Characterisation of sugarcane juice particles that influence the clarification process

Problems associated with processing whole sugarcane crop can be minimised by removing impurities during the clarification stage. As a first step, it is important to understand the colloidal chemistry of juice particles on a molecular level to assist development strategies for effective clarification performance. This paper presents the composition and surface characteristics of colloidal particles originating from various juice types by using scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), X-ray photoelectron spectroscopy (XPS) and zeta potential measurements. The composition and surface characteristics of colloidal juice particles are reported. The results indicate that there are three types of colloidal particles present viz., an aluminosilicate compound, silica and iron oxide, with the latter two being abundant. Proteins, polysaccharides and organic acids were identified on the surface of particles in juice. The overall particle charge varies from –2 mV to –6 mV. In comparison to juice expressed from burnt cane, the zeta potential values were more negative with juice particles originating from whole crop. This in part explains why these juices are difficult to clarify.

Phenolics in sugar cane juice : potential degradation by hydrogen peroxide and Fenton's reagent

The presence of colour in raw sugar plays a key role in the marketing strategy of the Australian raw sugar industry. Some sugars are relatively difficult to decolourise during refining and develop colour during storage. A new approach that might result in efficient and cost-effective colour removal during the sugar manufacturing process is the use of an advanced oxidation process (AOP), known as Fenton oxidation, that is, catalytic production of hydroxyl radicals from the decomposition of hydrogen peroxide using ferrous iron. As a first step towards developing this technology, this study determined the composition of colour precursors present in the juice of cane harvested by three different methods. The methods were harvesting cane after burning, harvesting the whole crop with half of the trash extracted and harvesting the whole crop with no trash extracted. The study also investigated the degradation at pH 3, 4 and 5 of a phenolic compound, caffeic acid (3,4–dihydroxycinnamic acid), which is present in sugar cane juice, using both hydrogen peroxide and Fenton’s reagent. The results show that juice expressed from whole crop cane has significantly higher colour than juices expressed from burnt cane. However, the concentrations of phenolic acids were lower in the juices expressed from whole crop cane. The main phenolic acids present in these juices were p-coumaric, vanillic, 2,3–dihydroxybenzoic, gallic and 3,4–dihydroxybenzoic acids. The degradation of caffeic acid significantly improved using Fenton’s reagent in comparison to hydrogen peroxide alone. The Fenton oxidation was optimum at pH 5 when up to ~86 % of caffeic acid degraded within 5 min.

Optimisation of process parameters for the removal of hydroxycinnamic acids in sugar solutions

Colour is one of the most important parameters in sugar quality and its presence in raw sugar plays a key role in the marketing strategy of sugar industries worldwide. This study investigated the degradation of a mixture of colour precursors using the Fenton oxidation process. These colour precursors are caffeic acid, p–coumaric acid and ferulic acid, which are present in cane juice. Results showed that with a Fe(II) to H2O2 molar ratio of 1:15 in an aqueous system at 25 °C, 77% of the total phenolic acid content was removed at pH 4.72. However, in a synthetic juice solution which contained 13 mass % sucrose (35 °C, pH 5.4), only 60% of the total phenolic acid content was removed.

Resources to assist research student supervision

This document is an adaptation of a report submitted to the ALTC in 2009, with additional data collected through subsequent interviews. The organisation of the contents also reflects a development of thought since the original project. The framework presented in this document is intended to provide supervisors with a range of options with respect to supervisory pedagogy. It has been developed to highlight different aspects of thinking about supervision as a teaching and learning practice; as well as approaches, strategies and roles associated with supervision. It will enable supervisors to become aware of the diverse options available to them and provide systematic ways of thinking about supervisory practices. Use of this framework will encourage supervisors to make choices based on broader, rather than more limited, repertoires. It will also encourage thinking about supervision as a teaching and learning practice.

A mill design concept for reducing bagasse moisture

This paper describes the development and testing of a novel mill design to reduce the moisture content of bagasse. It takes advantage of gravity to separate juice from bagasse by pushing bagasse upwards while juice drains downwards under gravity. The potential of the design to reduce bagasse moisture content has not been adequately established. The prototype mill had limited power available that prevented typical delivery nip compactions from being achieved. Tests conducted did show a reduction in bagasse moisture but that moisture reduction is less than expected under ideal conditions. Work on the mill design has ceased, at least for the foreseeable future. The design does have potential to reduce bagasse moisture content but presents some engineering challenges to establish a reliable, low maintenance design alternative.

Informed learning in online environments : supporting the higher education curriculum beyond Web 2.0

As boundaries between physical and online learning spaces become increasingly blurred in higher education, how can students gain full benefit of Web 2.0 social media and mobile technologies for learning? How can we, as information professionals and educators, best support the information literacy learning needs of students who are universally mobile and Google-focused? This chapter presents informed learning (Bruce, 2008) as a pedagogical construct with potential to support learning across the higher education curriculum, for Web 2.0 and beyond. After outlining the principles of informed learning and how they may enrich the higher education curriculum, we explain the role of library and information professionals in promoting informed learning for Web 2.0 and beyond. Then, by way of illustration, we describe recent experience at an American university where librarians simultaneously learned about and applied informed learning principles in reshaping the information literacy program.

Informed cyberlearning : a case study

This cyberlearning case study demonstrates the application of Web 2.0 in mainstream higher education curriculum, whilst providing an in-practice example of informed learning (Bruce, 2008. The case study features the learning experiences and creative outcomes of postgraduate Cyberlearning students at Queensland University of Technology in 2011. As informed learners, the students learned simultaneously about the theory and practice of Cyberlearning by carrying out a virtual team project. This involved collaboratively researching a topical issue, as well as exploring and applying Web 2.0 media. To support the informed learning of their peers, they created online resources which both convey disciplinary knowledge and showcase the educational potential of Web 2.0.

A preliminary study into the environmental and economic consequences of a sugar factory depithing operation

Bagasse stockpile operations have the potential to lead to adverse environmental and social impacts. Dust releases can cause occupational health and safety concerns for factory workers and dust emissions impact on the surrounding community. Preliminary modelling showed that bagasse depithing would likely reduce the environmental risks, particularly dust emissions, associated with large scale bagasse stockpiling operations. Dust emission properties were measured and used for dispersion modelling with favourable outcomes. Modelling showed a 70% reduction in peak ground level concentrations of PM10 dust (particles with an aerodynamic diameter less than 10 µm) from operations on depithed bagasse stockpiles compared to similar operations on stockpiles of whole bagasse. However, the costs of a depithing operation at a sugar factory were estimated to be approximately $2.1 million in capital expenditure to process 100,000 t/y of bagasse and operating costs were approximately $200,000 p.a. The total capital cost for a 10,000 t/y operation was approximately $1.6 million. The cost of depithing based on a discounted cash flow analysis was $5.50 per tonne of bagasse for the 100,000 t/y scenario. This may make depithing prohibitively expensive in many situations if installed exclusively as a dust control measure.

Moisture uptake and tensile properties of starch-sugar cane fibre films

THERE is an increasing need for biodegradable plastics because they are environmentally friendly and can replace petroleum-based non-degradable plastics which pollute the environment. Starch-derived films reinforced with sugar cane bagasse fibre, which are biodegradable, have been prepared and characterised by gravimetric analysis for moisture uptake, X-ray powder diffraction for crystallinity, and tensile testing for mechanical properties. Results have shown that the addition of bagasse fibre (5 wt%, 10 wt% or 20 wt%) to either (modified) potato starch (Soluble starch) or hydroxypropylated maize starch reduced moisture uptake by up to 30% at 58% relative humidity (RH). Also, the tensile strength and the Young’s Modulus increased up to 63% and 80% respectively, with the maximum value obtained with 5 wt% fibre at 58% RH. However, the tensile strain of the films significantly decreased by up to 84%. The results have been explained based on the crystallinity of the films and the intrinsic properties of starch and bagasse fibres.

Performing design analysis: game design creativity and the theatre of the impressed

We report and reflect upon the early stages of a research project that endeavours to establish a culture of critical design thinking in a tertiary game design course. We first discuss the current state of the Australian game industry and consider some perceived issues in game design courses and graduate outcomes. The second sec-tion presents our response to these issues: a project in progress which uses techniques originally exploited by Augusto Boal in his work, Theatre of the Oppressed. We appropriate Boal’s method to promote critical design thinking in a games design class. Finally, we reflect on the project and the ontology of design thinking from the perspective of Bruce Archer’s call to reframe design as a ‘third academic art’.

Addressing quality teaching in hard to staff settings : the Exceptional Teachers for Disadvantaged Schools Project

This Exceptional Teachers for Disadvantaged Schools (ETDS) project sets out to design a new model of Australian teacher education responding to recent demands for quality education in low SES and disadvantaged schools. The project moves teacher education from the ‘missionary’ (Larabee, 2010) or deficit (Comber and Kamler 2004; Flessa, 2007) approaches, towards a focus on notions of quality and academic excellence. Rice (2008, p.1) argues for a need to place more of the “very best teachers into the most challenging schools”, yet the problem is not merely one of training more teachers, for disadvantaged schools already receive disproportionate numbers of beginning teachers (Connell, 1994; Vickers & Ferfolja, 2006). Rather, Grossman and Loeb (2010, p. 245) argue the problem centers on the common practice of “[p]lacing the least experienced teachers with the most needy students”. This paper reports on the first year trial of the project. The ETDS project is at present, the only mainstream Australian teacher education model that targets cohorts of academically high achieving pre-service teachers with the overt aim of preparing graduates of the program to teach in disadvantaged schools. At the end of its first year, the ETDS program graduated 20 new teachers, each of whom had over the previous 18 months engaged with a specialized curriculum and carefully monitored/scaffolded practicum placements in disadvantaged schools around Brisbane, Australia.

An enhanced mill extraction model

An enhanced mill extraction model has been developed to calculate mill performance parameters and to predict the extraction performance of a milling unit. The model takes into account the fibre suspended in juice streams and calculates filling ratio, reabsorption factor, imbibition coefficient, and separation efficiency using more complete definitions than those used in previous extraction models. A mass balance model is used to determine the fibre, brix and moisture mass flows between milling units so that a complete milling train, including the return stream from the juice screen, is modelled. Model solutions are presented to determine the effect of different levels of fibre in juice and efficiency of fibre separation in the juice screen on brix extraction. The model provides more accurate results than earlier models leading to better understanding and improvement of the milling process.

A new approach to automatically producing schedules for cane railways

The scheduling of locomotive movements on cane railways has proven to be a very complex task. Various optimisation methods have been used over the years to try and produce an optimised schedule that eliminates or minimises bin supply delays to harvesters and the factory, while minimising the number of locomotives, locomotive shifts and cane bins, and also the cane age. This paper reports on a new attempt to develop an automatic scheduler using a mathematical model solved using mixed integer programming and constraint programming approaches and blocking parallel job shop scheduling fundamentals. The model solution has been explored using conventional constraint programming search techniques and found to produce a reasonable schedule for small-scale problems with up to nine harvesters. While more effort is required to complete the development of the full model with metaheuristic search techniques, the work completed to date gives confidence that the metaheuristic techniques will provide near optimal solutions in reasonable time.

The effect of mill orientation angle on bagasse moisture content

THIS PAPER DESCRIBES an experimental investigation to explore a concept designed to reduce the moisture content of bagasse. It takes advantage of gravity to separate juice from bagasse by feeding bagasse upwards into the nip of the mill while juice drains downwards under gravity. The investigation found that orienting the feed to a mill upwards does reduce bagasse moisture content and that the benefit is expected to be greater than two units of moisture. While an advantage was found in orienting the feed up to 50° above the horizontal, no extra benefit was found in increasing the angle higher (up to 60° was explored) and so a 50° orientation was identified as the preferred angle for this design concept.

Mixing and drying mud and ash at Tully Mill

Disposal of mud and ash, particularly in wet weather conditions, is a significant expense for mills. This paper reports on part of a process to pelletise mud and ash, aimed at making mud and ash more attractive to growers across entire mill districts. The full process and the re-constituting and centrifuging rotary vacuum filter mud part of the process were described in two papers to the 2011 conference. The component described in this paper involves aspects of mixing mud and ash with subsequent drying using boiler exit gas. The mud material needs to mix easily with boiler ash and the mixture has to feed easily into and be pneumatically conveyed by a flue gas dryer. The performance of a pilot flue gas dryer for drying mud and ash was evaluated. The mud and ash mixture was found to dry much faster than final bagasse, provided the mud and ash material was broken up into individual particles. A previously developed computer model of bagasse drying was updated to take into account the smaller particle size of the mud and ash mixture. This upgraded model predicted the performance of the pilot flue gas dryer well.