Development of a spectrophotometric Sequential Injection Analysis (SIA) procedure for determination of ammonium: A Response Surface Methodology (RSM) approach

This paper describes the optimization and use of a Sequential Injection Analysis (SIA) procedure for ammonium determination in waters. Response Surface Methodology (RSM) was used as a tool for optimization of a procedure based on the modified Berthelot reaction. The SIA system was designed to (i) prepare the reaction media by injecting an air-segmented zone containing the reagents in a mixing chamber, (ii) to aspirate the mixture back to the holding coil after homogenization, (iii) drive it to a thermostated reaction coil, where the flow is stopped for a previously established time, and (iv) to pump the mixture toward the detector flow cell for the spectrophotometric measurements. Using a 100 mu mol L(-1) ammonium solution, the following factors were considered for optimization: reaction temperature (25 - 45 degrees C), reaction time (30 - 90 s), hypochlorite concentration (20 - 40 mmol L(-1)) nitroprusside concentration (10 - 40 mmol L(-1)) and salicylate concentration (0.1 - 0.3 mol L(-1)). The proposed system fed the statistical program with absorbance data for fast construction of response surface plots. After optimization of the method, figures of merit were evaluated, as well as the ammonium concentration in some water samples. No evidence of statistical difference was observed in the results obtained by the proposed method in comparison to those obtained by a reference method based on the phenol reaction. (C) 2010 Elsevier B.V. All rights reserved.

The electrochemical effect of acid functionalisation of carbon nanotubes to be used in sensors development

The electrochemical behaviour of multi-walled carbon nanotubes was compared with that of glassy carbon, and the differences were investigated by cyclic voltammetry and electrochemical impedance spectroscopy before and after acid pre-treatment. The electrochemical techniques showed that acid functionalisation significantly improves the electrocatalytic properties of carbon nanotubes. These electrocatalytic properties enhance the analytical signal, shift the oxidation peak potential to a less positive value, and the charge-transfers rate increase of both dopamine and K(4)[Fe(CN)(6)]. The functionalisation step and the resulting appearance of edge planes covered with different chemical groups were confirmed by FTIR measurements. Carbon nanotubes after acid pre-treatment are a potentially powerful analytical tool for sensor development. (C) 2010 Elsevier B.V. All rights reserved.

Är organisationen mogen för evidensbaserad vård? : översättning och validering av Alberta Context Tool och beskrivning av sjuksköterskors skattning av kontextuella faktorer inom ortopedisk vård

Syftet med denna studie var att reliabilitetstesta Alberta Context Tool (ACT) i svensk hälso- och sjukvård och beskriva ortopedsjuksköterskors skattning av kontextuella faktorer såsom ledarskap, arbetskultur, återkoppling, utvecklingsmöjligheter och forskningsanvändning, som kan påverka möjligheten att omsätta forskningsresultat i vårdarbetet. Urvalet bestod av 119 sjuksköterskor som arbetade på ortopediska vårdavdelningar på sex olika sjukhus i mellersta Sverige. ACT är ett frågeformulär framtaget utifrån de senaste årens forskning om vilka faktorer i kontexten som har betydelse för sjuksköterskors forskningsanvändning. Reliabilitetstest gjordes enligt analys med Chronbach`s Alpa och innehållsvaliditet. Resultatet visade att ACT var relevant att användas för sjuksköterskor som arbetar på ortopedisk vårdavdelning i Sverige. Reliabilitetstesten med Chronbach´s Alpa gav värden nära 0,7 för de åtta frågeområden som behandlar kontexten.Sjuksköterskorna rapporterade att det fanns brister i många av de delar av kontexten som enligt forskning visat sig ha betydelse för möjligheten att implementera evidensbaserad vård. Sjuksköterskorna trivdes med sitt arbete och kände att deras kunskaper värderades högt i vårdteamet. Resultatet visade dock att det inte fanns tillräckligt stöd från ledningen för att utveckla vården. De rapporterade att de nästan inte alls fick återkoppling i vårdarbetet. Det saknades stödfunktioner och strategier för att implementering av forskningsresultat skulle vara möjligt att implementera i vårdarbetet. Majoriteten av sjuksköterskorna såg positivt på forskningsanvändning.

Conceptual Product Development in Small Corporations

The main objective of the thesis “Conceptual Product Development in Small Corporations” is by the use of a case study test the MFD™-method (Erixon G. , 1998) combined with PMM in a product development project. (Henceforth called MFD™/PMM-method). The MFD™/PMM-method used for documenting and controlling a product development project has since it was introduced been used in several industries and projects. The method has been proved to be a good way of working with the early stages of product development, however, there are almost only projects carried out on large industries which means that there are very few references to how the MFD™/PMM-method works in a small corporation. Therefore, was the case study in the thesis “Conceptual Product Development in Small Corporations” carried out in a small corporation to find out whether the MFD™/PMM-method also can be applied and used in such a corporation.The PMM was proposed in a paper presented at Delft University of Technology in Holland 1998 by the author and Gunnar Erixon. (See appended paper C: The chart of modular function deployment.) The title “The chart of modular function deployment” was later renamed as PMM, Product Management Map. (Sweden PreCAD AB, 2000). The PMM consists of a QFD-matrix linked to MIM (Module Indication Matrix) via a coupling matrix which makes it possible to make an unbroken chain from the customer domain to the designed product/modules. The PMM makes it easy to correct omissions made in creating new products and modules.In the thesis “Conceptual Product Development in Small Corporations” the universal MFD™/PMM-method has been adapted by the author to three models of product development; original-, evolutionary- and incremental development.The evolutionary adapted MFD™/PMM-method was tested as a case study at Atlings AB in the community Ockelbo. Atlings AB is a small corporation with a total number of 50 employees and an annual turnover of 9 million €. The product studied at the corporation was a steady rest for supporting long shafts in turning. The project team consisted of management director, a sales promoter, a production engineer, a design engineer and a workshop technician, the author as team leader and a colleague from Dalarna University as discussion partner. The project team has had six meetings.The project team managed to use MFD™ and to make a complete PMM of the studied product. There were no real problems occurring in the project work, on the contrary the team members worked very well in the group, having ideas how to improve the product. Instead, the challenge for a small company is how to work with the MFD™/PMM-method in the long run! If the MFD™/PMM-method is to be a useful tool for the company it needs to be used continuously and that requires financial and personnel resources. One way for the company to overcome the probable lack of recourses regarding capital and personnel is to establish a good cooperation with a regional university or a development centre.

Kraftutveckling för manuella trädfällningsredskap : Force development for manual tree felling tools

The objective with this study has been to build general models of the mechanics in tree felling with chain-saw and to compare felling torque for different tools. The theoretical models are completed and validated with a comparative study. The study includes a great number of felling tools of which some are used with different methods. Felling torque was measured using a naturally like measuring arrangement where a tree is cut at about 3.7 m height and then anchored with a dynamometer to a tree opposite to the felling direction. Notch and felling cut was made as ordinary with exception that the hinge was made extra thin to reduce bending resistance. The tree was consequently not felled during the trials and several combinations of felling tools and individuals could be used on the same tree.The results show big differences between tools, methods and persons. The differences were, however, not general, but could vary depending on conditions (first of all tree diameters). Tools and methods that push or pull on the stem are little affected by the size of the tree, while tools that press on the stump are very much dependent of a large stump-diameter. Hand force asserted on a simple pole is consequently a powerful tool on small trees. For trees of medium size there are several alternative methods with different sizes and brands of felling levers and wedges. Larger and more ungainly tools and methods like tree pusher, winch, etc. develop very high felling torque on all tree sizes. On large trees also the felling wedge and especially the use of several wedges together develop very high felling torque.

Extended local labor markets due to high speed trains : Visualization of estimations in the Swedish national travel demand forecasting tool, SAMPERS

Wider economic benefits resulting from extended geographical mobility is one argument for investments in high-speed rail. More specifically, the argument for high-speed trains in Sweden has been that they can help to further spatially extend labor market regions which in turn has a positive effect on growth and development. In this paper the aim is to cartographically visualize the potential size of the labor markets in areas that could be affected by possible future high-speed trains. The visualization is based on the forecasts of labor mobility with public transport made by the Swedish national mobility transport forecasting tool, SAMPERS, for two alternative high-speed rail scenarios. The analysis, not surprisingly, suggests that the largest impact of high-speed trains results in the area where the future high speed rail tracks are planned to be built. This expected effect on local labor market regions of high-speed trains could mean that possible regional economic development effects also are to be expected in this area. However, the results, in general, from the SAMPERS forecasts indicaterelatively small increases in local labor market potentials.

Modeling and illustrating requirement prioritization in public e-service development from a value-based perspective

A major problem in e-service development is the prioritization of the requirements of different stakeholders. The main stakeholders are governments and their citizens, all of whom have different and sometimes conflicting requirements. In this paper, the prioritization problem is addressed by combining a value-based approach with an illustration technique. This paper examines the following research question: How can multiple stakeholder requirements be illustrated from a value-based perspective in order to be prioritizable? We used an e-service development case taken from a Swedish municipality to elaborate on our approach. Our contributions are: 1) a model of the relevant domains for requirement prioritization for government, citizens, technology, finances and laws and regulations; and 2) a requirement fulfillment analysis tool (RFA) that consists of a requirement-goal-value matrix (RGV), and a calculation and illustration module (CIM). The model reduces cognitive load, helps developers to focus on value fulfillment in e-service development and supports them in the formulation of requirements. It also offers an input to public policy makers, should they aim to target values in the design of e-services.

Wear of coated and uncoated PCBN cutting tool used in turning and milling

This licentiate thesis has the main focus on evaluation of the wear of coated and uncoated polycrystalline cubic boron nitride cutting tool used in cutting operations against hardened steel. And to exam the surface finish and integrity of the work material used. Harder work material, higher cutting speed and cost reductions result in the development of harder and more wear resistance cutting tools. Although PCBN cutting tools have been used in over 30 years, little work have been done on PVD coated PCBN cutting tools. Therefore hard turning and hard milling experiments with PVD coated and uncoated cutting tools have been performed and evaluated. The coatings used in the present study are TiSiN and TiAlN. The wear scar and surface integrity have been examined with help of several different characterization techniques, for example scanning electron microscopy and Auger electron spectroscopy.   The results showed that the PCBN cutting tools used displayed crater wear, flank wear and edge micro chipping. While the influence of the coating on the crater and flank wear was very small and the coating showed a high tendency to spalling. Scratch testing of coated PCBN showed that, the TiAlN coating resulted in major adhesive fractures. This displays the importance of understanding the effect of different types of lapping/grinding processes in the pre-treatment of hard and super hard substrate materials and the amount and type of damage that they can create. For the cutting tools used in turning, patches of a adhered layer, mainly consisting of FexOy were shown at both the crater and flank. And for the cutting tools used in milling a tribofilm consisting of SixOy covered the crater. A combination of tribochemical reactions, adhesive wear and mild abrasive wear is believed to control the flank and crater wear of the PCBN cutting tools. On a microscopic scale the difference phases of the PCBN cutting tool used in turning showed different wear characteristics. The machined surface of the work material showed a smooth surface with a Ra-value in the range of 100-200 nm for the turned surface and 100-150 nm for the milled surface. With increasing crater and flank wear in combination with edge chipping the machined surface becomes rougher and showed a higher Ra-value. For the cutting tools used in milling the tendency to micro edge chipping was significant higher when milling the tools steels showing a higher hard phase content and a lower heat conductivity resulting in higher mechanical and thermal stresses at the cutting edge.

Teachers’ Views on ICT as a Tool in English Teaching for Students with Dyslexia : An interview study with English teachers in grades 7-9

Information and communications technology (ICT) is a broad concept, which is often discussed in relation to the development of education. More specially, ICT can be seen as a tool to help teachers individualize students’ education. Students who have literacy difficulties, such as dyslexia, are in constant need of new techniques to help them learn and new tools to make their educational development easier. The aim of this thesis is to show what views teachers have regarding using ICT in English teaching at a sample of schools in the south of Sweden. A secondary part of the aim is to see what ICT tools, or other non ICT related methods, these teachers use to improve literacy skills for students with dyslexia.This empirical study is based on interviews with six participants. Previous research within the area is presented and different aspects of ICT within the National Agency for Education in Sweden, and the English syllabus, are also discussed. The results of this thesis show that ICT is seen as a helpful tool to make education easier for both students and teachers. Tools such as ViTal, Spell Right and Legimus are being used and the participants of the study also use iPads and Chromebooks in their teaching. According to the interviews, ICT can tribute to a fun way of learning and a more individualized education. Other non ICT related methods are also used to help students with dyslexia and these are often in terms of pictures in connection to words. These findings are based on a limited number of participants in a small area of south of Sweden. Therefore, further research is needed to see if the findings can be verified with more participants, in different parts of the country.

Using Interlibrary Loan Data as a Section Tool: ILL Trails Provide Collection Clues

This article describes analyzing Interlibrary Loan data to help inform collection management decision and offers guidance for formulating policies for discerning borrowed titles indicative of gaps in the library from special-interest pursuits beyond the scope of the university curriculum.

Property rights as a public policy tool: an empirical analysis of the social and economic effects

Secure property rights are considered a key determinant of economic development. However, the evaluation of the causal effects of land titling is a difficult task. The Brazilian government through a program called "Papel Passado" has issued titles, since 2004, to over 85,000 families and has the goal to reach 750,000. Furthermore, another topic in Public Policy that is crucial to developing economies is income generation and child labor force participation. Particularly, in Brazil, about 5.4 million children and teenagers between 5 and 17 years old are still working. This thesis examines the direct impact of securing a property title on income and child labor force participation. In order to isolate the causal role of ownership security, this study uses a comparison between two close and very similar communities in the City of Osasco case (a town with 650,000 people in the São Paulo metropolitan area). One of them, Jardim Canaã, was fortunated to receive the titles in 2007, the other, Jardim DR, given fiscal constraints, only will be part of the program schedule in 2012, and for that reason became the control group. Also, this thesis also aims to test if there is any relationship between land title and happiness. The estimates suggest that titling results in a substantial decrease of child labor force participation, increase of income and happiness for the families that received the title compared to the others.

An evaluation of the Business Model Canvas by technology-oriented startups in Brazil : a qualitative study about the usage of the tool by Brazilian entrepreneurs

The following paper was conducted with the support of several entrepreneurs and startups from Brazil. The aim of the research was to find out which impact the Business Model Canvas, further abbreviated as BMC, has on technology-oriented startups in Brazil. The first step of the study was identify some general concepts of entrepreneurship, as well as the conditions and environment of the country. Afterwards, it was focused on defining and comparing different business model tools and concepts to the BMC. After the literature review and meeting with several professionals in the area of entrepreneurship and startups, a questionnaire was formulated in order to conduct the qualitative study and identify the main impact of the tool. The questionnaire was answered by ten startups. In order to check the validity and credibility of the research outcomes, theory and investigator triangulation was used. As a result, the usage of the BMC could be evaluated by obtaining the outcomes and the theory, which showed that Brazilian tech startups are using Osterwalder’s model for the reason of idea creation and testing, validating and pivoting their business model. Interestingly, the research revealed that the entrepreneurs are using the tool often not in the traditional way of printing it, but rather applying it as a thinking approach. Besides, the entrepreneurs are focusing mostly on developing a strong Value Proposition, Customer Segment and sustainable Revenue Streams, while afterwards the remaining building blocks are built. Moreover, the research showed that the startups are using also other concepts, such as the Customer Development Process or Build-Measure-Learn Feedback Loop. These methodologies are often applied together with the BMC and helps to identify the most sustainable components of the business idea. Keywords: Business

Social entrepreneurship, microcredit and development challenges: a case study analysis of Banco Pérola

The term “social entrepreneurship” has been attracting growing interest from different sectors in the past years, driven by the possibility of employing business techniques to tackle recurrent social and environmental issues. At the forefront of this global phenomenon is microcredit, seen by many as an effective anti-poverty tool and having the Grameen Bank as its flagship program. While the prospects of social entrepreneurship seem promising, the newness of the concept and its somewhat confusing definition make conditions difficult to analyze this contemporary phenomenon. Therefore, the objective of this study was to discuss the challenges faced by social entrepreneurs and alternatives of development for social businesses through a case study on a Brazilian microcredit institution and inclusive business, Banco Pérola. The case addresses a growing need for case studies designed for teaching in the field of social entrepreneurship. It was focused mainly on understanding the development challenges within Banco Pérola, and built based on interviews carried out with top management, credit officer and clients of the institution, as well as on secondary data collected. An analysis of the case study was performed under a Teaching Notes. As illustrated by the Banco Pérola case, the main difficulties encountered by social entrepreneurs relate to the systematization of processes and creation of operational routines, including for performance evaluation (impact assessment tools); to the capture and management of both financial and human capital; to scaling up the business model and to the need of forging closer and more personal relationships with customers as against in traditional banking practices. In spite of certain limitations, such as the fact that the case might soon become outdated due to the fast-changing environment surrounding Banco Pérola, or the fact that not all relevant stakeholders (e.g. partners) were selected for interviews, the research objective has been achieved and the study can be seen as a contribution to spreading the concept of social entrepreneurship.