Tracking Human Position and Lower Body Parts Using Kalman and Particle Filters Constrained by Human Biomechanics

In this paper, a novel framework for visual tracking of human body parts is introduced. The approach presented demonstrates the feasibility of recovering human poses with data from a single uncalibrated camera by using a limb-tracking system based on a 2-D articulated model and a double-tracking strategy. Its key contribution is that the 2-D model is only constrained by biomechanical knowledge about human bipedal motion, instead of relying on constraints that are linked to a specific activity or camera view. These characteristics make our approach suitable for real visual surveillance applications. Experiments on a set of indoor and outdoor sequences demonstrate the effectiveness of our method on tracking human lower body parts. Moreover, a detail comparison with current tracking methods is presented.

Systolic array architectures for parameterised multiplexed IIR filters

Whilst conventional bit level pipelining introduces an m cycle delay, it does allow m separate computations to be processed at throughput rates comparable to that using word level systolic arrays. We concentrate on exploiting this delay and describe a systematic method for the design of high performance multiplexed IIR filters. Two multiply and accumulate structures are identified based on shift-and-add and carry-save data organisations which can be used as building blocks in the design of IIR filters. By replacing the word level multiply and accumulate units in word level systolic structures with their equivalent bit level circuits and introducing latches to ensure correct timing, numerous architectures can be designed that process multiplexed data directly without any additional circuit overhead.

SYSTOLIC IIR FILTERS WITH BIT LEVEL PIPELINING.

A novel bit-level systolic array architecture for implementing first-order IIR filter sections is presented. A latency of only two clock cycles is achieved by using a radix-4 redundant number representation, performing the recursive computation most-significant-digit first, and feeding back each digit of the result as soon as it is available.

Bit-level systolic architecture for very high performance IIR filters

A novel bit-level systolic array architecture for implementing bit-parallel IIR filter sections is presented. The authors have shown previously how the fundamental obstacle of pipeline latency in recursive structures can be overcome by the use of redundant arithmetic in combination with bit-level feedback. These ideas are extended by optimizing the degree of redundancy used in different parts of the circuit and combining redundant circuit techniques with those of conventional arithmetic. The resultant architecture offers significant improvements in hardware complexity and throughput rate.

Systematic methodology for the design of high performance recursive digital filters

A systematic design methodology is described for the rapid derivation of VLSI architectures for implementing high performance recursive digital filters, particularly ones based on most significant digit (msd) first arithmetic. The method has been derived by undertaking theoretical investigations of msd first multiply-accumulate algorithms and by deriving important relationships governing the dependencies between circuit latency, levels of pipe-lining and the range and number representations of filter operands. The techniques described are general and can be applied to both bit parallel and bit serial circuits, including those based on on-line arithmetic. The method is illustrated by applying it to the design of a number of highly pipelined bit parallel IIR and wave digital filter circuits. It is shown that established architectures, which were previously designed using heuristic techniques, can be derived directly from the equations described.

3D Analysis of Seepage under Hydraulic Structures with Intermediate Filters

Seepage flow under hydraulic structures provided with intermediate filters has been investigated. The flow through the banks of the canal has been included in the model. Different combinations of intermediate filter and canal width were studied. Different lengths of the floor, differential heads, and depths of the sheet pile driven beneath the floor were also investigated. The introduction of an intermediate filter to the floor of hydraulic structures reduced the uplift force acting on the downstream floor by up to 72%. The maximum uplift reduction occurred when the ratio of the distance of filter location downstream from the cutoff to the differential head was 1. Introducing a second filter in the downstream side resulted in a further reduction in the exit hydraulic gradient and in the uplift force, which reached 90%. The optimum locations of the two filters occurred when the first filter was placed just downstream of the cutoff wall and the second filter was placed nearly at the middistance between the cutoff and the end toe of the floor. The results showed significant differences between the three-dimensional (3D) and the two-dimensional (2D) analyses.

Holistic Design Strategy for High-Selectivity Low-Loss Integrated Millimetre-Wave Image-Reject Filters

To alleviate practical limitations in the design of mm-wave on-chip image-reject filters, systematic design methodologies are presented. Three low-order filters with high-selectivity and low-loss characteristics are designed and compared. Transmission zeroes are created by means of a quarter-wave transmission line (filter 1) and a series LC resonator (filters 2 and 3). Implemented on SiGe, the filters occupy 0.125, 0.064, and 0.079 mm2 chip area including pads. The measured transmission
losses across 81-86 GHz E-Band frequency range are 3.6-5.2 dB for filter 1, 3.1-4.7 dB for filter 2 and 3.6-5 dB for filter 3 where rejection levels at the image band are greater than 30 dB.

Search filters: mapping the literature using a novel form of content analysis.

Background: Search filters are combinations of words and phrases designed to retrieve an optimal set of records on a particular topic (subject filters) or study design (methodological filters). Information specialists are increasingly turning to reusable filters to focus their searches. However, the extent of the academic literature on search filters is unknown. We provide a broad overview to the academic literature on search filters.
Objectives: To map the academic literature on search filters from 2004 to 2015 using a novel form of content analysis.
Methods: We conducted a comprehensive search for literature between 2004 and 2015 across eight databases using a subjectively derived search strategy. We identified key words from titles, grouped them into categories, and examined their frequency and co-occurrences.
Results: The majority of records were housed in Embase (n = 178) and MEDLINE (n = 154). Over the last decade, both databases appeared to exhibit a bimodal distribution with the number of publications on search filters rising until 2006, before dipping in 2007, and steadily increasing until 2012. Few articles appeared in social science databases over the same time frame (e.g. Social Services Abstracts, n = 3).
Unsurprisingly, the term ‘search’ appeared in most titles, and quite often, was used as a noun adjunct for the word 'filter' and ‘strategy’. Across the papers, the purpose of searches as a means of 'identifying' information and gathering ‘evidence’ from 'databases' emerged quite strongly. Other terms relating to the methodological assessment of search filters, such as precision and validation, also appeared albeit less frequently.
Conclusions: Our findings show surprising commonality across the papers with regard to the literature on search filters. Much of the literature seems to be focused on developing search filters to identify and retrieve information, as opposed to testing or validating such filters. Furthermore, the literature is mostly housed in health-related databases, namely MEDLINE, CINAHL, and Embase, implying that it is medically driven. Relatively few papers focus on the use of search filters in the social sciences.

Simple brightness models with low-pass and Gabor filters

A syntactical brightness model based on a multiscale line and edge representation obtained by a set of anisotropic Gabor filters is quite complex (du Buf and Fischer, 1995 Optical Engineering 34 1900-1911). Although only tested in 1-D, it was shown to yield correct brightness effects for many patterns.