DLTS investigation of acceptor states in P3MeT Schottky barrier diodes

Deep Level Transient Spectroscopy (DLTS) has been used to investigate hole traps in the depletion region of Schottky barrier diodes formed from electropolymerised poly(3-methylthiophene). The capacitance transients appear to be composed of a fast and a slow component. Analysis of the slower component using the ''rate window'' technique yields isochronal differential capacitance curves that depend on temperature in the manner predicted by theory.

Influence of fabrication conditions on the electrical behaviour of polymer Schottky diodes

Evidence is presented which shows that anomalies in the I-V characteristics of Schottky diodes formed from electrodeposited poly(3-methylthiophene) are related to the time films are held under vacuum prior to deposition of the rectifying aluminium electrode. For short times (similar to 15 mins) a plateau appears in the forward bias characteristic which disappears leading to a significant voltage offset as the device ages or is driven into high forward bias.

Determination of deep and shallow levels in conjugated polymers by electrical methods

Conjugated organic semiconductors have been submitted to various electrical measurement techniques in order to reveal information about shallow levels and deep traps in the forbidden gap. The materials consisted of poly[2-methoxy, 5 ethyl (2' hexyloxy) paraphenylenevinylene] (MEH-PPV), poly(3-methylthiophene) (PMeT), and alpha-sexithienyl (alpha T6) and the employed techniques were IV, CV, admittance spectroscopy, TSC, capacitance and current transients. (C) 1999 Elsevier Science B.V. All rights reserved.

Schottky barriers to semiconducting polymers

Schottky barrier diodes are made from virtually all semiconducting polymers. Application of Schottky barriers on the development of electronic devices built from semiconducting polymers prompted this research. The article investigated the dc and ac admittance of Schottky barrier which occur at the interface between aluminum and poly(3-methyl thiophene) made ready by electropolymerisation. The experiment revealed that the interfacial layers occurring in polymer Schottky barriers is significant in the response of the controlling device.

Photocurrents in P3MeT Schottky barrier diodes

The photocurrent action spectrum of a Schottky diode formed from electrodeposited poly(3-methylthiophene) is shown to follow closely the UV-visible absorption spectrum. At low forward bias, the peak photocurrent asymptotes to the expected square-root dependence on total potential, V-t, across the depletion region. At high reverse bias the superlinear dependence of the photocurrent on V-t suggests that internal photoemission from the rectifying aluminium electrode may be the dominant process.

Electrical study of impurity states in conjugated polymers

Schottky diodes resulting from an intimate contact of aluminum on electro-deposited poly(3-methylthiopene), PMeT, have been studied by admittance spectroscopy, capacitance-voltage and current-voltage measurements, and optically-induced current transients. The loss-tangents show the existence of interface states that can be removed by vacuum annealing, also visible in the transients. Furthermore, the CV curves don't substantiate the idea of movement of the dopant ions.

Electrical characterization of semiconducting polymers

Schottky diodes resulting from an intimate contact of aluminum on electrodeposited poly(3-methylthiopene) were studied by admittance spectroscopy, capacitance-voltage measurements and voltaic and optically-induced current and capacitance transients. The loss tangents show the existence of interface states that can be removed by vacuum annealing. Furthermore, the C-V curves contradict the idea of movement of the dopant ions.

Schottky barrier diodes from semiconducting polymers

Schottky barrier diodes based on Al/poly(3-methylthiophene)/Au have been fabricated and their electrical behaviour investigated. I-V characteristics revealed a dependence on the fabrication conditions, specifically on the time under vacuum prior to evaporation of the rectifying contact and post-metal annealing at elevated temperature. The available evidence is consistent with the formation of a thin insulating layer between the metal and the polymer following these procedures. Long periods under vacuum prior to deposition of the aluminium electrode reduced the likelihood of such a layer forming. Capacitance-voltage plots of the devices were stable to voltage cycling, so long as the forward voltage did not exceed similar to 1 V. Above this a small degree of hysteresis was observed, which is attributed to the filling/emptying of interface states or traps in the polymer.

Poly(hydroxybutyrate-co-hydroxyvalerate) microspheres loaded with atrazine herbicide: screening of conditions for preparation, physico-chemical characterization, and in vitro release studies

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Evaluation of immobilized lipases on poly-hydroxybutyrate beads to catalyze biodiesel synthesis

Five microbial lipase preparations from several sources were immobilized by hydrophobic adsorption on small or large poly-hydroxybutyrate (PHB) beads and the effect of the support particle size on the biocatalyst activity was assessed in the hydrolysis of olive oil, esterification of butyric acid with butanol and transesterification of babassu oil (Orbignya sp.) with ethanol. The catalytic activity of the immobilized lipases in both olive oil hydrolysis and biodiesel synthesis was influenced by the particle size of PHB and lipase source. In the esterification reaction such influence was not observed. Geobacillus thermocatenulatus lipase (BTL2) was considered to be inadequate to catalyze biodiesel synthesis, but displayed high esterification activity. Butyl butyrate synthesis catalyzed by BTL2 immobilized on small PHB beads gave the highest yield (approximate to 90 mmol L-1). In biodiesel synthesis, the catalytic activity of the immobilized lipases was significantly increased in comparison to the free lipases. Full conversion of babassu oil into ethyl esters was achieved at 72 h in the presence of Pseudozyma antarctica type B (CALB), Thermomyces lanuginosus lipase (Lipex (R) 100L) immobilized on either small or large PHB beads and Pseudomonas fluorescens (PFL) immobilized on large PHB beads. The latter preparation presented the highest productivity (40.9 mg of ethyl esters mg(-1) immobilized protein h(-1)). (C) 2012 Elsevier B.V. All rights reserved.

catena-Poly[[[diaquacobalt(II)]-mu-(3,5-dinitro-2-oxidobenzoato)-kappa3O1,O2:O1'-[tetraaquacobalt(II)]-mu-(3,5-dinitro-2-oxidobenzoato)-kappa3-O1:O1',O2] dihydrate]

In the structure of polymeric title compound, {[Co2(C7H2N2O7)2(H2O)6] . 2H2O}n from the reaction of 3,5-dinitrosalicylic acid with cobalt(II) acetate, both slightly distorted octahedral Co(II) centres have crystallographic inversion symmetry. The coordination sphere about one Co centre comprises four O donors from two bidentate chelate O(phenolate), O(carboxyl) and bridging dianionic ligands and two water molecules [Co-O range, 2.0249(11)-2.1386(14)A] while that about the second Co centre has four water molecules and two bridging carboxyl O donor atoms [Co-O range, 2.0690(14)-2.1364(11)A]. The coordinated water molecules as well as the water molecules of solvation give water-water and water-carboxyl hydrogen-bonding interactions in the three-dimensional framework structure.

Poly[aqua([mu]3-2-hydroxy-5-nitrobenzoato-[kappa]3O1:O1':O2)rubidium]

In the structure of title compound [Rb2(C7H4NO2)2(H2O)2]n the centrosymmetric cyclic dimeric repeating unit comprises two irregular RbO4 complex centres bridged by the carboxylate groups of the 5-nitrosalicylate ligands. The coordination about each Rb is completed by a monodentate water molecule and a phenolic O donor which gives a bridging extension [Rb-O range 3.116(7)-3.135(5)A]. The two-dimensional polymeric structure is stabilized by intermolecular water O-H...O(carboxyl) hydrogen bonds and weak inter-ring pi--pi interactions [minimum ring centroid separation, 3.620(4)A].

Environmental degradation of lignin/poly(hydroxybutyrate) blends

Blends of lignin and poly(hydroxybutyrate) (PHB) were obtained by melt extrusion. They were buried in a garden soil for up to 12 months, and the extent and mechanism of degradation were investigated by gravimetric analysis, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and Fourier transform infra-red spectroscopy (FTIR) over the entire range of compositions. The PHB films were disintegrated and lost 45 wt% of mass within 12 months. This value dropped to 12 wt% of mass when only 10 wt% of lignin was present, suggesting that lignin both inhibited and slowed down the rate of PHB degradation. TGA and DSC indicated structural changes, within the lignin/PHB matrix, with burial time, while FTIR results confirmed the fragmentation of the PHB polymer. XPS revealed an accumulation of biofilms on the surface of buried samples, providing evidence of a biodegradation mechanism. Significant surface roughness was observed with PHB films due to microbial attack caused by both loosely and strongly associated micro-organisms. The presence of lignin in the blends may have inhibited the colonisation of the micro-organisms and caused the blends to be more resistant to microbial attack. Analysis suggested that lignin formed strong hydrogen bonds with PHB in the buried samples and it is likely that the rate of breakdown of PHB is reduced, preventing rapid degradation of the blends.