Resposta térmica de um compósito PEEK+PTFE+Fibra de carbono+grafite

Composites based on PEEK + PTFE + CARBON FIBER + Graphite (G_CFRP) has increased application in the top industries, as Aerospace, Aeronautical, Petroleum, Biomedical, Mechanical and Electronics Engineering challenges. A commercially available G_CFRP was warmed up to three different levels of thermal energy to identify the main damage mechanisms and some evidences for their intrinsic transitions. An experimental test rig for systematize a heat flux was developed in this dissertation, based on the Joule Effect. It was built using an isothermal container, an internal heat source and a real-time measurement system for test a sample by time. A standard conical-cylindrical tip was inserted into a soldering iron, commercially available and identified by three different levels of nominal electrical power, 40W (manufacturer A), 40W (manufacturer B), 100W and 150W, selected after screening tests: these power levels for the heat source, after one hour of heating and one hour of cooling in situ, carried out three different zones of degradation in the composite surface. The bench was instrumented with twelve thermocouples, a wattmeter and a video camera. The twelve specimens tested suffered different degradation mechanisms, analyzed by DSC (Differential Scanning Calorimetry) and TG (Thermogravimetry) techniques, Scanning Electron Microscopy (SEM) and Energy-Dispersive X-Rays (EDX) Analysis. Before and after each testing, it was measured the hardness of the sample by HRM (Hardness Rockwell M). Excellent correlations (R2=1) were obtained in the plots of the evaporated area after one hour of heating and one hour of cooling in situ versus (1) the respective power of heat source and (2) the central temperature of the sample. However, as resulting of the differential degradation of G_CFRP and their anisotropy, confirmed by their variable thermal properties, viscoelastic and plastic properties, there were both linear and non-linear behaviour between the temperature field and Rockwell M hardness measured in the radial and circumferential directions of the samples. Some morphological features of the damaged zones are presented and discussed, as, for example, the crazing and skeletonization mechanism of G_CFRP

Genotoxicidade e composição do material particulado emitido pela queima de Biomassa: um estudo de caso em Tangará da Serra, Região da Amazônia Brasileira

Tangara da Serra is located on southwestern Mato Grosso and is found to be on the route of pollutants dispersion originated in the Legal Amazon s deforestation area. This region has also a wide area of sugarcane culture, setting this site quite exposed to atmospheric pollutants. The objective of this work was to evaluate the genotoxicity of three different concentrations of organic particulate matter which was collected from August through December / 2008 in Tangara da Serra, using micronucleus test in Tradescantia pallida (Trad-MCN). The levels of particulate matter less than 10μm (MP10) and black carbon (BC) collected on the Teflon and polycarbonate filters were determined as well. Also, the alkanes and polycyclic aromatic hydrocarbons (PAHs) were identified and quantified on the samples from the burning period by gas chromatography detector with flame ionization detection (GC-FID). The results from the analyzing of alkanes indicate an antropic influence. Among the PAHs, the retene was the one found on the higher quantity and it is an indicator of biomass burning. The compounds indene(1,2,3-cd)pyrene and benzo(k)fluoranthene were identified on the samples and are considered to be potentially mutagenic and carcinogenic. By using Trad-MCN, it was observed a significant increase on the micronucleus frequency during the burning period, and this fact can be related to the mutagenic PAHs which were found on such extracts. When the period of less burnings is analyzed and compared to the negative control group, it was noted that there was no significant difference on the micronuclei rate. On the other hand, when the higher burning period is analyzed, statistically significant differences were evident. This study showed that the Trad-MCN was sensible and efficient on evaluating the genotoxicity potencial of organic matter from biomass burning, and also, emphasizes the importance of performing a chemical composition analysis in order to achieve a complete diagnosis on environmental risk control

Preparação e caracterização de catalisadores à base de titânio suportado em MCM-41 para produção de compostos oxigenados através da pirólise catalítica do capim elefante

In recent years, the area of advanced materials has been considerably, especially when it comes to materials for industrial use, such as is the case with structured porosity of catalysts suitable for catalytic processes. The use of catalysts combined with the fast pyrolysis process is an alternative to the oxygenate production of high added value, because, in addition to increasing the yield and quality of products, allows you to manipulate the selectivity to a product of interest, and therefore allows greater control over the characteristics of the final product. Based on these arguments, in this work were prepared titanium catalysts supported on MCM-41 for use in catalytic pyrolysis of biomass, called elephant grass. The reactions of pyrolysis of biomass were performed in a micro pyrolyzer, Py-5200, coupled to GC / MS, the company CDS Corporation, headquartered in the United States. The catalysts Ti-MCM-41 in different molar ratios were characterized by XRD, TG / DTG, FT-IR, SEM, XRF, UV-visible adsorption of nitrogen and the distribution of particle diameter and specific surface area measurement by the BET method. From the catalytic tests it was observed that the catalysts synthesized showed good results for the pyrolysis reaction.The main products were obtained a higher yield of aldehydes, ketones and furan. It was observed that the best reactivity is a direct function of the ratio Si/Ti, nature and concentration of the active species on mesoporous supports. Among the catalysts Ti-MCM-41 (molar ratio Si / Ti = 25 and 50), the ratio Si / Ti = 25 (400 ° C and 600 ° C) favored the cracking of oxygenates such as acids , aldehydes, ketones, furans and esters. Already the sample ratio Si / Ti = 50 had the highest yield of aromatic oxygenates

Sistemas de medição de desempenho para projetos de PD&I no Setor de Petróleo e Gás Natural

Organizations are seeking new ideas, tools and methods aiming to improve management process and performance. On the other hand, system performance measurement needs to portray organizational changes and provide managers with a set of true and more appropriate information for the decision-making process. This work aims to propose a performance measurement system in the academic field regarding Research, Development and Innovation (RDI) in the oil and gas industry. The research performed a bibliographic review in a descriptive exploratory manner. A field research was conducted with an expert focus group in order to gather new indicators. As for the validation of these indicators, a survey with experienced professional was also realized. The research surveyed four segments in and outside of the Federal University of Rio Grande do Norte-Brazil such as oil and gas project coordinators, staff at Academic Planning Offices, FUNPEC employees as well as coordinators from Petrobrás. The performance measuring system created from this study features three interrelated performance indicators pointed out as: process indicators, outcome indicators and global indicators. The proposal includes performance indicators that seek to establish more appropriate strategies for effective institution management. It might help policy making of university-industry interaction policies

A dinâmica do pensamento geométrico :aprendendo a enxergar meias verdades e a construir novos significados

This work is a case study to investigate the dynamics of the historians thought as they produce a knowledge about the history of the area measurement systems as forms of historical expressions and representations. We refer to some of the ideas of David Bohm (1989, 1992, 1994, 1996) to support our theoretical understanding about the operation of thought. We chose a period that is recognized by the theorists as the origin of the geometrical thought -embracing the knowledge developed by the Egyptians, Babylonians, Chinese, Hindus, Greeks and Romans- and is referred to as containing a cycle in the development of this knowledge, described as beginning, apogee and decline. We assume this history, as told by the theorists, as a version that we organize and tell with the help of three sets of categories. The first refers to the elements that take part in the measurement practices; the second refers to the historians understanding about the development of the scientific knowledge. This exercise allowed us to extract the theorists main beliefs, that we criticized in the light of the knowledge about Cubação (Dal Pian, 1990). We stress the importance of the methodological approach adopted in this study to the teaching of Geometry and its history

Fatores da satisfação e fidelidade de clientes na hotelaria: um estudo sobre a percepção dos gestores de hotéis

This Master of Science Thesis deals with the perception of hotels managers about the factors affecting the loyalty and satisfaction of its customers. It is surveyed a group of managers attending a hotel industry meeting and the results of their responses are compared with three surveys on tourist satisfaction and loyalty factors in Natal, Brazil, including international, national and regional tourist. The main findings suggest a divergence on the managers perception and the customer significant factors affecting satisfaction surveyed, but a certain convergence on the factors affecting loyalty. The research suggest a need for a customer satisfaction and loyalty measurement system in order to contribute for the alignment of managers perception and its customers evaluations

Um sistema para estimação da vazão de gás de poços produzindo por Plunger Lift para vaso separador de teste em plataformas de petróleo

This work intends to analyze the behavior of the gas flow of plunger lift wells producing to well testing separators in offshore production platforms to aim a technical procedure to estimate the gas flow during the slug production period. The motivation for this work appeared from the expectation of some wells equipped with plunger lift method by PETROBRAS in Ubarana sea field located at Rio Grande do Norte State coast where the produced fluids measurement is made in well testing separators at the platform. The oil artificial lift method called plunger lift is used when the available energy of the reservoir is not high enough to overcome all the necessary load losses to lift the oil from the bottom of the well to the surface continuously. This method consists, basically, in one free piston acting as a mechanical interface between the formation gas and the produced liquids, greatly increasing the well s lifting efficiency. A pneumatic control valve is mounted at the flow line to control the cycles. When this valve opens, the plunger starts to move from the bottom to the surface of the well lifting all the oil and gas that are above it until to reach the well test separator where the fluids are measured. The well test separator is used to measure all the volumes produced by the well during a certain period of time called production test. In most cases, the separators are designed to measure stabilized flow, in other words, reasonably constant flow by the use of level and pressure electronic controllers (PLC) and by assumption of a steady pressure inside the separator. With plunger lift wells the liquid and gas flow at the surface are cyclical and unstable what causes the appearance of slugs inside the separator, mainly in the gas phase, because introduce significant errors in the measurement system (e.g.: overrange error). The flow gas analysis proposed in this work is based on two mathematical models used together: i) a plunger lift well model proposed by Baruzzi [1] with later modifications made by Bolonhini [2] to built a plunger lift simulator; ii) a two-phase separator model (gas + liquid) based from a three-phase separator model (gas + oil + water) proposed by Nunes [3]. Based on the models above and with field data collected from the well test separator of PUB-02 platform (Ubarana sea field) it was possible to demonstrate that the output gas flow of the separator can be estimate, with a reasonable precision, from the control signal of the Pressure Control Valve (PCV). Several models of the System Identification Toolbox from MATLAB® were analyzed to evaluate which one better fit to the data collected from the field. For validation of the models, it was used the AIC criterion, as well as a variant of the cross validation criterion. The ARX model performance was the best one to fit to the data and, this way, we decided to evaluate a recursive algorithm (RARX) also with real time data. The results were quite promising that indicating the viability to estimate the output gas flow rate from a plunger lift well producing to a well test separator, with the built-in information of the control signal to the PCV

Análise teórica e experimental de superfícies seletivas de freqüência e suas aplicações em antenas planares

This work presents a theoretical and numerical analysis of structures using frequency selective surfaces applied on patch antennas. The FDTD method is used to determine the time domain reflected fields. Applications of frequency selective surfaces and patch antennas cover a wide area of telecommunications, especially mobile communications, filters and WB antennas. scattering parameters are obteained from Fourier Transformer of transmited and reflected fields in time domain. The PML are used as absorbing boundary condition, allowing the determination of the fields with a small interference of reflections from discretized limit space. Rectangular patches are considered on dielectric layer and fed by microstrip line. Frequency selective surfaces with periodic and quasi-periodic structures are analyzed on both sides of antenna. A literature review of the use of frequency selective surfaces in patch antennas are also performed. Numerical results are also compared with measured results for return loss of analyzed structures. It is also presented suggestions of continuity to this work

Uma metodologia para redução de incertezas em sistema de medição de vazão de óleo e gás

The objective of this research is to discuss about the need for implementation of new alternatives for the implementation on the metrological control: on the findings of initial and subsequent measurements, the control procedures of measurement uncertainty applied in assessing the loss or remains found in handling operations of bulk liquids, when used turbine meters used in measuring the tax on the business of Petrobras, due to the current environment of legal metrology and scientific, both domestic and international. We aim, with these alternatives: standardizing the minimization of random and systematic errors, the estimate of the remaining errors, as well as the management control of metrological calibration procedures, control of measurement uncertainty, and contribute to the change in the form of performance of legal metrology and scientific disseminating new information to change management of metrological control, objectively focused on aspects of supervision in implementing these activities in the control of the uncertainties of measurement used in our processes in the fiscal measurement system Petrobras. Results are presented, information and comments on the influence of measurement uncertainty in the current results of the fiscal and transfer of custody. This will emphasize the need, among other things, improvement and expansion of metrological control monitored by setting a better meet demand, calibration equipment and measuring instruments for Petrobras. Finally, we intend to establish the need for improving the method of evaluation of the data meter applied to the current management control of measurement uncertainty by proposing a methodology for addressing the problem, as well as highlighting the expected results.

Desenvolvimento e avaliação de padrão de torque para calibração de torquímetros em três faixas de medição

The continuous development of instruments and equipment used as tools or torque measurement in the industry is demanding more accurate techniques in the use of this kind instrumentation, including development of metrological characteristics in torque measurement. The same happens with the needs in calibration services. There is a diversity of methods of hand torque tools in the market with different measuring range but without complaining with technical standards in terms of requirements of quality and reliability. However, actually there is no choice of a torque measuring standard that fulfils, with low cost, the needs for the calibration of hand torque tools in a large number of ranges. The objective of this thesis is to show the development and evaluation of a torque measuring standard device with a conception to allow the calibration of hand torque tools with three levels of torque with an single instrument, promoting reduction of costs and time in the calibration, also offering reliability for the evaluation of torque measuring instrument. To attend the demand in the calibration of hand torque tools it is necessary that the calibration laboratories have a big collection of torque measuring standards, to fulfills the needs of the costumer, what is very costly. The development of this type of torque measuring standard revealed a viable technique and economically making possible the calibration of hand torque tools in different nominal ranges through a single measurement system versatile, efficient and of easy operation

Síntese e caracterização de componentes nanoestruturados de células a combustível de óxidos sólidos

Perovskite-like ceramic materials present the general formula ABO3, where A is a rare earth element or an alkaline metal element, and B is a transition metal. These materials are strong candidates to assume the position of cathode in Solid Oxide Fuel Cells (SOFC), because they present thermal stability at elevated temperatures and interesting chemical and physical properties, such as superconductivity, dieletricity, magnetic resistivity, piezoelectricity, catalytic activity and electrocatalytic and optical properties. In this work the cathodes of Solid Oxide Fuel Cells with the perovskite structure of La1-xSrxMnO3 (x = 0.15, 0.22, 0.30) and the electrolyte composed of zirconia-stabilized-yttria were synthesized by the Pechini method. The obtained resins were thermal treatment at 300 ºC for 2h and the obtained precursors were characterized by thermal analysis by DTA and TG / DTG. The powder precursors were calcined at temperatures from 450 to 1350ºC and were analyzed using XRD, FTIR, laser granulometry, XRF, surface area measurement by BET and SEM methods. The pellets were sintered from the powder to the study of bulk density and thermal expansion

Genotoxicidade e composição do material particulado emitido pela queima de Biomassa: um estudo de caso em Tangará da Serra, Região da Amazônia Brasileira

Tangara da Serra is located on southwestern Mato Grosso and is found to be on the route of pollutants dispersion originated in the Legal Amazon s deforestation area. This region has also a wide area of sugarcane culture, setting this site quite exposed to atmospheric pollutants. The objective of this work was to evaluate the genotoxicity of three different concentrations of organic particulate matter which was collected from August through December / 2008 in Tangara da Serra, using micronucleus test in Tradescantia pallida (Trad-MCN). The levels of particulate matter less than 10μm (MP10) and black carbon (BC) collected on the Teflon and polycarbonate filters were determined as well. Also, the alkanes and polycyclic aromatic hydrocarbons (PAHs) were identified and quantified on the samples from the burning period by gas chromatography detector with flame ionization detection (GC-FID). The results from the analyzing of alkanes indicate an antropic influence. Among the PAHs, the retene was the one found on the higher quantity and it is an indicator of biomass burning. The compounds indene(1,2,3-cd)pyrene and benzo(k)fluoranthene were identified on the samples and are considered to be potentially mutagenic and carcinogenic. By using Trad-MCN, it was observed a significant increase on the micronucleus frequency during the burning period, and this fact can be related to the mutagenic PAHs which were found on such extracts. When the period of less burnings is analyzed and compared to the negative control group, it was noted that there was no significant difference on the micronuclei rate. On the other hand, when the higher burning period is analyzed, statistically significant differences were evident. This study showed that the Trad-MCN was sensible and efficient on evaluating the genotoxicity potencial of organic matter from biomass burning, and also, emphasizes the importance of performing a chemical composition analysis in order to achieve a complete diagnosis on environmental risk control

Preparação e caracterização de catalisadores à base de titânio suportado em MCM-41 para produção de compostos oxigenados através da pirólise catalítica do capim elefante

In recent years, the area of advanced materials has been considerably, especially when it comes to materials for industrial use, such as is the case with structured porosity of catalysts suitable for catalytic processes. The use of catalysts combined with the fast pyrolysis process is an alternative to the oxygenate production of high added value, because, in addition to increasing the yield and quality of products, allows you to manipulate the selectivity to a product of interest, and therefore allows greater control over the characteristics of the final product. Based on these arguments, in this work were prepared titanium catalysts supported on MCM-41 for use in catalytic pyrolysis of biomass, called elephant grass. The reactions of pyrolysis of biomass were performed in a micro pyrolyzer, Py-5200, coupled to GC / MS, the company CDS Corporation, headquartered in the United States. The catalysts Ti-MCM-41 in different molar ratios were characterized by XRD, TG / DTG, FT-IR, SEM, XRF, UV-visible adsorption of nitrogen and the distribution of particle diameter and specific surface area measurement by the BET method. From the catalytic tests it was observed that the catalysts synthesized showed good results for the pyrolysis reaction.The main products were obtained a higher yield of aldehydes, ketones and furan. It was observed that the best reactivity is a direct function of the ratio Si/Ti, nature and concentration of the active species on mesoporous supports. Among the catalysts Ti-MCM-41 (molar ratio Si / Ti = 25 and 50), the ratio Si / Ti = 25 (400 ° C and 600 ° C) favored the cracking of oxygenates such as acids , aldehydes, ketones, furans and esters. Already the sample ratio Si / Ti = 50 had the highest yield of aromatic oxygenates

Sistemas de medição de desempenho para projetos de PD&I no Setor de Petróleo e Gás Natural

Organizations are seeking new ideas, tools and methods aiming to improve management process and performance. On the other hand, system performance measurement needs to portray organizational changes and provide managers with a set of true and more appropriate information for the decision-making process. This work aims to propose a performance measurement system in the academic field regarding Research, Development and Innovation (RDI) in the oil and gas industry. The research performed a bibliographic review in a descriptive exploratory manner. A field research was conducted with an expert focus group in order to gather new indicators. As for the validation of these indicators, a survey with experienced professional was also realized. The research surveyed four segments in and outside of the Federal University of Rio Grande do Norte-Brazil such as oil and gas project coordinators, staff at Academic Planning Offices, FUNPEC employees as well as coordinators from Petrobrás. The performance measuring system created from this study features three interrelated performance indicators pointed out as: process indicators, outcome indicators and global indicators. The proposal includes performance indicators that seek to establish more appropriate strategies for effective institution management. It might help policy making of university-industry interaction policies

Projeto de intervenção adaptando o Balanced Scorecard ao sistema de compras da Base Aérea de Natal

The present proposal for intervention examines the issue of public procurements carried out by a military organization on a Federal Public Administration. The main objective of this paper is to propose a model of strategic planning based on the Balanced Scorecard for the public procurement system, which contributes to increased efficiency, efficacy and effectiveness of acquisitions made in the Air Base of Natal city. Therefore, Structured interviews were used in order to make a diagnosis of the current reality of the procurement system along with the main requirement sectors of BANT, as well as the adaptation of the prospects of the BSC based on literature review. The technique used for the analysis of the interviews was the analysis of content whose results contributed to the preparation of the conceptual Strategic Map which was submitted to validation through a Focal Group. It was concluded through the analysis of the interviews, that the system of purchases of BANT is in a tactical profile because of low interaction between the system of purchases and the requirement sectors, aiming only at the “economicity” of acquisition in opposition of the effectiveness of material acquired, the lack of training of the elements which build the system and the absence of a proper planning. It is intended with thecreation of this proposal to contribute to the improvement of management with a focus on results in public administration as well as increasing efficiency, efficacy and effectiveness of public procurements. Whereas for the particular case the measurement of the results can only be performed after at least a year of its implementation, the present research constitutes a proposal of intervention.