Recovery and refining of manganese as by-product from hydrometallurgical processes

The consumption of manganese is increasing, but huge amounts of manganese still end up in waste in hydrometallurgical processes. The recovery of manganese from multi-metal solutions at low concentrations may not be economical. In addition, poor iron control typically prevents the production of high purity manganese. Separation of iron from manganese can be done with chemical precipitation or solvent extraction methods. Combined carbonate precipitation with air oxidation is a feasible method to separate iron and manganese due to the fast kinetics, good controllability and economical reagents. In addition the leaching of manganese carbonate is easier and less acid consuming than that of hydroxide or sulfide precipitates. Selective iron removal with great efficiency from MnSO4 solution is achieved by combined oxygen or air oxidation and CaCO3 precipitation at pH > 5.8 and at a redox potential of > 200 mV. In order to avoid gypsum formation, soda ash should be used instead of limestone. In such case, however, extra attention needs to be paid on the reagents mole ratios in order to avoid manganese coprecipitation. After iron removal, pure MnSO4 solution was obtained by solvent extraction using organophosphorus reagents, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and bis(2,4,4- trimethylpentyl)phosphinic acid (CYANEX 272). The Mn/Ca and Mn/Mg selectivities can be increased by decreasing the temperature from the commonly used temperatures (40 –60oC) to 5oC. The extraction order of D2EHPA (Ca before Mn) at low temperature remains unchanged but the lowering of temperature causes an increase in viscosity and slower phase separation. Of these regents, CYANEX 272 is selective for Mn over Ca and, therefore, it would be the better choice if there is Ca present in solution. A three-stage Mn extraction followed by a two-stage scrubbing and two-stage sulfuric acid stripping is an effective method of producing a very pure MnSO4 intermediate solution for further processing. From the intermediate MnSO4 some special Mn- products for ion exchange applications were synthesized and studied. Three types of octahedrally coordinated manganese oxide materials as an alternative final product for manganese were chosen for synthesis: layer structured Nabirnessite, tunnel structured Mg-todorokite and K-kryptomelane. As an alternative source of pure MnSO4 intermediate, kryptomelane was synthesized by using a synthetic hydrometallurgical tailings. The results show that the studied OMS materials adsorb selectively Cu, Ni, Cd and K in the presence of Ca and Mg. It was also found that the exchange rates were reasonably high due to the small particle dimensions. Materials are stable in the studied conditions and their maximum Cu uptake capacity was 1.3 mmol/g. Competitive uptake of metals and acid was studied using equilibrium, batch kinetic and fixed-bed measurements. The experimental data was correlated with a dynamic model, which also accounts for the dissolution of the framework manganese. Manganese oxide micro-crystals were also bound onto silica to prepare a composite material having a particle size large enough to be used in column separation experiments. The MnOx/SiO2 ratio was found to affect significantly the properties of the composite. The higher the ratio, the lower is the specific surface area, the pore volume and the pore size. On the other hand, higher amount of silica binder gives composites better mechanical properties. Birnesite and todorokite can be aggregated successfully with colloidal silica at pH 4 and with MnO2/SiO2 weight ratio of 0.7. The best gelation and drying temperature was 110oC and sufficiently strong composites were obtained by additional heat-treatment at 250oC for 2 h. The results show that silica–supported MnO2 materials can be utilized to separate copper from nickel and cadmium. The behavior of the composites can be explained reasonably well with the presented model and the parameters estimated from the data of the unsupported oxides. The metal uptake capacities of the prepared materials were quite small. For example, the final copper loading was 0.14 mmol/gMnO2. According to the results the special MnO2 materials are potential for a specific environmental application to uptake harmful metal ions.

Oil Transportation in the Gulf of Finland in 2020 and 2030

This study is part of the Minimizing risks of maritime oil transport by holistic safety strategies (MIMIC) project. The purpose of this study is to provide a current state analysis of oil transportation volumes in the Baltic Sea and to create scenarios for oil transportation in the Gulf of Finland for the years 2020 and 2030. Future scenarios and information about oil transportation will be utilized in the modelling of oil transportation risks, which will be carried out as part of the MIMIC project. Approximately 290 million tons of oil and oil products were transported in the Baltic Sea in 2009, of which 55% (160 million tons) via the Gulf of Finland. Oil transportation volumes in the Gulf of Finland have increased from 40 million to almost 160 million tonnes over the last ten years. In Russia and Estonia, oil transportation mainly consists of export transports of the Russian oil industry. In Finnish ports in the Gulf of Finland, the majority of oil traffic is concentrated to the port of Sköldvik, while the remainder mainly consists of different oil products for domestic use. Transit transports to/from Russia make up small volumes of oil transportation. The largest oil ports in the Gulf of Finland are Primorsk, Tallinn, St. Petersburg and Sköldvik. The basis for the scenarios for the years 2020 and 2030 is formed by national energy strategies, the EU`s climate and energy strategies as well other energy and transportation forecasts for the years 2020 and 2030. Three alternative scenarios were produced for both 2020 and 2030. The oil volumes are based on the expert estimates of nine specialists. The specialists gave three volumes for each scenario: the expected oil transport volumes, and the minimum and maximum volumes. Variations in the volumes between the scenarios are not large, but each scenario tends to have rather a large difference between the figures for minimum and maximum volumes. This variation between the minimum and maximum volumes ranges around 30 to 40 million tonnes depending on the scenario. On the basis of this study, no a dramatic increase in oil transportation volumes in the Gulf of Finland is to be expected. Most of the scenarios only forecasted a moderate growth in maritime oil transportation compared to the current levels. The effects of the European energy policy favouring renewable energy sources can be seen in the 2030 scenarios, in which the transported oil volumes are smaller than in the 2020 scenarios. In the Slow development 2020 scenario, oil transport volumes for 2020 are expected to be 170.6 Mt (million tonnes), in the Average development 2020 187.1 Mt and in the Strong development 2020 201.5 Mt. The corresponding oil volumes for the 2030 scenarios were 165 Mt for the Stagnating development 2030 scenario, 177.5 Mt for the Towards a greener society 2030 scenario and 169.5 Mt in the Decarbonising society 2030 scenario.

Antimicrobial activity and acute and chronic toxicity of the essential oil of Lippia origanoides

Currently, there is a growing interest in medicinal plants, because of an increased demand for alternate therapies. In this study, the antimicrobial activity and toxicity of the essential oil of Lippia origanoides (L. origanoides) were investigated. The essential oil of L. origanoides was extracted by steam-dragging distillation and its constituents were identified by chromatography coupled with mass spectrometry. Among the 15 compounds identified, the most abundant were carvacrol (29.00%), o-cymene (25.57%), and thymol methyl ether (11.50%). The essential oil was studied in antimicrobial assays to determine the MIC and MBC. The results indicated that a concentration of 120μL/mL of oil was sufficient to inhibit the growth of the following microorganisms: Escherichia coli (ATCC 25922), Staphylococcus aureus (ATCC 25923) and Salmonella cholerasuis (ATCC 10708). Acute and chronic toxic effects of orally administered oil were investigated in Wistar rats by using standard methods. Doses of 30, 60 and 120mg/kg of the essential oil did not induce significant changes in weight, behavior or hematological and biochemical parameters in the animals. There were no signs of any histopathological changes to the liver, kidneys or heart of the treated rats, suggesting that Lippia origanoides oil is non-toxic after oral administration in acute or chronic toxicity studies. The results obtained in this study show that the essential oil of L. origanoides has a high safety margin, with no detectable toxic effects in rats treated with doses to 120mg/kg. In addition, L. origanoides oil demonstrated potent antimicrobial activity against S. aureus, E. coli and S. cholerasuis. Based on these findings, this essential oil may have practical application as a veterinary antimicrobial.

Blackcurrant seed oil for prevention of atopic dermatitis

One hypothesis for the increased incidence of atopic diseases has been that it is associated with changing dietary habits, especially the changed intake of essential fatty acids (EFAs). The metabolism of EFAs produces eiconasoids, prostaglandins and leukotrienes, which are essential to organs and play a major role in regulation of inflammation and immune response. In some studies persons with atopic dermatitis have been found to have reduced levels of EFAs. The first year of infancy as well as the foetal period are crucial for the development of atopic immune response. The composition of blackcurrant seed oil (BCSO) corresponds to the recommended ratio of EFAs n-3 and n-6 in the diet (1/3-1/4) and as a dietary supplement could, even in small doses, modify the unbalance of EFAs in an efficient way. The purpose of this study was to find out whether atopic allergies can be prevented by supplementing the diet of pregnant mothers with blackcurrant seed oil and whether it could affect the immunological balance of a child. We also sought to find out whether a blackcurrant seed oil supplementation can affect the composition of breast milk to suppress the T helper 2 lymphocyte (Th2) responses in infants. 313 pregnant mothers were randomly assigned to receive BCSO (n=151) or olive oil as placebo (n=162). Supplementation was started at the 8th to 16th weeks of pregnancy, 6 capsules per day (dose of 3 g), and continued until the cessation of breastfeeding. It was thereafter followed by direct supplementation to infants of 1 ml (1 g) of oil per day until the age of two years. Atopic dermatitis and its severity (SCORAD index) were evaluated, serum total IgE was measured and skin prick tests were performed at the age of 3, 12 and 24 months. Peripheral blood mononuclear cell (PBMC) samples were taken at the age of 3 and 12 months and breast milk samples were collected during the first 3 months of breastfeeding. Parental atopy was common (81.7%) in the studied infants, making them infants with increased atopy risk. There was a significantly lower prevalence of atopic dermatitis in the BCSO group (33%) than in the olive oil group (47%) at the age of 12 months. Also, SCORAD was lower in the BCSO group than in the olive oil group. Dietary intervention with BCSO had immunomodulatory effects on breast milk, inducing cytokine production from Th2 to Th1 immunodeviation. It decreased the level of IL-4 and elevated the level of IFN-γ. BCSO intervention did not affect cytokines in the children’s PBMC. However, children of smoking parents in the combined BCSO and olive oil group had significantly elevated levels of Th2 type cytokines IL-4, IL-5 and the proinflammator cytokine TNF. Dietary supplementation with BCSO is safe. It is well tolerated and transiently reduces the prevalence of atopic dermatitis at the age of 12 months. It can possibly become a potential tool in prevention of atopic symptoms when used at the early stages of life.

Maximizing of water recovery in nanofiltration of mine process waters by using antiscalants

Reverse osmosis and nanofiltration are among the most effective and widely used desalination and water softening technologies. They can also be used to treat mining wastewaters and are capable of producing water of extremely high purity, regardless of the high concentrations of toxic heavy metals and extreme pH and salinity. However, challenges with recovering the salts and metals from mining wastewaters in exploitable form, as well as problems with scaling still limit the process efficiency and the ratio of purified water recoverable from process waters. To address the problem of membrane scaling caused by calcium sulfate, batch filtration experiments with the Desal-5 DL nanofiltration membrane, three commercial antiscalants and actual mine process water from a copper mine were performed. The aim of these experiments was to find process conditions where maximum water recovery would be achieved before significant scaling or irreversible membrane fouling would occur and to further improve water recovery by addition of antiscalants. Water recovery of 70 % was reached with the experimental setups by optimizing process conditions. PC-504T antiscaling agent was determined to be the most effective of the three antiscalants used and the addition of 5 ppm of PC-504T allowed the water recovery to be further increased from 70 % to 85 % before major scaling was observed. In these conditions 92 % calcium rejection was achieved.

An Update on Inter-Country Differences in Recovery and Utilization of Recycled Paper

The use of recovered paper as raw material in the paper and board industry has increased heavily during recent decades. At the same time, growing environmental awareness has raised the interest in recycling and a more sustainable way of living, at least in high-income countries. This paper combines these topics and explores how economic, demographic and environmental factors have affected the recovery and utilization of recycled paper between 1992 and 2010 in a sample of 70 countries. This study updates and extends the previous research on the topic using panel data and panel data estimation methods. The results confirm the roles of economic determinants but also indicate that concern for the environment impacts the recovery of recycled paper particularly in high-income countries. Moreover, the motives for recycling appear to depend on the income level of a country, which is something that future policies should consider.

Effect of neurotrophic factor, MDP, on rats’ nerve regeneration

Our objective was to determine the immune-modulating effects of the neurotrophic factor N-acetylmuramyl-L-alanyl-D-isoglutamine (MDP) on median nerve regeneration in rats. We used male Wistar rats (120-140 days of age, weighing 250-332 g) and compared the results of three different techniques of nerve repair: 1) epineural neurorrhaphy using sutures alone (group S - 10 rats), 2) epineural neurorrhaphy using sutures plus fibrin tissue adhesive (FTA; group SF - 20 rats), and 3) sutures plus FTA, with MDP added to the FTA (group SFM - 20 rats). Functional assessments using the grasp test were performed weekly for 12 weeks to identify recovery of flexor muscle function in the fingers secondary to median nerve regeneration. Histological analysis was also utilized. The total number and diameter of myelinated fibers were determined in each proximal and distal nerve segment. Two indices, reported as percentage, were calculated from these parameters, namely, the regeneration index and the diameter change index. By the 8th week, superiority of group SFM over group S became apparent in the grasping test (P = 0.005). By the 12th week, rats that had received MDP were superior in the grasping test compared to both group S (P < 0.001) and group SF (P = 0.001). Moreover, group SF was better in the grasping test than group S (P = 0.014). However, no significant differences between groups were identified by histological analysis. In the present study, rats that had received MDP obtained better function, in the absence of any significant histological differences.

Negative emotions affect postoperative scores for evaluating functional knee recovery and quality of life after total knee replacement

This study aimed to determine whether psychological factors affect health-related quality of life (HRQL) and recovery of knee function in total knee replacement (TKR) patients. A total of 119 TKR patients (male: 38; female: 81) completed the Beck Anxiety Inventory (BAI), Beck Depression Inventory (BDI), State Trait Anxiety Inventory (STAI), Eysenck Personality Questionnaire-revised (EPQR-S), Knee Society Score (KSS), and HRQL (SF-36). At 1 and 6 months after surgery, anxiety, depression, and KSS scores in TKR patients were significantly better compared with those preoperatively (P<0.05). SF-36 scores at the sixth month after surgery were significantly improved compared with preoperative scores (P<0.001). Preoperative Physical Component Summary Scale (PCS) and Mental Component Summary Scale (MCS) scores were negatively associated with extraversion (E score) (B=-0.986 and -0.967, respectively, both P<0.05). Postoperative PCS and State Anxiety Inventory (SAI) scores were negatively associated with neuroticism (N score; B=-0.137 and -0.991, respectively, both P<0.05). Postoperative MCS, SAI, Trait Anxiety Inventory (TAI), and BAI scores were also negatively associated with the N score (B=-0.367, -0.107, -0.281, and -0.851, respectively, all P<0.05). The KSS function score at the sixth month after surgery was negatively associated with TAI and N scores (B=-0.315 and -0.532, respectively, both P<0.05), but positively associated with the E score (B=0.215, P<0.05). The postoperative KSS joint score was positively associated with postoperative PCS (B=0.356, P<0.05). In conclusion, for TKR patients, the scores used for evaluating recovery of knee function and HRQL after 6 months are inversely associated with the presence of negative emotions.

THE EFFECTIVE DIFFUSIVITY OF CLOVE(Eugenia caryophyllus) ESSENTIAL OIL IN PRESSURIZED CO2

The effective diffusivity of clove essential oil in subcritical liquid CO2 was estimated. The experimental apparatus employed was a fixed-bed extractor. The fixed bed was formed with grounded (mesh -32 + 65) and compacted clove buds which were considered a solid element. The effective diffusion coefficient was evaluated by fitting the experimental concentration profile to the unsteady state mass balance equation for unidirectional diffusion in a finite solid medium. The diffusion coefficient was related to the concentration of oil in the solid by an exponential function. The estimated values of the effective diffusion coefficient varied from 3.64 to 5.22x10-10 m2/s. The average relative errors were lower than 3.1%.

Survey of aflatoxins in tomato products

Tomatoes are highly susceptible to fungi contamination in the field, during transportation, processing, and storage. Aspergillus flavus and Aspergillus parasiticus have been isolated from tomatoes and tomato products, and both fungi species can produce aflatoxin, mycotoxin with hepatotoxic, carcinogenic, teratogenic, and mutagenic effects on all animal species tested so far. In order to verify a possible aflatoxin contamination of tomato products commercialized in Brazil, 63 samples of tomato products (pulp, paste, purée, ketchup, dehydrated tomatoes, and dried tomatoes preserved in oil) produced in 5 Brazilian states and 1 imported sample (ketchup), totalizing 29 brands, were analyzed by thin layer chromatography. The analytical method showed an average recovery of 86% for all aflatoxins at two spiking levels. The limits of detection for the aflatoxins B1, B2, G1, and G2 varied with the type of the product ranging from 2 to 7 µg/kg. Aflatoxins were not detected in any evaluated sample indicating that they did not pose a risk to human health since there was no invasion of raw materials by toxigenic fungi or no conditions for toxin production.

Origanum vulgare L. essential oil as inhibitor of potentially toxigenic Aspergilli

Origanum vulgare L. essential oil has been known as an interesting source of antimicrobial compounds to be applied in food conservation. In this study, the effect of O. vulgare essential on the growth of A. flavus, A. parasiticus, A. fumigatus, A. terreus and A. ochraceus was assessed. The essential oil had a significant inhibitory effect on all assayed fungi. MIC was 0.6 µL.mL-1 for all fungi, while MFC was in the range of 1.25-2.5 µL.mL-1. The radial mycelial growth of A. flavus and A. parasiticus was strongly inhibited over 14 days at 0.6, 1.25 and 2.5 µL.mL-1 of oil in solid medium. The mycelial mass of all fungi was inhibited over 90% at 0.6 and 0.3 µL.mL-1 in liquid medium, while it was 100% at 1.25 µL.mL-1. The oil in a range of concentrations (0.6 to 2.5 µL.mL-1) was effective in inhibiting the viability and spores germination in a short time of exposure. The main morphological changes caused by the essential oil in A. parasiticus observed under light microscopy were absence of conidiation, leakage of cytoplasm, loss of pigmentation, and disrupted cell structure. These results demonstrated that O. vulgare essential oil produced a significant fungitoxic effect supporting its possible rational use as anti-mould compound in food conservation.

Inhibitory effect of the essential oil from Eugenia caryophyllata Thumb leaves on coalho cheese contaminating microorganisms

Coalho cheese (a firm but very lightweight cheese produced in Brazil) is widely produced and consumed in the Brazilian Northeast and its production has been mainly related to small farmers. This food has been frequently characterized as having high microbial load posing a risk for the health of consumers. This study aimed to indentify the chemical compounds of the essential oil from Eugenia caryophyllata leaves; to evaluate the inhibitory effect of the oil against coalho cheese contaminating microorganisms; and to assess its efficacy in inhibiting the autochthonous microflora of the cheese during refrigerated storage. Eugenol (74%) was found to be the most prevalent compound in the essential oil. Minimum Inhibitory Concentration (MIC) and Minimum Cidal Concentration (MCC) in laboratorial broth were in the range of 2.5-5 and 5-20 µg.mL-1, respectively. Vaccum packed coalho cheese added with 5, 10, and 20 µg.g-1 of oil showed a lower growth rate (like-static effect) against mesophilic bacteria during the time intervals evaluated. On the other hand, 2.5-10 µg.g-1 of oil provided a prominent decrease toward fungi count in cheese samples during storage. These results reveal the interesting antimicrobial property of the essential oil from E. caryophyllata leaves against a range of coalho cheese-related microorganisms in laboratorial media and in food matrix.

The role of metal ions in selective and sustainable processes

Sustainability and recycling are core values in today’s industrial operations. New materials, products and processes need to be designed in such a way as to consume fewer of the diminishing resources we have available and to put as little strain on the environment as possible. An integral part of this is cleaning and recycling. New processes are to be designed to improve the efficiency in this aspect. Wastewater, including municipal wastewaters, is treated in several steps including chemical and mechanical cleaning of waters. Well-cleaned water can be recycled and reused. Clean water for everyone is one of the greatest challenges we are facing today. Ferric sulphate, made by oxidation from ferrous sulphate, is used in water purification. The oxidation of ferrous sulphate, FeSO4, to ferric sulphate in acidic aqueous solutions of H2SO4 over finely dispersed active carbon particles was studied in a vigorously stirred batch reactor. Molecular oxygen was used as the oxidation agent and several catalysts were screened: active carbon, active carbon impregnated with Pt, Rh, Pd and Ru. Both active carbon and noble metal-active carbon catalysts enhanced the oxidation rate considerably. The order of the noble metals according to the effect was: Pt >> Rh > Pd, Ru. By the use of catalysts, the production capacities of existing oxidation units can be considerably increased. Good coagulants have a high charge on a long polymer chain effectively capturing dirty particles of the opposite charge. Analysis of the reaction product indicated that it is possible to obtain polymeric iron-based products with good coagulation properties. Systematic kinetic experiments were carried out at the temperature and pressure ranges of 60B100°C and 4B10 bar, respectively. The results revealed that both non-catalytic and catalytic oxidation of Fe2+ to Fe3+ take place simultaneously. The experimental data were fitted to rate equations, which were based on a plausible reaction mechanism: adsorption of dissolved oxygen on active carbon, electron transfer from Fe2+ ions to adsorbed oxygen and formation of surface hydroxyls. A comparison of the Fe2+ concentrations predicted by the kinetic model with the experimentally observed concentrations indicated that the mechanistic rate equations were able to describe the intrinsic oxidation kinetics of Fe2+ over active carbon and active carbon-noble metal catalysts. Engineering aspects were closely considered and effort was directed to utilizing existing equipment in the production of the new coagulant. Ferrous sulphate can be catalytically oxidized to produce a novel long-chained polymeric iron-based flocculent in an easy and affordable way in existing facilities. The results can be used for modelling the reactors and for scale-up. Ferric iron (Fe3+) was successfully applied for the dissolution of sphalerite. Sphalerite contains indium, gallium and germanium, among others, and the application can promote their recovery. The understanding of the reduction process of ferric to ferrous iron can be used to develop further the understanding of the dissolution mechanisms and oxidation of ferrous sulphate. Indium, gallium and germanium face an ever-increasing demand in the electronics industry, among others. The supply is, however, very limited. The fact that most part of the material is obtained through secondary production means that real production quota depends on the primary material production. This also sets the pricing. The primary production material is in most cases zinc and aluminium. Recycling of scrap material and the utilization of industrial waste, containing indium, gallium and geranium, is a necessity without real options. As a part of this study plausible methods for the recovery of indium, gallium and germanium have been studied. The results were encouraging and provided information about the precipitation of these valuables from highly acidic solutions. Indium and gallium were separated from acidic sulphuric acid solutions by precipitation with basic sulphates such as alunite or they were precipitated as basic sulphates of their own as galliunite and indiunite. Germanium may precipitate as a basic sulphate of a mixed composition. The precipitation is rapid and the selectivity is good. When the solutions contain both indium and gallium then the results show that gallium should be separated before indium to achieve a better selectivity. Germanium was separated from highly acidic sulphuric acid solutions containing other metals as well by precipitating with tannic acid. This is a highly selective method. According to the study other commonly found metals in the solution do not affect germanium precipitation. The reduction of ferric iron to ferrous, the precipitation of indium, gallium and germanium, and the dissolution of the raw materials are strongly depending on temperature and pH. The temperature and pH effect were studied and which contributed to the understanding and design of the different process steps. Increased temperature and reduced pH improve the reduction rate. Finally, the gained understanding in the studied areas can be employed to develop better industrial processes not only on a large scale but also increasingly on a smaller scale. The small amounts of indium, gallium and germanium may favour smaller and more locally bound recovery.

Preoperative education and its influence on perception of recovery for clients awaiting total hip and total knee replacement surgery /

The puqjose of this study was to examine the manner in which an inviting approach to a preoperative teaching and learning educational experience influenced the perception and subsequent recovery of clients who were awaiting total hip and total knee replacement surgery. An in-depth review of the internal and external factors that shape client perceptions was undertaken in this study. In addition, this study also explored whether or not the Prehab Program was preparing clients physically, socially, and psychologically for surgery. Data for this qualitative case study research were collected through preoperative interviews with 4 participants awaiting total hip replacement surgery and 1 participant awaiting total knee replacement surgery. Four postoperative interviews were conducted with the participants who had received total hip replacement surgery. The occupational therapist and physical therapist who were the coleaders of the Prehab Program at the time of this study were also interviewed. The results of this study suggest that while individuals may receive similar educational experiences, their perceptions of the manner in which they benefited from these experiences varied. This is illustrated in the research findings, which concluded that while clients benefited physically from the inviting approach used during the practical teaching session, not all clients perceived the psychological benefits of this practice session, especially clients with preexisting high levels of anxiety. In addition to increasing the understanding of the internal as well as external factors that influence the perceptions of clients, this study has also served as an opportunity for reflection on practice for the Prehab therapists and other healthcare educators.

The Alberta Dilemma: Optimal Sharing of a Water Resource by an Agricultural and an Oil Sector

The purpose of this paper is to characterize the optimal time paths of production and water usage by an agricultural and an oil sector that have to share a limited water resource. We show that for any given water stock, if the oil stock is sufficiently large, it will become optimal to have a phase during which the agricultural sector is inactive. This may mean having an initial phase during which the two sectors are active, then a phase during which the water is reserved for the oil sector and the agricultural sector is inactive, followed by a phase during which both sectors are active again. The agricultural sector will always be active in the end as the oil stock is depleted and the demand for water from the oil sector decreases. In the case where agriculture is not constrained by the given natural inflow of water once there is no more oil, we show that oil extraction will always end with a phase during which oil production follows a pure Hotelling path, with the implicit price of oil net of extraction cost growing at the rate of interest. If the natural inflow of water does constitute a constraint for agriculture, then oil production never follows a pure Hotelling path, because its full marginal cost must always reflect not only the imputed rent on the finite oil stock, but also the positive opportunity cost of water.