Noise in gallium nitride-based quantum well structures used for nanometer devices in the frequency range 1 Hz--3 Mhz and temperature range 77K--324K

Electronic noise has been investigated in AlxGa1−x N/GaN Modulation-Doped Field Effect Transistors (MODFETs) of submicron dimensions, grown for us by MBE (Molecular Beam Epitaxy) techniques at Virginia Commonwealth University by Dr. H. Morkoç and coworkers. Some 20 devices were grown on a GaN substrate, four of which have leads bonded to source (S), drain (D), and gate (G) pads, respectively. Conduction takes place in the quasi-2D layer of the junction (xy plane) which is perpendicular to the quantum well (z-direction) of average triangular width ∼3 nm. A non-doped intrinsic buffer layer of ∼5 nm separates the Si-doped donors in the AlxGa1−xN layer from the 2D-transistor plane, which affords a very high electron mobility, thus enabling high-speed devices. Since all contacts (S, D, and G) must reach through the AlxGa1−xN layer to connect internally to the 2D plane, parallel conduction through this layer is a feature of all modulation-doped devices. While the shunting effect may account for no more than a few percent of the current IDS, it is responsible for most excess noise, over and above thermal noise of the device. ^ The excess noise has been analyzed as a sum of Lorentzian spectra and 1/f noise. The Lorentzian noise has been ascribed to trapping of the carriers in the AlxGa1−xN layer. A detailed, multitrapping generation-recombination noise theory is presented, which shows that an exponential relationship exists for the time constants obtained from the spectral components as a function of 1/kT. The trap depths have been obtained from Arrhenius plots of log (τT2) vs. 1000/T. Comparison with previous noise results for GaAs devices shows that: (a) many more trapping levels are present in these nitride-based devices; (b) the traps are deeper (farther below the conduction band) than for GaAs. Furthermore, the magnitude of the noise is strongly dependent on the level of depletion of the AlxGa1−xN donor layer, which can be altered by a negative or positive gate bias VGS. ^ Altogether, these frontier nitride-based devices are promising for bluish light optoelectronic devices and lasers; however, the noise, though well understood, indicates that the purity of the constituent layers should be greatly improved for future technological applications. ^

A utilização da pesquisa operacional para o gerenciamento dos leitos em um hospital particular: estudo de caso baseado em simulação computacional

The hospital is a place of complex actions, where several activities for serving the population are performed such as: medical appointments, exams, surgeries, emergency care, admission in wards and ICUs. These activities are mixed with anxiety, impatience, despair and distress of patients and their families, issues involving emotional balance both for professionals who provide services for them as for people cared by them. The healthcare crisis in Brazil is getting worse every year and today, constitutes a major problem for private hospitals. The patient that comes to emergencies progressively increase, and in contrast, there is no supply of hospital beds in the same proportion, causing overcrowding, declines in the quality of care delivered to patients, drain of professionals of the health area and difficulty in management the beds. This work presents a study that seeks to create an alternative tool that can contribute to the management of a private hospital beds. It also seeks to identify potential issues or deficiencies and therefore make changes in flow for an increase in service capacity, thus reducing costs without compromising the quality of services provided. The tool used was the Computational Simulation –based in discrete event, which aims to identify the main parameters to be considered for a proper modeling of this system. This study took as reference the admission of a private hospital, based on the current scenario, where your apartments are in saturation level as its occupancy rate. The relocation of project beds aims to meet the growing demand for surgeries and hospital admissions observed by the current administration.

Análise comparativa de diferentes configurações de poços no processo de combustão in-situ

With an increasing number of mature fields, heavy oil recovery has performed one of the great challenges of the oil industry. The Brazilian Northeast, for example, has numerous heavy oil reservoirs are explored with the use of thermal methods. Among the types of methods used for heavy oil, there is the method of in-situ combustion, a technique in which heat is produced within the container, unlike the injection of heated fluid when the heat is generated at the surface and transported to the reservoir. In this type of process, it is common to use vertical wells as injectors and producers. However, methods which use horizontal wells like oil producers are increasingly studied because of greater contact area between the formation and combustion front. Thus, the main objective of this work was to study the different configurations of wells (CIS THAITM and CAGD) in the process of in-situ combustion in oil recovery using a semi-synthetic tank with Brazilian Northeast features. The method "toe-to-heel air injection" (THAITM) is a process of enhanced oil recovery, which is the integration of in-situ combustion with technological advances in drilling horizontal wells. This method uses horizontal wells such as oil producers, keeping vertical injection wells for injecting air. The oil drain process by differential gravitational assisted with combustion (CAGD) is an integrated, in this configuration the horizontal injector well is drilled at the top formation with a horizontal production well in the lower section. The simulations were performed in a commercial program of thermal processes, called "STARS" (Steam, Thermal, and Advanced Processes Reservoir Simulator), the company CMG (Computer Modelling Group). An analysis of the air flow injection was performed and it was found that each method had a maximum injection to the base model, a show that through this air injection limit was reduced cumulative production of oil. Analyses of operating parameters were used: injection flow, configuration and completion of wells. In the sensitivity analysis we found that the air injection flow showed greater influence on THAI method, since the CIS method the completion of the wells was the most influential parameter and CAGD configuration wells showed the greatest influence in the recovered fraction. The economic results have shown that the best case obtained in CAGD method because, despite having higher initial cost showed the best financial return compared to the best cases the CIS and THAI.

Análise comparativa de diferentes configurações de poços no processo de combustão in-situ

With an increasing number of mature fields, heavy oil recovery has performed one of the great challenges of the oil industry. The Brazilian Northeast, for example, has numerous heavy oil reservoirs are explored with the use of thermal methods. Among the types of methods used for heavy oil, there is the method of in-situ combustion, a technique in which heat is produced within the container, unlike the injection of heated fluid when the heat is generated at the surface and transported to the reservoir. In this type of process, it is common to use vertical wells as injectors and producers. However, methods which use horizontal wells like oil producers are increasingly studied because of greater contact area between the formation and combustion front. Thus, the main objective of this work was to study the different configurations of wells (CIS THAITM and CAGD) in the process of in-situ combustion in oil recovery using a semi-synthetic tank with Brazilian Northeast features. The method "toe-to-heel air injection" (THAITM) is a process of enhanced oil recovery, which is the integration of in-situ combustion with technological advances in drilling horizontal wells. This method uses horizontal wells such as oil producers, keeping vertical injection wells for injecting air. The oil drain process by differential gravitational assisted with combustion (CAGD) is an integrated, in this configuration the horizontal injector well is drilled at the top formation with a horizontal production well in the lower section. The simulations were performed in a commercial program of thermal processes, called "STARS" (Steam, Thermal, and Advanced Processes Reservoir Simulator), the company CMG (Computer Modelling Group). An analysis of the air flow injection was performed and it was found that each method had a maximum injection to the base model, a show that through this air injection limit was reduced cumulative production of oil. Analyses of operating parameters were used: injection flow, configuration and completion of wells. In the sensitivity analysis we found that the air injection flow showed greater influence on THAI method, since the CIS method the completion of the wells was the most influential parameter and CAGD configuration wells showed the greatest influence in the recovered fraction. The economic results have shown that the best case obtained in CAGD method because, despite having higher initial cost showed the best financial return compared to the best cases the CIS and THAI.

The impact of routine open nonsuction drainage on fluid accumulation after thyroid surgery: a prospective randomised clinical trial.

Background: Thyroid drains following thyroid surgery are routinely used despite minimal supportive evidence. Our aim in this study is to determine the impact of routine open drainage of the thyroid bed postoperatively on ultrasound-determined fluid accumulation at 24 hours. Methods: We conducted a prospective randomised clinical trial on patients undergoing thyroid surgery. Patients were randomly assigned to a drain group (n = 49) or a no-drain group (n = 44) immediately prior to wound closure. Patients underwent a neck ultrasound on day 1 and day 2 postoperatively. After surgery, we evaluated visual analogue scale pain scores, postoperative analgesic requirements, self-reported scar satisfaction at 6 weeks and complications. Results: There was significantly less mean fluid accumulated in the drain group on both day 1, 16.4 versus 25.1 ml (P-value = 0.005), and day 2, 18.4 versus 25.7 ml (P-value = 0.026), following surgery. We found no significant differences between the groups with regard to length of stay, scar satisfaction, visual analogue scale pain score and analgesic requirements. There were four versus one wound infections in the drain versus no-drain groups. This finding was not statistically significant (P = 0.154). No life-threatening bleeds occurred in either group. Conclusions: Fluid accumulation after thyroid surgery was significantly lessened by drainage. However, this study did not show any clinical benefit associated with this finding in the non-emergent setting. Drains themselves showed a trend indicating that they may augment infection rates. The results of this study suggest that the frequency of acute life-threatening bleeds remains extremely low following abandoning drains. We advocate abandoning routine use of thyroid drains. Trial registration: ISRCTN94715414.

The Effect of Propofol Versus Isoflurane Anesthesia on Human Cerebrospinal Fluid Markers of Alzheimer's Disease: Results of a Randomized Trial.

BACKGROUND: Preclinical studies have found differential effects of isoflurane and propofol on the Alzheimer's disease (AD)-associated markers tau, phosphorylated tau (p-tau) and amyloid-β (Aβ). OBJECTIVE: We asked whether isoflurane and propofol have differential effects on the tau/Aβ ratio (the primary outcome), and individual AD biomarkers. We also examined whether genetic/intraoperative factors influenced perioperative changes in AD biomarkers. METHODS: Patients undergoing neurosurgical/otolaryngology procedures requiring lumbar cerebrospinal fluid (CSF) drain placement were prospectively randomized to receive isoflurane (n = 21) or propofol (n = 18) for anesthetic maintenance. We measured perioperative CSF sample AD markers, performed genotyping assays, and examined intraoperative data from the electronic anesthesia record. A repeated measures ANOVA was used to examine changes in AD markers by anesthetic type over time. RESULTS: The CSF tau/Aβ ratio did not differ between isoflurane- versus propofol-treated patients (p = 1.000). CSF tau/Aβ ratio and tau levels increased 10 and 24 h after drain placement (p = 2.002×10-6 and p = 1.985×10-6, respectively), mean CSF p-tau levels decreased (p = 0.005), and Aβ levels did not change (p = 0.152). There was no interaction between anesthetic treatment and time for any of these biomarkers. None of the examined genetic polymorphisms, including ApoE4, were associated with tau increase (n = 9 polymorphisms, p > 0.05 for all associations). CONCLUSION: Neurosurgery/otolaryngology procedures are associated with an increase in the CSF tau/Aβ ratio, and this increase was not influenced by anesthetic type. The increased CSF tau/Aβ ratio was largely driven by increases in tau levels. Future work should determine the functional/prognostic significance of these perioperative CSF tau elevations.

Immunotherapy for the treatment of poor prognosis cancers

Cancer is amongst the leading causes of death worldwide and the number one cause in the developed world. Every year there are close to 10 million cancer related deaths and this corresponds to hundreds of millions of euro in health care costs and lost productivity, placing a substantial drain on the economy. The efficacy of traditional treatment modalities for cancer therapy, such as surgery, radiotherapy and chemotherapy has plateaued, and while they are undoubtedly effective at prolonging patient lifespan, there is a high rate of adverse side effects and fatal reoccurrence. Currently, there is a huge amount of interest in the areas of cancer immunosurveillance and cancer immuno-editing, which explain some of the complex interactions between the host immune system and cancer. If left unchecked, cancerous malignancies have the ability to generate an immunosuppressive microenvironment, effectively shielding themselves from elimination and promoting tumour growth and progression. To overcome this, the potential of the immune system must be harnessed and the work undertaken in this thesis sought to contribute to this goal. Focus was placed on using novel therapies, combining tumour ablation with immune-modulating antibodies to maximise tumour elimination in an immune dependent manner, to overcome immunosuppression and promote immune activation. Chapter 2 focuses on the use of ECT as a method of tumour ablation and its effects on the immune system. ECT proved to be effective at inhibiting the tumour growth both in vitro and in vivo, and conferred significant survival advantages in both small and large animal models. More importantly, ECT proved to cause tumour death in an immune dependent manner, displaying the hallmarks of Immunogenic Cell Death, increases in immune cell infiltration and generating tumour-specific immune responses. Chapter 3 focuses on combining ECT with immune checkpoint blockade inhibitors; anti- CTLA-4 and anti-PD-1. Both combinations proved to be effective at inhibiting both primary and distal tumour growth, indicating the generation of tumour specific immune responses and prolonged animal survival. In addition, the treatments caused increases in the levels of certain intra-tumoural immune cell subsets and modulated the cytokine profile of treated animals in a way that was favourable overall. Chapter 4 focuses on the combining ECT with an anti-iCOS agonist antibody, capable of causing immune co-stimulation. This novel combinational therapy proved to be the most effective by far, with a high cure rate achieved across a number of different in vivo tumour models. Total regression was seen in both primary and distal tumours, as well as spontaneous metastases, with the tumour specific immune response generated conferring total protection to animals on tumour rechallenge. Overall the data presented here adds further insight into the area of cancer immunotherapy with some of the novel combinational therapies demonstrating substantial clinic potential.

Organic functionalisation, doping and characterisation of semiconductor surfaces for future CMOS device applications

Organic Functionalisation, Doping and Characterisation of Semiconductor Surfaces for Future CMOS Device Applications Semiconductor materials have long been the driving force for the advancement of technology since their inception in the mid-20th century. Traditionally, micro-electronic devices based upon these materials have scaled down in size and doubled in transistor density in accordance with the well-known Moore’s law, enabling consumer products with outstanding computational power at lower costs and with smaller footprints. According to the International Technology Roadmap for Semiconductors (ITRS), the scaling of metal-oxide-semiconductor field-effect transistors (MOSFETs) is proceeding at a rapid pace and will reach sub-10 nm dimensions in the coming years. This scaling presents many challenges, not only in terms of metrology but also in terms of the material preparation especially with respect to doping, leading to the moniker “More-than-Moore”. Current transistor technologies are based on the use of semiconductor junctions formed by the introduction of dopant atoms into the material using various methodologies and at device sizes below 10 nm, high concentration gradients become a necessity. Doping, the controlled and purposeful addition of impurities to a semiconductor, is one of the most important steps in the material preparation with uniform and confined doping to form ultra-shallow junctions at source and drain extension regions being one of the key enablers for the continued scaling of devices. Monolayer doping has shown promise to satisfy the need to conformally dope at such small feature sizes. Monolayer doping (MLD) has been shown to satisfy the requirements for extended defect-free, conformal and controllable doping on many materials ranging from the traditional silicon and germanium devices to emerging replacement materials such as III-V compounds This thesis aims to investigate the potential of monolayer doping to complement or replace conventional doping technologies currently in use in CMOS fabrication facilities across the world.

Analysis of Evidence from Core Sample Fractures in Stewardson Lake Uranium Prospect

This study was performed to characterize evidence of potential unconformity-type U mineralizing fluids in drill core fractures from the Stewardson Lake prospect, in the Athabasca Basin, located in Northern Saskatchewan and Alberta, Canada. Fractures were visually classified into eight varieties. This classification scheme was improved with the use of mineralogical characterization through SEM (Scanning Electron Microscope) and XRD analyses of the fracture fills and resulted in the identification of various oxides, hydroxides, sulfides, and clays or clay-sized minerals. Fractures were tallied to a total of ten categories with some commonalities in color. The oxidative, reductive or mixed nature of the fluids interacting with each fracture was determined based on its fill mineralogy. The measured Pb isotopic signature of samples was used to distinguish fractures affected solely by fluids emanating from a U mineralization source, from those affected by mixed fluids. Anomalies in U and U-pathfinder elements detected in fractures assisted with attributing them to the secondary dispersion halo of potential mineralization. Three types of fracture functions (chimney, composite and drain) were defined based on their interpreted flow vector and history. A secondary dispersion halo boundary with a zone of dominance of infiltrating fluids was suggested for two boreholes. The control of fill mineralogy on fracture color was investigated and the indicative and non-indicative colors and minerals, with respect to a secondary dispersion halo, were formally described. The fracture colors and fills indicative of proximity to the basement host of the potential mineralization were also identified. In addition, three zones of interest were delineated in the boreholes with respect to their geochemical dynamics and their relationship to the potential mineralization: a shallow barren overburden zone, a dispersion and alteration zone at intermediate depth, and a second deeper zone of dispersion and alteration.

Leaving and Coming Back to Canada : Evidence from Longitudinal Data (Working Paper 32)

The paper exploits the unique strengths of Statistics Canada's Longitudinal Administrative Database ("LAD"), constructed from individuals' tax records, to shed new light on the extent and nature of the emigration of Canadians to other countries and their patterns of return over the period 1982-1999. The empirical evidence begins with some simple graphs of the overall rates of leaving over time, and follows with the presentation of the estimation results of a model that essentially addresses the question: "who moves?" The paper then analyses the rates of return for those observed to leave the country - something for which there is virtually no existing evidence. Simple return rates are reported first, followed by the results of a hazard model of the probability of returning which takes into account individuals' characteristics and the number of years they have already been out of the country. Taken together, these results provide a new empirical basis for discussions of emigration in general, and the brain drain in particular. Of particular interest are the ebb and flow of emigration rates observed over the last two decades, including a perhaps surprising turndown in the most recent years after climbing through the earlier part of the 1990s; the data on the number who return after leaving, the associated patterns by income level, and the increases observed over the last decade.

The elderly care and domestic services sector during the recent economic crisis. The case of Italy, Spain and France.

Over the past ten years in Italy, Spain and France, the demographic pressure and the increasing women’s participation in labour market have fuelled the expansion of the private provision of domestic and care services. In order to ensure the difficult balance between affordability, quality and job creation, each countries’ response has been different. France has developed policies to sustain the demand side introducing instruments such as vouchers and fiscal schemes, since the mid of the 2000s. Massive public funding has contributed to foster a regular market of domestic and care services and France is often presented as a “best practices” of those policies aimed at encouraging a regular private sector. Conversely in Italy and Spain, the development of a private domestic and care market has been mostly uncontrolled and without a coherent institutional design: the osmosis between a large informal market and the regular private care sector has been ensured on the supply side by migrant workers’ regularizations or the introduction of new employment regulations . The analysis presented in this paper aims to describe the response of these different policies to the challenges imposed by the current economic crisis. In dealing with the retrenchment of public expenditure and the reduced households’ purchasing power, Italy, Spain and France are experiencing greater difficulties in ensuring a regular private sector of domestic and care services. In light of that, the paper analyses the recent economic conjuncture presenting some assumptions about the future risk of deeper inequalities rising along with the increase of the process of marketization of domestic and care services in all the countries under analysis.    

Late-career international migration and reproductive work. A comparison between Peruvian and Ukrainian women in the Southern Europe

Research on the relationship between reproductive work and women´s life trajectories including the experience of labour migration has mainly focused on the case of relatively young mothers who leave behind, or later re-join, their children. While it is true that most women migrate at a younger age, there are a significant number of cases of men and women who move abroad for labour purposes at a more advanced stage, undertaking a late-career migration. This is still an under-estimated and under-researched sub-field that uncovers a varied range of issues, including the global organization of reproductive work and the employment of migrant women as domestic workers late in their lives. By pooling the findings of two qualitative studies, this article focuses on Peruvian and Ukrainian women who seek employment in Spain and Italy when they are well into their forties, or older. A commonality the two groups of women share is that, independently of their level of education and professional experience, more often than not they end up as domestic and care workers. The article initially discusses the reasons for late-career female migration, taking into consideration the structural and personal determinants that have affected Peruvian and Ukrainian women’s careers in their countries of origin and settlement. After this, the focus is set on the characteristics of domestic employment at later life, on the impact on their current lives, including the transnational family organization, and on future labour and retirement prospects. Apart from an evaluation of objective working and living conditions, we discuss women’s personal impressions of being domestic workers in the context of their occupational experiences and family commitments. In this regard, women report varying levels of personal and professional satisfaction, as well as different patterns of continuity-discontinuity in their work and family lives, and of optimism towards the future. Divergences could be, to some extent, explained by the effect of migrants´ transnational social practices and policies of states.

Migrant domestic workers, vulnerability and the law: immigration and employment laws in Cyprus and Spain

The intersection of gender, welfare and immigration regimes has been one of the main focus of a rich scholarship on paid domestic work in Europe. This article brings into the discussion the nexus of employment and immigration law regimes to reflect on the role of legal regulation in structuring and reducing the vulnerability of domestic workers. I analyse this nexus by looking at the cases of Cyprus and Spain, two states falling under the cluster of Southern Mediterranean welfare regimes, that share certain characteristics in terms of immigration regimes, but have substantially different employment law regulation models. The first part sketches the debate on the employment law regulation of domestic work. The second part starts by giving an overview of the immigration regimes of Cyprus and Spain in relation to migrant domestic workers and then proceeds to analyse the two countries’ models and substance of employment law regulation in domestic work. The comparison of these two divergent approaches informs the debate on how the legal regulation of domestic work should be best structured. In Spain there have been recent dynamic legislative changes in the employment law regulation of domestic work. The final part of the article traces these changes and reflects on why such processes have not taken place in Cyprus.

Understandings of transnational families in debates on Migration and development

International migration sets in motion a range of significant transnational processes that connect countries and people. How migration interacts with development and how policies might promote and enhance such interactions have, since the turn of the millennium, gained attention on the international agenda. The recognition that transnational practices connect migrants and their families across sending and receiving societies forms part of this debate. The ways in which policy debate employs and understands transnational family ties nevertheless remain underexplored. This article sets out to discern the understandings of the family in two (often intermingled) debates concerned with transnational interactions: The largely state and policydriven discourse on the potential benefits of migration on economic development, and the largely academic transnational family literature focusing on issues of care and the micro-politics of gender and generation. Emphasizing the relation between diverse migration-development dynamics and specific family positions, we ask whether an analytical point of departure in respective transnational motherhood, fatherhood or childhood is linked to emphasizing certain outcomes. We conclude by sketching important strands of inclusions and exclusions of family matters in policy discourse and suggest ways to better integrate a transnational family perspective in global migration-development policy.

Perspectives on gender, migration and transnational work: joint work of social reproduction and care in Southern Europe

This paper presents the "state of the art" and some of the main issues discussed in relation to the topic of transnational migration and reproductive work in southern Europe. We start doing a genealogy of the complex theoretical development leading to the consolidation of the research program, linking consideration of gender with transnational migration and transformation of work and ways of survival, thus making the production aspects as reproductive, in a context of globalization. The analysis of the process of multiscale reconfiguration of social reproduction and care, with particular attention to its present global dimension is presented, pointing to the turning point of this line of research that would have taken place with the beginning of this century, with the rise notions such as "global care chains" (Hochschild, 2001), or "care drain" (Ehrenreich and Hochschild, 2013). Also, the role of this new agency, now composed in many cases women who migrate to other countries or continents, precisely to address these reproductive activities, is recognized. Finally, reference is made to some of the new conceptual and theoretical developments in this area.