Wet Oxidation of Concentrated Wastewaters: Process Combination and Reaction Kinetic Modeling

The accumulation of aqueous pollutants is becoming a global problem. The search for suitable methods and/or combinations of water treatment processes is a task that can slow down and stop the process of water pollution. In this work, the method of wet oxidation was considered as an appropriate technique for the elimination of the impurities present in paper mill process waters. It has been shown that, when combined with traditional wastewater treatment processes, wet oxidation offers many advantages. The combination of coagulation and wet oxidation offers a new opportunity for the improvement of the quality of wastewater designated for discharge or recycling. First of all, the utilization of coagulated sludge via wet oxidation provides a conditioning process for the sludge, i.e. dewatering, which is rather difficult to carry out with untreated waste. Secondly, Fe2(SO4)3, which is employed earlier as a coagulant, transforms the conventional wet oxidation process into a catalytic one. The use of coagulation as the post-treatment for wet oxidation can offer the possibility of the brown hue that usually accompanies the partial oxidation to be reduced. As a result, the supernatant is less colored and also contains a rather low amount of Fe ions to beconsidered for recycling inside mills. The thickened part that consists of metal ions is then recycled back to the wet oxidation system. It was also observed that wet oxidation is favorable for the degradation of pitch substances (LWEs) and lignin that are present in the process waters of paper mills. Rather low operating temperatures are needed for wet oxidation in order to destruct LWEs. The oxidation in the alkaline media provides not only the faster elimination of pitch and lignin but also significantly improves the biodegradable characteristics of wastewater that contains lignin and pitch substances. During the course of the kinetic studies, a model, which can predict the enhancements of the biodegradability of wastewater, was elaborated. The model includes lumped concentrations suchas the chemical oxygen demand and biochemical oxygen demand and reflects a generalized reaction network of oxidative transformations. Later developments incorporated a new lump, the immediately available biochemical oxygen demand, which increased the fidelity of the predictions made by the model. Since changes in biodegradability occur simultaneously with the destruction of LWEs, an attempt was made to combine these two facts for modeling purposes.

Assessment of critical competences required in managing end-user driven businesses in a global forest products compa

Työn pääasiallisena tavoitteena on selvittää ydinosaamista, jota tarvitaan kansainvälisen metsäteollisuusyrityksen loppukäyttäjävetoisessa liiketoiminnassa. Lisäksi tavoitteena on laatia kompetenssimalli, jota voidaan käyttää mm. rekrytoinnissa, koulutuksen ja työnkierron suunnittelussa. Tarkoituksena on tarkastella sekä tällä hetkellä että tulevaisuudessa tarvittavia ydinosaamisia. Työ keskittyy myyntihenkilöiden kompetenssien kuvaamiseen. Kirjallisuuden ja asiantuntijoiden haastattelujen avulla on selvitetty. kompetensseihin liittyviä asioita ja käsitteitä, kuten organisaation oppiminen, innovaatiot sekä asiakaslähtöisyys. Tämän jälkeen on kartoitettu case-yrityksen kartonkiyksikön myyntihenkilökunnan kompetensseja. Kompetenssikartoitus on tehty teemahaastattelujen avulla sekä lisäksi on käytetty työn aikana laadittua kompetenssimatriisia. Saatuja tuloksia on verrattu yhden asiakkaan näkemyksiin. Tulosten mukaan kolme tärkeintä tämän hetken kompetenssia ovat: holistinen näkemys asioista, suhteiden rakentaminen ja kielitaito. Tulevaisuuden tärkeimpiä kompetensseja puolestaan ovat: asiakaslähtöisyys, sähköinen kaupankäynti ja suhteiden rakentaminen. Lopuksi on käsitelty yleisiä metsäteollisuuden tulevaisuuden haasteita sekä annettu joitain kehitysideoita kompetenssien kehittämistä varten.

Supporting Business Model Modelling: a Compromise between Creativity and Constraints

Diagrams and tools help to support task modelling in engi- neering and process management. Unfortunately they are unfit to help in a business context at a strategic level, because of the flexibility needed for creative thinking and user friendly interactions. We propose a tool which bridges the gap between freedom of actions, encouraging creativity, and constraints, allowing validation and advanced features.

Describing and Analyzing Information Technology through Total Quality Management and Process Management: Case Stora Enso Newsprint

Laatu on osaltaan vahvistamassa asemaansa liike-elämässä yritysten kilpaillessa kansainvälisillä markkinoilla niin hinnalla kuin laadulla. Tämä suuntaus on synnyttänyt useita laatuohjelmia, joita käytetään ahkerasti yritysten kokonais- valtaisen laatujohtamisen (TQM) toteuttamisessa. Laatujohtaminen kattaa yrityksen kaikki toiminnot ja luo vaatimuksia myös yrityksen tukitoimintojen kehittämiselle ja parantamiselle. Näihin lukeutuu myös tämän tutkimuksen kohde tietohallinto (IT). Tutkielman tavoitteena oli kuvata IT prosessin nykytila. Tutkielmassa laadittu prosessikuvaus pohjautuu prosessijohtamisen teoriaan ja kohdeyrityksen käyttämään laatupalkinto kriteeristöön. Tutkimusmenetelmänä prosessin nykytilan selvittämiseksi käytettiin teemahaastattelutta. Prosessin nykytilan ja sille asetettujen vaatimusten selvittämiseksi haastateltiin IT prosessin asiakkaita. Prosessianalyysi, tärkeimpien ala-prosessien tunnistaminen ja parannusalueiden löytäminen ovat tämän tutkielman keskeisemmät tulokset. Tutkielma painottui IT prosessin heikkouksien ja parannuskohteiden etsimiseen jatkuvan kehittämisen pohjaksi, ei niinkään prosessin radikaaliin uudistamiseen. Tutkielmassa esitellään TQM:n periaatteet, laatutyökaluja sekä prosessijohtamisen terminologia, periaatteet ja sen systemaattinen toteutus. Työ antaa myös kuvan siitä, miten TQM ja prosessijohtaminen niveltyvät yrityksen laatutyössä.

“Of Spitzenkandidaten and European Leaders”: Is the new 2014 "politicized” Presidency of the Commission going to be a real step forward in the EU legitimization process?

Thanks to ART.17.7 of the Lisbon Treaty, the European Council now has to “take into account” the results of EP Elections when selecting a candidate for the role of Commission President. The European Parliament has grabbed the opportunity to launch the first electoral race for spitzenkandidaten to the Presidency. Is this the start of a new democratizing (and thus, politicizing) process for the European Union? This dissertation will try to give a possible answer to the dilemma by constructing a comprehensive framework around EP Elections 2014 that will involve both the Commission and the Parliament and an analysis of the debate beyond legal provisions and the possibility of a politicized presidency of the Commission.

The new final Clinical Skills examination in human medicine in Switzerland: Essential steps of exam development, implementation and evaluation, and central insights from the perspective of the national Working Group.

OBJECTIVE: Since 2011, the new national final examination in human medicine has been implemented in Switzerland, with a structured clinical-practical part in the OSCE format. From the perspective of the national Working Group, the current article describes the essential steps in the development, implementation and evaluation of the Federal Licensing Examination Clinical Skills (FLE CS) as well as the applied quality assurance measures. Finally, central insights gained from the last years are presented. METHODS: Based on the principles of action research, the FLE CS is in a constant state of further development. On the foundation of systematically documented experiences from previous years, in the Working Group, unresolved questions are discussed and resulting solution approaches are substantiated (planning), implemented in the examination (implementation) and subsequently evaluated (reflection). The presented results are the product of this iterative procedure. RESULTS: The FLE CS is created by experts from all faculties and subject areas in a multistage process. The examination is administered in German and French on a decentralised basis and consists of twelve interdisciplinary stations per candidate. As important quality assurance measures, the national Review Board (content validation) and the meetings of the standardised patient trainers (standardisation) have proven worthwhile. The statistical analyses show good measurement reliability and support the construct validity of the examination. Among the central insights of the past years, it has been established that the consistent implementation of the principles of action research contributes to the successful further development of the examination. CONCLUSION: The centrally coordinated, collaborative-iterative process, incorporating experts from all faculties, makes a fundamental contribution to the quality of the FLE CS. The processes and insights presented here can be useful for others planning a similar undertaking.

Salesperson's customer orientation in the personal selling process and in the use of personal selling techniques in the business-to-business setting

Selling is much maligned, often under-valued subject whose inadequate showing in business schools is in inverse proportion to the many job opportunities it offers and the importance of salespeople bringing incomes to companies. The purpose of this research is to increase the understanding of customer-oriented selling and examine the influence of customer-oriented philosophy on selling process, the applicability of selling techniques to this philosophy and the importance of them to salespeople. The empirical section of the study is two-fold. Firstly, the data of qualitative part was collected by conducting five thematic interviews among sales consultants and case company representatives. The findings of the study indicate that customer-oriented selling requires the activity of salespeople. In the customer-oriented personal selling process, salespeople invest time in the preplanning, the need analysis and the benefit demonstration stages. However, the findings propose that salespeople today must also have the basic capabilities for executing the traditional sales process, and the balance between traditional and consultative selling process will change as the duration of the relationship between the salesperson and customer increases. The study also proposes that selling techniques still belong to the customer-oriented selling process, although their roles might be modest. This thesis mapped 75 selling techniques and the quantitative part of the study explored what selling techniques are considered to be important by salespeople in direct selling industry when they make sales with new and existing customers. Response rate of the survey was 69.5%.

Process approach in quality management - Case: ECO process development in EMS industry

The aim of the thesis was to study quality management with process approach and to find out how to utilize process management to improve quality. The operating environment of organizations has changed. Organizations are focusing on their core competences and networking with suppliers and customers to ensure more effective and efficient value creation for the end customer. Quality management is moving from inspection of the output to prevention of problems from occurring in the first place and management thinking is changing from functional approach to process approach. In the theoretical part of the thesis, it is studied how to define quality, how to achieve good quality, how to improve quality, and how to make sure the improvement goes on as never ending cycle. A selection of quality tools is introduced. Process approach to quality management is described and compared to functional approach, which is the traditional way to manage operations and quality. The customer focus is also studied, and it is presented, that to ensure long term customer commitment, organization needs to react to changing customer requirements and wishes by constantly improving the processes. In the experimental part the theories are tested in a process improvement business case. It is shown how to execute a process improvement project starting from defining the customer requirements, continuing to defining the process ownership, roles and responsibilities, boundaries, interfaces and the actual process activities. The control points and measures are determined for the process, as well as the feedback and corrective action process, to ensure continual improvement can be achieved and to enable verification that customer requirements are fulfilled.

Requirements management process

Vaatimustenhallinnan alue on hyvin kompleksinen. Sen terminologia on moninaista ja samat termit voivat tarkoittaa eri asioita eri ihmisille. Tämän työn tarkoituksena on selkeyttää vaatimustenhallinnan aluetta. Se vastaa kysymyksiin kuten, mitä vaatimustenhallinta on ja miten sitä voidaan tehdä. Työ keskittyy vaatimusten analysoinnin ja validoinnin alueisiin, joten tältä osin se vastaa myös tarkempiin kysymyksiin kuten, miten koottujen vaatimusten jäljitettävyyttä, dokumentointia, analysointia ja validointia voidaan tehdä. Tämän työn kautta vaatimustenhallinta voidaan esitellä yritykselle ja sen eri osat voivat saada saman käsityksen vaatimustenhallinnasta. Tutkimus esittelee vaatimustenhallinnan prosessina, joka pitää sisällään vaatimusten jäljitettävyyden, vaatimusten dokumentoinnin, vaatimusten muutoksenhallinnan ja vaatimusmäärityksen. Vaatimusmääritys voidaan edelleen jakaa vaatimusten koostamiseen, analysointiin ja neuvotteluun sekä validointiin. Työssä esitellään geneerinen vaatimustenhallinnan prosessimalli. Mallin avulla näytetään, että vaatimustenhallinta on jatkuva prosessi, jossa kaikki aktiviteetit ovat kytköksissä toisiinsa. Näitä aktiviteettejä suoritetaan enemmän tai vähemmän samanaikaisesti. Malli esitetään geneerisessä muodossa, jotta se olisi hyödynnettävissä systeemi- ja tuotekehitys projekteissa sekä sisäisissä kehitysprojekteissa. Se kertoo, että vaatimukset tulisi jalostaa niin aikaisin, kuin mahdollista, jotta muutoksien määrä kehitystyön myöhemmissä vaiheissa voitaisiin minimoida. Jotkin muutokset eivät ole vältettävissä, joten muutoksenhallinnan tueksi tulisi kehittää jäljitettävyyskäsikirja ja jäljitettävyyskäytännöt. Vaatimustenhallintaa tarkastellaan meneillään olevassa kehitysprojektissa. Tarkastelussa tutkitaan, mitä vaatimustenhallinnan toimintatapoja sekä analysointi- ja validointimetodeja käytetään ja mitä voitaisiin tehdä vaatimustenhallinnan parantamiseksi projektissa.

Adult education policy in the European Union during the Lisbon decade : the shift to vocational adult learning and work skills matching

This doctoral dissertation investigates the adult education policy of the European Union (EU) in the framework of the Lisbon agenda 2000–2010, with a particular focus on the changes of policy orientation that occurred during this reference decade. The year 2006 can be considered, in fact, a turning point for the EU policy-making in the adult learning sector: a radical shift from a wide--ranging and comprehensive conception of educating adults towards a vocationally oriented understanding of this field and policy area has been observed, in particular in the second half of the so--called ‘Lisbon decade’. In this light, one of the principal objectives of the mainstream policy set by the Lisbon Strategy, that of fostering all forms of participation of adults in lifelong learning paths, appears to have muted its political background and vision in a very short period of time, reflecting an underlying polarisation and progressive transformation of European policy orientations. Hence, by means of content analysis and process tracing, it is shown that the new target of the EU adult education policy, in this framework, has shifted from citizens to workers, and the competence development model, borrowed from the corporate sector, has been established as the reference for the new policy road maps. This study draws on the theory of governance architectures and applies a post-ontological perspective to discuss whether the above trends are intrinsically due to the nature of the Lisbon Strategy, which encompasses education policies, and to what extent supranational actors and phenomena such as globalisation influence the European governance and decision--making. Moreover, it is shown that the way in which the EU is shaping the upgrading of skills and competences of adult learners is modeled around the needs of the ‘knowledge economy’, thus according a great deal of importance to the ‘new skills for new jobs’ and perhaps not enough to life skills in its broader sense which include, for example, social and civic competences: these are actually often promoted but rarely implemented in depth in the EU policy documents. In this framework, it is conveyed how different EU policy areas are intertwined and interrelated with global phenomena, and it is emphasised how far the building of the EU education systems should play a crucial role in the formation of critical thinking, civic competences and skills for a sustainable democratic citizenship, from which a truly cohesive and inclusive society fundamentally depend, and a model of environmental and cosmopolitan adult education is proposed in order to address the challenges of the new millennium. In conclusion, an appraisal of the EU’s public policy, along with some personal thoughts on how progress might be pursued and actualised, is outlined.

Quality, Productivity and Economy in Welding Manufacturing - Case Study: West Africa

This thesis studies quality, productivity and economy in welding manufacturing in West African states such as Ghana, Nigeria and Cameroon. The study consists of two parts: the first part, which forms the theoretical background, reviews relevant literature concerning the metal and welding industries, and measurement of welding quality, productivity and economy. The second part, which is the empirical part, aims to identify activities in the metal manufacturing industries where welding is extensively used and to determine the extent of welding quality, productivity and economy measurements in companies operating in the metal manufacturing industries. Additionally, the thesis aims to identify challenges that companies face and to assess the feasibility of creating a network to address these issues. The research methods used in the empirical part are the case study (qualitative) method and the survey (quantitative) method. However, the case study method was used to elicit information from companies in Ghana, while the survey method was used to elicit information from companies in Nigeria and Cameroon. The study considers important areas that contribute to creating awareness and understanding of the current situation of the welding industry in West Africa. These areas include the metal manufacturing industrial sector, metal products manufactured, metal production and manufacturing systems deployed, welding quality, productivity and economy measurement systems utilized, equipment and materials on the markets, general challenges facing companies in welding operations, welding technology programs and research in local universities, and SWOT analysis of the various West African states. The notable findings indicate that majority of the companies operate in the constructionindustrial sector. Also, majority of the companies are project manufacturing oriented, thus provide services to customers operating in the growing industries such as the oil and gas, mining, food and the energy industry. In addition, only few companies are certified under standards such as ISO 9001, ISO 3834, and OHSAS 18001. More so, majority of the companies employ manual welding technique, and shielded metal arc welding (SMAW) as the commonly used welding process. Finally, welder salary is about € 300 / month as of June 2013 and the average operations turnover of medium to large companies is about € 5 million / year as at 2012. Based on analysis of the results of the study, it is noted that while welding activities are growing, the availability of cheap labor, the need for company and welder qualification and certification, and the need to manufacture innovative products through developmental projects (transfer of welding expertise and technology) remain as untapped opportunities in the welding industry in the West African states. The study serves as a solid platform for further research and concludes with several recommendations for development of the West African welding industry.

Interoperability specifications and an automatic validation tool as a key factor for the support of a repository ecosystem

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Analysis of viral and cellular parameters which affect the fusion process of influenza viruses

In the present investigation we studied the fusogenic process developed by influenza A, B and C viruses on cell surfaces and different factors associated with virus and cell membrane structures. The biological activity of purified virus strains was evaluated in hemagglutination, sialidase and fusion assays. Hemolysis by influenza A, B and C viruses ranging from 77.4 to 97.2%, from 20.0 to 65.0%, from 0.2 to 93.7% and from 9.0 to 76.1% was observed when human, chicken, rabbit and monkey erythrocytes, respectively, were tested at pH 5.5. At this pH, low hemolysis indexes for influenza A, B and C viruses were observed if horse erythrocytes were used as target cells for the fusion process, which could be explained by an inefficient receptor binding activity of influenza on N-glycolyl sialic acids. Differences in hemagglutinin receptor binding activity due to its specificity to N-acetyl or N-glycolyl cell surface oligosaccharides, density of these cellular receptors and level of negative charges on the cell surface may possibly explain these results, showing influence on the sialidase activity and the fusogenic process. Comparative analysis showed a lack of dependence between the sialidase and fusion activities developed by influenza B viruses. Influenza A viruses at low sialidase titers (<2) also exhibited clearly low hemolysis at pH 5.5 (15.8%), while influenza B viruses with similarly low sialidase titers showed highly variable hemolysis indexes (0.2 to 78.0%). These results support the idea that different virus and cell-associated factors such as those presented above have a significant effect on the multifactorial fusion process

VVER-440 Thermal Hydraulics as a Computer Code Validation Challenge

This thesis concentrates on the validation of a generic thermal hydraulic computer code TRACE under the challenges of the VVER-440 reactor type. The code capability to model the VVER-440 geometry and thermal hydraulic phenomena specific to this reactor design has been examined and demonstrated acceptable. The main challenge in VVER-440 thermal hydraulics appeared in the modelling of the horizontal steam generator. The major challenge here is not in the code physics or numerics but in the formulation of a representative nodalization structure. Another VVER-440 specialty, the hot leg loop seals, challenges the system codes functionally in general, but proved readily representable. Computer code models have to be validated against experiments to achieve confidence in code models. When new computer code is to be used for nuclear power plant safety analysis, it must first be validated against a large variety of different experiments. The validation process has to cover both the code itself and the code input. Uncertainties of different nature are identified in the different phases of the validation procedure and can even be quantified. This thesis presents a novel approach to the input model validation and uncertainty evaluation in the different stages of the computer code validation procedure. This thesis also demonstrates that in the safety analysis, there are inevitably significant uncertainties that are not statistically quantifiable; they need to be and can be addressed by other, less simplistic means, ultimately relying on the competence of the analysts and the capability of the community to support the experimental verification of analytical assumptions. This method completes essentially the commonly used uncertainty assessment methods, which are usually conducted using only statistical methods.

Development and validation of a genotype 3 recombinant protein-based immunoassay for hepatitis E virus serology in swine

Hepatitis E virus (HEV) is classified within the family Hepeviridae, genus Hepevirus. HEV genotype 3 (Gt3) infections are endemic in pigs in Western Europe and in North and South America and cause zoonotic infections in humans. Several serological assays to detect HEV antibodies in pigs have been developed, at first mainly based on HEV genotype 1 (Gt1) antigens. To develop a sensitive HEV Gt3 ELISA, a recombinant baculovirus expression product of HEV Gt3 open reading frame-2 was produced and coated onto polystyrene ELISA plates. After incubation of porcine sera, bound HEV antibodies were detected with anti-porcine anti-IgG and anti-IgM conjugates. For primary estimation of sensitivity and specificity of the assay, sets of sera were used from pigs experimentally infected with HEV Gt3. For further validation of the assay and to set the cutoff value, a batch of 1100 pig sera was used. All pig sera were tested using the developed HEV Gt3 assay and two other serologic assays based on HEV Gt1 antigens. Since there is no gold standard available for HEV antibody testing, further validation and a definite setting of the cutoff of the developed HEV Gt3 assay were performed using a statistical approach based on Bayes' theorem. The developed and validated HEV antibody assay showed effective detection of HEV-specific antibodies. This assay can contribute to an improved detection of HEV antibodies and enable more reliable estimates of the prevalence of HEV Gt3 in swine in different regions.