Interleaved PC-OFDM to reduce peak-to-average power ratio

Parallel combinatory orthogonal frequency division multiplexing (PC-OFDM yields lower maximum peak-to-average power ratio (PAR), high bandwidth efficiency and lower bit error rate (BER) on Gaussian channels compared to OFDM systems. However, PC-OFDM does not improve the statistics of PAR significantly. In this chapter, the use of a set of fixed permutations to improve the statistics of the PAR of a PC-OFDM signal is presented. For this technique, interleavers are used to produce K-1 permuted sequences from the same information sequence. The sequence with the lowest PAR, among K sequences is chosen for the transmission. The PAR of a PC-OFDM signal can be further reduced by 3-4 dB by this technique. Mathematical expressions for the complementary cumulative density function (CCDF)of PAR of PC-OFDM signal and interleaved PC-OFDM signal are also presented.

Information sharing in the 21st century : progress and challenges

With the increasing threat of cyber and other attacks on critical infrastructure, governments throughout the world have been organizing industry to share information on possible threats. In Australia the Office of the Attorney General has formed Trusted Information Sharing Networks (TISN) for the various critical industries such as banking and electricity. Currently the majority of information for a TISN is shared at physical meetings. To meet cyber threats there are clearly limitations to physical meetings. Many of these limitations can be overcome by the creation of a virtual information sharing network (VISN). However there are many challenges to overcome in the design of a VISN both from a policy and technical viewpoint. We shall discuss some of these challenges in this talk.

Stretch : episodes of a recreation in progress

An episodic recreation of Hibberd's Stretch of the Imagination presented as a performance extract as part of the Enter the New Wave Symposium at Melbourne University September 2007.

Sustainable infrastructure project planning : progress in contemporary decision support tools

Most infrastructure project developments are complex in nature, particularly in the planning phase. During this stage, many vague alternatives are tabled - from the strategic to operational level. Human judgement and decision making are characterised by biases, errors and the use of heuristics. These factors are intangible and hard to measure because they are subjective and qualitative in nature. The problem with human judgement becomes more complex when a group of people are involved. The variety of different stakeholders may cause conflict due to differences in personal judgements. Hence, the available alternatives increase the complexities of the decision making process. Therefore, it is desirable to find ways of enhancing the efficiency of decision making to avoid misunderstandings and conflict within organisations. As a result, numerous attempts have been made to solve problems in this area by leveraging technologies such as decision support systems. However, most construction project management decision support systems only concentrate on model development and neglect fundamentals of computing such as requirement engineering, data communication, data management and human centred computing. Thus, decision support systems are complicated and are less efficient in supporting the decision making of project team members. It is desirable for decision support systems to be simpler, to provide a better collaborative platform, to allow for efficient data manipulation, and to adequately reflect user needs. In this chapter, a framework for a more desirable decision support system environment is presented. Some key issues related to decision support system implementation are also described.

Charity law reforms : overview of progress since 2001

In the UK, Singapore, Canada, New Zealand and Australia, as in many other jurisdictions, charity law is rooted in the common law and anchored on the Statute of Charitable Uses 1601. The Pemsel classification of charitable purposes was uniformly accepted, and together with a shared and growing pool of judicial precedents, aided by the ‘spirit and intendment’ rule, has subsequently allowed the law to develop along much the same lines. In recent years, all the above jurisdictions have embarked on law reform processes designed to strengthen regulatory processes and to statutorily define and encode common law concepts. The reform outcomes are now to be found in a batch of national charity statutes which reflect interesting differences in the extent to which their respective governments have been prepared to balance the modernising of charitable purposes and other common law concepts alongside the customary concern to tighten the regulatory framework.

Enhancing agrobacterium-mediated transformation efficiency of sugarcane : progress towards an efficient, genotype-independent method

Several key issues need to be resolved before an efficient and reproducible Agrobacterium-mediated sugarcane transformation method can be developed for a wider range of sugarcane cultivars. These include loss of morphogenetic potential in sugarcane cells after Agrobacterium-mediated transformation, effect of exposure to abiotic stresses during in vitro selection, and most importantly the hypersensitive cell death response of sugarcane (and other nonhost plants) to Agrobacterium tumefaciens. Eight sugarcane cultivars (Q117, Q151, Q177, Q200, Q208, KQ228, QS94-2329, and QS94-2174) were evaluated for loss of morphogenetic potential in response to the age of the culture, exposure to Agrobacterium strains, and exposure to abiotic stresses during selection. Corresponding changes in the polyamine profiles of these cultures were also assessed. Strategies were then designed to minimize the negative effects of these factors on the cell survival and callus proliferation following Agrobacterium-mediated transformation. Some of these strategies, including the use of cell death protector genes and regulation of intracellular polyamine levels, will be discussed.

Models of collective cell spreading with variable cell aspect ratio : a motivation for degenerate diffusion models

Continuum diffusion models are often used to represent the collective motion of cell populations. Most previous studies have simply used linear diffusion to represent collective cell spreading, while others found that degenerate nonlinear diffusion provides a better match to experimental cell density profiles. In the cell modeling literature there is no guidance available with regard to which approach is more appropriate for representing the spreading of cell populations. Furthermore, there is no knowledge of particular experimental measurements that can be made to distinguish between situations where these two models are appropriate. Here we provide a link between individual-based and continuum models using a multi-scale approach in which we analyze the collective motion of a population of interacting agents in a generalized lattice-based exclusion process. For round agents that occupy a single lattice site, we find that the relevant continuum description of the system is a linear diffusion equation, whereas for elongated rod-shaped agents that occupy L adjacent lattice sites we find that the relevant continuum description is connected to the porous media equation (pme). The exponent in the nonlinear diffusivity function is related to the aspect ratio of the agents. Our work provides a physical connection between modeling collective cell spreading and the use of either the linear diffusion equation or the pme to represent cell density profiles. Results suggest that when using continuum models to represent cell population spreading, we should take care to account for variations in the cell aspect ratio because different aspect ratios lead to different continuum models.

Assessing and learning in internships: Reflecting on pedagogy and progress

An elective internship unit as part of a work integrated learning program in a business faculty is presented as a case study. In the unit, students complete a minimum of 120 hours work placement over the course of a 13 week semester. The students are majoring in advertising, marketing, or public relations and are placed in corporations, government agencies, and not for profit organisations. To support and scaffold the students’ learning in the work environment, a range of classroom and online learning activities are part of the unit. Classroom activities include an introductory workshop to prepare students for placement, an industry panel, and interview workshop. These are delivered as three workshops across the semester. Prior to commencing their placement, students complete a suite of online learning modules. The Work Placement Preparation Program assists students in securing obtaining a placement and make a successful transition to the work environment. It provides an opportunity for students to source possible work placement sites, prepare competitive applications, develop and rehearse interview skills, deal with workplace issues, and use a student ePortfolio to reflect on their skills and achievements. Students contribute to a reflective blog throughout their placement, with feedback from academic supervisors throughout the placement. The completion of the online learning modules and contribution to a reflective blog are assessed as part of the unit. Other assessment tools include a internship plan and learning contract between the student, industry supervisor, and academic supervisor; job application including responses to selection criteria; and presentation to peers, academics and industry representatives at a poster session. The paper discusses the development of the internship unit over three years, particularly learning activities and assessment. The reflection and refinement of the unit is informed by a pedagogical framework, and the development of processes to best manage placement for all stakeholders. A model of best practice is proposed, that can be adapted to a variety of discipline areas.

Review of the progress in thin bed technology for masonry construction

Thin bed technology for clay/ concrete masonry is gaining popularity in many parts of the developed economy in recent times through active engagement of the industry with the academia. One of the main drivers for the development of thin bed technology is the progressive contraction of the professional brick and block laying workforce as the younger generation is not attracted towards this profession due to the general perception of the society towards manual work as being outdated in the modern digital economy. This situation has led to soaring cost of skilled labour associated with the general delay in completion of construction activities in recent times. In parallel, the advent of manufacturing technologies in producing bricks and blocks with adherence to specified dimensions and shapes and several rapid setting binders are other factors that have contributed to the development of thin bed technology. Although this technology is still emerging, especially for applications to earthquake prone regions, field applications are reported in Germany for over a few decades and in Italy since early 2000. The Australian concrete masonry industry has recently taken keen interest in pursuing research with a view to developing this technology. This paper presents the background information including review of literature and pilot studies that have been carried out to enable planning of the development of thin bed technology. The paper concludes with recommendations for future research.

Monitoring children's progress using child portfolios

Introduces a method to early childhood professionals of observing children as they are involved in everyday play episodes, record children's development and plan for this, while utilising the knowledge and input of the key players in the partnership, parents and teachers.