A direct digital frequency synthesizer with single-stage delta-sigma interpolator and current-steering DAC

This paper presents a direct digital frequency synthesizer (DDFS) with a 16-bit accumulator, a 4th-order single-stage pipelined delta-sigma interpolator and a 300MS/s 12-bit current-steering DAC based on Q(2) Random Walk switching scheme. The delta-sigma interpolator is used to reduce the phase truncation error and the ROM size. The measured spurious-free dynamic range (SFDR) is greater than 80 dB for 8-bit phase value and 12-bit sine-amplitude output. The DDFS prototype is fabricated in a 0.35um CMOS technology with core area of 1.11mm(2).

A direct digital frequency synthesizer with fourth-order phase domain Delta Sigma noise shaper and 12-bit current-steering DAC

This paper presents a direct digital frequency synthesizer (DDFS) with a 16-bit accumulator, a fourth-order phase domain single-stage Delta Sigma interpolator, and a 300-MS/s 12-bit current-steering DAC based on the Q(2) Random Walk switching scheme. The Delta Sigma interpolator is used to reduce the phase truncation error and the ROM size. The implemented fourth-order single-stage Delta Sigma noise shaper reduces the effective phase bits by four and reduces the ROM size by 16 times. The DDFS prototype is fabricated in a 0.35-mu m CMOS technology with active area of 1.11 mm(2) including a 12-bit DAC. The measured DDFS spurious-free dynamic range (SFDR) is greater than 78 dB using a reduced ROM with 8-bit phase, 12-bit amplitude resolution and a size of 0.09 mm(2). The total power consumption of the DDFS is 200)mW with a 3.3-V power supply.

A Smart Frequency Presetting Technique for Fast Lock-in LC-PLL Frequency Synthesizer

This paper proposes a smart frequency presetting technique for fast lock-in LC-PLL frequency synthesizer. The technique accurately presets the frequency of VCO with small initial frequency error and greatly reduces the lock-in time. It can automatically compensate preset frequency variation with process and temperature. A 2.4GHz synthesizer with 1MHz reference input was implemented in 0.35 mu m CMOS process. The chip core area is 0.4mm(2). Output frequency of VCO ranges from 2390 to 2600MHz. The measured results show that the typical lock-in time is 3 mu s. The phase noise is -112dBc/Hz at 600KHz offset from center frequency. The test chip consumes current of 22mA that includes the consumption of the I/O buffers.

Coherent laser control in attosecond sum-frequency polarization beats using twin noisy driving fields

Based on the phase-conjugate polarization interference between two-pathway excitations, we obtained an analytic closed form for the second-order or fourth-order Markovian stochastic correlation of the V three-level sum-frequency polarization beat (SFPB) in attosecond scale. Novel interferometric oscillatory behavior is exposed in terms of radiation-radiation, radiation-matter, and matter-matter polarization beats. The phase-coherent control of the light beams in the SFPB is subtle. When the laser has broadband linewidth, the homodyne detected SFPB signal shows resonant-nonresonant cross correlation, a drastic difference for three Markovian stochastic fields, and the autocorrelation of the SFPB exhibits hybrid radiation-matter detuning terahertz damping oscillation. As an attosecond ultrafast modulation process, it can be extended intrinsically to any sum frequency of energy levels. It has been also found that the asymmetric behaviors of the polarization beat signals due to the unbalanced controllable dispersion effects between the two arms of interferometer do not affect the overall accuracy in case using the SFPB to measure the Doppler-free energy-level sum of two excited states.

A high speed direct digital frequency synthesizer realized by a segmented nonlinear DAC

This paper presents a high speed ROM-less direct digital frequency synthesizer (DDFS) which has a phase resolution of 32 bits and a magnitude resolution of 10 bits. A 10-bit nonlinear segmented DAC is used in place of the ROM look-up table for phase-to-sine amplitude conversion and the linear DAC in a conventional DDFS.The design procedure for implementing the nonlinear DAC is presented. To ensure high speed, current mode logic (CML) is used. The chip is implemented in Chartered 0.35μm COMS technology with active area of 2.0 × 2.5 mm~2 and total power consumption of 400 mW at a single 3.3 V supply voltage. The maximum operating frequency is 850 MHz at room temperature and 1.0 GHz at 0 ℃.

A Compact Direct Digital Frequency Synthesizer for the Rubidium Atomic Frequency Standard

A compact direct digital frequency synthesizer （DDFS） for system-on-chip implementation of the high precision rubidium atomic frequency standard is developed. For small chip size and low power consumption, the phase to sine mapping data is compressed using sine symmetry technique, sine-phase difference technique, quad line approximation technique,and quantization and error read only memory （QE-ROM） technique. The ROM size is reduced by 98% using these techniques. A compact DDFS chip with 32bit phase storage depth and a 10bit on-chip digital to analog converter has been successfully implemented using a standard 0.35μm CMOS process. The core area of the DDFS is 1.6mm^2. It consumes 167mW at 3.3V,and its spurious free dynamic range is 61dB.

Blue-violet luminescence double peak of In-doped films prepared by radio frequency sputtering

ZnO films doped with different contents of indium were prepared by radio frequency sputtering technique. The structural, optical and emission properties of the films were characterized at room temperature using XRD, XPS, UV-vis-NIR and PL techniques. Results showed that the indium was successfully incorporated into the c-axis preferred orientated ZnO films, and the In-doped ZnO films are of over 80% optical transparency in the visible range. Furthermore, a double peak of blue-violet emission with a constant energy interval (similar to 0.17 eV) was observed in the PL spectra of the samples with area ratio of indium chips to the Zn target larger than 2.0%. The blue peak comes from the electron transition from the Zn-i level to the top of the valence band and the violet peak from the In-Zn donor level to the V-Zn level, respectively.

Influence of Inter-Fiber Spacing and Interfacial Adhesion on Failure of Multi-Fiber Model Composites: Experiment and Numerical Analysis

The uniaxial tension experiments on glass-fiber-reinforced epoxy matrix composites reveal that the fragmentations of fibers display vertically aligned fracture, clustered fracture, coordinated fracture, and random fracture with the increase of inter-fiber spacing. The finite element analysis indicates that the fragmentations of fibers displaying different phenomena are due to the stress concentration as well as the inherent randomness of fiber defects, which is the dominant factor. The experimental results show that matrices adjacent to the fiber breakpoints all exhibit birefringent-whitening patterns for the composites with different interfacial adhesion strengths. The larger the extent of the interfacial debonding, the less the domain of the birefringent-whitening patterns. The numerical analysis indicates that the orientation of the matrix adjacent to a fiber breakpoint is caused by the interfacial shear stress, resulting in the birefringent-whitening patterns. The area of shear stress concentrations decides on the domain of the birefringent-whitening patterns.

Colloid chemical approach to nanoelectrode ensembles with highly controllable active area fraction

A novel "bottom-up" approach to highly controllable nanoelectrode ensembles (NEEs) has been developed using colloidal nanoparticle self-assembly techniques. Ibis solution-based strategy allows flexible control over nanoelectrode size, shape, and interspacing of the as-prepared NEEs. Atomic force microscopy (AFM) was proved to be a powerful tool to monitor the NEE topography, which yields parameters that can be used to calculate the fractional nanoelectrode area of the NEEs. AFM, ac impedance, and cyclic voltammetry studies demonstrate that most of nanoelectrodes on the NEEs (at least by 9-min self-assembly) are not diffusionally isolated under conventional ac frequency range and scan rates. As a result, the NEEs behave as "nanoelectrode-patch" assemblies. Besides, the as-prepared NEEs by different self-assembling times show an adjustable sensitivity to heterogeneous electron-transfer kinetics, which may be helpful to sensor applications. Like these NEEs constructed by other techniques, the present NEEs prepared by chemical self-assembly also exhibit the enhancement of electroanalytical detection limit consistent with NEE theory prediction.

Simultaneous determination of both the calibration constant in an electrochemical quartz crystal microbalance and the active surface area of a polycrystalline gold electrode

A novel method is employed for the simultaneous determination of both the calibration constant of an electrochemical quartz crystal microbalance (EQCM) and the active surface area of a polycrystalline gold electrode. A gold electrode: is immersed into a 1 mM KI/1 M H2SO4 solution and on which forms a neutral monolayer. The adsorbed iodine can then be completely oxidized into IO3-. The active surface area of a gold electrode can be obtained from the net electrolytic charge of the oxidation process, and the calibration constant in the EQCM can be calculated from the corresponding frequency shift. The result shows that this method is simple, convenient and valid. (C) 2000 Elsevier Science S.A. All rights reserved.

大气季节内振荡对东亚夏季风活动的影响研究

利用ERA40逐日再分析资料、NCEP/NCAR2逐日再分析资料、中国740个测站日降水资料、上海台风研究所提供的西太平洋热带气旋资料、Kaplan等重建的月平均SSTA资料、NOAA逐日长波辐射（OLR）等资料，应用离散功率谱分析、带通滤波、EOF分析等统计方法，研究了东亚夏季风(EASM）的移动特征、东亚地区季节内振荡(ISO)的基本特征、季节内振荡对东亚夏季风活动的影响、季节内振荡对东亚夏季风异常活动的影响机理。主要结论如下： （1）综合动力和热力因素定义了可动态描述东亚夏季风移动和强度的指数，并利用该指数研究了东亚夏季风的爆发和移动的季节内变化及其年际和年代际变化特征。研究发现，气候平均东亚夏季风前沿分别在28候、33候、36候、38候、40候、44候出现了明显的跳跃。东亚夏季风活动具有显著的年际变率，主要由于季风前沿在某些区域异常停滞和突然跨越北跳或南撤引起，造成中国东部旱涝灾害频繁发生。东亚夏季风的活动具有明显的年代际变化，在1965年、1980年、1994年发生了突变，造成中国东部降水由“南旱北涝”向“南涝北旱”的转变。 （2）东亚季风区季节内变化具有10~25d和30~60d两个波段的季节内振荡周期，以30-60d为主。存在三个主要低频模态，第一模态主要表征了EASM在长江中下游和华北地区活动期间的低频形势；第二模态印度洋-菲律宾由低频气旋式环流控制，主要表现了ISO在EASM爆发期间的低频形势；第三模态主要出现在EASM在华南和淮河活动期间的低频形势。第一模态和第三模态是代表东亚夏季风活动异常的主要低频形势。 （3）热带和副热带地区ISO总是沿垂直切变风的垂直方向传播。因此，在南海-菲律宾东北风垂直切变和副热带西太平洋北风垂直切变下，大气热源激发菲律宾附近交替出现的低频气旋和低频反气旋不断向西北传播，副热带西太平洋ISO以向西传播为主。中高纬度地区，乌拉尔山附近ISO以向东、向南移动或局地振荡为主；北太平洋中部ISO在某些情况下向南、向西传播。 （4）季风爆发期，伴随着热带东印度洋到菲律宾一系列低频气旋和低频反气旋， 冷空气向南输送，10~25天和30~60天季节内振荡低频气旋同时传入南海加快了南海夏季风的爆发。在气候态下，ISO活动表现的欧亚- 太平洋（EAP）以及太平洋-北美（PNA）低频波列分布特征(本文提出的EAP和PNA低频波列与传统意义上的二维定点相关得到的波列不同)。这种低频分布形式使得欧亚和太平洋中高纬度的槽、脊及太平洋副热带高压稳定、加强，东亚地区的低频波列则成为热带和中高纬度ISO相互作用影响东亚夏季风活动的纽带。不同的阶段表现不同的低频模态，30~60d低频模态的转变加快了EASM推进过程中跳跃性；30-60d低频模态的维持使得EASM前沿相对停滞。 （5）30-60d滤波场，菲律宾海域交替出现的低频气旋和低频反气旋不断向西北传播到南海-西太平洋一带。当南海-西太平洋地区低频气旋活跃时，季风槽加强、东伸，季风槽内热带气旋（TC）频数增加；当南海-西太平洋低频反气旋活跃时，季风槽减弱、西退，TC处于间歇期，生成位置不集中。 （6）在El Nino态下，大气季节内振荡偏弱，北传特征不明显，但ISO由中高纬度北太平洋中部向南和副热带西太平洋向西的传播特征显著，东亚地区ISO活动以第三模态为主，EASM集中停滞在华南和淮河流域，常伴随着持续性区域暴雨的出现，易造成华南和江淮流域洪涝灾害，长江和华北持续干旱。在La Nina态下，大气季节内振荡活跃，且具有明显的向北传播特征，PNA低频波列显著，东亚地区ISO活动以第一模态单峰为主；EASM主要停滞在长江中下游和华北地区，这些地区出现异常持续强降水，华南和淮河流域多干旱；在El Nino态向La Nina态转换期，ISO活动以第一模态双峰为主，长江中下游常常出现二度梅。

碳、氧稳定同位素分析在古环境研究中的应用

A number of proxy records of paleoenvironment using stable isotopes could show the history of past environmental changes. These archives include peat and lake sediments, loess-paleosot sequence, fossil mammals and stalagmite, and so on. The stable isotopic composition of carbonate and organic matter and frequency magnetic susceptibility from Tianshuigou and Yuanlei loess-palesol sequence can be used to give estimates of the paleoenvironmental history of Dali, and even of the whole Chinese Loess Plateau during the last 250ka. Features of the High Temperature and Large Precipitation Event in the Tibet Plateau and its adjacent area during 40~30kaBP had been studied by Professor Shi Y. In this dissertation, its impact on Chinese Loess Plateau has been discussed again. Carbon and oxygen isotopic ratios, magnetic susceptibility and frequency magnetic susceptibility in Tianshuigou and Yuanlei profiles show that the Event in this area is not so stronger as the Tibet Plateau. The carbon isotopic composition of organic matter in Tianshuigou, Yuanlei, dingcun and Jingcun loess-palesol sequences are indicative of major changes in the paleovagetation between terrace and plain of the Chinese Loess Plateau. Water is one of the most important factors adjusting the relative biomass of C4 plant in terrestrial ecosystems. Stable carbon isotope ratio of vertebrate tooth enamel is used increasingly to reconstruct environmental and ecological information modern and ancient ecosystems. The SI3C value of tooth enamel bioapatites can distinguish between browsers and grazers. Data from typical grassland of Inter Mongolia, the Alpine meadow of Qinghai-Tibet Plateau and the Yaluzangbu Great Canyon indicate that diets of mammals could record the relative biomass of C4 plant only in the C4 dominated ecosystem. In a C3 dominated ecosystem, diet of mammals would include more C3 plants than vegetation. According to Professor Cerling, proxy records from North and South America, Africa and Pakistan show that at the end of the Miocene (between 8Ma to 6 Ma) there was a global expansion of CA biomass, probably when atmospheric CO2 levels declined. Thus, "C4 world" and "CO2 starvation" are put forward. In this dissertation, carbon isotopes of fossil tooth such as Equus sanmeniensis and Hipparion chiai from Linxia, China reveal that there is a C3 dominated ecosystem in the late Miocene. Diets of ancient mammals in Linxia are not evidence of global expansion of C4 biomass.

Phase estimation receiver for full-field detection: a novel receiver structure for electronic dispersion compensation of metropolitan area networks

The development of ultra high speed (~20 Gsamples/s) analogue to digital converters (ADCs), and the delayed deployment of 40 Gbit/s transmission due to the economic downturn, has stimulated the investigation of digital signal processing (DSP) techniques for compensation of optical transmission impairments. In the future, DSP will offer an entire suite of tools to compensate for optical impairments and facilitate the use of advanced modulation formats. Chromatic dispersion is a very significant impairment for high speed optical transmission. This thesis investigates a novel electronic method of dispersion compensation which allows for cost-effective accurate detection of the amplitude and phase of the optical field into the radio frequency domain. The first electronic dispersion compensation (EDC) schemes accessed only the amplitude information using square law detection and achieved an increase in transmission distances. This thesis presents a method by using a frequency sensitive filter to estimate the phase of the received optical field and, in conjunction with the amplitude information, the entire field can be digitised using ADCs. This allows DSP technologies to take the next step in optical communications without requiring complex coherent detection. This is of particular of interest in metropolitan area networks. The full-field receiver investigated requires only an additional asymmetrical Mach-Zehnder interferometer and balanced photodiode to achieve a 50% increase in EDC reach compared to amplitude only detection.

Large-area nanopatterning of self-assembled monolayers of alkanethiolates by interferometric lithography.

We demonstrate that interferometric lithography provides a fast, simple approach to the production of patterns in self-assembled monolayers (SAMs) with high resolution over square centimeter areas. As a proof of principle, two-beam interference patterns, formed using light from a frequency-doubled argon ion laser (244 nm), were used to pattern methyl-terminated SAMs on gold, facilitating the introduction of hydroxyl-terminated adsorbates and yielding patterns of surface free energy with a pitch of ca. 200 nm. The photopatterning of SAMs on Pd has been demonstrated for the first time, with interferometric exposure yielding patterns of surface free energy with similar features sizes to those obtained on gold. Gold nanostructures were formed by exposing SAMs to UV interference patterns and then immersing the samples in an ethanolic solution of mercaptoethylamine, which etched the metal substrate in exposed areas while unoxidized thiols acted as a resist and protected the metal from dissolution. Macroscopically extended gold nanowires were fabricated using single exposures and arrays of 66 nm gold dots at 180 nm centers were formed using orthogonal exposures in a fast, simple process. Exposure of oligo(ethylene glycol)-terminated SAMs to UV light caused photodegradation of the protein-resistant tail groups in a substrate-independent process. In contrast to many protein patterning methods, which utilize multiple steps to control surface binding, this single step process introduced aldehyde functional groups to the SAM surface at exposures as low as 0.3 J cm(-2), significantly less than the exposure required for oxidation of the thiol headgroup. Although interferometric methods rely upon a continuous gradient of exposure, it was possible to fabricate well-defined protein nanostructures by the introduction of aldehyde groups and removal of protein resistance in nanoscopic regions. Macroscopically extended, nanostructured assemblies of streptavidin were formed. Retention of functionality in the patterned materials was demonstrated by binding of biotinylated proteins.

A pll based frequency synthesizer in 0.13 um sige bicmos for mb-ofdm uwb systems

With the growing demand for high-speed and high-quality short-range communication, multi-band orthogonal frequency division multiplexing ultra-wide band (MB-OFDM UWB) systems have recently garnered considerable interest in industry and in academia. To achieve a low-cost solution, highly integrated transceivers with small die area and minimum power consumption are required. The key building block of the transceiver is the frequency synthesizer. A frequency synthesizer comprised of two PLLs and one multiplexer is presented in this thesis. Ring oscillators are adopted for PLL implementation in order to drastically reduce the die area of the frequency synthesizer. The poor spectral purity appearing in the frequency synthesizers involving mixers is greatly improved in this design. Based on the specifications derived from application standards, a design methodology is presented to obtain the parameters of building blocks. As well, the simulation results are provided to verify the performance of proposed design.