Cr4+在Al2O3多晶体中的光谱性能研究

Transparent polycrystalline Cr:Al2O3 ceramics were synthesized by conventional pressureless synthesis processing. The absorption and emission spectra of Cr:Al2O3 ceramics specimens before and after annealing were measured at room temperature. It was discovered that the emission spectra of Cr4+ in Al2O3 octahedral coordination site is in infrared wavelength range of 1100-1600 nm. The emission peak of Cr4+ is centered at 1223 nm, which is similar to that of Cr4+ in tetrahedral site. Al2O3 has smaller lattice constant, resulting in the larger crystal field strength, so there is a blue shift in the peak of Cr4+:Al2O3 ceramics compared to those of other Cr4+-doped crystals. And the emission band is much narrower with full width at half maximum Delta lambda 37 nm.

VTE法制备γ-LiAlO2／α-Al2O3复合衬底以及腐蚀和退火对其影响

通过气相传输平衡法(VTE)制备了γ-LiAlO2／α-Al2O3复合衬底，使用5％的稀盐酸对其进行腐蚀并在900℃退火72h。利用X射线衍射、偏光显微镜及扫描电镜对复合衬底进行了分析，发现在白宝石α面(11-20)和γ面(1—102)均获得单相多晶的γ-LiAlO2，且后者的择优取向好于前者。腐蚀可以提高样品的择优取向，在5％的稀盐酸中，时间控制在2min左右可获得较好的结果。退火后γ-LiAlO2颗粒质量得到改善，白宝石α面上γ-LiAlO2的质量优于r面上的γ-LiAlO2，两者都出现颗粒长大现象。

温梯法生长的Ti：Al2O3晶体的光谱分析

本文研究了不同掺Ti^3＋浓度对温梯法生长的Ti：Al2O3晶体吸收光谱、荧光光谱和X射线衍射光谱的影响。根据吸收光谱提出了一个色心模型。对比了样品各处420nm荧光谱，发现掺Ti^3＋浓度越大，该处荧光强度越弱，同时解释了420肿处荧光峰的起源。对比了样品各处720nm处的荧光谱，发现掺Ti^3＋浓度越大，该处荧光强度越强。X射线衍射谱（XRD）表明，衍射峰强度随掺Ti^3＋浓度的增大而逐渐增强。

Ti：Al2O3透明多晶陶瓷光谱特性分析

采用传统无压烧结工艺制备出透明性良好的掺Ti氧化铝陶瓷；测定了该陶瓷的吸收光谱、荧光光谱和激发光谱。结果表明，掺Ti氧化铝透明陶瓷样品在Mg与Ti掺入离子的摩尔比（NMg／NTi）较小时，表现出Ti^3＋离子的490nm特征吸收峰，即^2T2→^2E跃迁产生的宽带吸收；NMg／NTi较大时，陶瓷样品吸收光谱中不存在Ti^3＋离子吸收，其250nm处吸收为O^2-→Ti^4＋的转移吸收。掺Ti氧化铝透明陶瓷样品Ti^3＋离子的发射谱线与单晶的相吻合，同时Ti^3＋在氧化铝陶瓷中分布很均匀，且Ti^3＋浓度较

Al2O3衬底上生长ZnO薄膜的结构和光学特性

用脉冲激光沉积法在Al2O3（0001）衬底上沉积了ZnO薄膜。衬底温度分别为300℃、400℃、500℃、600℃和700℃。利用X射线衍射（XRD）和光致发光谱（PL）对薄膜的结构和光学性能进行研究。X射线衍射的结果表明在不同温度下生长的ZnO薄膜均具有高度c轴择优取向，衬底温度400℃时，膜的应力较小质量较高。ZnO薄膜有很强的紫外发光峰，紫外发光峰的强度与衬底温度密切相关，并发现当衬底温度从300℃增到400℃时，紫外发射峰出现6nm的蓝移。

Cr^4＋在Al2O3透明陶瓷中的发光行为

采用传统无压烧结工艺制备出透明性良好的掺Cr的Al2O3透明陶瓷；测定了其吸收光谱和荧光光谱，发现在Al2O3六配位的八面体结构中，除了有Cr^3＋离子的特征吸收峰外，由于有Mg^2＋的电荷补偿作用，也有Cr^4＋离子，Cr^4＋的荧光发射峰位于1223nm附近，与Cr^4＋在四面体中的发光行为一致。但其荧光发射峰较窄，半高宽△λ仅为37nm。

温梯法蓝宝石（Al2O3）晶体的脱碳去色退火研究

温度梯度法（TGT）生长的Al2O3晶体因石墨发热体在高温时的挥发和原料中过渡性金属离子的存在，晶体在不同部位呈现不同颜色，一般上部为浅红色，尾部为浅黄绿色，将TGT法生长的Al2O3晶体（Ф110×80mm^3）依次经过高温氧化气氛、高温还原气氛脱碳、去色退火实验，即“两步法”退火实验，晶体变成无色、透明，经测试，Al2O3晶体的完整性、光学透过率和光学均匀性均有显著提高。

Edge-defined, film-fed growth (EFG) technique for the preparation of alpha-Al2O3 : C crystal with highly sensitive thermoluminescence response

In this work, alpha-Al2O3:C, a highly sensitive thermoluminescence dosimetry crystal, was grown by the EFG method in which a graphite heating unit and shield acted as the carbon source during the growth process. The optical, luminescent properties and dosimetric characteristics of the crystal were investigated. The as-grown crystal shows a single glow peak at 536 K, which is associated with Cr3+ ions. After annealing in H-2 at 1673 K for 80 h, the crystal shows a single glow peak at 460 K and a blue emission band at 415 nm. The thermoluminescent response of the annealed crystal shows linear-sublinear-saturation characteristics in the dose range from 5 x 10(-6) to 100 Gy.

Growth of highly sensitive thermoluminescent crystal alpha-Al2O3 : C by the temperature gradient technique

In this work, an alpha-Al2O3:C crystal with highly sensitive thermoluminescence was directly grown by the temperature gradient technique (TGT) using Al2O3 and graphite powders as raw materials. The optical and luminescent properties and the dosimetric characteristics of the crystal were investigated. An as-grown alpha-Al2O3:C crystal shows a single glow peak at 462 K and a blue emission peak at 415 nm. The thermoluminescence (TL) response of the crystal shows a linear-sublinear-saturation characteristic. In the dose range from 5 x 10(-6) to 10Gy, the alpha-Al2O3:C crystal shows excellent linearity, and saturation was observed at about 30Gy. The sensitivity of the crystal decreases as the heating rate increases. (c) 2008 Elsevier B.V. All rights reserved.

Growth of alpha-Al2O3:C crystal with highly sensitive optically stimulated luminescence

In this work. an alpha-Al2O3:C crystal was directly grown by the temperature gradient technique (TGT) using Al2O3 and graphite powders as the raw materials. The optical, optically stimulated luminescence (OSL) properties and dosimetric characteristics of as-grown crystal were investigated. As-grown alpha-Al2O3:C crystal shows strong absorption band at 205, 230 and 256 nm. Three-dimensional thermoluminescence (TL) emission spectrum of the crystal shows a single emission peak at similar to 415 nm. The OSL decay curve can be fitted to two exponentials, the faster component and the slower component. The OSL response of the crystal shows a linear-sublinear-saturation characteristic. As-grown alpha-Al2O3:C crystal shows excellent linearity in the dose range from 5 x 10(-6) to 50 Gy. For doses higher than the saturation dose (100 Gy). the OSL sensitivity decreases as the dose increases. Crown Copyright (C) 2008 Published by Elsevier B.V. All rights reserved.

The study on the interface adhesion comparison of the MgF2, Al2O3, SiO2 and Ag thin films

Adhesion between the interface of pure silver thin film and three kinds of low refractive index coatings MgF2, Al2O3, SiO2 were compared in this article. The results indicated that the adhesion of Al2O3 and Ag was evidently superior to that of MgF2 and Ag, and the adhesion of MgF2 and Ag was evidently superior to that Of SiO2 and Ag. Reasons were analyzed accordingly. On the other hand, we compared the effect on the optical characteristic of Ag film when these three kinds of films were used as protective coatings and enhanced coatings. Considering the difference of the adhesion between Ag and MgF2, Al2O3, SiO2, suited uses are given for each other. © 2004 Elsevier B.V. All rights reserved.

Study of Al2O3/MgF2 HR coatings at 355 nm

With the present work we tried to study the effective methods to improve the laser-induced damage threshold (LIDT) and reflectance of HR coatings at 355 nm. The work presented in this paper wits part of an ongoing study about vacuum annealing. It was dedicated to study the effects Of Vacuum annealing with different temperature gradients on the structure, optical properties and laser-induced damage threshold (LIDT) of 355nm Al2O3/MgF2HR coatings. A number of samples were prepared by electron beam evaporation using the same deposition process with an optimal deposition temperature of 280 degrees C. After deposition, samples were annealed in the coating chamber for 3 h with different temperature gradients. Morphologies of the samples were observed by Leica-DMRXE. Microscope, Structure of the samples had been characterized by X-ray diffraction (XRD). Transmittance and reflectance of the samples were measured by Lambda 900 Spectrometer, The LIDT of the samples was measured by a 355 nm Nd:YAG laser with a pulse width of 8 ns. It was found that the temperature gradient of vacuum annealing had significant effects on the morphology, structure, absorption, and LIDT of the samples, (c) 2005 Elsevier Ltd. All rights reserved.

退火对电子束热蒸发193nm Al2O3/MgF2反射膜性能的影响

设计并镀制了193nm Al2O3/MgF2反射膜,对它们在空气中分别进行了250-400℃的高温退火,测量了样品的透射率光谱曲线和绝对反射率光谱曲线.发现样品在高反射区的总的光学损耗随退火温度的升高而下降,而后趋于饱和.采用总积分散射的方法对样品在不同退火温度下的散射损耗进行了分析,发现随着退火温度的升高散射损耗有所增加.因此,总的光学损耗的下降是由于吸收损耗而不是散射损耗起主导作用.对Al2O3材料的单层膜进行了同等条件的退火处理,由它们光学性能的变化推导出它们的折射率和消光系数的变化,从而解释了相应

High-reflectance 193 nm Al2O3/MgF2 mirrors

Thin-film single layers of Al2O3 and MgF2 were deposited upon super polished fused-silica by electron-beam evaporation. The subsequent optical constants n and k were reported for the spectral range of 180-230 nm. High-reflectance dense multilayer coatings for 193 nm were designed on the basis of the evaluated optical constants and produced. The spectra of the reflectance of HR coatings were compared to the theoretical calculations. HR mirrors of 27 layers with a reflectance of more than 98% were reported. (c) 2004 Elsevier B.V. All rights reserved.

Annealing effects on electron-beam evaporated Al2O3 films

The effects of post-deposited annealing on structure and optical properties of electron-beam evaporated Al2O3 single layers were investigated. The films were annealed in air for 1.5 h at different temperatures from 250 to 400 degrees C. The optical constants and cut-off wavelength were deduced. Microstructure of the samples was characterized by X-ray diffraction (XRD). Profile and surface roughness measurement instrument was used to determine the rms surface roughness. It was found that the cut-off wavelength shifted to short wavelength as the annealing temperature increased and the total optical loss decreased. The film structure remained amorphous even after annealing at 400 degrees C temperature and the samples annealed at higher temperature had the higher rms surface roughness. The decreasing total optical loss with annealing temperature was attributed to the reduction of absorption owing to oxidation of the film by annealing. Guidance to reduce the optical loss of excimer laser mirrors was given. (c) 2004 Elsevier B.V. All rights reserved.