The Source of 3 Minute Magnetoacoustic Oscillations in Coronal Fans

We use images of high spatial, spectral, and temporal resolution, obtained using both ground- and space-based instrumentation, to investigate the coupling between wave phenomena observed at numerous heights in the solar atmosphere. Analysis of 4170 Å continuum images reveals small-scale umbral intensity enhancements, with diameters ~0."6, lasting in excess of 30 minutes. Intensity oscillations of ˜3 minutes are observed to encompass these photospheric structures, with power at least three orders of magnitude higher than the surrounding umbra. Simultaneous chromospheric velocity and intensity time series reveal an 87?±8? out-of-phase behavior, implying the presence of standing modes created as a result of partial wave re?ection at the transition region boundary. We ?nd a maximum waveguide inclination angle of˜40? between photospheric and chromospheric heights, combined with a radial expansion factor of <76%. An average blueshifted Doppler velocity of ˜1.5 km s-1, in addition to a time lag between photospheric and chromospheric oscillatory phenomena, con?rms the presence of upwardly propagating slow-mode waves in the lower solar atmosphere. Propagating oscillations in EUV intensity are detected in simultaneous coronal fan structures, with a periodicity of 172±17 s and a propagation velocity of 45±7 km s-1. Numerical simulations reveal that the damping of the magnetoacoustic wave trains is dominated by thermal conduction. The coronal fans are seen to anchor into the photosphere in locations where large-amplitude umbral dot (UD) oscillations manifest. Derived kinetic temperature and emission measure time series display prominent outof-phase characteristics, and when combined with the previously established sub-sonic wave speeds, we conclude that the observed EUV waves are the coronal counterparts of the upwardly propagating magnetoacoustic slow modes detected in the lower solar atmosphere. Thus, for the ?rst time, we reveal how the propagation of 3 minute magnetoacoustic waves in solar coronal structures is a direct result of amplitude enhancements occurring in photospheric UDs.photospheric UDs.

Effects of oscillatory flow on fertilization in the green sea urchin Strongylocentrotus droebachiensis

Broadcast spawning invertebrates that live in shallow, high-energy coastal habitats are subjected to oscillatory water motion that creates unsteady flow fields above the surface of animals. The frequency of the oscillatory fluctuations is driven by the wave period, which will influence the stability of local flow structures and may affect fertilization processes. Using an oscillatory water tunnel, we quantified the percentage of eggs fertilized on or near spawning green sea urchins, Strongylocentrotus droebachiensis. Eggs were sampled in the water column, wake eddy, substratum and aboral surface under a range of different periods (T = 4.5 – 12.7 s) and velocities of oscillatory flow. The root-mean-square wave velocity (rms(uw)) was a good predictor of fertilization in oscillatory flow, although the root-mean-square of total velocity (rms(u)), which incorporates all the components of flow (current, wave and turbulence), also provided significant predictions. The percentage of eggs fertilized varied between 50 – 85% at low flows (rms(uw) < 0.02 m s-1), depending on the location sampled, but declined to below 10% for most locations at higher rms(uw). The water column was an important location for fertilization with a relative contribution greater than that of the aboral surface, especially at medium and high rms(uw) categories. We conclude that gametes can be successfully fertilized on or near the parent under a range of oscillatory flow conditions.

Implementation of phantom-less IMRT delivery verification using Varian DynaLog files and R/V output

This study aims to evaluate the use of Varian radiotherapy dynamic treatment log (DynaLog) files to verify IMRT plan delivery as part of a routine quality assurance procedure. Delivery accuracy in terms of machine performance was quantified by multileaf collimator (MLC) position errors and fluence delivery accuracy for patients receiving intensity modulated radiation therapy (IMRT) treatment. The relationship between machine performance and plan complexity, quantified by the modulation complexity score (MCS) was also investigated. Actual MLC positions and delivered fraction of monitor units (MU), recorded every 50 ms during IMRT delivery, were extracted from the DynaLog files. The planned MLC positions and fractional MU were taken from the record and verify system MLC control file. Planned and delivered beam data were compared to determine leaf position errors with and without the overshoot effect. Analysis was also performed on planned and actual fluence maps reconstructed from the MLC control file and delivered treatment log files respectively. This analysis was performed for all treatment fractions for 5 prostate, 5 prostate and pelvic node (PPN) and 5 head and neck (H&N) IMRT plans, totalling 82 IMRT fields in ∼5500 DynaLog files. The root mean square (RMS) leaf position errors without the overshoot effect were 0.09, 0.26, 0.19 mm for the prostate, PPN and H&N plans respectively, which increased to 0.30, 0.39 and 0.30 mm when the overshoot effect was considered. Average errors were not affected by the overshoot effect and were 0.05, 0.13 and 0.17 mm for prostate, PPN and H&N plans respectively. The percentage of pixels passing fluence map gamma analysis at 3%/3 mm was 99.94 ± 0.25%, which reduced to 91.62 ± 11.39% at 1%/1 mm criterion. Leaf position errors, but not gamma passing rate, were directly related to plan complexity as determined by the MCS. Site specific confidence intervals for average leaf position errors were set at -0.03-0.12 mm for prostate and -0.02-0.28 mm for more complex PPN and H&N plans. For all treatment sites confidence intervals for RMS errors with the overshoot was set at 0-0.50 mm and for the percentage of pixels passing a gamma analysis at 1%/1 mm a confidence interval of 68.83% was set also for all treatment sites. This work demonstrates the successful implementation of treatment log files to validate IMRT deliveries and how dynamic log files can diagnose delivery errors not possible with phantom based QC. Machine performance was found to be directly related to plan complexity but this is not the dominant determinant of delivery accuracy.

Exhibiting Maritime Histories: Titanic Belfast in the Post-Conflict City

The sinking of the RMS Titanic in 1912 represents one of the most infamous maritime disasters in the history of shipping. Yet despite it entering the public imagination in the decades after its sinking, until recently it has all but been erased from the collective memory of the people of Belfast, the city in which it was built. In a post-conflict context, however, Belfast has begun to re-imagine the role of the ship in the city’s history, most particularly in the re-development of the docklands area and its designation as the Titanic Quarter, and through its landmark project the Titanic Belfast museum. This paper will trace the economic, social and political context from which the Titanic was built, and the role that this played in silencing any very public commemoration of its sinking until after the signing of the Belfast Agreement. The ‘story’ told in the new museum will be analysed from this perspective and will illustrate how the wounds of the Troubles continue to inform the interpretation of the city’s divided past.

The influence of water motion on the growth rate of the kelp Laminaria hyperborea

The kelp Laminaria hyperborea is a dominant component of the subtidal nearshore ecosystem and is subjected to a heterogeneous wave and current climate. Water motion is known to influence physiological processes in macroalgae such as photosynthesis and nutrient uptake attributed to mass-transfer limitation. The study attempts to establish the effect of water motion on the growth rates of blades and elongation rates of the stipes of L. hyperborea at adjacent wave-exposed and wave-sheltered locations over a 12month period from field observations. The observations were supported by detailed physical and chemical measurements (light, temperature, seawater nutrient concentrations and hydrodynamics) and of tissue carbon and nitrogen concentrations together with δ¹³carbon. Despite a 30% difference in the root mean square of the velocity (Vel_rms) between the two survey locations, there was no evidence to suggest that water motion had any direct influence on the growth rates of either the blades or elongation of stipes of L. hyperborea. No significant differences were observed between either environmental or plant physiological variables between the sheltered and exposed locations. Using an integral velocity parameter (Vel_rms) the present study also highlighted the importance of the tidally induced current component of water flow in the subtidal zone. 

Body-centric antenna positioning effects for off-body UWB communications in a contemporary learning environment

The propagation of UWB signals for body-centric communications within a modern classroom/conference room environment was investigated. Presented results demonstrate that the body-antenna mounting position has a marked impact on the received power levels and positioning the antenna on the chest as opposed to the shoulder or wrist creates more extreme values in receive power, mean excess delay and rms delay spread. Additionally, the best fit models for each scenario are presented and highlight the difference between the chest and other compared antenna locations. The work concluded that the chest is a poor choice of mounting position for the antenna due to significant body shadowing effects, with the wrist or shoulder considered better options for UWB systems.

Fluence dependence of the surface roughness of InP after N2 + bombardment

InP(1 0 0) surfaces were sputtered under ultrahigh vacuum conditions by 5 keV N2+ ions at an angle of incidence of 41° to the sample normal. The fluence, φ, used in this study, varied from 1 × 10¹⁴ to 5 × 10¹⁸ N2+ cm^-2. The surface topography was investigated using field emission scanning electron microscopy (FE-SEM) and atomic force microscopy (AFM). At the lower fluences (φ ≤ 5 × 10¹⁶ N2+ cm^-2) only conelike features appeared, similar in shape as was found for noble gas ion bombardment of InP. At the higher fluences, ripples also appeared on the surface. The bombardment-induced topography was quantified using the rms roughness. This parameter showed a linear relationship with the logarithm of the fluence. A model is presented to explain this relationship. The ripple wavelength was also determined using a Fourier transform method. These measurements as a function of fluence do not agree with the predictions of the Bradley-Harper theory. © 2004 Elsevier B.V. All rights reserved.

The use of Log-file analysis within VMAT audits

OBJECTIVE: This work investigates the delivery accuracy of different Varian linear accelerator models using log-file derived MLC RMS values.

METHODS: Seven centres independently created a plan on the same virtual phantom using their own planning system and the log files were analysed following delivery of the plan in each centre to assess MLC positioning accuracy. A single standard plan was also delivered by seven centres to remove variations in complexity and the log files were analysed for Varian TrueBeams and Clinacs (2300IX or 2100CD models).

RESULTS: Varian TrueBeam accelerators had better MLC positioning accuracy (<1.0mm) than the 2300IX (<2.5mm) following delivery of the plans created by each centre and also the standard plan. In one case log files provided evidence that reduced delivery accuracy was not associated with the linear accelerator model but was due to planning issues.

CONCLUSIONS: Log files are useful in identifying differences between linear accelerator models, and isolate errors during end-to-end testing in VMAT audits. Log file analysis can rapidly eliminate the machine delivery from the process and divert attention with confidence to other aspects. Advances in Knowledge: Log file evaluation was shown to be an effective method to rapidly verify satisfactory treatment delivery when a dosimetric evaluation fails during end-to-end dosimetry audits. MLC RMS values for Varian TrueBeams were shown to be much smaller than Varian Clinacs for VMAT deliveries.

Conformação automática de formas complexas em vidro de mesa

Os objectivos do presente trabalho foram a investigação dos principais defeitos que ocorrem nos produtos de vidro de mesa produzidos por processos automáticos e o desenvolvimento de novos vidros e tecnologias que permitam aumentar os rendimentos de produção, ou a flexibilidade da operação de conformação. A viscosidade influencia a facilidade de conformação dos produtos. Temperaturas de gota mais baixas, espessuras de parede de produtos mais elevadas e baixas áreas de transferência térmica facilitam a ocorrência de defeitos, sobretudo mecânicos e de superfície. Foram identificados os produtos de vidro de mesa que apresentam maiores dificuldades na conformação, designados por produtos de forma complexa. Por ser um factor relevante na prática, discutiu-se o efeito da quantidade de casco usado na elaboração dos vidros sobre a conformação de produtos de forma complexa. A quantidade de casco influencia a volatilização de fundentes que por sua vez tem efeito sobre as propriedades de trabalhabilidade do vidro. Desenvolveram-se novos vidros compatíveis com a utilização de queimos enriquecidos em oxigénio que são utilizados para reduzirem os defeitos mecânicos e de superfície nos produtos de vidros de mesa prensados. A compatibilidade vidro/tecnologia fez-se com uma modificação do sistema de afinação do vidro. Os vidros modificados apresentam propriedades físicoquímicas semelhantes à do vidro inicial e por isso indicam viabilidade comercial. A tecnologia dos canais corantes foi utilizada para modificar a trabalhabilidade de um vidro base a partir da introdução até 5 % de fritas incolores ricas em Li2O. Os valores de RMS (velocidade relativa de máquina) desceram de 106,8 % para 95,7 % enquanto os valores de Pt (patamar de trabalho) subiram de 100,6 s para 111,3 s com o aumento de frita. As propriedades físico-químicas dos vidros aditivados com frita indicam viabilidade comercial. Esta inovação tecnológica introduz flexibilidade nos processos industriais vidreiros. A composição química do vidro e por isso as propriedades relacionadas com a trabalhabilidade podem ser entendidas como mais uma variável dos processos de conformação e usadas em função das técnicas de conformação disponíveis, da forma dos objectos a conformar e da engenharia da ferramenta moldante utilizada. Foi observada convergência entre os resultados experimentais e os valores calculados a partir dos modelos de Huff e Fluegel nos principais parâmetros da tecnologia vidreira (RMS e Pt) e nas propriedades dos vidros nomeadamente densidade e coeficiente de dilatação térmico. Uma parte importante deste trabalho decorreu em ambiente industrial. Em temas relacionados com a investigação do processamento vidreiro industrial, a prática de desenvolver trabalho experimental integrado no próprio ambiente industrial está claramente documentada na bibliografia publicada em revistas e jornais de referência internacional. ABSTRACT: The research on the causes of major defects that occur in glass tableware products produced by automatic processes and the development of new glasses and technologies for increasing the production efficiency, or the flexibility of operation were the objectives of the Thesis project. Viscosity influences the flexibility of glass forming. Lower drop temperatures, high product wall thicknesses, or low areas of heat transfer facilitate the occurrence of defects, mainly mechanical and surface born. We identified the products of glass tableware showing the greatest difficulties in forming, designated as complex shape products. The effect of the amount of recycled glass used in the preparation of glass batches on the conformation of products of complex shapes and on glass workability is discussed. The amount of recycled glass affects the volatilization of glass modifiers which in turn have an effect on the glass properties and workability. New glasses which become compatible with the use of oxygen burners were formulated, tested and developed to the industrial use, oxygen enrichment being used to reduce the mechanical and surface defects in pressed glass tableware. Compatibility glass / technology was achieved with a modified system of tuning of the glass. The modified glasses have physical and chemical properties similar to the original glass and therefore are commercially viable. The technology of the colouring channels was used to change glass workability of a glass base by the introduction of up to 5 % Li2O rich in colourless frit. The values of RMS (relative machine speed) fell from 106.8 % to 95.7 % while the values of Pt (cooling time) increased from 100.6 s to 111.3 s by the introduction of glass frits. The physico-chemical properties of the modified glass show commercial viability. This technology introduces flexibility in industrial processes of glass. The chemical composition of glass and therefore the properties related to workability can be understood as another variable of the glass forming processes and used according to the available forming techniques, the shape of objects and the engineering tools used for the moulds. Convergence was observed between experimental and predicted from Huff and Fluegel models in studying the properties of glasses. An important part of this work was done inside the industrial environment. On issues related to the investigation of the glass processing inside the industry, the practice of developing experimental work integrated in the industrial environment is clearly documented and referenced in the published literature in international journals and periodicals.

Calibration and validation of hydrodynamic, salt and heat transport models for Ria de Aveiro lagoon (Portugal)

Ria deAveiro is a very complex shallow water coastal lagoon located on the northwest of Portugal. Important issues would be left unanswered without a good understanding of hydrodynamic and transport processes occurring in the lagoon. Calibration and validation of hydrodynamic, salt and heat transport models for Ria de Aveiro lagoon are presented. The calibration of the hydrodynamic model was performed adjusting the bottom friction coefficient, through the comparison between measured and predicted time series of sea surface elevation for 22 stations. Harmonic analysis was performed in order to evaluate the model's accuracy. To validate the hydrodynamic model measured and predicted SSE values were compared for 11 stations, as well as main flow direction velocities for 10 stations. The salt and heat transport models were calibrated comparing measured and predicted time series of salinity and water temperature for 7 stations, and the RMS of the difference between the series was determined. These models were validated comparing the model results with an independent field data set. The hydrodynamic and the salt and heat transport models for Ria de Aveiro were successfully calibrated and validated. They reproduce accurately the barotropic flows and can therefore adequately represent the salt and heat transport and the heat transfer processes occurring in Ria deAveiro.

Estudo da maquinabilidade das ligas Ti-6Al-4V e Co-28Cr-6Mo na fresagem de dispositivos biomédicos

Os estudos de maquinabilidade de biomateriais e outros materiais aplicados na área médica são extensos. Todavia, muitos destes estudos recorrem a modelos de geometria regular e operações elementares de maquinagem. Relativamente a estas, os estudos académicos atualmente disponíveis mostram que a tecnologia preferencial é o torneamento, opção que se fundamenta na simplicidade de análise (corte ortogonal). Saliente-se ainda que, neste contexto, a liga de titânio Ti-6Al-4V constitui o biomaterial mais utilizado. Numa perspetiva complementar, refira-se que as publicações científicas evidenciam que a informação disponível sobre a fresagem Ti-6Al-4V não é muito extensa e a do Co-28Cr-6Mo é quase inexistente. A presente dissertação enquadra-se neste domínio e representa mais uma contribuição para o estudo da maquinabilidade das ligas de Titânio e de crómio-cobalto. A aplicação de operações de maquinagem complexas, através do recurso a programas informáticos de fabrico assistido por computador (CAM), em geometrias complexas, como é o caso das próteses femorais anatómicas, e o estudo comparativo da maquinabilidade das ligas Co-28Cr-6Mo e Ti-6Al-4V, constituem os objetivos fundamentais deste trabalho de doutoramento. Neste trabalho aborda-se a problemática da maquinabilidade das ligas metálicas usadas nos implantes ortopédicos, nomeadamente as ligas de titânio, de crómiocobalto e os aços Inoxidáveis. Efetua-se ainda um estudo da maquinagem de uma prótese femoral com uma forma geométrica complexa, onde as operações de corte foram geradas recorrendo às tecnologias de fabrico assistido por computador (CAD/CAM). Posteriormente, procedeu-se ao estudo da maquinabilidade das duas ligas usadas neste trabalho, dando uma atenção particular à determinação das forças de corte para diferentes velocidades de corte. Para além da monitorização da evolução da força de corte, o desgaste das ferramentas, a dureza e a rugosidade foram avaliadas, em função da velocidade de corte imposta. Por fim, com base nas estratégias de maquinagem adotadas, analisa-se a maquinabilidade e selecionam-se os parâmetros de corte mais favoráveis para as ligas de Titânio e Crómio-cobalto. Os resultados obtidos mostram que a liga de crómio-cobalto induz maior valor de força de corte do que a liga de titânio. Observa-se um aumento progressivo das forças de corte quando a velocidade de corte aumenta, até atingir o valor máximo para a velocidade de corte de 80m/min, após a qual, a força de corte tende a diminuir. Apesar do fabricante das ferramentas recomendar a velocidade de corte de 50 m/min para ambos os materiais, conclui-se que a velocidade de corte de 65 m/min induz o mesmo desgaste na ferramenta de corte no caso da liga de titânio, e menor desgaste no caso da liga de crómio-cobalto.

Feiras e exposições internacionais: um estudo exploratório dos fatores de decisão e motivação de participação numa feira internacional

Dissertação apresentada ao Instituto Superior de Contabilidade e Administração do Porto para obtenção do Grau de Mestre em Empreendedorismo e Internacionalização Orientada por Prof. Doutor José Freitas Santos

Flexibility in a Stackelberg leadership with differentiated goods

We study the effects of product differentiation in a Stackelberg model with demand uncertainty for the first mover. We do an ex-ante and ex-post analysis of the profits of the leader and of the follower firms in terms of product differentiation and of the demand uncertainty. We show that even with small uncertainty about the demand, the follower firm can achieve greater profits than the leader, if their products are sufficiently differentiated. We also compute the probability of the second firm having higher profit than the leading firm, subsequently showing the advantages and disadvantages of being either the leader or the follower firm.

Bertrand and Cournot oligopolies when rivals' costs are unknown

We study Bertrand and Cournot oligopoly models with incomplete information about rivals’ costs, where the uncertainty is given by a uniform distribution. We compute the Bayesian- Nash equilibrium of both games, the ex-ante expected profits and the ex-post profits of each firm. We see that, in the price competition, even though only one firm produces in equilibrium, all firms have a positive ex-ante expected profit.

Simultaneous decisions or leadership in an international competition

In this paper, we study an international market with demand uncertainty. The model has two stages. In the first stage, the home government chooses an import tariff to maximize the revenue. Then, the firms engage in a Cournot or in a Stackelberg competition. The uncertainty is resolved between the decisions made by the home government and by the firms. We compare the results obtained in the three different ways of moving on the decision make of the firms.