Atuação do fisioterapeuta dermatofuncional e seu reconhecimento pelos profissionais de saúde da região de Lisboa

Mestrado em Fisioterapia

Strength prediction and experimental validation of adhesive joints including polyethylene, carbon-epoxy and aluminium adherends

Polyolefins are especially difficult to bond due to their non-polar, non-porous and chemically inert surfaces. Acrylic adhesives used in industry are particularly suited to bond these materials, including many grades of polypropylene (PP) and polyethylene (PE), without special surface preparation. In this work, the tensile strength of single-lap PE and mixed joints bonded with an acrylic adhesive was investigated. The mixed joints included PE with aluminium (AL) or carbon fibre reinforced plastic (CFRP) substrates. The PE substrates were only cleaned with isopropanol, which assured cohesive failures. For the PE CFRP joints, three different surfaces preparations were employed for the CFRP substrates: cleaning with acetone, abrasion with 100 grit sand paper and peel-ply finishing. In the PE AL joints, the AL bonding surfaces were prepared by the following methods: cleaning with acetone, abrasion with 180 and 320 grit sand papers, grit blasting and chemical etching with chromic acid. After abrasion of the CFRP and AL substrates, the surfaces were always cleaned with acetone. The tensile strengths were compared with numerical results from ABAQUS® and a mixed mode (I+II) cohesive damage model. A good agreement was found between the experimental and numerical results, except for the PE AL joints, since the AL surface treatments were not found to be effective.

Interlaminar fracture characterization of a carbon-epoxy composite in pure mode II

The interlaminar fracture toughness in pure mode II (GIIc) of a Carbon-Fibre Reinforced Plastic (CFRP) composite is characterized experimentally and numerically in this work, using the End-Notched Flexure (ENF) fracture characterization test. The value of GIIc was extracted by a new data reduction scheme avoiding the crack length measurement, named Compliance-Based Beam Method (CBBM). This method eliminates the crack measurement errors, which can be non-negligible, and reflect on the accuracy of the fracture energy calculations. Moreover, it accounts for the Fracture Process Zone (FPZ) effects. A numerical study using the Finite Element Method (FEM) and a triangular cohesive damage model, implemented within interface finite elements and based on the indirect use of Fracture Mechanics, was performed to evaluate the suitability of the CBBM to obtain GIIc. This was performed comparing the input values of GIIc in the numerical models with the ones resulting from the application of the CBBM to the numerical load-displacement (P-) curve. In this numerical study, the Compliance Calibration Method (CCM) was also used to extract GIIc, for comparison purposes.

Taper angle optimization of scarf repairs in carbon-epoxy laminates

The increasing use of Carbon-Fibre Reinforced Plastic (CFRP) laminates in high responsibility applications introduces an issue regarding their handling after damage. The availability of efficient repair methods is essential to restore the strength of the structure. The availability of accurate predictive tools for the repairs behaviour is also essential for the reduction of costs and time associated to extensive tests. This work reports on a numerical study of the tensile behaviour of three-dimensional (3D) adhesively-bonded scarf repairs in CFRP structures, using a ductile adhesive. The Finite Element (FE) analysis was performed in ABAQUS® and Cohesive Zone Models (CZM’s) was used for the simulation of damage in the adhesive layer. A parametric study was performed on two geometric parameters. The use of overlaminating plies covering the repaired region at the outer or both repair surfaces was also tested as an attempt to increase the repairs efficiency. The results allowed the proposal of design principles for repairing CFRP structures.

Intrusion of Lamprophyre dyke and related deformation effects in the host rock salt: A case study from the Loulé Diapir, Portugal

A rock salt-lamprophyre dyke contact zone (sub-vertical, NE-SW strike) was investigated for its petrographic, mechanic and physical properties by means of anisotropy of magnetic susceptibility CAMS) and rock magnetic properties, coupled with quantitative microstructural analysis and thermal mathematical modelling. The quantitative microstructural analysis of halite texture and solid inclusions revealed good spatial correlation with AMS and halite fabrics. The fabrics of both lamprophyre and rock salt record the magmatic intrusion, "plastic" flow and regional deformation (characterized by a NW-SE trending steep foliation). AMS and microstructural analysis revealed two deformation fabrics in the rock salt: (1) the deformation fabrics in rock salt on the NW side of the dyke are associated with high temperature and high fluid activity attributed to the dyke emplacement; (2) On the opposite side of the dyke, the emplacement-related fabric is reworked by localized tectonic deformation. The paleomagnetic results suggest significant rotation of the whole dyke, probably during the diapir ascent and/or the regional Tertiary to Quaternary deformation. (C) 2014 Elsevier B.V. All rights reserved.

TiB2 nanostructured coating for GFRP injection moulds

In the injection moulding of polypropylene reinforced with hard glass fibres, die materials are commonly subjected to severe abrasive wear. In order to improve its wear resistance, an unbalanced magnetron sputtering PVD compositional monolayered coating has been produced. The film was composed by a nanostructured TiB2 monolayer. Microstructure characterization and thickness evaluation were conducted by scanning electron microscopy (SEM). Film topography and roughness were accessed by SEM and Atomic Force Microscopy (AFM). The phase analyse was investigated by X-ray diffraction (XRD), using Cu Kalpha radiation. Scratch tests were conducted in order to study the film adhesion to the substrate. Load-Displacement curves (nanoindentation analysis) allowed measuring the film hardness and Young's modulus. A ball-cratering tribometer was used to determine the micro-abrasion laboratorial wear resistance, under different tests conditions, using SiC particles in distilled water slurry. At the end of these tests, the worn surfaces were analyzed by SEM and Energy Dispersive X-ray Spectroscopy (EDS) in order to compare these results with some other coatings already tested in the same conditions. To test the practical wear resistance, 135000 injection cycles were done in a plastic injection industrial mould. Coated samples were put on the plastic feed canal, after a turbulent zone. In these tests, a 30% (wt) glass fibres reinforced polypropylene was used. Worn sample surfaces were analyzed by SEM after 45.000 and 90.000 cycles. Image analyses were made in order to evaluate the damage increases and to observe the wear mechanisms involved.

Increasing the wear resistance of molds for injection of glass fiber reinforced plastics

Abrasion by glass fibers during injection molding of fiber reinforced plastics raises new challenges to the wear performance of the molds. In the last few decades, a large number of PVD and CVD coatings have been developed with the aim of minimizing abrasion problems. In this work, two different coatings were tested in order to increase the wear resistance of the surface of a mold used for glass fiber reinforced plastics: TiAlSiN and CrN/CrCN/DLC. TiAlSiN was deposited as a graded monolayer coating while CrN/CrCN/DLC was a nanostructured coating consisting of three distinct layers. Both coatings were produced by PVD unbalanced magnetron sputtering and were characterized using scanning electron microscopy (SEM) provided with energy dispersive spectroscopy (EDS), atomic force microscopy (AFM), micro hardness (MH) and scratch test analysis. Coating morphology, thickness, roughness, chemical composition and structure, hardness and adhesion to the substrate were investigated. Wear resistance was characterized through industrial tests with coated samples and an uncoated reference sample inserted in a feed channel of a plastic injection mold working with 30 wt.% glass fiber reinforced polypropylene. Results after 45,000 injection cycles indicate that the wear resistance of the mold was increased by a factor of 25 and 58, by the TiAlSiN and CrN/CrCN/DLC coatings, respectively, over the uncoated mold steel.

Suppression of humoral immunity and lymphocyte responsiveness during experimental trypanosoma cruzi infections

C3H/He and C57B1/6 mice were inoculated with 500 Trypanosoma cruzi trypomastigotes (Strain Y). During the acute phase infected mice presented parasitemia and enlargement of lymph nodes and spleens and intracellular parasites were observed in the heart. Examinations of cells derived from spleen and lymph nodes showed increased numbers of IgM and IgG-bearing cells. During the peak of splenomegaly, about day 17 post-infections, splenic lymphocytes showed a marked decrease in responsiveness to T and B-cell mitogens, parasite antigens and plaque forming cells (PFC) to sheep red blood cells (SRBC). Unfractionated or plastic adherent splenic cells from mice, obtained during the acute phase were able to suppress the response to mitogens by lymphocytes from uninfected mice. During the chronic phase. Disappearance of parasitemia and intracellular parasites in the hearts as well as a decrease in spleen size, was observed. These changes preceded the complete recovery of responsiveness to mitogens and T. cruzi antigens by C57B1/6 splenic lymphocytes. However, this recovery was only partial in the C3H/He mice, known to be more sensitive to T. cruzi infection. Partial recovery of humoral immune response also occurred in both strains of mice during the chronic phase.

Otimização energética na empresa Simoldes Plásticos S.A.

Mestrado em Engenharia Química - Ramo Optimização Energética na Indústria Química

A sustentabilidade e o ciclo de vida dos edifícios

A crescente preocupação que envolve as questões ambientais a nível mundial, cada vez mais agravadas pelo comportamento irresponsável do Homem, conduziu à criação de métodos de avaliação dos impactes ambientais provocados por produtos e sistemas. Sendo o sector da construção responsável por grande parte desses impactes, é evidente a necessidade de aplicação de medidas que visem mitigar ou, no mínimo, reduzir até valores aceitáveis, essas agressões ao meio ambiente. Nesse âmbito, é natural que tenha surgido a ideia de aplicar uma metodologia tão precisa e rigorosa como a LCA ao sector da construção. No entanto, nos dias de hoje, as preocupações alargaram-se às vertentes social e económica que, juntamente com a vertente ambiental, formam o triângulo de equilíbrio do desenvolvimento sustentável. É precisamente essa avaliação tripartida que esta Dissertação pretende abordar, tentando aprofundar conhecimentos e fornecer alternativas, através da análise crítica, que possam contribuir para a melhoria contínua desta metodologia.

O contributo da expressão plástica para o desenvolvimentodas múltiplas linguagens da criança

Relatório da Prática Profissional Supervisionada Mestrado em Educação Pré-Escolar

Melhoria do processo produtivo

A dissertação descreve o levantamento e otimização do processo de fabrico de uma peça plástica para um automóvel. A otimização deste processo produtivo tem em vista a rentabilização de recursos humanos, a redução de custos associados e a redução de atividades ao longo do processo, tais como armazenamento de produto semiacabado, uma vez que este deixa de existir, a eliminação de fluxos logísticos e a eliminação do posto de montagem de componentes desta peça. A metodologia utilizada neste projeto centra-se na aplicação de ferramentas que permitem a análise e melhoria de processos produtivos, tais como o diagrama de processo, o diagrama spaghetti, o PDCA, a cronometragem dos tempos por tarefa e a aplicação de uma heurística para o balanceamento do futuro posto de trabalho da peça em estudo. O diagrama de processo, o diagrama de spaghetti e a cronometragem dos tempos por tarefas mostraram o estado atual do processo produtivo. Da análise do atual estado verifica-se que existe muito desperdício de mão-de-obra nas duas estações de trabalho, injeção e montagem. A eliminação do posto de trabalho exclusivo para montagem e junção dos processos de injeção e montagem no mesmo posto de trabalho, com a aplicação de uma heurística para balanceamento do novo posto de trabalho, demonstra que os ganhos são muito significativos. A aplicação do ciclo PDCA, na base da qual está a elaboração de um plano de ações, tornará esta mudança possível e bem-sucedida. A intenção deste projeto é demonstrar que o estado atual pode sempre ser melhorado se se usarem as ferramentas corretas para análise e proposta de melhorias que trarão ganhos à empresa a curto prazo. Usando esta sugestão, a empresa poderá dar início a um novo ciclo em que o espírito de melhoria esteja presente todos os dias em toda a organização.

A Participação das mulheres na administração das empresas “O Teto de vidro”

Dissertação apresentada ao Instituto Superior de Contabilidade para a obtenção do Grau de Mestre em Auditoria Orientador: Mestre Helena Maria Santos de Oliveira

Fully transparent ZnO thin-film transistor produced at room temperature

Advanced Materials, Vol. 17, nº 5

Estudo comparativo de soluções de materiais poliméricos em redes prediais de água e esgotos

O objetivo deste trabalho é estudar as tubagens de polímeros aplicadas nas redes prediais de águas e esgotos. A utilização deste tipo de material tem vindo a aumentar, mas o conhecimento por parte de projetistas e instaladores não tem vindo a acompanhar o ritmo de crescimento. Esta análise irá permitir um maior conhecimento dos materiais disponíveis e das suas caraterísticas próprias, o que induz a uma escolha acertada e a uma instalação adequada. No início do trabalho clarificou-se o significado e a origem dos polímeros, contando a sua história. Visitou-se a fábrica de tubos Fopil para pesquisar o processamento de polímeros. Explicou-se o fabrico de polímeros, que varia de acordo com as propriedades e aplicações desejadas. Os tubos poliméricos disponíveis no mercado para abastecimento de águas e esgotos foram analisados em relação às suas caraterísticas, vantagens e desvantagens e ligações disponíveis. Existem cuidados a ter no transporte, armazenamento e manuseamento dos tubos. Após a análise das caraterísticas técnicas, fez-se o estudo económico para os tubos existentes no mercado. Para isso foi considerado o abastecimento a um edifício multifamiliar com seis apartamentos. O projetista deve estar sempre informado, quer a nível tecnológico, quer a nível económico, para assim poder fazer a escolha mais acertada a nível de qualidade e a nível de preço. Ao realizar este estudo concluiu-se que nas instalações de redes de abastecimento de águas, o PB é o que tem o preço mais atrativo e tem caraterísticas ótimas. O PE-X tem o preço mais elevado, mas a sua qualidade não é proporcional ao seu preço. Nas instalações de redes de esgotos o material mais económico é o PP, que é o que apresenta as melhores caraterísticas.