Avaliação genética de touros da raça Gir para produção de leite no dia do controle e em 305 dias de lactação

Dados de 32.779 controles mensais, de 3.605 lactações em 305 dias (PL305), de 2.082 vacas Gir, filhas de 281 touros, com partos ocorridos de 1987 a 1999 em 11 rebanhos, foram usados com o objetivo de verificar a viabilidade de utilização da produção de leite no dia do controle (PLDC) em avaliações genéticas de touros da raça Gir. Foram realizadas análises univariadas das PLDC1 a PLDC10 e da PL305 pelo método de máxima verossimilhança restrita, sob modelo animal, incluindo as três primeiras lactações como medidas repetidas de um mesmo animal, diferenciados conforme o grupo contemporâneo de rebanho-ano-estação, de acordo com a idade da vaca ao parto e, do intervalo parto-primeiro controle na PLDC1. As médias observadas e os respectivos desvios-padrão (kg) para PLDC1 a PLDC10 e PL305 foram: 11,97±4,64; 11,93±4,68; 10,98±4,40; 10,18±4,12; 9,66±3,88; 9,20±3,69; 8,63±3,51; 8,08±3,33; 7,59±3,27; 7,22±3,15 e 2.746,17±1.299,90. As estimativas de herdabilidade para as PLDC1 a PLDC10 foram de 0,26; 0,19; 0,18; 0,20; 0,15; 0,13; 0,14; 0,10; 0,11 e 0,10, respectivamente; para a PL305 foi de 0,18. As correlações de ordem dos valores genéticos preditos de 281 touros, obtidos entre as PLDC e a PL305, foram altas, oscilando de 0,85 a 0,94. O percentual de coincidência de touros que seriam selecionados pelos valores genéticos preditos das PLDC2 a PLDC5 foram acima de 80%, a partir de 5% dos melhores classificados pela PL305. em algumas PLDC o nível de coincidência de classificação dos touros com a PL305 foi muito baixo.

Avaliação genética de caprinos da raça Alpina utilizando-se a produção de leite no dia do controle

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Controle on-line do número de não-conformidades por itens em uma produção finita

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Controle on-line por atributos para o número de não-conformidades no item inspecionado com base em uma sequência de inspeção

This paper proposes a procedure to control on-line processes for attributes, using an Shewhart control chart with two control limits (warning limit and control limit) and will be based on a sequence of inspection (h). The inspection procedure is based on Taguchi et al. (1989), in which to inspect the item, if the number of non-conformities is higher than an upper control limit, the process needs to be stopped and some adjustment is required; and, if the last inspection h, from all items inspected present a number of non-conformities between the control limit and warning limit. The items inspected will suffer destructive inspection, being discarded after inspection. Properties of an ergodic Markov chain are used to get the expression of average cost per item and the aim was the determination of four optimized parameters: the sampling interval of the inspections (m); the constant W to draw the warning limit (W); the constant C to draw the control limit (C), where W £ C, and the length of sequence of inspections (h). Numerical examples illustrate the proposed procedure

Controle preditivo não linear baseado no modelo de Hammerstein com prova de estabilidade

The Predictive Controller has been receiving plenty attention in the last decades, because the need to understand, to analyze, to predict and to control real systems has been quickly growing with the technological and industrial progress. The objective of this thesis is to present a contribution for the development and implementation of Nonlinear Predictive Controllers based on Hammerstein model, as well as to its make properties evaluation. In this case, in the Nonlinear Predictive Controller development the time-step linearization method is used and a compensation term is introduced in order to improve the controller performance. The main motivation of this thesis is the study and stability guarantee for the Nonlinear Predictive Controller based on Hammerstein model. In this case, was used the concepts of sections and Popov Theorem. Simulation results with literature models shows that the proposed approaches are able to control with good performance and to guarantee the systems stability

Uma arquitetura distribuída de hardware e software para controle de um robô móvel autônomo

In this work, we present a hardware-software architecture for controlling the autonomous mobile robot Kapeck. The hardware of the robot is composed of a set of sensors and actuators organized in a CAN bus. Two embedded computers and eigth microcontroller based boards are used in the system. One of the computers hosts the vision system, due to the significant processing needs of this kind of system. The other computer is used to coordinate and access the CAN bus and to accomplish the other activities of the robot. The microcontroller-based boards are used with the sensors and actuators. The robot has this distributed configuration in order to exhibit a good real-time behavior, where the response time and the temporal predictability of the system is important. We adopted the hybrid deliberative-reactive paradigm in the proposed architecture to conciliate the reactive behavior of the sensors-actuators net and the deliberative activities required to accomplish more complex tasks

Controle vetorial de velocidade de um motor de indução trifásico com estimação neural de fluxo

This work describes the study and the implementation of the speed control for a three-phase induction motor of 1,1 kW and 4 poles using the neural rotor flux estimation. The vector speed control operates together with the winding currents controller of the stator phasis. The neural flux estimation applied to the vector speed controls has the objective of compensating the parameter dependences of the conventional estimators in relation to the parameter machine s variations due to the temperature increases or due to the rotor magnetic saturation. The implemented control system allows a direct comparison between the respective responses of the speed controls to the machine oriented by the neural rotor flux estimator in relation to the conventional flux estimator. All the system control is executed by a program developed in the ANSI C language. The main DSP recources used by the system are, respectively, the Analog/Digital channels converters, the PWM outputs and the parallel and RS-232 serial interfaces, which are responsible, respectively, by the DSP programming and the data capture through the supervisory system

Controle de atitude e altitude para um veículo aéreo não tripulado do tipo quadrirrotor

A Quadrotor is an Unmanned Aerial Vehicle (UAV) equipped with four rotors distributed on a simple mechanical "X"form structure. The aim of this work is to build and stabilize a Quadrotor aircraft in the roll, pitch and yaw angles at a certain altitude. The stabilization control approach is based on a transformation in the input variables in order to perform a decoupled control. The proposed strategy is based on breaking the control problem into two hierarchical levels: A lower level, object of this work, maintains the desired altitude an angles of the vehicle while the higher level establishes appropriate references to the lower level, performing the desired movements. A hardware and software architecture was specially developed and implemented for an experimental prototype used to test and validate the proposed control approach

Uma fonte chaveada de 50kW com correção de fator de potência para alimentação de uma tocha de plasma Indutiva utilizando técnicas de controle digital

This work deals with the development of an experimental study on a power supply of high frequency that provides the toch plasmica to be implemented in PLASPETRO project, which consists of two static converters developed by using Insulated Gate Bipolar Transistor (IGBT). The drivers used to control these keys are triggered by Digital Signal Processor (DSP) through optical fibers to reduce problems with electromagnetic interference (EMI). The first stage consists of a pre-regulator in the form of an AC to DC converter with three-phase boost power factor correction which is the main theme of this work, while the second is the source of high frequency itself. A series-resonant inverter consists of four (4) cell inverters operating in a frequency around 115 kHz each one in soft switching mode, alternating itself to supply the load (plasma torch) an alternating current with a frequency of 450 kHz. The first stage has the function of providing the series-resonant inverter a DC voltage, with the value controlled from the power supply provided by the electrical system of the utility, and correct the power factor of the system as a whole. This level of DC bus voltage at the output of the first stage will be used to control the power transferred by the inverter to the load, and it may vary from 550 VDC to a maximum of 800 VDC. To control the voltage level of DC bus driver used a proportional integral (PI) controller and to achieve the unity power factor it was used two other proportional integral currents controllers. Computational simulations were performed to assist in sizing and forecasting performance. All the control and communications needed to stage supervisory were implemented on a DSP

Otimização do controle eletrônico do diagrama de radiação de arranjos de antenas usando algoritmos genéticos com codificação real

Antenna arrays are able to provide high and controlled directivity, which are suitable for radiobase stations, radar systems, and point-to-point or satellite links. The optimization of an array design is usually a hard task because of the non-linear characteristic of multiobjective, requiring the application of numerical techniques, such as genetic algorithms. Therefore, in order to optimize the electronic control of the antenna array radiation pattem through genetic algorithms in real codification, it was developed a numerical tool which is able to positioning the array major lobe, reducing the side lobe levels, canceling interference signals in specific directions of arrival, and improving the antenna radiation performance. This was accomplished by using antenna theory concepts and optimization methods, mainly genetic algorithms ones, allowing to develop a numerical tool with creative genes codification and crossover rules, which is one of the most important contribution of this work. The efficiency of the developed genetic algorithm tool is tested and validated in several antenna and propagation applications. 11 was observed that the numerical results attend the specific requirements, showing the developed tool ability and capacity to handle the considered problems, as well as a great perspective for application in future works.

Técnicas inteligentes hídridas para o controle de sistemas não lineares

A neuro-fuzzy system consists of two or more control techniques in only one structure. The main characteristic of this structure is joining one or more good aspects from each technique to make a hybrid controller. This controller can be based in Fuzzy systems, artificial Neural Networks, Genetics Algorithms or rein forced learning techniques. Neuro-fuzzy systems have been shown as a promising technique in industrial applications. Two models of neuro-fuzzy systems were developed, an ANFIS model and a NEFCON model. Both models were applied to control a ball and beam system and they had their results and needed changes commented. Choose of inputs to controllers and the algorithms used to learning, among other information about the hybrid systems, were commented. The results show the changes in structure after learning and the conditions to use each one controller based on theirs characteristics

Lógica Fuzzy para Controle de pH em um Processo Petrolífero

This work proposes the design, the performance evaluation and a methodology for tuning the initial MFs parameters of output of a function based Takagi-Sugeno-Kang Fuzzy-PI controller to neutralize the pH in a stirred-tank reactor. The controller is designed to perform pH neutralization of industrial plants, mainly in units found in oil refineries where it is strongly required to mitigate uncertainties and nonlinearities. In addition, it adjusts the changes in pH regulating process, avoiding or reducing the need for retuning to maintain the desired performance. Based on the Hammerstein model, the system emulates a real plant that fits the changes in pH neutralization process of avoiding or reducing the need to retune. The controller performance is evaluated by overshoots, stabilization times, indices Integral of the Absolute Error (IAE) and Integral of the Absolute Value of the Error-weighted Time (ITAE), and using a metric developed by that takes into account both the error information and the control signal. The Fuzzy-PI controller is compared with PI and gain schedule PI controllers previously used in the testing plant, whose results can be found in the literature.

Controle inteligente aplicado a uma mesa de coordenadas de dois graus de liberdade

This work presents the design and construction of an X-Y table of two degrees of freedom, as well as the development of a fuzzy system for its position and trajectory control. The table is composed of two bases that move perpendicularly to each other in the horizontal plane, and are driven by two DC motors. Base position is detected by position sensors attached to the motor axes. A data acquisition board performs the interface between a laptop and the plant. The fuzzy system algorithm was implemented in LabVIEW® programming environment that processes the sensors signals and determines the control variables values that drive the motors. Experimental results using position reference signals (step type signal) and straight and circular paths reference signals are presented to demonstrate the dynamic behavior of fuzzy system

Implementação de um sistema embarcado aplicado ao controle de pressão arterial

Hypertension is a dangerous disease that can cause serious harm to a patient health. In some situations the necessity to control this pressure is even greater, as in surgical procedures and post-surgical patients. To decrease the chances of a complication, it is necessary to reduce blood pressure as soon as possible. Continuous infusion of vasodilators drugs, such as sodium nitroprusside (SNP), rapidly decreased blood pressure in most patients, avoiding major problems. Maintaining the desired blood pressure requires constant monitoring of arterial blood pressure and frequently adjusting the drug infusion rate. Manual control of arterial blood pressure by clinical personnel is very demanding, time consuming and, as a result, sometimes of poor quality. Thus, the aim of this work is the design and implementation of a database of tuned controllers based on patients models, in order to find a suitable PID to be embedded in a Programmable Integrated Circuit (PIC), which has a smaller cost, smaller size and lower power consumption. For best results in controlling the blood pressure and choosing the adequate controller, tuning algorithms, system identification techniques and Smith predictor are used. This work also introduces a monitoring system to assist in detecting anomalies and optimize the process of patient care.

Enxertia em plantas de pimentão no controle da murcha de fitóftora em ambiente protegido

Avaliou-se a viabilidade de utilização da enxertia em plantas de pimentão (Capsicum annuum, L.), visando o controle da murcha de fitóftora. A pesquisa foi conduzida de setembro de 2000 a julho de 2001, na UNESP, Botucatu, em ambiente protegido. Adotou-se o delineamento experimental de blocos ao acaso, com 4 repetições e 5 plantas por parcela. Foram utilizados dois porta-enxertos resistentes a Phytophthora capsici, híbridos F1 de Capsicum annuum, e três híbridos comerciais suscetíveis (Elisa, Margarita e Magali-R). A enxertia foi realizada quando porta-enxertos e enxertos apresentavam respectivamente sete e três folhas verdadeiras, pelo método de garfagem fenda simples. Aos 14 dias após o transplante das mudas foi feita a inoculação do fungo, utilizando sementes de trigo infestadas pelo patógeno, depositadas ao redor do colo da planta. Quatro dias após a inoculação, e a partir daí a cada 15 dias, foram feitas avaliações que confirmaram a resistência dos porta-enxertos e a suscetibilidade das plantas não enxertadas. Observou-se bom nível de compatibilidade de enxertia em todas as combinações, precocidade de florescimento das plantas não enxertadas, manutenção de resistência à doença pelas plantas enxertadas durante todo o período e variações na altura das plantas em algumas combinações. Com relação à produção, verificou-se que os frutos mantiveram as características fenotípicas de cada híbrido, revelando que não houve interferência dos porta-enxertos neste aspecto. Concluiu-se haver viabilidade técnica de utilização da enxertia no controle da murcha de fitóftora em ambiente protegido.