An All-E-Beam Lithography Process for the Patterning of 2D Photonic Crystal Waveguide Devices

We present an all-e-beam lithography (EBL) process for the patterning of photonic crystal waveguides.The whole device structures are exposed in two steps. Holes constituting the photonic crystal lattice and defects are first exposed with a small exposure step size (less than 10nm). With the introduction of the additional proximity effect to compensate the original proximity effect, the shape, size, and position of the holes can be well controlled.The second step is the exposure of the access waveguides at a larger step size (about 30nm) to improve the scan speed of the EBL. The influence of write-field stitching error can be alleviated by replacing the original waveguides with tapered waveguides at the joint of adjacent write-fields. It is found experimentally that a higher exposure efficiency is achieved with a larger step size;however,a larger step size requires a higher dose.

Low-Microwave Loss Coplanar Waveguides Fabricated on High-Resistivity Silicon Substrate

Three kinds of coplanar waveguides （CPWs） are designed and fabricated on different silicon substrates---common low-resistivity silicon substrate （LRS）, LRS with a 3μm-thick silicon oxide interlayer, and high-resistivity silicon （HRS） substrate. The results show that the microwave loss of a CPW on LRS is too high to be used, but it can be greatly reduced by adding a thick interlayer of silicon oxide between the CPW transmission lines and the LRS.A CPW directly on HRS shows a loss lower than 2dB/cm in the range of 0-26GHz and the process is simple,so HRS is a more suitable CPW substrate.

An Electroabsorption Modulator Monolithically Integrated with a Semiconductor Optical Amplifier and a Dual-Waveguide Spot-Size Converter

A semiconductor optical amplifier and electroabsorption modulator monolithically integrated with a spotsize converter input and output is fabricated by means of selective area growth,quantum well intermixing,and asymmetric twin waveguide technology. A 1550-1600nm lossless operation with a high DC extinction ratio of 25dB and more than 10GHz 3dB bandwidth are successfully achieved. The output beam divergence angles of the device in the horizontal and vertical directions are as small as 7.3°× 18.0°, respectively, resulting in a 3.0dB coupling loss with a cleaved single-mode optical fiber.

Monolithically Integrated Laser Diode and Electroabsorption Modulator with Dual-Waveguide Spot-Size Converter Output

A 1.60μm laser diode and electroabsorption modulator monolithically integrated with a novel dualwaveguide spot-size converter output for low-loss coupling to a cleaved single-mode optical fiber are demonstrated.The devices emit in a single transverse and quasi single longitudinal mode with an SMSR of 25.6dB. These devices exhibit a 3dB modulation bandwidth of 15. 0GHz, and modulator DC extinction ratios of 16.2dB. The output beam divergence angles of the spot-size converter in the horizontal and vertical directions are as small as 7. 3°× 18. 0°,respectively, resulting in a 3. 0dB coupling loss with a cleaved single-mode optical fiber.

Design,Fabrication,and Testing of Single-Side Alignment of 16×0.8nm Arrayed-Waveguide Grating

A novel design of 100GHz-spaced 16channel arrayed-waveguide grating (AWG) based on silica-on-silicon chip is reported.AWG is achieved by adding a Y-branch to the AWG and arranging the input/output channel in a neat row,so the whole configuration can be aligned and packaged using only one fiber-array.This configuration can decrease the device's size,enlarge the minimum radius of curvature,save time on polishing and alignment,and reduce the chip's fabrication cost.

Analysis and Simulation of S-shaped Waveguide in Silicon-on-insulator

The simulation and analysis of S-shaped waveguide bend are presented.Bend radius larger than 30 mm assures less than 0.5 dB radiation loss for a 4-μm-wide silicon-on-insulator waveguide bend with 2-μm etch depth.Intersection angle greater than 20° provides negligible crosstalk (＜-30 dB) and very low insertion loss.Any reduction in bend radius and intersection angle is at the cost of the degradation of characteristics of bent waveguide and intersecting waveguide, respectively.

Polarization-Insensitive Silica on Silicon Arrayed Waveguide Grating Design

A new technology for fabrication of silica on silicon arrayed waveguide grating (AWG) based on deep etching and thermal oxidation is presented.Using this method,a silicon layer is remained at the side of waveguide.The stress distribution and effective refractive index of waveguide fabricated by this approach are calculated using finite element and finite difference beam propagation method,respectively.The results of these studies indicate that the stress of silica on silicon optical waveguide can be matched in parallel and vertical direction and AWG polarization dependent wavelength (PDλ) can be reduced effectively due to side-silicon layer.

High Power 940 nm Al-free Active Region Laser Diodes and Bars with a Broad Waveguide

The 940 nm Al-free active region laser diodes and bars with a broad waveguide were designed and fabricated. The stuctures were grown by metal organic chemical vapour deposition. The devices show excellent performances. The maximum output power of 6.7 W in the 100 f^m broad-area laser diodes has been measured, and is 2. 5 times higher than that in the Al-containing active region laser diodes with a narrow waveguide and 1. 7 times higher than that in Al-free active region laser diodes with a narrow waveguide. The 19 % fill-factor laser diode bars emit 33 W, and they can operate at 15W with low degradation rates.

Self-aligned Coupled Waveguide Distributed Bragg Reflector Lasers

A novel self-aligned coupled waveguide (SACW) multi-quantum-well (MQW) distributed Bragg reflector (DBR) laser is proposed and demonstrated for the first time. By selectively removing the MQW layer and leaving the low SCH/SACW layer the Bragg grating is partially formed on this layer. By optimizing the thickness of the low SCH/SACW layer, a ～80% coupling efficiency between the MQW gain region and the passive region are obtained. The typical threshold current of the SACW DBR laser is 39 mA, the slope efficiency can reach to 0.2 mW/mA and the output power is more than 20 mW with a more than 30dB side mode suppression ratio.

High Power 808nm AlGaAs/GaAs Quantum Well Laser Diodes with Broad Waveguide

The 808nm laser diodes with a broad waveguide are designed and fabricated. The thickness of the Al_(0.35)-Ga_(0.65)As waveguide is increased to 0.9μm. In order to suppress the super modes, the thickness of the Al_(0.55)Ga_(0.45)As cladding layers is reduced to only 0.7μm while keeping the transverse radiation losses of the fundamental mode below 0.2cm~(-1). The structures are grown by metal organic chemical vapour deposition. The devices show excellent performances. The maximum output power of 10.2W in the 100μm broad-area laser diodes is obtained.

Arrayed-Waveguide Layout for AWG Design

于2010-11-23批量导入

Optim ization of a 1×8 Arrayed-Waveguide Grating Multi/Dem ultiplexer

于2010-11-23批量导入

Novel High Power Quantum WellLasers With Integrated Passive Waveguide

国家自然科学基金

Effects of non-abrupt interface on waveguide properties of sitle/Si MQW photodetector

于2010-11-23批量导入