com 6μg/mL de oxacilina e difusão em meio sólido com oxacilina-1μg apresentaram dificuldades na sua interpretação. No entanto, todas as 45 amostras de MRSA, foram facilmente detectadas pelos testes com o disco de cefoxitina-30μg e pesquisa da PBP2a. A análise molecular das cepas de MRSA mostrou 8 padrões distintos de PFGE (A-H), com predominância do padrão A (73%), relacionado ao CEB. Estas carreavam o SCCmec tipo IIIA, e apresentaram uma considerável variedade de subtipos (A1-A16). Cinco cepas de MRSA portando SCCmec IV também foram xiv identificadas, três delas relacionadas geneticamente ao clone USA800 (Padrão B). Destas cinco, três (2 padrão F e 1 padrão B) foram altamente susceptíveis as drogas testadas, entretanto, dois outros isolados, padrão B, apresentaram multirresistência. As amostras restantes pertenciam a padrões de PFGE distintos dos clones internacionais predominantes em nosso continente. Para realização deste projeto de pesquisa, a metodologia exigiu a interação com pesquisadores de áreas como: infectologia, microbiologia e biologia molecular. Portanto, esta dissertação apresentou um caráter de multidisciplinaridade e transdiciplinaridade no seu desenvolvimento

Desenvolvimento e caracterização de um sistema microemulsionado contendo anfotericina b para uso oftalmológico

Universidade Federal do Rio Grande do Norte