Determinação de eletrólitos, gases sanguíneos, osmolalidade, hematócrito, hemoglobina, base titulável e anion gap no sangue venoso de equinos destreinados submetidos a exercício máximo e submáximo em esteira rolante

Estudaram-se as alterações nos eletrólitos, nos gases sanguíneos, na osmolalidade, no hematócrito, na hemoglobina, nas bases tituláveis e no anion gap no sangue venoso de 11 equinos da raça Puro Sangue Árabe, destreinados, submetidos a exercício máximo e submáximo em esteira rolante. Esses animais passaram por período de três dias de adaptação à esteira rolante e posteriormente realizaram dois exercícios testes, um de curta e outro de longa duração. Foram coletadas amostras de sangue venoso antes, imediatamente após e 30 minutos após o término dos exercícios. Após a realização do exercício máximo, observou-se diminuição significativa no pHv, na PvCO2, no HCO3, na cBase além de elevação no AG. Detectou-se também aumento do K+, do Ht e da Hb. Ao final do exercício submáximo, constatou-se somente aumento significativo no pHv, na cBase, na SatvO2 e na PvO2. Conclui-se que os equinos submetidos a exercício máximo desenvolveram acidose metabólica e alcalose respiratória compensatória, hipercalemia e aumento nos valores de hematócrito e hemoglobina. No exercício submáximo, os animais apresentaram alcalose metabólica hipoclorêmica e não ocorreram alterações no equilíbrio hidroeletrolítico.

Enterorrafias em plano aposicional convencionale com adesivo à base de cianoacrilato no cólon descendente de eqüinos

Em eqüinos, as enterotomias no cólon descendente são necessárias para remover enterólitos, corpos estranhos e material alimentar compactado que não podem ser removidos por técnicas conservativas. Este segmento intestinal possui um suprimento sangüíneo pobre, além de predisposição a complicações pós-operatórias relacionadas à contaminação bacteriana. Assim, este estudo foi conduzido com o objetivo de efetuar avaliações clínicas e anatomopatológicas do emprego de adesivo tecidual à base de cianoacrilato no cólon descendente de eqüinos, comparando-o a uma técnica de sutura aposicional convencional. A intervenção cirúrgica foi realizada em 15 animais posicionados em decúbito lateral direito, através de laparotomia pelo flanco esquerdo, sob anestesia geral inalatória. Após a exteriorização do cólon descendente, foram realizadas duas enterotomias de cinco centímetros de extensão cada, distanciadas 20cm uma da outra. Os animais foram aleatoriamente distribuídos em cinco tempos de observação de três animais cada e sacrificados aos três, sete, 14, 35 e 70 dias de pós-operatório. O adesivo butil-2-cianoacrilato e o fio de poliglactina 910 mostraram-se igualmente apropriados para uso em enterorrafias desse órgão, sendo que o fio de poliglactina 910 provocou inflamação inicial mais intensa que o cianoacrilato e, mais tardiamente, ambos causaram inflamação granulomatosa do tipo corpo estranho observada, primeiramente, junto ao fio de poliglactina 910 (7º dia) e, a partir do 35º dia, ao redor do cianoacrilato.

A função social do contrato como concretização de direitos fundamentais nas relações privadas

This dissertation deals with the social function of the contract, based on constitutional principles, especially those relating to fundamental rights. The social function of the contract (general clause) is described in the Civil Code so intentionally generic, no precise criteria to define it. Because of the fluidity of this principle, it is justified its closer study, seeking to assess its various meanings and looking away from the legal uncertainty that an unlimited conceptual vagueness can cause. The social function of the contract arises from a transformation experienced in private law from the inflows received from the Constitutional Law, the result of an evolutionary process by which it became the state structure, leaving the foundations of the classical liberal state and moving toward a vision guided by existential human values that give the keynote of the Welfare State. Arose, then the concern about the effectiveness of fundamental rights in relations between individuals, which is studied from the inapplicability of fundamental rights in private relations (U.S. doctrine of State action), passing to the analysis of the Theory of indirect horizontal effect of fundamental rights (of German creation and majority acceptance), reaching the right horizontal efficacy Theory of fundamental rights, prevailing Brazilian doctrine and jurisprudence. It has also been investigated the foundations of the social contract, pointing out that, apart from the provisions of the constitutional legislation, that base the principle on screen, there have also been noticed foundations in the Federal Constitution, in devices like the art. 1, III, the dignity of the human person is the north of the relationship between contractors. Also art. 3rd, I CF/88 bases the vision of social covenants, equipping it for the implementation of social solidarity, as one of the fundamental objectives of the Republic. Still on art. 170 of the Constitution it is seen as a locus of reasoning in the social function of the contract, the maintenance of the economic order. It is also studied the internal and external aspects of the social function of the contract, being the first part the one that considers the requirement of respect for contractual loyalty, through the objective good faith, as a result of the dignity of the hirer may not be offended by the other through the contract. On the other hand, the external facet of the social function of the contract, in line with the constitutional mandate of solidarity, indicates the need for contractors to respect the rights of society, namely the diffuse, collective and individual third party. In this external appearance, it is also pointed the notion of external credit protection, addressing the duty of society to respect the contract. There has been shown some notions of the social contract in comparative law. Then, there has been investigated the content of principle study, through their interrelationships with other provisions of private and constitutional law, namely equality, objective good faith, private autonomy and dignity of the human person. We study the application of the social contract in contractual networks as well as the guidance of conservation of contracts, especially those denominated long-term captive contracts, considering the theory of substantive due performance, concluding with an analysis of the social contract in code of Consumer Protection

Relationship of black layer and milk line development on maize seed maturity

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Uso de técnicas de otimização baseadas em derivadas como suporte do planejamento operacional de redes de distribuição de energia elétrica

The usual programs for load flow calculation were in general developped aiming the simulation of electric energy transmission, subtransmission and distribution systems. However, the mathematical methods and algorithms used by the formulations were based, in majority, just on the characteristics of the transmittion systems, which were the main concern focus of engineers and researchers. Though, the physical characteristics of these systems are quite different from the distribution ones. In the transmission systems, the voltage levels are high and the lines are generally very long. These aspects contribute the capacitive and inductive effects that appear in the system to have a considerable influence in the values of the interest quantities, reason why they should be taken into consideration. Still in the transmission systems, the loads have a macro nature, as for example, cities, neiborhoods, or big industries. These loads are, generally, practically balanced, what reduces the necessity of utilization of three-phase methodology for the load flow calculation. Distribution systems, on the other hand, present different characteristics: the voltage levels are small in comparison to the transmission ones. This almost annul the capacitive effects of the lines. The loads are, in this case, transformers, in whose secondaries are connected small consumers, in a sort of times, mono-phase ones, so that the probability of finding an unbalanced circuit is high. This way, the utilization of three-phase methodologies assumes an important dimension. Besides, equipments like voltage regulators, that use simultaneously the concepts of phase and line voltage in their functioning, need a three-phase methodology, in order to allow the simulation of their real behavior. For the exposed reasons, initially was developped, in the scope of this work, a method for three-phase load flow calculation in order to simulate the steady-state behaviour of distribution systems. Aiming to achieve this goal, the Power Summation Algorithm was used, as a base for developing the three phase method. This algorithm was already widely tested and approved by researchers and engineers in the simulation of radial electric energy distribution systems, mainly for single-phase representation. By our formulation, lines are modeled in three-phase circuits, considering the magnetic coupling between the phases; but the earth effect is considered through the Carson reduction. It s important to point out that, in spite of the loads being normally connected to the transformer s secondaries, was considered the hypothesis of existence of star or delta loads connected to the primary circuit. To perform the simulation of voltage regulators, a new model was utilized, allowing the simulation of various types of configurations, according to their real functioning. Finally, was considered the possibility of representation of switches with current measuring in various points of the feeder. The loads are adjusted during the iteractive process, in order to match the current in each switch, converging to the measured value specified by the input data. In a second stage of the work, sensibility parameters were derived taking as base the described load flow, with the objective of suporting further optimization processes. This parameters are found by calculating of the partial derivatives of a variable in respect to another, in general, voltages, losses and reactive powers. After describing the calculation of the sensibility parameters, the Gradient Method was presented, using these parameters to optimize an objective function, that will be defined for each type of study. The first one refers to the reduction of technical losses in a medium voltage feeder, through the installation of capacitor banks; the second one refers to the problem of correction of voltage profile, through the instalation of capacitor banks or voltage regulators. In case of the losses reduction will be considered, as objective function, the sum of the losses in all the parts of the system. To the correction of the voltage profile, the objective function will be the sum of the square voltage deviations in each node, in respect to the rated voltage. In the end of the work, results of application of the described methods in some feeders are presented, aiming to give insight about their performance and acuity

Fontes de metionina em rações formuladas com base em aminoácidos totais ou digestíveis para frangas de reposição leves e semipesadas

Foram conduzidos dois experimentos com o objetivo de avaliar a utilização de duas fontes de metionina (em pó ou líquida) em rações formuladas com base em aminoácidos digestíveis ou totais para frangas de reposição leves e semipesadas, nas fases inicial (de 1 a 6 semanas de idade) e de crescimento (de 11 a 16 semanas de idade). em cada experimento, foram utilizadas 384 aves distribuídas em delineamento inteiramente ao acaso, em esquema fatorial 2 × 2 × 2, composto de duas linhagens (Hy-Line W36 e Hy-Line Brown), duas fontes de metionina (HMTBA - 88% e DL-Metionina - 99%) e dois critérios de formulação da dieta (aminoácidos totais e digestíveis), totalizando oito tratamentos, cada um com seis repetições de oito aves. Foram avaliados os consumos de ração, proteína bruta e energia metabolizável, o peso e ganho de peso corporal e a conversão alimentar das aves. Não houve interação entre os fatores para nenhuma das variáveis estudadas. As aves da linhagem Brown apresentaram maior consumo de ração, peso corporal e ganho de peso. As fontes de metionina e os critérios de formulação de ração não influenciaram as características de desempenho. As aves das linhagens W36 e Brown da linhagem Hy-Line apresentam diferentes perfis de desenvolvimento corporal. A metionina em pó (DL-metionina - 99%) ou a líquida (HMTBA - 88%), assim como os critérios de formulação de ração (aminoácidos totais ou digestíveis) proporcionam desempenho semelhante em aves de reposição.

Um algoritmo para estimação de estado em alimentadores de distribuição de energia elétrica com base no método da soma de potências

Most algorithms for state estimation based on the classical model are just adequate for use in transmission networks. Few algorithms were developed specifically for distribution systems, probably because of the little amount of data available in real time. Most overhead feeders possess just current and voltage measurements at the middle voltage bus-bar at the substation. In this way, classical algorithms are of difficult implementation, even considering off-line acquired data as pseudo-measurements. However, the necessity of automating the operation of distribution networks, mainly in regard to the selectivity of protection systems, as well to implement possibilities of load transfer maneuvers, is changing the network planning policy. In this way, some equipments incorporating telemetry and command modules have been installed in order to improve operational features, and so increasing the amount of measurement data available in real-time in the System Operation Center (SOC). This encourages the development of a state estimator model, involving real-time information and pseudo-measurements of loads, that are built from typical power factors and utilization factors (demand factors) of distribution transformers. This work reports about the development of a new state estimation method, specific for radial distribution systems. The main algorithm of the method is based on the power summation load flow. The estimation is carried out piecewise, section by section of the feeder, going from the substation to the terminal nodes. For each section, a measurement model is built, resulting in a nonlinear overdetermined equations set, whose solution is achieved by the Gaussian normal equation. The estimated variables of a section are used as pseudo-measurements for the next section. In general, a measurement set for a generic section consists of pseudo-measurements of power flows and nodal voltages obtained from the previous section or measurements in real-time, if they exist -, besides pseudomeasurements of injected powers for the power summations, whose functions are the load flow equations, assuming that the network can be represented by its single-phase equivalent. The great advantage of the algorithm is its simplicity and low computational effort. Moreover, the algorithm is very efficient, in regard to the accuracy of the estimated values. Besides the power summation state estimator, this work shows how other algorithms could be adapted to provide state estimation of middle voltage substations and networks, namely Schweppes method and an algorithm based on current proportionality, that is usually adopted for network planning tasks. Both estimators were implemented not only as alternatives for the proposed method, but also looking for getting results that give support for its validation. Once in most cases no power measurement is performed at beginning of the feeder and this is required for implementing the power summation estimations method, a new algorithm for estimating the network variables at the middle voltage bus-bar was also developed

Uso de técnicas de otimização baseadas em derivadas como suporte do planejamento operacional de redes de distribuição de energia elétrica

The usual programs for load flow calculation were in general developped aiming the simulation of electric energy transmission, subtransmission and distribution systems. However, the mathematical methods and algorithms used by the formulations were based, in majority, just on the characteristics of the transmittion systems, which were the main concern focus of engineers and researchers. Though, the physical characteristics of these systems are quite different from the distribution ones. In the transmission systems, the voltage levels are high and the lines are generally very long. These aspects contribute the capacitive and inductive effects that appear in the system to have a considerable influence in the values of the interest quantities, reason why they should be taken into consideration. Still in the transmission systems, the loads have a macro nature, as for example, cities, neiborhoods, or big industries. These loads are, generally, practically balanced, what reduces the necessity of utilization of three-phase methodology for the load flow calculation. Distribution systems, on the other hand, present different characteristics: the voltage levels are small in comparison to the transmission ones. This almost annul the capacitive effects of the lines. The loads are, in this case, transformers, in whose secondaries are connected small consumers, in a sort of times, mono-phase ones, so that the probability of finding an unbalanced circuit is high. This way, the utilization of three-phase methodologies assumes an important dimension. Besides, equipments like voltage regulators, that use simultaneously the concepts of phase and line voltage in their functioning, need a three-phase methodology, in order to allow the simulation of their real behavior. For the exposed reasons, initially was developped, in the scope of this work, a method for three-phase load flow calculation in order to simulate the steady-state behaviour of distribution systems. Aiming to achieve this goal, the Power Summation Algorithm was used, as a base for developping the three phase method. This algorithm was already widely tested and approved by researchers and engineers in the simulation of radial electric energy distribution systems, mainly for single-phase representation. By our formulation, lines are modeled in three-phase circuits, considering the magnetic coupling between the phases; but the earth effect is considered through the Carson reduction. Its important to point out that, in spite of the loads being normally connected to the transformers secondaries, was considered the hypothesis of existence of star or delta loads connected to the primary circuit. To perform the simulation of voltage regulators, a new model was utilized, allowing the simulation of various types of configurations, according to their real functioning. Finally, was considered the possibility of representation of switches with current measuring in various points of the feeder. The loads are adjusted during the iteractive process, in order to match the current in each switch, converging to the measured value specified by the input data. In a second stage of the work, sensibility parameters were derived taking as base the described load flow, with the objective of suporting further optimization processes. This parameters are found by calculating of the partial derivatives of a variable in respect to another, in general, voltages, losses and reactive powers. After describing the calculation of the sensibility parameters, the Gradient Method was presented, using these parameters to optimize an objective function, that will be defined for each type of study. The first one refers to the reduction of technical losses in a medium voltage feeder, through the installation of capacitor banks; the second one refers to the problem of correction of voltage profile, through the instalation of capacitor banks or voltage regulators. In case of the losses reduction will be considered, as objective function, the sum of the losses in all the parts of the system. To the correction of the voltage profile, the objective function will be the sum of the square voltage deviations in each node, in respect to the rated voltage. In the end of the work, results of application of the described methods in some feeders are presented, aiming to give insight about their performance and acuity

Implementação de processador banda base ofdma para downlink lte em fpga

This work treats of an implementation OFDMA baseband processor in hardware for LTE Downlink. The LTE or Long Term Evolution consist the last stage of development of the technology called 3G (Mobile System Third Generation) which offers an increasing in data rate and more efficiency and flexibility in transmission with application of advanced antennas and multiple carriers techniques. This technology applies in your physical layer the OFDMA technical (Orthogonal Frequency Division Multiple Access) for generation of signals and mapping of physical resources in downlink and has as base theoretical to OFDM multiple carriers technique (Orthogonal Frequency Division Multiplexing). With recent completion of LTE specifications, different hardware solutions have been developed, mainly, to the level symbol processing where the implementation of OFDMA processor in base band is commonly considered, because it is also considered a basic architecture of others important applications. For implementation of processor, the reconfigurable hardware offered by devices as FPGA are considered which shares not only to meet the high requirements of flexibility and adaptability of LTE as well as offers possibility of an implementation quick and efficient. The implementation of processor in reconfigurable hardware meets the specifications of LTE physical layer as well as have the flexibility necessary for to meet others standards and application which use OFDMA processor as basic architecture for your systems. The results obtained through of simulation and verification functional system approval the functionality and flexibility of processor implemented

Desenvolvimento de um Sistema de Automação e Supervisão de Máquinas Dispensadoras Através da Internet

This paper aims to design and develop a control and monitoring system of vending machines, based on a Central Processing Unit with peripheral Internet communication. Coupled with the condom vending machines, a data acquisition module will be connected to the original circuits in order to collect and send, via internet, the information to the healthy government agencies, in the form of charts and reports. In the face of this, such agencies may analyze these data and compare them with the rates of reduction, in medium or long term, of the STD/AIDS in their respective regions, after the implementation of these vending machines, together with the conventional preventing programs. Reading the methodology, this paper is about an explaining and bibliography research, with the aspect of a qualitative-quantitative methodology, presenting a deductive method of approach and an indirect documentation technique research. About the results of the tests and simulations, we concluded that the implementation of this system will have the same success in any other type of dispenser machine

Line-pack management for producing electric power on peak periods

The distribution of natural gas is carried out by means of long ducts and intermediate compression stations to compensate the pressure drops due to friction. The natural gas compressors are usually driven by an electric motor or a gas turbine system, offering possibilities for energy management, one of these consisting in generating energy for use in-plant or to commercialize as independent power producer. It can be done by matching the natural gas demand, at the minimum pressure allowed in the reception point, and the storage capacity of the feed duct with the maximum compressor capacity, for storing the natural gas at the maximum permitted pressure. This allows the gas turbine to drive an electric generator during the time in which the decreasing pressure in duct is above the minimum acceptable by the sink unit. In this paper, a line-pack management analysis is done for an existing compression station considering its actual demand curve for determining the economic feasibility of maintaining the gas turbine system driver generating electricity in a peak and off-peak tariff structure. The potential of cost reduction from the point of view of energy resources (natural gas and electric costs) is also analyzed. (C) 2010 Elsevier Ltd. All rights reserved.

Estruturação litosférica da Província Borborema ao longo da Transecta Angüera (BA) Macau (RN), com base em dados gravimétricos

Since 2005, geophysical surveys have been carried out in the Precambri-an Borborema Province, along two transects with 800 km long each one. A pool of Brazilian public universities and institutions has been acquired deep refrac-tion seismic, gravity and magnetotelluric, with the purpose to model the conti-nental lithosphere of the region. This paper present the gravity survey of the second transect, that crosses the Borborema Province from SW to NE, passing through the São Francisco Craton, Transversal and Meridional zones and Rio Grande do Norte Domain, in the Setentrional Zone. In this way, it cuts some important geologic structures, like the limit of the São Francis Craton and the Borborema Province, Paleozoic and Mesozoic sedimentary basins of Tucano, Jatobá and Potiguar and the extensive Pernambuco and Patos shear zones. Recognition techniques gravity sources in the subsurface, such as spectral analysis and Euler Deconvolution, were applied to the Bouguer anomalies, as well as their regional and residual components. These techniques provided in-formation on possible anomalous bodies, which correlated with pre-existing geological and geophysical data, subsidized a 2.5 D gravity modeling of the lithosphere beneath the Borborema Province and its southern limit with the São Francisco Craton.

Effect of monomer treatment and polymerisation methods on the bond strength of resin teeth to denture base material

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Hardness of heat-polymerized acrylic resins after disinfection and long-term water immersion

Statement of the problem. In selecting a disinfectant for dental prostheses, compatibility between the disinfectant and the type of denture base material must be considered to avoid adverse effects on the hardness of the acrylic resin.Purpose. This study investigated the hardness of 2 denture base resins after disinfection and long-term water immersion.Material and methods. Thirty-two disk-shaped specimens (13 mm in diameter and 8 mm thick) were fabricated from each resin (Lucitone 550 and QC-20), polished, stored in water at 37degreesC for 48 hours, and submitted to hardness tests (Vickers hardness number [VHN]) before disinfection. Disinfection methods included scrubbing with 4% chlorhexidine gluconate for 1 minute, immersion for 10 minutes in I of the tested disinfectant Solutions (n=8) (3.78% sodium perborate, 4% chlorhexidine gluconate, or 1% sodium hypochorite), and immersion in water for 3 minutes. The disinfection procedures were repeated 4 times, and 12 hardness measurements were made on each specimen. Control specimens (not disinfected) were stored in water for 56 minutes. Hardness tests (VHN) were also performed after 15, 30, 60, 90, and 120 days of storage in water. Statistical analyses of data were conducted with a repeated measures 3-way analysis of variance (ANOVA) and Tukey post-hoc test (alpha=.05).Results. Mean values +/- SD for Lucitone 550 (16.52 +/- 0.94 VHN) and QC-20 (9.61 +/- 0.62 VHN) demonstrated a significant (P<.05) decrease in hardness after disinfection, regardless of material and disinfectant solutions used (Lucitone 550: 15.25 +/- 0.74; QC-20: 8.09 +/- 0.39). However, this effect was reversed after 15 days of storage in water. Both materials exhibited a continuous increase (P<.05) in hardness values for up to 60 days of water storage, after which no significant change was observed.Conclusion. Within the limitations of this in vitro study, QC-20 and Lucitone 550 specimens exhibited significantly lower hardness values after disinfection regardless of the disinfectant solution used.

Chave de identificação de espécies do estrato arbóreo da Mata Atlântica em Ubatuba (SP), com base em caracteres vegetativos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)