Recovery and refining of manganese as by-product from hydrometallurgical processes

The consumption of manganese is increasing, but huge amounts of manganese still end up in waste in hydrometallurgical processes. The recovery of manganese from multi-metal solutions at low concentrations may not be economical. In addition, poor iron control typically prevents the production of high purity manganese. Separation of iron from manganese can be done with chemical precipitation or solvent extraction methods. Combined carbonate precipitation with air oxidation is a feasible method to separate iron and manganese due to the fast kinetics, good controllability and economical reagents. In addition the leaching of manganese carbonate is easier and less acid consuming than that of hydroxide or sulfide precipitates. Selective iron removal with great efficiency from MnSO4 solution is achieved by combined oxygen or air oxidation and CaCO3 precipitation at pH > 5.8 and at a redox potential of > 200 mV. In order to avoid gypsum formation, soda ash should be used instead of limestone. In such case, however, extra attention needs to be paid on the reagents mole ratios in order to avoid manganese coprecipitation. After iron removal, pure MnSO4 solution was obtained by solvent extraction using organophosphorus reagents, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and bis(2,4,4- trimethylpentyl)phosphinic acid (CYANEX 272). The Mn/Ca and Mn/Mg selectivities can be increased by decreasing the temperature from the commonly used temperatures (40 –60oC) to 5oC. The extraction order of D2EHPA (Ca before Mn) at low temperature remains unchanged but the lowering of temperature causes an increase in viscosity and slower phase separation. Of these regents, CYANEX 272 is selective for Mn over Ca and, therefore, it would be the better choice if there is Ca present in solution. A three-stage Mn extraction followed by a two-stage scrubbing and two-stage sulfuric acid stripping is an effective method of producing a very pure MnSO4 intermediate solution for further processing. From the intermediate MnSO4 some special Mn- products for ion exchange applications were synthesized and studied. Three types of octahedrally coordinated manganese oxide materials as an alternative final product for manganese were chosen for synthesis: layer structured Nabirnessite, tunnel structured Mg-todorokite and K-kryptomelane. As an alternative source of pure MnSO4 intermediate, kryptomelane was synthesized by using a synthetic hydrometallurgical tailings. The results show that the studied OMS materials adsorb selectively Cu, Ni, Cd and K in the presence of Ca and Mg. It was also found that the exchange rates were reasonably high due to the small particle dimensions. Materials are stable in the studied conditions and their maximum Cu uptake capacity was 1.3 mmol/g. Competitive uptake of metals and acid was studied using equilibrium, batch kinetic and fixed-bed measurements. The experimental data was correlated with a dynamic model, which also accounts for the dissolution of the framework manganese. Manganese oxide micro-crystals were also bound onto silica to prepare a composite material having a particle size large enough to be used in column separation experiments. The MnOx/SiO2 ratio was found to affect significantly the properties of the composite. The higher the ratio, the lower is the specific surface area, the pore volume and the pore size. On the other hand, higher amount of silica binder gives composites better mechanical properties. Birnesite and todorokite can be aggregated successfully with colloidal silica at pH 4 and with MnO2/SiO2 weight ratio of 0.7. The best gelation and drying temperature was 110oC and sufficiently strong composites were obtained by additional heat-treatment at 250oC for 2 h. The results show that silica–supported MnO2 materials can be utilized to separate copper from nickel and cadmium. The behavior of the composites can be explained reasonably well with the presented model and the parameters estimated from the data of the unsupported oxides. The metal uptake capacities of the prepared materials were quite small. For example, the final copper loading was 0.14 mmol/gMnO2. According to the results the special MnO2 materials are potential for a specific environmental application to uptake harmful metal ions.

Operational characteristics of four metering systems for agricultural fertilizers and amendments

The use of fertilizers and solid amendments in agriculture generates special interest for their effect on crop productivity, as well as for their environmental impact. The efficient use of these products demands knowing their physical and mechanical properties, the storing conditions effect and the operational characteristics of the metering systems used in the fertilizing equipment. In this context, the present study was developed with the purpose of evaluating the operational characteristics of different fertilizing metering systems and to determine the adequate metering system-product operational parameters, using powder lime, powder gypsum, granular 10-30-10 (N-P-K), and granular urea. Operational differences were established among four types of commercial fertilizer metering systems, including wire auger, star-shaped feed wheel, feed screw and ridged traction wheel. The study found that the unloading rate depends directly on the fertilizer metering system's rotating speed and is affected by particle size, repose angle, bulk density and moisture content of the applied product. The wire auger and star-shaped feed wheel metering systems were adequate for the distribution of powder products and the feed screw for granulated fertilizers. Furthermore, theoretical and experimental characteristic equations were established, defining curves for calibration and handling of the products plus the rotating speed range in which a better distributing behavior was achieved.

Mathematical analysis of maximum power generated by photovoltaic systems and fitting curves for standard test conditions

The rural electrification is characterized by geographical dispersion of the population, low consumption, high investment by consumers and high cost. Moreover, solar radiation constitutes an inexhaustible source of energy and in its conversion into electricity photovoltaic panels are used. In this study, equations were adjusted to field conditions presented by the manufacturer for current and power of small photovoltaic systems. The mathematical analysis was performed on the photovoltaic rural system I-100 from ISOFOTON, with power 300 Wp, located at the Experimental Farm Lageado of FCA/UNESP. For the development of such equations, the circuitry of photovoltaic cells has been studied to apply iterative numerical methods for the determination of electrical parameters and possible errors in the appropriate equations in the literature to reality. Therefore, a simulation of a photovoltaic panel was proposed through mathematical equations that were adjusted according to the data of local radiation. The results have presented equations that provide real answers to the user and may assist in the design of these systems, once calculated that the maximum power limit ensures a supply of energy generated. This real sizing helps establishing the possible applications of solar energy to the rural producer and informing the real possibilities of generating electricity from the sun.

Yield of cotton/cowpea and sunflower/cowpea crop rotation systems during the reclamation process of a saline-sodic soil

The objective of this study was to evaluate the use of subsoiling, gypsum and organic matter associated with the cultivation of cotton, sunflower and cowpea in crop rotation, seeking the reclamation and use of a saline-sodic soil. The treatments were arranged in a randomized block design in split plots with four replications, during two crop cycles (2009/2010 and 2010/2011). The plots were formed by the treatments: T1. Subsoiling (S); T2. S + 20 Mg ha-1 of gypsum; T3. S + 40 Mg ha-1 of organic matter; T4. S + 10 Mg ha-1 of gypsum + 20 Mg ha-1 of organic matter; T5. S + 20 Mg ha-1 of gypsum + 40 Mg ha-1 of organic matter and the sub-plots consisted of the cotton-cowpea (C/CP) and sunflower-cowpea (S/CP) crop rotation. The use of gypsum and organic matter contributed to decrease the soil salinity and sodicity. Cotton was not affected by the treatments, while the sunflower crop was favored by the application of amendments only in the second production cycle. Higher yields of cowpea in T5 treatment, during the 2009/2010 cycle, are indicative that higher doses of gypsum and organic matter applied in this treatment accelerate the reclamation process. For other treatments with amendment application there was a beneficial effect for this crop only in the second cycle, when the values of productivity were similar to T5.

Internal ambience of beehives Apis mellifera with different colors and roofing materials in the sub middle of the São Francisco Valley

ABSTRACTThe current study aimed to evaluate the influence of three colors and two types of roofing materials under the internal temperature of bee colonies Apis mellifera. The experiment was conducted at the Agricultural Sciences Campus at the Federal University of Sao Francisco Valley located in Petrolina-PE, in November and December 2013, using 24 colonies housed in Langstroth hives. The experiment was a completely randomized factorial design (3x2) with three colors of box (blue, white, and traditional) and two types of cover (with and without the use of plaster) with six treatments and four replications. The internal temperature dates of the colonies were hourly recorded, during 24 hours, and surface temperatures were hourly recorded between 08h00 and 17h00. The highest values for surface and internal temperature were registered in the blue painted boxes without the use of plasterboard, and the blue painted boxes covered with plasterboard respectively. However, the lowest values ​​were found in the white painted hives and hives that have not received the plasterboard. It is recommended to paint boxes with bright colors, and the use of plasterboard had no effect in reducing the internal temperature.

Free Prostate-specific Antigen Forms and Kallikrein-related Peptidase 2: Tools for Prostate Cancer Diagnostics

Prostate-specific antigen (PSA) is a marker that is commonly used in estimating prostate cancer risk. Prostate cancer is usually a slowly progressing disease, which might not cause any symptoms whatsoever. Nevertheless, some cases of cancer are aggressive and need to be treated before they become life-threatening. However, the blood PSA concentration may rise also in benign prostate diseases and using a single total PSA (tPSA) measurement to guide the decision on further examinations leads to many unnecessary biopsies, over-detection, and overtreatment of indolent cancers which would not require treatment. Therefore, there is a need for markers that would better separate cancer from benign disorders, and would also predict cancer aggressiveness. The aim of this study was to evaluate whether intact and nicked forms of free PSA (fPSA-I and fPSA-N) or human kallikrein-related peptidase 2 (hK2) could serve as new tools in estimating prostate cancer risk. First, the immunoassays for fPSA-I and free and total hK2 were optimized so that they would be less prone to assay interference caused by interfering factors present in some blood samples. The optimized assays were shown to work well and were used to study the marker concentrations in the clinical sample panels. The marker levels were measured from preoperative blood samples of prostate cancer patients scheduled for radical prostatectomy. The association of the markers with the cancer stage and grade was studied. It was found that among all tested markers and their combinations especially the ratio of fPSA-N to tPSA and ratio of free PSA (fPSA) to tPSA were associated with both cancer stage and grade. They might be useful in predicting the cancer aggressiveness, but further follow-up studies are necessary to fully evaluate the significance of the markers in this clinical setting. The markers tPSA, fPSA, fPSA-I and hK2 were combined in a statistical model which was previously shown to be able to reduce unnecessary biopsies when applied to large screening cohorts of men with elevated tPSA. The discriminative accuracy of this model was compared to models based on established clinical predictors in reference to biopsy outcome. The kallikrein model and the calculated fPSA-N concentrations (fPSA minus fPSA-I) correlated with the prostate volume and the model, when compared to the clinical models, predicted prostate cancer in biopsy equally well. Hence, the measurement of kallikreins in a blood sample could be used to replace the volume measurement which is time-consuming, needs instrumentation and skilled personnel and is an uncomfortable procedure. Overall, the model could simplify the estimation of prostate cancer risk. Finally, as the fPSA-N seems to be an interesting new marker, a direct immunoassay for measuring fPSA-N concentrations was developed. The analytical performance was acceptable, but the rather complicated assay protocol needs to be improved until it can be used for measuring large sample panels.

Sähkön tuotantokustannusvertailu

Työssä vertaillaan eri sähköntuotantovaihtoehtojen taloudellista kannattavuutta. Kannattavuusvertailu suoritetaan pelkkää sähköä tuottaville voimalaitoksille. Raportti on jatkoa aikaisemmille tutkimuksille, joista viimeisin julkaistiin 2008. Tutkittavat voimalaitostyypit ovat: ydinvoimalaitos, maakaasukombilauhdevoimalaitos, kivihiililauhdevoimalaitos, turvelauhdevoimalaitos, puulauhdevoimalaitos, tuulivoimala ja uutena aurinkovoimala. Kannattavuustarkastelu suoritetaan annuiteettimenetelmällä käyttäen 5 % reaalikorkoa ja maaliskuun 2012 hintatasoa. Laskelmien perusteella 8000 tunnin huipunkäyttöajalla ydinsähkön tuotantokustannus, kun laitos rakennetaan olemassaolevalle tontille olisi 43,7 €/MWh, täysin uuden ydinvoimalaitoksen 57,9 €/MWh, kaasusähkön 75,4 €/MWh, turvelauhteen 75,4 €/MWh ja hiilisähkön hiilidioksidin talteenotolla 64,4 €/MWh, kun hiilidioksidipäästöoikeuden hintana käytetään 23 €/t. Vastaavasti uusiutuvista puupolttoainelauhdesähkön tuotantokustannus olisi 70,2 €/MWh kun taas 2200 tunnin huipunkäyttöajalla maalla sijaitsevan tuulivoimalaitoksen sähkön tuotantokustannus 52,7 €/MWh ja merellä sijaitsevan tuulivoimalaitoksen 76,8 €/MWh. Erillistarkastelussa arvioitiin suurien keskittävää teknologiaa käyttävän aurinko-voimalaitoksen tuotantokustannuksen ylittävän 100 €/MWh ollen todennäköisesti lähempänä 150 €/MWh. Arvio piensähkön tuotantokustannuksista aurinkosähköisillä paneeleilla vaihtelee 90 – 130 €/MWh. Merkittävin kustannussäästö syntyy, jos aurinkosähköpaketteja voidaan tarjota kuluttajalle kokonaistoimituksena avaimet käteen. Aurinkosähkön tuottaminen kotikeräimillä näyttääkin olevan vaiheessa, jossa se on selkeästi pienkäyttäjälle edullista mikäli sijoitettava pääoma 6000 – 18000 € ei vaadi ulkopuolista rahoitusta.

Early screening for preeclampsia

Preeclampsia, which affects about 3 to 5% of pregnant women, is the most frequent medical complication in pregnancy and the most important cause of maternal and perinatal morbidity and mortality. During the past three decades, numerous clinical, biophysical, and biochemical screening tests have been proposed for the early detection of preeclampsia. Literature shows large discrepancies in the sensitivity and predictive value of several of these tests. No single screening test used for preeclampsia prediction has gained widespread acceptance into clinical practice. Instead, its value seems to be in increasing the predictive value of panels of tests, which include other clinical measurements. The aim of this review was to examine the combination of maternal risk factors, mean arterial blood pressure, and uterine artery Doppler, together with biomarkers in the preeclampsia prediction.

Introduction of the T-10 static line parachuting capability to the NH90 helicopter

The purpose of this study was to investigate the suitability of the Finnish Defence Forces’ NH90 helicopter for parachuting operations with the T-10 static line parachute system. The work was based on the Army Command’s need to compensate for the reduction in the outsourced flight hours for the military static line parachuting training. The aim of the research was to find out the procedures and limitations with which the NH90 IOC+ or FOC version helicopter could be used for static line parachutist training with the T-10B/MC1-1C parachutes. The research area was highly complicated and non-linear. Thus analytical methods could not be applied with sufficient confidence, even with present-day computing power. Therefore an empirical research method was selected, concentrating on flight testing supported with literature study and some calculated estimations. During three flights and 4.5 flight hours in Utti, Finland on 1720 September 2012, a total of 44 parachute drops were made. These consisted of 16 dummy drops and 28 paratrooper jumps. The test results showed that when equipped with the floor mounted PASI-1 anchor line, the deflector bar of the NHIndustries’ Parachuting Kit and Patria’s floor protection panels the Finnish NH90 variant could be safely used for T-10B/MC1-1C static line parachuting operations from the right cabin door at airspeed range of 5080 KIAS (90–150 km/h). The ceiling mounted anchor lines of the NHI’s Parachuting Kit were not usable with the T-10 system. This was due to the static lines’ unsafe behaviour in slipstream when connected to the cabin ceiling level. In conclusion, the NH90 helicopter can be used to meet the Army Command’s requirement for an additional platform for T-10 static line parachutist training. Material dropping, the effect of additional equipment and jumping from the rear ramp should be further studied.

Lead poisoning in cattle and chickens in the state of Pará, Brazil

The present study describes the occurrence of lead poisoning in cattle and chickens in Pará, Brazil. In a lot composed of 80 calves from a dairy herd, 10 animals became sick and nine died, but one animal recovered after being removed from the paddock. Upon inspection of this paddock, the presence of truck batteries used to store energy captured by solar panels was found. The clinical signs observed in calves included difficult breathing, nasal discharge, excessive salivation, corneal opacity, pushing of the head against objects and recumbency. The chickens had decreased oviposition and produced eggs with thin or malformed shells. The necropsy findings of the cattle, as well as the histopathological changes observed, were of little significance except for one animal that showed mild astrocytosis histopathology in the cerebral cortex. In one of the chickens, renal histopathology showed mild multifocal acute tubular necrosis. The mean lead concentrations in the livers and kidneys of the cattle were 93.91mg/kg and 209.76mg/kg, respectively, and the mean concentration detected in chicken livers was 105.02mg/kg. It was concluded that the source of lead poisoning in these calves and chickens were the truck battery plates, which were within reach of the animals.

Development of porous glass-fiber reinforced composite for bone implants. Evaluation of antimicrobial effect and implant fixation

Cranial bone reconstructions are necessary for correcting large skull bone defects due to trauma, tumors, infections and craniotomies. Traditional synthetic implant materials include solid or mesh titanium, various plastics and ceramics. Recently, biostable glass-fiber reinforced composites (FRC), which are based on bifunctional methacrylate resin, were introduced as novel implant solution. FRCs were originally developed and clinically used in dental applications. As a result of further in vitro and in vivo testing, these composites were also approved for clinical use in cranial surgery. To date, reconstructions of large bone defects were performed in 35 patients. This thesis is dedicated to the development of a novel FRC-based implant for cranial reconstructions. The proposed multi-component implant consists of three main parts: (i) porous FRC structure; (ii) bioactive glass granules embedded between FRC layers and (iii) a silver-polysaccharide nanocomposite coating. The porosity of the FRC structure should allow bone ingrowth. Bioactive glass as an osteopromotive material is expected to stimulate the formation of new bone. The polysaccharide coating is expected to prevent bacterial colonization of the implant. The FRC implants developed in this study are based on the porous network of randomly-oriented E-glass fibers bound together by non-resorbable photopolymerizable methacrylate resin. These structures had a total porosity of 10–70 volume %, of which > 70% were open pores. The pore sizes > 100 μm were in the biologically-relevant range (50-400 μm), which is essential for vascularization and bone ingrowth. Bone ingrowth into these structures was simulated by imbedding of porous FRC specimens in gypsum. Results of push-out tests indicated the increase in the shear strength and fracture toughness of the interface with the increase in the total porosity of FRC specimens. The osteopromotive effect of bioactive glass is based on its dissolution in the physiological environment. Here, calcium and phosphate ions, released from the glass, precipitated on the glass surface and its proximity (the FRC) and formed bone-like apatite. The biomineralization of the FRC structure, due to the bioactive glass reactions, was studied in Simulated Body Fluid (SBF) in static and dynamic conditions. An antimicrobial, non-cytotoxic polysaccharide coating, containing silver nanoparticles, was obtained through strong electrostatic interactions with the surface of FRC. In in vitro conditions the lactose-modified chitosan (chitlac) coating showed no signs of degradation within seven days of exposure to lysozyme or one day to hydrogen peroxide (H2O2). The antimicrobial efficacy of the coating was tested against Staphylococcus aureus and Pseudomonas aeruginosa. The contact-active coating had an excellent short time antimicrobial effect. The coating neither affected the initial adhesion of microorganisms to the implant surface nor the biofilm formation after 24 h and 72 h of incubation. Silver ions released to the aqueous environment led to a reduction of bacterial growth in the culture medium.

Toimintaohjeistus HSY:n jätteenpolton materiaalivirtojen hallintaan

Vantaan Energia rakentaa ympäristövaatimukset täyttävän jätevoimalan Itä-Vantaan Långmossebergeniin. Jätevoimalassa tullaan käyttämään polttoaineena kierrätykseen kelpaamatonta syntypaikkalajiteltua yhdyskuntajätettä sekä maakaasua. Helsingin seudun ympäristöpalvelut -kuntayhtymä HSY tulee toimittamaan noin 80 % vuosittaisesta jätepolttoaineesta. Tässä työssä on esitetty toimintamalli HSY:n jätteenpolton materiaalivirtojen hallitsemiseksi. Toimintamallin tarkoituksena on antaa ohjeistus jätteiden materiaalivirtojen käsittelymenetelmistä ennen jätteenpolttolaitosta. Lisäksi toimintamallin tarkoituksena on saada vähennettyä pohjakuonan määrää. Toimintamalli sisältää ohjeistuksen kotitalouksien sekajätteen, pienjäteasemien sekajätteen, sekalaisen rakennus- ja purkujätteen sekä kaupan- ja teollisuuden jätteiden käsittelytavoista. Jätevirtojen koostumusta on selvitetty kirjallisuudesta löytyvien tietojen perusteella ja tietoja on täydennetty kesällä 2013 suoritetun lajittelututkimuksen tiedoilla. Tutkimuksen tuloksista selvisi, että pienjäteasemien sekajätteiden lajittelua tehostamalla HSY:llä pystytään tekemään merkittäviä taloudellisia säästöjä. Tutkimuksessa selvisi, että kipsilevy olisi kannattavinta kerätä omalle lavalleen pienjäteasemilla. Sekalaisen rakennus- ja purkujätteen osalta todettiin, että sitä ei kannata ohjata suoraan jätevoimalalle poltettavaksi, eikä sitä voida sijoittaa käsittelemättömänä kaatopaikalle vuoden 2020 jälkeen. Tästä syystä työssä on ehdotettu, että sekalainen rakennus- ja purkujäte ohjattaisiin lajittelulaitokselle käsiteltäväksi ennen sen loppusijoittamista. Tutkimuksen tulosten perusteella voidaan myös todeta, että toimintamallia noudattamalla, pohjakuonan määrää on mahdollista vähentää lähes puolella alkuperäisestä arviosta.

Puolueiden keskustelutilaisuuksista mediatapahtumiksi. Television vaaliohjelmat ja niihin liittynyt sanomalehtijulkisuus 1960-luvulta 1980-luvulle

Tässä tutkimuksessa tarkastellaan television vaaliohjelmia ja niihin liittynyttä sanomalehtijulkisuutta 1960-luvun alusta 1980-luvun lopulle. Tarkastelun kohteena ovat sekä eduskunta- että presidentinvaalien vaaliohjelmat. Tutkimusaineisto koostuu Yleisradion hallinto- ja ohjelmaneuvostojen pöytäkirjoista, vaaliohjelmien televisiotallenteista sekä vaaliohjelmia käsittelevistä sanomalehtikirjoituksista. Lehtiaineisto on kerätty Helsingin Sanomista, Ilta-Sanomista, Iltalehdestä, Aamulehdestä, Kansan Uutisista, Suomenmaasta sekä Suomen Sosialidemokraatista. Sanomalehtiaineistoa on täydennetty Yleisradion leikearkistoon kerätyillä lehtileikkeillä. Tutkimuksessa on analysoitu toisaalta television vaaliohjelmien kehitystä ja toisaalta vaaliohjelmiin liittynyttä sanomalehtikirjoittelua. Television vaaliohjelmien kehityksen osalta tutkimuksessa on kuvattu, millä tavoin vaaliohjelmia on eri aikoina tehty ja millaisia poliittisia kiistoja niiden tekemiseen on liittynyt. Sanomalehtiaineiston analyysissa on tarkasteltu sitä, mihin seikkoihin vaaliohjelmia käsittelevissä kirjoituksissa on kiinnitetty huomiota, millä tavoin lehdet ovat suhtautuneet ohjelmien toteutukseen ja millainen rooli ohjelmilla on nähty olleen vaalikampanjoinnissa. Väitöskirjan näkökulma on historiallinen, mikä merkitsee ajallisten kontekstien keskeisyyttä analyysissa. Tutkimuksessa on kiinnitetty huomiota sekä poliittisessa kulttuurissa että mediamaisemassa tapahtuneisiin muutoksiin. Vaaliohjelmat olivat 1960-luvulla tarkkaan säänneltyjä puolueiden välisiä keskustelutilaisuuksia, joissa toimittajilla ei ollut näkyvää roolia. Ohjelmien toteutuksesta vastasivat puoluemandaateilla toimineet Yleisradion ohjelma- ja hallintoneuvoston jäsenet, joten ohjelmien toteutuksen yksityiskohdista vastasivat puolueet. Puolueet riitelivät usein vaaliohjelmien toteutuksesta, mikä osoittaa, että puolueille television vaaliohjelmat olivat tärkeitä poliittisia foorumeita jo 1960-luvulta lähtien. Vaaliohjelmat jakautuivat kahteen erilaiseen ohjelmaformaattiin; vaalitentteihin ja suureen vaalikeskusteluun. Vaalitenteissä kunkin puolueen edustajat olivat vuorollaan ”altavastaajina”, joille muiden puolueiden edustajat esittivät kysymyksiä. Suuri vaalikeskustelu oli perinteisempi paneelikeskustelu, jossa poliitikot selvittivät vuorotellen kantojaan ajankohtaisiin poliittisin kysymyksiin. 1970-luvun puolivälissä vaalitenttien toteutuksessa tapahtui suuria muutoksia, kun toimittajat syrjäyttivät poliitikot vaalitenttien kyselijöinä. Suuri vaalikeskustelu säilyi ennallaan. Sanomalehtien suhtautuminen vaaliohjelmiin oli 1960- ja 1970-luvuilla huomattavasti pidättyvämpää kuin poliitikkojen. Sanomalehdistön näkökulmasta television vaaliohjelmien tärkeimpänä tehtävänä oli puolueiden poliittisten linjausten esittely. Vaaliohjelmia käsittelevissä teksteissä esiteltiin pääasiassa poliitikkojen ohjelmissa pitämiä puheenvuoroja. Puoluelehdissä puheenvuorojen sisältöä arvioitiin aatteellisista lähtökohdista, sitoutumattomissa sanomalehdissä neutraalimmin. Vaaliohjelmien toteutukseen liittynyt kritiikki kohdistui toisaalta poliitikkojen puoluepropagandaan, toisaalta poliitikkojen liialliseen varovaisuuteen. Sanomalehtien suhtautuminen vaaliohjelmiin säilyi ennallaan myös 1970-luvulla, jolloin vaaliohjelmia alettiin tehdä toimittajavetoisesti. Ainoa muutos liittyi vaaliohjelmakritiikkiin, joka kohdistui nyt poliitikkojen ohella myös toimittajiin, joiden katsottiin olleen ohjelmissa liian hyökkääviä. Suurin muutos vaaliohjelmiin liittyneessä kirjoittelussa tapahtui 1980-luvulla. Vaaliohjelmia käsitteleviä kirjoituksia julkaistiin sanomalehdistössä monikertainen määrä 1970-lukuun verrattuna. Samalla myös vaaliohjelmia käsittelevien kirjoitusten näkökulmat alkoivat muuttua, kun ohjelmin visuaalinen ulottuvuus alkoi olla yhä näkyvämmin esillä sanomalehtiin laadituissa analyyseissa. Lehdet alkoivat teettää säännöllisesti erilaisia tutkimuksia poliitikkojen pärjäämisestä ohjelmissa ja kirjoittaa vaalikeskusteluiden voittajista ja häviäjistä. Lisäksi lehtijutuissa arvioitiin poliitikkojen esiintymistä ja vaaliohjelmista välittyviä vaikutelmia. Vuoden 1982 presidentinvaaleissa uusista näkökulmista kirjoittivat erityisesti iltapäivälehdet, mutta vuosikymmenen jälkipuoliskolla samankaltaisia lähestymistapoja omaksuivat myös Helsingin Sanomat ja Aamulehti. Niiden vaaliohjelmia käsittelevissä uutisissa kiinnitettiin yhä useammin huomiota poliitikkojen esiintymiseen, pukeutumiseen ja tunnetiloihin. Puoluelehtien suhtautuminen vaaliohjelmiin säilyi kuitenkin ennallaan, ja myös vaaliohjelmakritiikki säilyi suurelta osin muuttumattomana. 1980-luvun aikana television vaaliohjelmat muuttuivat lehdistön käsittelyssä puolueiden tavoitteita esittelevistä keskustelutilaisuuksista poliitikkojen ja puolue johtajien henkilökohtaisia ominaisuuksia mittaaviksi esiintymiskokeiksi ja suuriksi mediatapahtumiksi, joiden katsottiin toisinaan jopa ratkaisseen vaalin tuloksen. Nostaessaan television vaaliohjelmat kampanjajournalisminsa ytimeen, sanomalehdet vahvistivat television poliittista roolia.

Introduction of the T-10 static line parachuting capability to the NH90 helicopter

The purpose of this study was to investigate the suitability of the Finnish Defence Forces’ NH90 helicopter for parachuting operations with the T-10 static line parachute system. The work was based on the Army Command’s need to compensate for the reduction in the outsourced flight hours for the military static line parachuting training. The aim of the research was to find out the procedures and limitations with which the NH90 IOC+ or FOC version helicopter could be used for static line parachutist training with the T- 10B/MC1-1C parachutes. The research area was highly complicated and non-linear. Thus analytical methods could not be applied with sufficient confidence, even with present-day computing power. Therefore an empirical research method was selected, concentrating on flight testing supported with literature study and some calculated estimations. During three flights and 4.5 flight hours in Utti, Finland on 17−20 September 2012, a total of 44 parachute drops were made. These consisted of 16 dummy drops and 28 paratrooper jumps. The test results showed that when equipped with the floor mounted PASI-1 anchor line, the deflector bar of the NHIndustries’ Parachuting Kit and Patria’s floor protection panels the Finnish NH90 variant could be safely used for T-10B/MC1-1C static line parachuting operations from the right cabin door at airspeed range of 50−80 KIAS (∼90–150 km/h). The ceiling mounted anchor lines of the NHI’s Parachuting Kit were not usable with the T-10 system. This was due to the static lines’ unsafe behaviour in slipstream when connected to the cabin ceiling level. In conclusion, the NH90 helicopter can be used to meet the Army Command’s requirement for an additional platform for T-10 static line parachutist training. Material dropping, the effect of additional equipment and jumping from the rear ramp should be further studied.

Working towards the invisible repository

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014