Motion artifact reduction and vessel enhancement for free-breathing navigator-gated coronary MRA using 3D k-space reordering.

Breathing-induced bulk motion of the myocardium during data acquisition may cause severe image artifacts in coronary magnetic resonance angiography (MRA). Current motion compensation strategies include breath-holding or free-breathing MR navigator gating and tracking techniques. Navigator-based techniques have been further refined by the applications of sophisticated 2D k-space reordering techniques. A further improvement in image quality and a reduction of relative scanning duration may be expected from a 3D k-space reordering scheme. Therefore, a 3D k-space reordered acquisition scheme including a 3D navigator gated and corrected segmented k-space gradient echo imaging sequence for coronary MRA was implemented. This new zonal motion-adapted acquisition and reordering technique (ZMART) was developed on the basis of a numerical simulation of the Bloch equations. The technique was implemented on a commercial 1.5T MR system, and first phantom and in vivo experiments were performed. Consistent with the results of the theoretical findings, the results obtained in the phantom studies demonstrate a significant reduction of motion artifacts when compared to conventional (non-k-space reordered) gating techniques. Preliminary in vivo findings also compare favorably with the phantom experiments and theoretical considerations. Magn Reson Med 45:645-652, 2001.

Concepts and Reference. Defending a Dual Theory of Natural Kind Concepts

In this thesis I argue that the psychological study of concepts and categorisation, and the philosophical study of reference are deeply intertwined. I propose that semantic intuitions are a variety of categorisation judgements, determined by concepts, and that because of this, concepts determine reference. I defend a dual theory of natural kind concepts, according to which natural kind concepts have distinct semantic cores and non-semantic identification procedures. Drawing on psychological essentialism, I suggest that the cores consist of externalistic placeholder essence beliefs. The identification procedures, in turn, consist of prototypes, sets of exemplars, or possibly also theory-structured beliefs. I argue that the dual theory is motivated both by experimental data and theoretical considerations. The thesis consists of three interrelated articles. Article I examines philosophical causal and description theories of natural kind term reference, and argues that they involve, or need to involve, certain psychological elements. I propose a unified theory of natural kind term reference, built on the psychology of concepts. Article II presents two semantic adaptations of psychological essentialism, one of which is a strict externalistic Kripkean-Putnamian theory, while the other is a hybrid account, according to which natural kind terms are ambiguous between internalistic and externalistic senses. We present two experiments, the results of which support the strict externalistic theory. Article III examines Fodor’s influential atomistic theory of concepts, according to which no psychological capacities associated with concepts constitute them, or are necessary for reference. I argue, contra Fodor, that the psychological mechanisms are necessary for reference.

Cromatografia unificada

The scope of this study encompasses an overview of the principles of unified chromatography as well as the principles of chromatographic techniques as applied to unified systems, which include gas chromatography, liquid chromatography, supercritical fluid chromatography, high temperature and high pressure liquid chromatography, micro-liquid chromatography, enhanced fluidity chromatography, and solvating gas chromatography. Theoretical considerations and individual instrumental parameters such as mobile phase, sample introduction system, columns, and detection system are also discussed. Future applications of this separation approach are discussed.

Opettajien työelämäjaksojen kehitysprojektien mallintaminen osaksi Etelä-Karjalan ammattiopiston toimintaa

Tämän diplomityön tavoitteena oli selvittää, kuinka pilottiprojektien pohjalta voidaan kehittää toimiva prosessimalli. Prosessi, johon uudenlaista kehitystapaa lähdettiin hakemaan, oli Etelä-Karjalan ammattiopiston opettajien työelämäjaksojen toteutusprosessi. Opettajien työelämäjakson erilaisia toteutusmalleja oli testattu jo useammassa eri erilaisten rahoitusten avustuksella perustetuissa pilottiprojektissa. Ulkopuolisen rahoituksen päättyessä tuli ajankohtaiseksi kehittää Etelä-Karjalan ammattiopistolle oma työelämäjaksojen toteutusmalli. Mallin kehitystyössä voitiin hyödyntää aikaisemmista projekteista saatuja palautteita, jolloin mallin kehitystyö lähti liikkeelle tiedossa jo olevista asiakkaan toiveista ja tarpeista. Toimintaa kehitettiin prosessina, koska Etelä-Karjalan ammattiopistossa on alettu satsaamaan voimakkaasti laatuun ja laadun jatkuvaan parantamiseen. Laatua taas ei synny ilman, että toiminnat määriteltäisiin ja kuvattaisiin prosesseina. Koska koulutusorganisaatioille prosessiajattelu on vielä aika vierasta, tässä työssä selvitettiin ensin teoriakatsauksen pohjalta, mitä prosessiajattelu tarkoittaa ja mitä hyötyjä sillä voidaan saavuttaa julkisella sektorilla. Lisäksi kartoitettiin niitä tapoja ja keinoja, joiden avulla prosesseja voitaisiin parantaa ja uudistaa. Prosessin uudistamisprosessiin löytyi teorian pohjalta työkalu, jota muokattiin niin, että sitä voitiin hyödyntää juuri tämäntyyppisessä uudistustyössä. Työn lopputuloksena syntyi työelämäjakson toteutusta kuvaava prosessimalli, jota on jatkossa tarkoitus testata ja kehittää työelämäjaksoilta saadun palautteen perusteella.

Scheduling of guarded command based models

Formal methods provide a means of reasoning about computer programs in order to prove correctness criteria. One subtype of formal methods is based on the weakest precondition predicate transformer semantics and uses guarded commands as the basic modelling construct. Examples of such formalisms are Action Systems and Event-B. Guarded commands can intuitively be understood as actions that may be triggered when an associated guard condition holds. Guarded commands whose guards hold are nondeterministically chosen for execution, but no further control flow is present by default. Such a modelling approach is convenient for proving correctness, and the Refinement Calculus allows for a stepwise development method. It also has a parallel interpretation facilitating development of concurrent software, and it is suitable for describing event-driven scenarios. However, for many application areas, the execution paradigm traditionally used comprises more explicit control flow, which constitutes an obstacle for using the above mentioned formal methods. In this thesis, we study how guarded command based modelling approaches can be conveniently and efficiently scheduled in different scenarios. We first focus on the modelling of trust for transactions in a social networking setting. Due to the event-based nature of the scenario, the use of guarded commands turns out to be relatively straightforward. We continue by studying modelling of concurrent software, with particular focus on compute-intensive scenarios. We go from theoretical considerations to the feasibility of implementation by evaluating the performance and scalability of executing a case study model in parallel using automatic scheduling performed by a dedicated scheduler. Finally, we propose a more explicit and non-centralised approach in which the flow of each task is controlled by a schedule of its own. The schedules are expressed in a dedicated scheduling language, and patterns assist the developer in proving correctness of the scheduled model with respect to the original one.

Defending behavior in bullying situations

In order to encourage children and adolescents to defend and support their victimized peers, it is important to identify factors that either maximize or minimize the probability that students will engage in such behaviors. This thesis is composed of four studies designed to elucidate how a variety of factors work in conjunction to explain why some children defend their victimized classmates, whereas others remain passive or reinforce the bully. The conceptual framework of this thesis is drawn from several theoretical considerations, including social cognitive learning theory, the expectancy-value framework as well as the literature emphasizing the importance of empathy in motivating behaviors. Also the child-by-environment perspective and the socialecological perspective influenced this research. Accordingly, several intra- and interpersonal characteristics (e.g., social cognitions, empathy, and social status) as well as group-level factors (e.g., norms) that may either enhance or reduce the probability that students defend their victimized peers are investigated. In Studies I and II, the focus is on social cognitions, and special attention is paid to take into account the domain-specificity of cognition-behavior processes. Self-efficacy for defending is still an interest of study III, but the role of affective empathy on defending is also investigated. Also social status variables (preference and perceived popularity) are evaluated as possible moderators of links between intrapersonal factors and defending. In Study IV, the focus is expanded further by concentrating on characteristics of children’s proximal environments (i.e., classroom). Bullying norms and collective perceptions (i.e., connectedness among the students and the teachers’ ability to deal with bullying situations) are examined. Data are drawn from two research projects: the Kaarina Cohort Study (consisting of fourth and eighth graders) and the randomized controlled trial (RCT) evaluating the effects of the KiVa antibullying program (consisting of third to fifth graders). The results of the thesis suggest that defending the victims of bullying is influenced by a variety of individual level motivational characteristics, such as social cognitions and affective empathy. Also, both perceived popularity and social preference play a role in defending, and the findings support the conceptualization that behavior results from the interplay between the characteristics of an individual child and their social-relational environment. Classroom context further influences students’ defending behavior. Thus, antibullying efforts targeting peer bystanders should aim to influence intra- and interpersonal characteristics of children and adolescents as well as their social environment.

Agility in international fast fashion retailing

The birth of Internet technologies, the developments of fast fashion and multiple retailing channels have created a need for a new, more integrated way for doing retailing. Agility in fast fashion retailing could be seen as a significant way of responding to these changes and furthermore, as a way to respond to consumers’ altering demands. The purpose of this study was to explore the ways in which agile supply chains and integrated multichannel retailing influence the international fast fashion retailing. A framework for agility in retail was developed based on available theoretical considerations in distribution and communication channels. Qualitative research methods and qualitative content analysis were used. Four expert interviews were carried out to gain new perspectives to the objectives. The rest of the data was collected from an industry specific document, expert video and two expert lectures. Following the data collection, the research material was analyzed with qualitative content analysis. The empirical findings on agility in retail were presented based on a coding frame. It was found that agility in retail has multiple parts, which are overlapping and affecting one another. Furthermore, instead of viewing the agile supply chain and integrated multichannel retailing separately of each other as usual, it was found that they should be integrated, and the term “agility” was proposed to denote this approach. Also, it was found that the most common drivers and constrains of integrated multichannel retailing were the new Internet technologies and customer demand. Brick-and-mortar store, online store, mobile devices and social media were found to be the most common retailing channels. Furthermore, in-store technology, click-and-collect approach, NFC-buying, RFID-technology as well as 3D- digital simulations on fabrics and patterns will enhance agility even more in the future. In addition, environmental issues, customer experiences and communication will be important factors. This study has provided new practical insights for the future retailing. Furthermore, it has contributed to the academic research by discussing the traditional approaches of agility in fast fashion retail and bringing in new insights.

Modified nano- and microcellulose based adsorption materials in water treatment

In recent decades, industrial activity growth and increasing water usage worldwide have led to the release of various pollutants, such as toxic heavy metals and nutrients, into the aquatic environment. Modified nanocellulose and microcellulose-based adsorption materials have the potential to remove these contaminants from aqueous solutions. The present research consisted of the preparation of five different nano/microcellulose-based adsorbents, their characterization, the study of adsorption kinetics and isotherms, the determination of adsorption mechanisms, and an evaluation of adsorbents’ regeneration properties. The same well known reactions and modification methods that were used for modifying conventional cellulose also worked for microfibrillated cellulose (MFC). The use of succinic anhydride modified mercerized nanocellulose, and aminosilane and hydroxyapatite modified nanostructured MFC for the removal of heavy metals from aqueous solutions exhibited promising results. Aminosilane, epoxy and hydroxyapatite modified MFC could be used as a promising alternative for H2S removal from aqueous solutions. In addition, new knowledge about the adsorption properties of carbonated hydroxyapatite modified MFC as multifunctional adsorbent for the removal of both cations and anions ions from water was obtained. The maghemite nanoparticles (Fe3O4) modified MFC was found to be a highly promising adsorbent for the removal of As(V) from aqueous solutions due to its magnetic properties, high surface area, and high adsorption capacity . The maximum removal efficiencies of each adsorbent were studied in batch mode. The results of adsorption kinetics indicated very fast removal rates for all the studied pollutants. Modeling of adsorption isotherms and adsorption kinetics using various theoretical models provided information about the adsorbent’s surface properties and the adsorption mechanisms. This knowledge is important for instance, in designing water treatment units/plants. Furthermore, the correspondence between the theory behind the model and properties of the adsorbent as well as adsorption mechanisms were also discussed. On the whole, both the experimental results and theoretical considerations supported the potential applicability of the studied nano/microcellulose-based adsorbents in water treatment applications.

Liquid cooling solutions for rotating permanent magnet synchronous machines

In the design of electrical machines, efficiency improvements have become very important. However, there are at least two significant cases in which the compactness of electrical machines is critical and the tolerance of extremely high losses is valued: vehicle traction, where very high torque density is desired at least temporarily; and direct-drive wind turbine generators, whose mass should be acceptably low. As ever higher torque density and ever more compact electrical machines are developed for these purposes, thermal issues, i.e. avoidance of over-temperatures and damage in conditions of high heat losses, are becoming of utmost importance. The excessive temperatures of critical machine components, such as insulation and permanent magnets, easily cause failures of the whole electrical equipment. In electrical machines with excitation systems based on permanent magnets, special attention must be paid to the rotor temperature because of the temperature-sensitive properties of permanent magnets. The allowable temperature of NdFeB magnets is usually significantly less than 150 ˚C. The practical problem is that the part of the machine where the permanent magnets are located should stay cooler than the copper windings, which can easily tolerate temperatures of 155 ˚C or 180 ˚C. Therefore, new cooling solutions should be developed in order to cool permanent magnet electrical machines with high torque density and because of it with high concentrated losses in stators. In this doctoral dissertation, direct and indirect liquid cooling techniques for permanent magnet synchronous electrical machines (PMSM) with high torque density are presented and discussed. The aim of this research is to analyse thermal behaviours of the machines using the most applicable and accurate thermal analysis methods and to propose new, practical machine designs based on these analyses. The Computational Fluid Dynamics (CFD) thermal simulations of the heat transfer inside the machines and lumped parameter thermal network (LPTN) simulations both presented herein are used for the analyses. Detailed descriptions of the simulated thermal models are also presented. Most of the theoretical considerations and simulations have been verified via experimental measurements on a copper tooth-coil (motorette) and on various prototypes of electrical machines. The indirect liquid cooling systems of a 100 kW axial flux (AF) PMSM and a 110 kW radial flux (RF) PMSM are analysed here by means of simplified 3D CFD conjugate thermal models of the parts of both machines. In terms of results, a significant temperature drop of 40 ̊C in the stator winding and 28 ̊C in the rotor of the AF PMSM was achieved with the addition of highly thermally conductive materials into the machine: copper bars inserted in the teeth, and potting material around the end windings. In the RF PMSM, the potting material resulted in a temperature decrease of 6 ̊C in the stator winding, and in a decrease of 10 ̊C in the rotor embedded-permanentmagnets. Two types of unique direct liquid cooling systems for low power machines are analysed herein to demonstrate the effectiveness of the cooling systems in conditions of highly concentrated heat losses. LPTN analysis and CFD thermal analysis (the latter being particularly useful for unique design) were applied to simulate the temperature distribution within the machine models. Oil-immersion cooling provided good cooling capability for a 26.6 kW PMSM of a hybrid vehicle. A direct liquid cooling system for the copper winding with inner stainless steel tubes was designed for an 8 MW directdrive PM synchronous generator. The design principles of this cooling solution are described in detail in this thesis. The thermal analyses demonstrate that the stator winding and the rotor magnet temperatures are kept significantly below their critical temperatures with demineralized water flow. A comparison study of the coolant agents indicates that propylene glycol is more effective than ethylene glycol in arctic conditions.

Desenvolvimentismo e novo-desenvolvimentismo: raízes teóricas e precisões conceituais

This paper starts from the conceptualism of New Developmentalism which was proposed by its formulators and their criticism of the "old" developmentalism in order to compare both. It is elaborate in both theoretical and historical levels. In the former, it explores the theoretical streams that contributed to the formulation of economic policies that designated the Latin American developmentalism. In the latter, it focuses on the economic policy of the Brazilian import-substitution industrialization and advocates the impropriety of associating it to the irresponsibility in the management of the foreign exchange, fiscal and monetary policies, as the proposers of New Developmentalism assert. Finally, in a third stage, it resumes the propositions of the New Developmentalism and debates the pertinence of some of its policy propositions based upon theoretical considerations and the Brazilian experience which were mentioned in the previous stages.

A speculative systems model of the dynamic interaction among students, faculty and administration in the community college, with particular reference to intrinsic motivation and the teacher-administrator interface

The challenge the community college faces in helping meet the needs of the living open system of society is examined in this study. It is postulated that internalization student outcomes are required by society to reduce entropy and remain self-renewing. Such behavior is characterized as having an intrinsically motivated energy source and displays the seeking and conquering of challenge, the development of reflective knowledge and skill, full use of all capabilities, internal control, growth orientation, high self-esteem, relativistic thinking and competence. The development of a conceptual systems model that suggests how transactions among students, faculty and administration might occur to best meet the needs of internalization outcomes in students, and intrinsic motivation in faculty is a major purpose of this study. It is a speculative model that is based on a synthesis of a wide variety of variables. Empirical evidence, theoretical considerations, and speculative ideas are gathered together from researchers and theoretici.ans who are working on separate answers to questions of intrinsic motivation, internal control and environments that encourage their development. The model considers the effect administrators·have on faculty anq the corresponding effect faculty may have on students. The major concentration is on the administrator--teacher interface.For administrators the model may serve as a guide in planning effective transactions, and establishing system goals. The teacher is offered a means to coordinate actions toward a specific overall objective, and the administrator, teacher and researcher are invited to use the model to experiment, innovate, verify the assumptions on which the model is based, and raise additional hypotheses. Goals and history of the community colleges in Ontario are examined against current problems, previous progress and open system thinking. The nature of the person as a five part system is explored with emphasis on intrinsic motivation. The nature, operation, conceptualization, and value of this internal energy source is reviewed in detail. The current state of society, education and management theory are considered and the value of intrinsically motivating teaching tasks together with "system four" leadership style are featured. Evidence is reviewed that suggests intrinsically motivated faculty are needed, and "system four" leadership style is the kind of interaction-influence system needed to nurture intrinsic motivation in faculty.

An approximation method using approximate approximations

The aim of this paper is to extend the method of approximate approximations to boundary value problems. This method was introduced by V. Maz'ya in 1991 and has been used until now for the approximation of smooth functions defined on the whole space and for the approximation of volume potentials. In the present paper we develop an approximation procedure for the solution of the interior Dirichlet problem for the Laplace equation in two dimensions using approximate approximations. The procedure is based on potential theoretical considerations in connection with a boundary integral equations method and consists of three approximation steps as follows. In a first step the unknown source density in the potential representation of the solution is replaced by approximate approximations. In a second step the decay behavior of the generating functions is used to gain a suitable approximation for the potential kernel, and in a third step Nyström's method leads to a linear algebraic system for the approximate source density. For every step a convergence analysis is established and corresponding error estimates are given.

Approximate solutions and error estimates for a Stokes boundary value problem

The aim of this paper is the numerical treatment of a boundary value problem for the system of Stokes' equations. For this we extend the method of approximate approximations to boundary value problems. This method was introduced by V. Maz'ya in 1991 and has been used until now for the approximation of smooth functions defined on the whole space and for the approximation of volume potentials. In the present paper we develop an approximation procedure for the solution of the interior Dirichlet problem for the system of Stokes' equations in two dimensions. The procedure is based on potential theoretical considerations in connection with a boundary integral equations method and consists of three approximation steps as follows. In a first step the unknown source density in the potential representation of the solution is replaced by approximate approximations. In a second step the decay behavior of the generating functions is used to gain a suitable approximation for the potential kernel, and in a third step Nyström's method leads to a linear algebraic system for the approximate source density. For every step a convergence analysis is established and corresponding error estimates are given.

Lost in Research - Wissensmanagement in komplexen (psychoanalytischen) Forschungsprojekten

Die Wissenschaft weist im Zuge der Entwicklung von der Industrie- zu einer Wissensgesellschaft einschneidende Veränderungen in der Wissensordnung auf, welche sich bis hin zu einem zunehmenden Verlust der wissenschaftlichen Selbststeuerungsmechanismen bemerkbar machen und einen veränderten Umgang mit dem generierten Wissensschatz erfordern. Nicht nur Änderungen in der Wissensordnung und -produktion stellen die Psychoanalyse vor neue Herausforderungen: In den letzten Jahrzehnten geriet sie als Wissenschaft und Behandlungsverfahren zunehmend in die Kritik und reagierte mit einer konstruktiven Diskussion um ein dem Forschungsgegenstand – die Untersuchung unbewusster Prozesse und Fantasien – adäquates psychoanalytisches Forschungsverständnis. Die Auseinandersetzung mit Forderungen gesellschaftlicher Geldgeber, politischer Vertreter und Interessensgruppen wie auch der wissenschaftlichen Community stellt die Psychoanalyse vor besondere Herausforderungen. Um wissenschaftsexternen wie -internen Gütekriterien zu genügen, ist häufig ein hoher personeller, materieller, finanzieller, methodischer wie organisatorischer Aufwand unabdingbar, wie das Beispiel des psychoanalytischen Forschungsinstitutes Sigmund-Freud-Institut zeigt. Der steigende Aufwand schlägt sich in einer zunehmenden Komplexität des Forschungsprozesses nieder, die unter anderem in den vielschichtigen Fragestellungen und Zielsetzungen, dem vermehrt interdisziplinären, vernetzten Charakter, dem Umgang mit dem umfangreichen, hochspezialisierten Wissen, der Methodenvielfalt, etc. begründet liegt. Um jener Komplexität des Forschungsprozesses gerecht zu werden, ist es zunehmend erforderlich, Wege des Wissensmanagement zu beschreiten. Tools wie z. B. Mapping-Verfahren stellen unterstützende Werkzeuge des Wissensmanagements dar, um den Herausforderungen des Forschungsprozesses zu begegnen. In der vorliegenden Arbeit werden zunächst die veränderten Forschungsbedingungen und ihre Auswirkungen auf die Komplexität des Forschungsprozesses - insbesondere auch des psychoanalytischen Forschungsprozesses - reflektiert. Die mit der wachsenden Komplexität einhergehenden Schwierigkeiten und Herausforderungen werden am Beispiel eines interdisziplinär ausgerichteten EU-Forschungsprojektes näher illustriert. Um dieser wachsenden Komplexität psychoanalytischer Forschung erfolgreich zu begegnen, wurden in verschiedenen Forschungsprojekten am Sigmund-Freud-Institut Wissensmanagement-Maßnahmen ergriffen. In der vorliegenden Arbeit wird daher in einem zweiten Teil zunächst auf theoretische Aspekte des Wissensmanagements eingegangen, die die Grundlage der eingesetzten Wissensmanagement-Instrumente bildeten. Dabei spielen insbesondere psychologische Aspekte des Wissensmanagements eine zentrale Rolle. Zudem werden die konkreten Wissensmanagement-Tools vorgestellt, die in den verschiedenen Forschungsprojekten zum Einsatz kamen, um der wachsenden Komplexität psychoanalytischer Forschung zu begegnen. Abschließend werden die Hauptthesen der vorliegenden Arbeit noch einmal reflektiert und die geschilderten Techniken des Wissensmanagements im Hinblick auf ihre Vor- und Nachteile kritisch diskutiert.

Evaluación a largo plazo en mujeres tratadas con laser para depilación facial en uniláser medica

El vello facial no deseado es un problema común en las mujeres, los tratamientos láser han mostrado efectividad para su manejo. Objetivo: Evaluar los resultados de la depilación láser en cara de las pacientes tratadas a largo plazo (20 sesiones o más ) luego de un seguimiento de 6 meses durante los años 1997 y 2012. Metodología: 55 mujeres que con tipo de piel II a V recibieron 20 o más sesiones de láser con seguimiento mayor a 6 meses posterior al la última sesión. Resultados: la edad promedio fue (32 ± 9,3 años), el 18,2 % presentaban SOP o Hiperandrogenismo el número de sesiones en cara fue de (30,84 ± 12,132), un promedio de disparos de (6,330 ± 7,804), los Kilojulios acumulados tuvieron un promedio de (126,5 ± 161,4) la fluencia promedio fue (18,5 ± 3,2 Julios/cm2), el láser de Alexandrita fue utilizado en el 98% de las pacientes. Se encontró cambios significativos entre el conteo inicial y el final de vello facial (484,9 ± 568.9 (med=300) vs. 103,33± 138,63 (med=60), p<0.001, Test de Wilcoxon). El 32.7% mostraron reducción > 90% (5,5% reducción del 100%). Conclusión : El tratamiento con de depilación con láser mostro una reducción significativa del vello facial, en mujeres mayores de 14 años con un tratamiento a largo plazo (20 sesiones o más), con una tasa de reducción mayor del 90% en 32.7% de las pacientes y un promedio de reducción del grupo de 79,36 ±15,51 %, similar a lo reportado en los diferentes estudios (77%).