100 Gb/s uncooled DWDM using orthogonal coding for low-cost datacommunication links

We demonstrate a 10 x 10 Gb/s uncooled DWDM system using orthogonal coding on adjacent carriers, assuming the use of a monolithically integrated sources. A power saving of 72% is expected over traditional WDM. © 2014 OSA.

20 Gb/s mode-group-division multiplexing employing Hermite-Gaussian launches over worst-case multimode fiber links

For the first time, mode group division multiplexing is achieved in a multimode fiber link using a 2-D Hermite-Gaussian mode launch. 20 Gb/s error-free transmission is achieved over a 250 m worst-case OM1 multimode fiber link. © OSA 2014.

100 Gb/s PAM4-CAP2 real-time modulation of a single optical source for next-generation datacommunication links

100 Gb/s PAM4-CAP2 modulation is demonstrated for next-generation datacommunication links. Simulation studies indicate a power budget advantage of 2.5 dBo relative to PAM8 modulation. A real-time experimental demonstration is performed. © OSA 2014.

10 Gb/s transmitter-based equalization for extended-reach multimode-fiber datacommunication links

Transmitter-based equalization is investigated for enhanced performance in 10 Gb/s multimodefiber links. Rigorous simulations and proof-of-principle experiments over 500 m of FDDI-grade fiber confirm for the first time the potential superiority of the technique relative to receiver-based schemes. © 2007 Optical Society of America.

Study of high performance re-timing using a 40 Gb/s hybrid-integrated mach-zehnder all-optical regenerator

We experimentally show that a hybrid-integrated Mach-Zehnder switch with a high performance gate profile allows retiming of optical signals with an accuracy of 500-700fs even if the input timing jitter is increased to 3ps. © 2004 Optical Society of America.

10 Gb/s 光模块的设计与测试

Submitted by zhangdi (zhangdi@red.semi.ac.cn) on 2009-04-13T11:45:31Z

40 Gb/s 光电探测器小信号测试法和大信号测试系统研究

Submitted by 阎军 (yanj@red.semi.ac.cn) on 2010-06-21T07:30:12Z No. of bitstreams: 1 张邦宏--40 Gbs 光电探测器小信号测试法和大信号测试系统研究.pdf: 3057511 bytes, checksum: 0c2a4acd2c1687f6c3ee554b01030fed (MD5)

40-Gb/s Low Chirp Electroabsorption Modulator Integrated With DFB Laser

A 40-Gb/s monolithically integrated transmitter containing an InGaAsP multiple-quantum-well electroabsorption modulator (EAM) with lumped electrode and a distributed-feedback semiconductor laser is demonstrated. Superior characteristics are exhibited for the device, such as low threshold current of 20 mA, over 40-dB sidemode suppression ratio at 1550 nm, and more than 30-dB dc extinction ratio when coupled into a single-mode fiber. By adopting a deep ridge waveguide and planar electrode structures combined with buried benzocyclobutene, the capacitance of the EAM is reduced to 0.18 pF and the small-signal modulation bandwidth exceeds 33 GHz. Negative chirp operation is also realized when the bias voltage is beyond 1.6 V.

Monolithic integration of electroabsorption modulator and DFB laser for 10-Gb/s transmission

A strained InGaAsP-InP multiple-quantum-well DFB laser monolithically integrated with electroabsorption modulator by ultra-low-pressure (22 mbar) selective-area-growth is presented. The integrated chip exhibits superior characteristics, such as low threshold current of 19 mA, single-mode operation around 1550 nm range with side-mode suppression ratio over 40 dB, and larger than 16 dB extinction ratio when coupled into a single-mode fiber. More than 10 GHz modulation bandwidth is also achieved. After packaged in a compact module, the device successfully performs 10-Gb/s NRZ transmission experiments through 53.3 km of standard fiber with 8.7 dB dynamic extinction ratio. A receiver sensitivity of -18.9 dBm at bit-error-rate of 10(-1)0 is confirmed. (c) 2005 Elsevier B.V. All rights reserved.

Electroabsoorption-modulated laser light-source module using selective area growth for 10 Gb/s transmission

In this work, a novel light source of strained InGaAsP/InGaAsP MQW EAM monolithically integrated with DFB laser is fabricated by ultra-low-pressure (22 x 10(2) Pa) selective area growth ( SAG) MOCVD technique. Superior device performances have been obtained, sue h as low threshold current of 19 mA, output light power of about 7 mW, and over 16 dB extinction ratio at 5 V applied voltage when coupled into a single mode fiber. Over 10 GHz 3 dB bandwidth in EAM part is developed with a driving voltage of 3 V. After the chip is packaged into a 7-pin butterfly compact module, 10-Gb/s NRZ transmission experiments are successfully performed in standard fiber. A clearly-open eye diagram is achieved in the module output with over 8.3 dB dynamic extinction ratio. Power penalty less than 1.5 dB has been obtained after transmission through 53.3 km of standard fiber, which demonstrates that high-speed, low chirp EAM/DFB integrated light source can be obtained by ultra-low-pressure (22 x 102 Pa) SAG method.

Microwave packaging for 10 Gb/s EML modulators - art. no. 60201O

A novel microwave packaging technique for 10Gb/s electro-absorption modulator integrated with distributed feedback laser (EML) is presented. The packaging parasitics and intrinsic parasitics are both well considered, and the packaging circuit was synthetically designed to compensate for the intrinsic parasitic of the chip. A butterfly-packaged EMI module has been successfully developed to prove that. The small-signal modulation bandwidth of the butterfly-packaged module is about 10 GHz. Optical fiber transmission experiments have shown that the module can be used for 10Gb/s optical transmission system. After transmission through 40km,. the power penalty is less than 1 dBm at a bit-error-rate of 10-12.

A 10 Gb/s Directly-Modulated 1.3 mu m InAs/GaAs Quantum-Dot Laser

We demonstrate 10 Gb/s directly-modulated 1.3 mu m InAs quantum-dot (QD) lasers grown on GaAs substrates by molecular beam epitaxy. The active region of the QD lasers consists of five-stacked InAs QD layers. Ridge-waveguide lasers with a ridge width of 4 mu m and a cavity length of 600 mu m are fabricated with standard lithography and wet etching techniques. It is found that the lasers emit at 1293 nm with a very low threshold current of 5 mA at room temperature. Furthermore, clear eye-opening patterns under 10 Gb/s modulation rate at temperatures of up to 50 degrees C are achieved by the QD lasers. The results presented here have important implications for realizing low-cost, low-power-consumption, and high-speed light sources for next-generation communication systems.

1-Gb/s zero-pole cancellation CMOS transimpedance amplifier for Gigabit Ethernet applications

A zero-pole cancellation transimpedance amplifier (TIA) has been realized in 0.35 μm RF CMOS tech nology for Gigabit Ethernet applications. The TIA exploits a zero-pole cancellation configuration to isolate the input parasitic capacitance including photodiode capacitance from bandwidth deterioration. Simulation results show that the proposed TIA has a bandwidth of 1.9 GHz and a transimpedance gain of 65 dB·Ω for 1.5 pF photodiode capaci tance, with a gain-bandwidth product of 3.4 THz·Ω. Even with 2 pF photodiode capacitance, the bandwidth exhibits a decline of only 300 MHz, confirming the mechanism of the zero-pole cancellation configuration. The input resis tance is 50 Ω, and the average input noise current spectral density is 9.7 pA/(Hz)~(1/2). Testing results shows that the eye diagram at 1 Gb/s is wide open. The chip dissipates 17 mW under a single 3.3 V supply.

1.3-μm uncooled 10 Gb/s directly modulated MQW AlGaInAs/InP laser diodes

In this paper, we report a novel 1.3-μm uncooled AlGaInAs/InP multiple quantum well (MQW) ridge waveguide laser diodes. By optimizing the design of MQW structure and facet coatings, together with the application of reversed-mesa ridge waveguide (RM-RWG) structure, polyimide planarization, and lift-off processes technology, an uncooled 1.3-μm, 10-Gb/s directly modulated MQW ridge waveguide laser diode was successfully fabricated. The threshold current and the slope efficiency were 7 mA and 0.48 mW/mA, respectively. The directly modulated bandwidths of 11 and 9.2 GHz were achieved at room temperature and 80 Celsius degrees, respectively.

10 Gb／s电吸收调制器的微波封装设计

在高速光电子器件的微波封装过程中，需要综合考虑封装寄生参数和芯片寄生参数对器件高频性能的影响。利用封装寄生参数对芯片寄生参数的补偿作用，成功实现了10Gb／s电吸收调制激光器（EML）的高频封装。通过封装前后芯片和器件的小信号频率响应测试结果对比，器件的反射参数和传输参数有所改善，3dB带宽达到10GHz；并进行了10Gb／s速率的光纤传输实验，经过40km光纤传输后通道代价不到1dBm（误码率为10^-12），满足10Gb／s长距离光纤传输系统的要求。