Performance evaluation of hydrocyclone filter for microirrigation

In this study a hydrocyclone filter of 20 cm was selected and its performance was evaluated by studying the variation of discharge, pressure drop, influent concentration, and filtration efficiency with elapsed time of operation. The filter was tested with clean water to determine clean pressure drop and later it was tested with four concentrations of solid suspension, viz. 300; 600; 900 and 1,200 mg L-1. In the concentration of 300 mg L-1, the variation of pressure drop was low. But for the other concentrations of solid suspension, the variation was significant. The maximum pressure drops obtained were 41.19, 45.11, 50.01 and 52.95 kPa at 350, 390, 280 and 190 minutes of elapsed time, respectively. The maximum efficiency of solid suspension was 30.3, 32.96, 43.89 and 52.5% where as the minimum efficiencies were 9.91, 9.93, 9.62 and 9.9%, respectively. The hydrociclone tested presented inefficiency to filter small particles as clay. The initial removal efficiency of higher concentration was bigger than for lower concentration but, the final efficiency are almost the same irrespective of the concentration of solid suspension. The present tested hydrocyclone could be used as a pre-filter microirrigation to prevent emitter clogging.

Performance of spray nozzles in land applications with high speed

The aim of this study was to evaluate different spray nozzles for land applications in high speed on the coverage and deposit in soybean plants pulverization. It was evaluated the AXI 110 04 plane jet nozzles operated at speed of 4.17m.s-1 (control), the grey APE and the AXI 110 08 plane jets, and the TD HiSpeed 110 06 and AXI TWIN 120 06 twin jets, at speed of 9.72m.s-1. The application volume was fixed in 120L ha-1. The application efficiency was evaluated by two different methods: analysis of the coverage area using fluorescent pigment and UV light and analysis of deposits through the recovery and quantification of FD&C N°1 brilliant blue marker by spectrophotometry. Both analyses were done in samples collected from top, middle and bottom parts of the plants. The spray nozzles showed differences in coverage and deposit pattern, so in the top part, the coverage was increased with smaller drops and the deposits were increased with medium drops. In the other parts of the plants, there were no statistical differences between the treatments for both coverage and deposits. The displacement speed did not influence the application efficiency for nozzles with the same drop pattern, and the obtained spray coverage and deposits at the medium and bottom parts of the plants were less than 50% of that found at the top of the soybean plants.

Potential of adjuvants to reduce drift in agricultural spraying

The reduction of pesticide spraying drift is still one of the major challenges in Brazilian agriculture. The aim of this study was to evaluate the potential of different adjuvant products, such as surfactants, drift retardants, mineral oil and vegetable oil for reducing drift in agricultural spraying. The experiment consisted of quantifying drift of sprayings of 18 adjuvants dissolved in water under controlled conditions in a wind tunnel. Tests were performed in triplicates with spraying nozzles type Teejet XR8003 VK, pressure of 200kPa and medium drops. Solutions sprayed were marked with Brilliant Blue dye at 0.6% (m v-1). The drift was collected using polyethylene strips transversally fixed along the tunnel at different distances from the nozzle and different heights from the bottom part of the tunnel. Drift deposits were evaluated by spectrophotometry in order to quantify deposits. The adjuvants from chemical groups of mineral oil and drift retardant resulted in lower values of drift in comparison with surfactants and water. The results obtained in laboratory show that the selection of appropriate class and concentration of adjuvants can significantly decrease the risk of drift in agricultural spraying. However, the best results obtained in laboratory should be validated with pesticide under field conditions in the future.

Vuosihuollon aikainen käyttöturvallisuus

Tässä työssä on tarkasteltu Suomessa käytössä olevien ydinvoimalaitosten vuosihuoltojen aikaista käyttöturvallisuutta yleisesti sekä arvioitu voimayhtiöiden vuosihuoltojen aikaisten häiriö- ja hätätilanteiden varalta laatimien ohjeiden kattavuutta. Kattavuuden arviointi suoritettiin tarkastelemalla seisokkitiloja käsitteleviä todennäköisyysperusteista riskianalyysia (PRA), lopullista turvallisuusselostetta (FSAR) ja turvallisuusteknisiä käyttöehtoja (TTKE). PRA:n mukaan Olkiluodon 1 ja 2 laitosyksiköiden sydänvauriotaajuudesta noin 25 % liittyy vuosihuollon aikaisiin alkutapahtumiin. Loviisan laitosyksiköillä vastaava osuus on noin 61 %. Merkittävimmät vuosihuoltojen aikaiset alkutapahtumat sydänvaurioriskin kannalta olivat Olkiluodossa tulipalot, jäähdytteen menetykset ja jälkilämmön poiston menetykset sekä Loviisassa raskaan taakan pudotukset, booripitoisuuden laimeneminen ja öljyonnettomuudet. Saatujen tulosten perusteella voitiin todeta, että voimayhtiöiden laatimat häiriö- ja hätätilanneohjeet olivat pääosiltaan asianmukaiset ja ne kattoivat hyvin erilaiset seisokin aikaiset alkutapahtumat. Tarkastelun perusteella tehtiin ohjeistoon muutamia parannusehdotuksia. Seisokkitiloja koskevat TTKE ja FSAR havaittiin asianmukaisiksi molemmilla tarkastelluilla laitoksilla.

Epidemiological survey on Mycoplasma gallisepticum and M. synoviae by multiplex PCR in commercial poultry

Mycoplasmas are important avian pathogens, which cause respiratory and joint diseases that result in large economic losses in Brazilian and world-wide poultry industry. This investigation regarding the main species of mycoplasmas, Mycoplasma gallisepticum (MG) and M. synoviae (MS), responsible for the above mentioned conditions, was carried out through PCR Multiplex analysis. One thousand and forty-six (1,046) samples of tracheal swabs and piped embryos were collected from 33 farms with laying hens, breeders, broilers or hatchery, located in the Brazilian states of São Paulo, Paraná and Pernambuco, where respiratory problems or drops in egg production had occurred. The MG and MS prevalence on the farms was 72.7%. These results indicated (1) high dissemination of mycoplasmas in the evaluated farms, with predominance of MS, either as single infectious agent or associated with other mycoplasmas in 20 farms (60.6%), and (2) an increase of MS and decrease of MG infection in Brazilian commercial poultry.

Retrospective study on clinical management of indolent ulcers in Boxer dogs

Indolent ulcers are superficial corneal ulcers secondary to several changes on the corneal surface. They are frequently observed in middle-aged Boxer dogs, cause pain of acute onset and requires appropriate treatment. Aiming to evaluate the efficacy of clinical managements on the rate of healing of indolent ulcers, a retrospective study was conducted (1997-2008). Results demonstrated that proteinase inhibitors were the most often prescribed medication, and its administration did not interfere on the healing rate, as well as observed in dogs that received 1% atropine, antibiotics and anti-inflammatory drugs. Healing was delayed in dogs administered orally with vitamin C, but the healing process was faster on those dogs that went through corneal debridement/cauterization. In conclusion, to know the various types of treatments seems to be fundamental for the rapid resolution of the disease. It is suggested that debridement/cauterization, administration of proteinase inhibitor eye drops, prophylactic topical antibiotics and oral vitamin C, should be considered as an effective clinical management for indolent ulcers in Boxer dogs.

Spinal cord compression in cattle after the use of an oily vaccine

An outbreak of compressive myelopathy in cattle associated with the improper use of an oil vaccine is described. Neurological signs were observed in 25 out of 3,000 cattle after 60 days of being vaccinated against foot and mouth disease. The clinical picture was characterized by progressive paralysis of the hind limbs, difficulty in standing up, and sternal recumbency during the course of 2-5 months. A filling defect between the L1 and L3 vertebrae was seen through myelography performed in one of the affected animals. A yellow-gray, granular and irregular mass was observed in four necropsied animals involving the spinal nerve roots and epidural space of the lumbar (L1-L4) spinal cord; the mass was associated with a whitish oily fluid. This fluid was also found in association with necrosis of the longissimus dorsi muscle. Microscopic changes in the epidural space, nerve roots, and spinal musculature were similar and consisted of granulomas or pyogranulomas around circular unstained spaces (vacuoles). These spaces were located between areas of severe diffuse hyaline necrosis of muscle fibers and resembled the drops of oil present in the vaccine.

Introduction of the T-10 static line parachuting capability to the NH90 helicopter

The purpose of this study was to investigate the suitability of the Finnish Defence Forces’ NH90 helicopter for parachuting operations with the T-10 static line parachute system. The work was based on the Army Command’s need to compensate for the reduction in the outsourced flight hours for the military static line parachuting training. The aim of the research was to find out the procedures and limitations with which the NH90 IOC+ or FOC version helicopter could be used for static line parachutist training with the T-10B/MC1-1C parachutes. The research area was highly complicated and non-linear. Thus analytical methods could not be applied with sufficient confidence, even with present-day computing power. Therefore an empirical research method was selected, concentrating on flight testing supported with literature study and some calculated estimations. During three flights and 4.5 flight hours in Utti, Finland on 1720 September 2012, a total of 44 parachute drops were made. These consisted of 16 dummy drops and 28 paratrooper jumps. The test results showed that when equipped with the floor mounted PASI-1 anchor line, the deflector bar of the NHIndustries’ Parachuting Kit and Patria’s floor protection panels the Finnish NH90 variant could be safely used for T-10B/MC1-1C static line parachuting operations from the right cabin door at airspeed range of 5080 KIAS (90–150 km/h). The ceiling mounted anchor lines of the NHI’s Parachuting Kit were not usable with the T-10 system. This was due to the static lines’ unsafe behaviour in slipstream when connected to the cabin ceiling level. In conclusion, the NH90 helicopter can be used to meet the Army Command’s requirement for an additional platform for T-10 static line parachutist training. Material dropping, the effect of additional equipment and jumping from the rear ramp should be further studied.

The seasonal and ovarian status effects on in vitro production of domestic cat embryos between Equator and Tropic of Capricorn

From the Tropic of Capricorn to Equator, the seasonality of domestic cat is known to be absent, i.e., these animals are considered non-seasonal breeders at these regions. We hypothesized that this particularity might have some influence on in vitro embryo production. The aim of this experiment was to determine the percentage of cleavage and morulae and blastocyst formation produced from oocytes recovered from queen ovaries of three distinct status - follicular, luteal or inactive - during two different reproductive seasons experienced by cats in southeast of Brazil (22°53'09" S and 48°26'42" W) - non breeding season (NBS), comprehending January to March; and breeding season (BS), August to October. Thirty queens were neutered. Ovaries were classified according to their status and were sliced in PBS for cumulus oocyte complex (COC) releasing. Grade I COC were washed three times in H-MEM supplemented with BSA, glutamine, sodium pyruvate, cysteine, streptomycin and penicillin. Oocytes were incubated in groups of 20-30 in 400µL of DMEM supplemented with FSH, LH, estradiol, IGF-I and basic fibroblast growth factor under mineral oil for 30 or 36 hours at 38°C in humidified environment of 5% de O2, 5% CO2 and 90% N2. COC were fertilized in Ham's F-10 medium supplemented with BSA, cysteine, pyruvate and streptomycin/penicillin (culture medium) with fresh semen selected through swim up technique. Eighteen hours later, the presumptive zygotes were denuded, the percentage of cleavage was determined and every 10 zygotes were transferred to 100mL drops of culture medium for culture during three days. After 72 hours of culture the percentage of morulae formation was evaluated and these structures were transferred to drops of the same culture medium. At the eighth day of culture blastocyst formation was analyzed. During NBS, from a total of 272 (inactive), 162 (luteal) and 134 (follicular) fertilized oocytes, the percentage of cleaved zygotes, morulae and blastocysts derived from inactive ovaries were 24.63, 16.54 and 8.09 respectively; for those derived from luteal ovaries, the percentage was 21.6, 12.96 and 8.64, and for those from follicular ovaries, they were 24.62, 16.41 and 8.21. Considering BS, from a total of 102 (inactive), 198 (luteal) and 86 (follicular) fertilized oocytes, the relative frequency (%) of cleaved zygotes, morulae and blastocysts derived from inactive ovaries were 64.7, 41.17 and 23.53 respectively; for those derived from luteal ovaries, the percentage was 64.14, 40.41 and 23.73, and for those from follicular ovaries, they were 63.95, 39.54 and 24.41. The results of this experiment demonstrate that no statistically significant difference (P<0.05) was verified in the frequency of cleaved embryos and morulae and blastocyst formation when comparing the three ovarian conditions in the same season. However the breeding season presented better results considering cleavage and morulae and blastocyst formation.

Silloitushitsauksen robotisointi

Tämän diplomityön tavoitteena oli tutkia ja selvittää kuormakoneen takarunkorakenteen silloitushitsauksen robotisointia. Työ päätettiin rajata koskemaan vain tiettyä moduulia takarungosta. Työssä kartoitettiin tarvittava laitteisto, selvitettiin runkomoduulin silloitusajat sekä arvioitiin investoinnin kannattavuutta. Silloituksen suorittavan järjestelmän vaatimuksena oli, että sen tulee asettaa osat paikoilleen hitsauskiinnittimeen ja tehdä tarvittavat silloitushitsaukset automaattisesti. Sopivaksi laitteistoksi osoittautui taloudellisuuden ja toiminnallisuuden näkökulmasta yhdestä kappaleenkäsittely- sekä hitsausrobotista muodostuva järjestelmä. Kappaleenkäsittelijän ohjauksessa käytetään konenäköä sekä osien paikannuksessa että laadunvarmistuksessa. Robotit liikkuvat yhteisellä lineaariradalla, jonka rinnalla on kappaleenkäsittelylaitteistoja hitsauskiinnittimineen. Robotisoinnin käyttöönotolla yhden takarungon moduulien kokoonpanoon ja silloitukseen käytettävä aika pienenee alle puoleen manuaaliseen työhön verrattuna. Näin saavutetaan merkittäviä kustannussäästöjä. Lisäksi hitsauskiinnittimet voivat olla verrattain yksinkertaisia manuaalityöhön verrattuna, jolloin myös säästetään työkaluinvestoinneissa. Robotisointiprojektin jatkotoimenpiteitä ovat laajamittaiset tuotantosimulaatiot layoutin, laitteiston sekä työkiertojen tarkaksi määrittämiseksi. Lisäksi itse tuotetta on muokattava paremmin robottisilloitukseen sopivaksi.

Fast pyrolysis in circulating fluidized bed: feasibility study

Today the limitedness of fossil fuel resources is clearly realized. For this reason there is a strong focus throughout the world on shifting from fossil fuel based energy system to biofuel based energy system. In this respect Finland with its proven excellent forestry capabilities has a great potential to accomplish this goal. It is regarded that one of the most efficient ways of wood biomass utilization is to use it as a feedstock for fast pyrolysis process. By means of this process solid biomass is converted into liquid fuel called bio-oil which can be burnt at power plants, used for hydrogen generation through a catalytic steam reforming process and as a source of valuable chemical compounds. Nowadays different configurations of this process have found their applications in several pilot plants worldwide. However the circulating fluidized bed configuration is regarded as the one with the highest potential to be commercialized. In the current Master’s Thesis a feasibility study of circulating fluidized bed fast pyrolysis process utilizing Scots pine logs as a raw material was conducted. The production capacity of the process is 100 000 tonne/year of bio-oil. The feasibility study is divided into two phases: a process design phase and economic feasibility analysis phase. The process design phase consists of mass and heat balance calculations, equipment sizing, estimation of pressure drops in the pipelines and development of plant layout. This phase resulted in creation of process flow diagrams, equipment list and Microsoft Excel spreadsheet that calculates the process mass and heat balances depending on the bio-oil production capacity which can be set by a user. These documents are presented in the current report as appendices. In the economic feasibility analysis phase there were at first calculated investment and operating costs of the process. Then using these costs there was calculated the price of bio-oil which is required to reach the values of internal rate of return of 5%, 10%, 20%, 30%, 40%, and 50%.

Biovoimalaitoksen energiatehokkuuden parantaminen ja osakuorma-ajon optimointi

Energiatehokkuus on nykyaikana yksi tärkeimmistä energiataloudellisista tekijöistä voimalaitosten sähköntuotannossa. Varsinkin yhteistuotantolaitoksissa joissa sähkö on lämpöenergian lisänä saatava sivutuote, sähkön tuotannon optimointi voi merkitä laitostalouden ja yrityksen kannalta huomattavia lisätuloja tai -säästöjä. Kaukaan Voima Oy:n biovoimalaitos on vuonna 2009 kaupalliseen käyttöön valmistunut moderni yhteistuotantolaitos, joka sijaitsee Lappeenrannassa UPM Kaukas sellutehtaan tehdasalueella. Voimalaitos tuottaa kaukolämpöä ja sähköä Lappeenrannan kaupungille sekä prosessihöyryä ja sähköä UPM Kaukaan tehtaille. Tämän työn tavoitteena on tarkastella biovoimalaitoksen omakäyttösähkön kulutusta kuukausitasolla verrattuna laitoksella tuotettavan höyryn määrään sekä etsiä voimalaitokselta kohteita, joiden omakäyttösähkön kulutusta voidaan vähentää vaikuttamatta höyryntuotantoon ja näin parantaa laitoksen energiatehokkuutta ja hyötysuhdetta. Työ rajataan käsittelemään voimalaitoksen apulaitteiden ja -järjestelmien omakäyttösähkön kulutusta. Työssä tarkastellaan vuodenaikojen vaihtelun ja kaukolämmön sekä prosessihöyryn tarpeen muutoksen vaikutusta voimalaitoksen ajomalliin sekä höyryntuotannon ja omakäyttösähkön kulutuksen suhteisiin. Työssä esiin nousseiden kohteiden potentiaaliset sähköenergian säästöt ovat noin 2500 MWh vuodessa joka tarkoittaa keskimäärin 3,7 % vähennystä voimalaitoksen kuukausittaiseen omakäyttösähkön kulutukseen. Kohteet eivät käytännössä vaadi minkaanlaista investointirahaa, vaan uusia ajojärjestelyitä. Keskeisimmiksi säästökohteiksi valikoitui laitoksen pumppausjärjestelmien paineenalennukset.

Validation and Selection of Transportation Cost Drivers with Advanced Methods

In today's logistics environment, there is a tremendous need for accurate cost information and cost allocation. Companies searching for the proper solution often come across with activity-based costing (ABC) or one of its variations which utilizes cost drivers to allocate the costs of activities to cost objects. In order to allocate the costs accurately and reliably, the selection of appropriate cost drivers is essential in order to get the benefits of the costing system. The purpose of this study is to validate the transportation cost drivers of a Finnish wholesaler company and ultimately select the best possible driver alternatives for the company. The use of cost driver combinations as an alternative is also studied. The study is conducted as a part of case company's applied ABC-project using the statistical research as the main research method supported by a theoretical, literature based method. The main research tools featured in the study include simple and multiple regression analyses, which together with the literature and observations based practicality analysis forms the basis for the advanced methods. The results suggest that the most appropriate cost driver alternatives are the delivery drops and internal delivery weight. The possibility of using cost driver combinations is not suggested as their use doesn't provide substantially better results while increasing the measurement costs, complexity and load of use at the same time. The use of internal freight cost drivers is also questionable as the results indicate weakening trend in the cost allocation capabilities towards the end of the period. Therefore more research towards internal freight cost drivers should be conducted before taking them in use.

Introduction of the T-10 static line parachuting capability to the NH90 helicopter

The purpose of this study was to investigate the suitability of the Finnish Defence Forces’ NH90 helicopter for parachuting operations with the T-10 static line parachute system. The work was based on the Army Command’s need to compensate for the reduction in the outsourced flight hours for the military static line parachuting training. The aim of the research was to find out the procedures and limitations with which the NH90 IOC+ or FOC version helicopter could be used for static line parachutist training with the T- 10B/MC1-1C parachutes. The research area was highly complicated and non-linear. Thus analytical methods could not be applied with sufficient confidence, even with present-day computing power. Therefore an empirical research method was selected, concentrating on flight testing supported with literature study and some calculated estimations. During three flights and 4.5 flight hours in Utti, Finland on 17−20 September 2012, a total of 44 parachute drops were made. These consisted of 16 dummy drops and 28 paratrooper jumps. The test results showed that when equipped with the floor mounted PASI-1 anchor line, the deflector bar of the NHIndustries’ Parachuting Kit and Patria’s floor protection panels the Finnish NH90 variant could be safely used for T-10B/MC1-1C static line parachuting operations from the right cabin door at airspeed range of 50−80 KIAS (∼90–150 km/h). The ceiling mounted anchor lines of the NHI’s Parachuting Kit were not usable with the T-10 system. This was due to the static lines’ unsafe behaviour in slipstream when connected to the cabin ceiling level. In conclusion, the NH90 helicopter can be used to meet the Army Command’s requirement for an additional platform for T-10 static line parachutist training. Material dropping, the effect of additional equipment and jumping from the rear ramp should be further studied.

Irtoamispäivän kurssilaskusuhteet, epänormaalit tuotot sekä epänormaalit kaupankäyntivolyymit vuosina 2005-2013

Tutkielman tavoitteena on tutkia osingon irtoamispäivän tapahtumia OMX Helsinki 25:n yrityksillä vuosina 2005–2013. Vallitsevan käsityksen mukaan osakkeen hinta laskee irtoamispäivänä osingon verran +/- markkinoiden yleisestä hintamuutoksesta johtuva nousu/lasku. Käsitystä on pyritty murtamaan vuosien saatossa neljän eri teorian avulla, jotka ovat veroasiakaskuntateoria, lyhytaikaisen vaihdon hypoteesi, dynaaminen malli sekä mikrorakenneteoria. Osingon irtoamispäivää tarkastellaan kolmen eri tutkimuksen avulla ja saatuja tuloksia verrataan teoriaan sekä aikaisempiin löydöksiin. Tutkimusosuudet ovat kurssilaskusuhteet, epänormaalit tuotot sekä epänormaalit kaupankäyntivolyymit. Kurssilaskusuhdetta tarkastellaan vertaamalla cum-päivän ja irtoamispäivän osakkeiden hintojen erotusta maksetun osingon määrään. Epänormaaleja tuottoja ja epänormaaleja kaupankäyntivolyymejä tarkastellaan tapahtumatutkimus-menetelmällä viisi päivää ennen ja viisi päivää jälkeen osingon irtoamisen. Kurssilaskusuhteet olivat eri tavoilla laskettuina 77 – 94 %. Irtoamispäivän ympärillä oli havaittavissa 1,5 %:n negatiivisia epänormaaleja tuottoja. Epänormaalit kaupankäyntivolyymit kasvoivat tasaisesti lähestyttäessä irtoamispäivää ja olivat voimakkaimmillaan irtoamispäivänä. Irtoamispäivän jälkeen kaupankäyntivolyymit palautuivat hiljalleen normaalille tasolle. Tulokset vastaavat aikaisempia löydöksiä kurssilaskusuhteita ja epänormaaleja volyymejä tarkasteltaessa, mutta eroavat epänormaaleissa tuotoissa.