Desempenho térmico de coberturas: Um estudo comparativo entre as telhas de material reciclado, de fibra e betume, fibrocimento e cerâmica

This study aims to compare the thermal performance of tiles made from recycled material (waste packaging cardboard with aluminized film) with the tiles of fiber and bitumen, fiber cement and red ceramic with the aim of verifying the suitability of tile to be used in hot and humid climate of low latitude. The samples were selected according to the availability from Natal - RN market, as they are sold to the consumers. The methodology was based on studies that used experimental apparatus composed of thermal chambers heated by banks of incandescent bulbs, to analyze the thermal performance of materials. The tiles in the study were submitted to analysis of thermal performance, thermophysical properties and absorptance, using chambers of thermal performance, measuring the thermophysical properties and portable spectrometer, respectively. Comparative analysis of thermal performance between two samples of the recycled material with dimple sizes and different amounts of aluminum were made, in order to verify, if these characteristics had some interference on the thermal performance of them; the results showed no significant performance differences between the samples. The data obtained in chambers of thermal performance and confirmed by statistical analysis, showed, that the tile of recycled material have similar thermal performance to the tile of fiber cement. In addition to these tests was carried out the automatic monitoring of a building covered with tiles of recycled material, to verify its thermal performance in a real situation. The results showed that recycled shingles must be used with technical criteria similar to those used for fiber cement tiles, with regard to the heat gain into the building. Within these criteria should be taken into account local characteristics, especially in regions with hot and humid climate, and its use must be associated, according to the literature, to elements of thermal insulation and use of passive techniques such as vented attics, ceilings and right foot higher

Otimização e análise mecânica de pastas geopoliméricas para uso em poços sujeitos à injeção cíclica de vapor

Oil wells subjected to cyclic steam injection present important challenges for the development of well cementing systems, mainly due to tensile stresses caused by thermal gradients during its useful life. Cement sheath failures in wells using conventional high compressive strength systems lead to the use of cement systems that are more flexible and/or ductile, with emphasis on Portland cement systems with latex addition. Recent research efforts have presented geopolymeric systems as alternatives. These cementing systems are based on alkaline activation of amorphous aluminosilicates such as metakaolin or fly ash and display advantageous properties such as high compressive strength, fast setting and thermal stability. Basic geopolymeric formulations can be found in the literature, which meet basic oil industry specifications such as rheology, compressive strength and thickening time. In this work, new geopolymeric formulations were developed, based on metakaolin, potassium silicate, potassium hydroxide, silica fume and mineral fiber, using the state of the art in chemical composition, mixture modeling and additivation to optimize the most relevant properties for oil well cementing. Starting from molar ratios considered ideal in the literature (SiO2/Al2O3 = 3.8 e K2O/Al2O3 = 1.0), a study of dry mixtures was performed,based on the compressive packing model, resulting in an optimal volume of 6% for the added solid material. This material (silica fume and mineral fiber) works both as an additional silica source (in the case of silica fume) and as mechanical reinforcement, especially in the case of mineral fiber, which incremented the tensile strength. The first triaxial mechanical study of this class of materials was performed. For comparison, a mechanical study of conventional latex-based cementing systems was also carried out. Regardless of differences in the failure mode (brittle for geopolymers, ductile for latex-based systems), the superior uniaxial compressive strength (37 MPa for the geopolymeric slurry P5 versus 18 MPa for the conventional slurry P2), similar triaxial behavior (friction angle 21° for P5 and P2) and lower stifness (in the elastic region 5.1 GPa for P5 versus 6.8 GPa for P2) of the geopolymeric systems allowed them to withstand a similar amount of mechanical energy (155 kJ/m3 for P5 versus 208 kJ/m3 for P2), noting that geopolymers work in the elastic regime, without the microcracking present in the case of latex-based systems. Therefore, the geopolymers studied on this work must be designed for application in the elastic region to avoid brittle failure. Finally, the tensile strength of geopolymers is originally poor (1.3 MPa for the geopolymeric slurry P3) due to its brittle structure. However, after additivation with mineral fiber, the tensile strength became equivalent to that of latex-based systems (2.3 MPa for P5 and 2.1 MPa for P2). The technical viability of conventional and proposed formulations was evaluated for the whole well life, including stresses due to cyclic steam injection. This analysis was performed using finite element-based simulation software. It was verified that conventional slurries are viable up to 204ºF (400ºC) and geopolymeric slurries are viable above 500ºF (260ºC)

Degradação do PMMA através da reação despolimerização uitlizando catalisadores de óxidos mistos

In this work, mixed oxides were synthesized by two methods: polymeric precursor and gel-combustion. The oxides, Niquelate of Lanthanum, Cobaltate of Lanthanum and Cuprate of Lanthanum were synthesized by the polymeric precursor method, and treated at 300 º C for 2 hours, calcined at 800 º C for 6h in air atmosphere. In gel-combustion method were produced and oxides using urea and citric acid as fuel, forming for each fuel the following oxides Ferrate of Lanthanum, Cobaltato of Lanthanum and Ferrato of Cobalt and Lanthanum, which were submitted to the combustion process assisted by microwave power maximum of 10min. The samples were characterized by: thermogravimetric analysis, X-ray diffraction; fisisorção of N2 (BET method) and scanning electron microscopy. The reactions catalytic of depolymerization of poly (methyl methacrylate), were performed in a reactor of silica, with catalytic and heating system equipped with a data acquisition system and the gas chromatograph. For the catalysts synthesized using the polymeric precursor method, the cuprate of lanthanum was best for the depolymerization of the recycled polymer, obtaining 100% conversion in less time 554 (min), and the pure polymer, was the Niquelate of Lanthanum, with 100% conversion in less time 314 (min). By gel-combustion method using urea as fuel which was the best result obtained Ferrate of Lanthanum for the pure polymer with 100% conversion in less time 657 (min), and the recycled polymer was Cobaltate of Lanthanum with 100 % conversion in less time 779 (min). And using citric acid to obtain the best result for the pure polymer, was Ferrate of Lanthanum with 100% conversion in less time 821 (min and) for the recycled polymer, was Ferrate of Lanthanum with 98.28% conversion in less time 635 (min)

Estudo morfológico da blenda polimérica poli(metacrilato de metila)/poli(tereftalato de etileno) reciclado (PMMA/PET)

Among the options for plastics modification more convenient, both from a technical-scientific and economic, is the development of polymer blends by processing in the molten state. This work was divide into two stages, with the aim to study the phase morphology of binary blend PMMA / PET blend and this compatibilized by the addition of the poly(methyl methacrylate-co-glycidyl methacrylate-co-ethyl acrylate) copolymer (MMA-GMA-EA). In the first stage is analyzed the morphology of the blend at a preliminary stage where we used the bottle-grade PET in a Haake torque rheometer and the effect of compatibilizer in this blend was evaluated. In the second stage the blend was processed using the recycled PET in a single screw extruder and subsequently injection molding in the shape of specimens for mechanical tests. In both stages we used a transmission electron microscopy (TEM) to observe the morphologies of the samples and an image analyzer to characterize them. In the second stage, as well as analysis by TEM, tensile test, scanning electron microscopy (SEM) and atomic force microscopy (AFM) was performed to correlate the morphology with the mechanical properties. The samples used in morphological analyzes were sliced by cryo-ultramicrotomy technique for the analysis by TEM and the analysis by SEM and AFM, we used the flat face of the block after cut cryogenic. It was found that the size of the dispersed phase decreased with the addition of MMA-GMA-EA in blends prepared in a Haake. In the tensile test, the values of maximum tensile strength and modulus of elasticity is maintained in a range between the value of pure PMMA the pure PET, while the elongation at break was influenced by the composition by weight of the PMMA mixture. The coupling agent corroborated the results presented in the blend PMMA / PETrec / MMA-GMA-EA (80/15/5 %w/w), obtained by TEM, AFM and SEM. It was concluded that the techniques used had a good morphologic correlation, and can be confirmed for final analysis of the morphological characteristics of the blends PMMA / PET

O efeito do tratamento da atapulgita no desenvolvimento de compósito com o polietileno reciclado

The study aimed at the treatment of attapulgite for the development and characterization of composite recycled low density polyethylene - PEBD_rec embedded with natural attapulgite - ATP_NAT, sifted - ATP_PN and attapulgite treated with sulfuric acid - ATP_TR in different compositions (1, 3 and 5%) and compared with the PEBD_rec. The atapulgitas, natural, screened and treated, were characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), particle size analysis, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and determining the area specific surface (BET). The composites were characterized by thermogravimetry (TG), differential scanning calorimetry (DSC), Xray diffraction (XRD), torque rheometry, scanning electron microscopy (SEM) and traction. The composite PEBD_rec / ATP (natural, sieved and treated) were produced by mixing in the molten state in a single screw extruder matrix wire with subsequent reprocessing matrix tape. It was found that the screening of attapulgite not reduce the quantity of quartz and the acid treatment completely extracted dolomite aggregate impurities of the channels attapulgite, and increase their surface area. The addition of attapulgite in PEBD_rec acts as a catalyst, reducing the thermal stability of the polymer. The increased concentration of attapulgite, increases resistance and reduces the elongation at break and modulus of elasticity of the composite PEBD_rec / attapulgite

Desenvolvimento e caracterização de compósitos poli(tereftalato de etileno) reciclado (PET reciclado) com flocos de vidro.

The growing concern with the solid residues management, observed in the last decade, due to its huge amount and impact, has motivated the search for recycling processes, where these residues can be reprocessed to generate new products, enlarging the cycle of materials and energy which are present. Among the polymeric residues, there is poly (ethylene terephthalate) (PET). PET is used in food packaging, preferably in the bottling of carbonated beverages. The reintegration of post-consumer PET in half can be considered a productive action mitigation of environmental impacts caused by these wastes and it is done through the preparation of several different products at the origin, i.e. food packaging, with recycling rates increasing to each year. This work focused on the development and characterization mechanical, thermal, thermo-mechanical, dynamic mechanical thermal and morphology of the pure recycled PET and recycled PET composites with glass flakes in the weight fraction of 5%, 10% and 20% processed in a single screw extruder, using the following analytical techniques: thermogravimetry (TG), differential scanning calorimetry (DSC), tensile, Izod impact, Rockwell hardness, Vicat softening temperature, melt flow rate, burn rate, dynamic mechanical thermal analysis (DMTA) and scanning electron microscopy (SEM). The results of thermal analysis and mechanical properties leading to a positive evaluation, because in the thermograms the addition of glass flakes showed increasing behavior in the initial temperatures of thermal decomposition and melting crystalline, Furthermore was observed growing behavior in the mechanical performance of polymer composites, whose morphological structure was observed by SEM, verifying a good distribution of glass flakes, showing difference orientation in the center and in the surface layer of test body of composites with 10 and 20% of glass flakes. The results of DMTA Tg values of the composites obtained from the peak of tan ä showed little reductions due to poor interfacial adhesion between PET and recycled glass flakes.

Influência de tratamentos térmicos no comportamento mecânico da blenda poli(metacrilato de metila) / poli(tereftalato de etileno) reciclado

Studies indicate that a variation in the degree of crystallinity of the components of a polymer blend influences the mechanical properties. This variation can be obtained by subjecting the blend to heat treatments that lead to changes in the spherulitic structure. The aim of this work is to analyze the influence of different heat treatments on the variation of the degree of crystallinity and to establish a relationship between this variation and the mechanical behavior of poly(methyl methacrylate)/poly(ethylene terephthalate) recycled (PMMA / PETrec) with and without the use of compatibilizer agent poly(methyl methacrylate-al-glycidyl methacrylate-al-ethyl acrylate) (MMAGMA- EA). All compositions were subjected to two heat treatments. T1 heat treatment the samples were treated at 130 ° C for 30 minutes and cooled in air. In T2, the samples were treated at 230 ° C for 5 minutes and cooled to approximately -10 ° C. The variation of the degree of crystallinity was determined by the proportional relationship between crystallinity and density, with the density measured by pycnometry. The mechanical behavior was verified by tensile tests with and without the presence of notches and pre-cracks, and by method of fracture toughness in plane strain (KIC). We used the scanning electron microscopy (SEM) to analyze the fracture surface of the samples. The compositions subjected to heat treatment T1, in general, showed an increase in the degree of crystallinity in tensile strength and a tendency to decrease in toughness, while compositions undergoing treatment T2 showed that the opposite behavior. Therefore, this work showed that heat treatment can give a polymer blend further diversity of its properties, this being caused by changes in the crystal structure

Efeito da adição do poli(etileno acrilato de metila) (ema) e da fibra de linter de algodão nas propriedades do poli(tereftalato de etileno) reciclado (petrec)

The development of new materials to fill the demand of technological advances is a challenge for many researchers around the world. Strategies such as making blends and composites are promising alternatives to produce materials with different properties from those found in conventional polymers. The objective of this study is to evaluate the effect of adding the copolymer poly(ethylene methyl acrylate) (EMA) and cotton linter fibers (LB) on the properties of recycled poly(ethylene terephthalate) (PETrec) by the development of PETrec/EMA blend and PETrec/EMA/LB blend composite. In order to improve the properties of these materials were added as compatibilizers: Ethylene - methyl acrylate - glycidyl methacrylate terpolymer (EMA-GMA) and maleic anhydride grafted polyethylene (PE-g-MA). The samples were produced using a single screw extruder and then injection molded. The obtained materials were characterized by thermogravimetry (TG), melt flow index (MFI) mensurements, torque rheometry, pycnometry to determinate the density, tensile testing and scanning electron microscopy (SEM). The rheological results showed that the addition of the EMA copolymer increased the viscosity of the blend and LB reduces the viscosity of the blend composite. SEM analysis of the binary blend showed poor interfacial adhesion between the PETrec matrix and the EMA dispersed phase, as well as the blend composite of PETrec/EMA/LB also observed low adhesion with the LB fiber. The tensile tests showed that the increase of EMA percentage decreased the tensile strength and the Young s modulus, also lower EMA percentage samples had increased the elongation at break. The blend composite showed an increase in the tensile strength and in the Young`s modulus, and a decrease in the elongation at break. The blend formulations with lower EMA percentages showed better mechanical properties that agree with the particle size analysis which showed that these formulations presented a smaller diameter of the dispersed phase. The blend composite mechanical tests showed that this material is stronger and stiffer than the blend PETrec/EMA, whose properties have been reduced due to the presence of EMA rubbery phase. The use of EMA-GMA was effective in reducing the particle size of the EMA dispersed phase in the PETrec/EMA blend and PE-g-MA showed evidences of reaction with LB and physical mixture with the EMA

Aditivação de pastas geopoliméricas com tetraborato de sódio e látex não iônico para cimentação de Poços de Petróleo

The development of activities in the oil and gas sector has been promoting the search for materials more adequate to oilwell cementing operation. In the state of Rio Grande do Norte, the cement sheath integrity tend to fail during steam injection operation which is necessary to increase oil recovery in reservoir with heavy oil. Geopolymer is a material that can be used as alternative cement. It has been used in manufacturing of fireproof compounds, construction of structures and for controlling of toxic or radioactive waste. Latex is widely used in Portland cement slurries and its characteristic is the increase of compressive strength of cement slurries. Sodium Tetraborate is used in dental cement as a retarder. The addition of this additive aim to improve the geopolymeric slurries properties for oilwell cementing operation. The slurries studied are constituted of metakaolinite, potassium silicate, potassium hydroxide, non-ionic latex and sodium tetraborate. The properties evaluated were: viscosity, compressive strength, thickening time, density, fluid loss control, at ambient temperature (27 ºC) and at cement specification temperature. The tests were carried out in accordance to the practical recommendations of the norm API RP 10B. The slurries with sodium tetraborate did not change either their rheological properties or their mechanical properties or their density in relation the slurry with no additive. The increase of the concentration of sodium tetraborate increased the water loss at both temperatures studied. The best result obtained with the addition of sodium tetraborate was thickening time, which was tripled. The addition of latex in the slurries studied diminished their rheological properties and their density, however, at ambient temperature, it increased their compressive strength and it functioned as an accelerator. The increase of latex concentration increased the presence of water and then diminished the density of the slurries and increased the water loss. From the results obtained, it was concluded that sodium tetraborate and non-ionic latex are promising additives for geopolymer slurries to be used in oilwell cementing operation

Injeção de vapor e solvente como um método de recuperação avançada em reservatório avançada em reservatórios de óleo pesado

Currently a resource more and more used by the petroleum industry to increase the efficiency of steam flood mechanism is the addition of solvents. The process can be understood as a combination of a thermal method (steam injection) with a miscible method (solvent injection), promoting, thus, the reduction of interfacial tensions and oil viscosity. The use of solvent alone tends to be limited because of its high cost. When co-injected with steam, the vaporized solvent condenses in the cooler regions of the reservoir and mixes with the oil, creating a zone of low viscosity between the steam and the heavy oil. The mobility of the displaced fluid is then improved, resulting in an increase of oil recovery. To better understand this improved oil recovery method, a numerical study of the process was done contemplating the effects of some operational parameters (distance between wells, injection steam rate, kind of solvent and injected solvent volume)on the accumulated production of oil, recovery factor and oil-steam rate. Semisynthetic models were used in this study but reservoir data can be extrapolated for practical applications situations on Potiguar Basin. Simulations were performed in STARS (CMG, 2007.11). It was found that injected solvent volumes increased oil recovery and oil rates. Further the majority of the injected solvent was produced and can be recycled

Tecendo Papéis:viagem pelos saberes e práticas do ensino de arte

Nowdays, recycling became a relevant social and educational aim among many other factors, which involve balance between man and nature. This study relates the experiences with the production of recycled handmade paper directed at the teaching in Universidade Federal do Rio Grande do Norte UFRN, and through workshops of carnauba recycled handcrafts papers as a pioneer activity accomplished at the Felix Rodrigues Foundation, in the city of Pendências, Açu Valley, Rio Grande do Norte. A bibliographic review was done about the history of handmade paper and a discussion about carnauba´s paper artistic possibilities in art-education. Analyses within the context of art teaching, accordingly to Ana Mae Barbosa´s triangle propose and, also, Buoro, Ostrower and Nachmanovitch´s pedagogy of art. It deals with a group of artisans in order to establish the nature of their relationship and the possibilities of achieving more ecological awareness. Finally, we intend to realize a dialogue with Morin and other authors

O desafio da parceria na implementação do PRONERA: o caso do projeto alfabetização cidadã no nordeste Paraense.

El desafío de la parcería en la implantación del PRONERA: el caso del Proyecto Alfabetización Ciudadana en Noreste de Pará se constituye en un estudio sobre las políticas públicas de educación del campo. El trabajo tiene como objeto de análisis la implantación del PRONERA, a partir del estudio de caso del Proyecto de Alfabetización Ciudadana en Noreste de Pará, con el objetivo de comprender como la parcería, principio operacional y metodológico propuesto por el PRONERA, se concretó en la implantación del Proyecto y cuales sus posibles implicaciones en las políticas públicas de educación del campo. Entre los procedimientos metodológicos, realizamos la investigación bibliográfica y documental que nos permitieron situar la educación del campo en términos históricos y políticos, sistematizar la constitución y la organización del PRONERA y reflexionar acerca de la parcería a partir de diferentes ópticas. Realizamos también la investigación de campo por medio de entrevistas semi-estructuradas, con el propósito de analizar la implantación del Proyecto da Alfabetización Ciudadana, a partir del dialogo con los actores sociales involucrados. Los resultados de las análisis indicaron que, históricamente, las políticas públicas de educación destinadas a las poblaciones de la zona rural fueron instituidas verticalmente, desvinculadas de la realidad del campo e incompatibles con las necesidades e intereses de los sujetos. Constatamos que, en período reciente, movimientos sociales del campo reivindican y proponen acciones que se establezcan como políticas públicas de educación del campo. Identificamos que el PRONERA resulta de ese movimiento y se presenta como anuncio de una política pública de educación del campo, teniendo como diferencial el hecho de ser un programa del gobierno federal idealizado fuera de la esfera gubernamental, construido por los movimientos sociales del campo y presentar, entre otras innovaciones, el modelo de parcería y la gestión compartida, participativa y democrática. En esta perspectiva, en este estudio de caso, se evidenció que la parcería, frente a los conflictos y las disputas entre sus miembros participantes, no es el problema de la implantación del PRONERA, sino su punto fuerte. De este modo, la parcería es uno de los elementos necesarios para la construcción de políticas públicas, en particular, de educación del campo, una vez que posibilita la interacción de instituciones públicas y movimientos sociales locales, atribuyendo legitimidad a la educación del campo. Al promover un proceso de aprendizaje democrático, la parcería se presenta como estrategia de democratización de la educación del campo.

O Fundef e o Fundeb como política de financiamento para a valorização do magistério: efeitos na carreira e na remuneração dos professores da rede pública estadual de ensino do RN

Le présent étude analyse les effets de la politique de financement de l éducation de base, par les Fonds contables, Fundef et Fundeb, et sa proposition de valorisation de l enseignement, en considerant les dimensions de la carrière et de la rémunération des professeurs de l éducation publique de l état du Rio Grande do Norte, entre les années de 1996 et 2000. Pour comprendre les contraintes de l évaluation des politiques publiques, en cherchant aussi les contribution en Marx (1996) selon qui « le concret est concret » et que la dialétique du concret peut appuyer pour la tentative de capter le fenomène étudié. On a utilisé encore le référentiel bibliographique relatif au financement de l éducation et la valorisation de l enseignement à partir de la littérature reférente aux dimensions de l objet (Fundef et Fundeb) et (carrière et rémuneration). Dans la recherche documental, au-delà des législations, directrices nationales et locales pertinentes, se sont utilisés des donnés référents aux ressources, disponibles à la Finbra, Trésor National, SIOPE/RN, INEP/MEC, des informations du résumé de la feuille et feuille de payement du Secrétariat d État, de l Éducation et de la Culture (SEEC) et 289 bulletins de salaire de 21 professeurs. On a réalisé interview semi structurée avec une quantité de 9 professeurs, reférent à la carrière, et un questionaire appliqué à 12 professeurs relatif à la remuneration. On considère que sur les résultats reférents aux indicateurs éducationnel, dans la période Fundef il y a eu une réduction des inscriptions aux écoles de l état comme aussi aux fonctions des professeurs de l Enseignement Fondamental, et cela correspond à 37%. À partir de la vigence du Fondebe (2007 - 2010) ces indicateurs ont équalisé. Pendant toute la période, 1996 et 2010 il y a eu une augmentation des inscriptions de 119,03%, et aussi aux fonctions des professeurs de 77,44%. Par rapport aux informations de financement, on a constaté que, du minimum exigé (60%) sur l aplication des fonds à la rémuneration de l enseignant, on applique pour la période des deux fonds, plus que le minimum exigé, c est-à-dire de 83,29% à 98,89% des fonds. Les effets des fonds sur la carrière des 9 professeurs n ont pas été satisfactoires, si l on considère la promotion et la progression. Au cas de la promotion des 9 de ces professeurs, un seul a évolué son niveau (les titres) mais a, au même temps, rétroagit dans sa progression. Pour la progression des 9 professeurs, 8 d entre eux ont sa progression retardée, ce qui correspond à entre 2 et 5 classes, et ce qui provoque un préjudice qui varie entre 10% à 45% sur sa remunération. La différence d une classe à l autre correspond à 5% de son salaire. On évalue que les avantages financières contribuent pour la remunération avec un pourcentage plus élevé que son salaire, ce qui diminuent pendant lo Fundeb. Par rapport à la remunération un professeur de 24 ans de service avec formation, n arrive même pas à gagner 2 salaires minimums. Le professeur de 30 ans de service, maître, reçoit un salaire, en 2010, qui correspond a moins de 3 salaires minimums, c est-à-dire, une proportion de 2,82 et une remuneration qui correspond à un peu plus que 3 salaires minimums, c est-à-dire, une proportion de 3,66. L enseignement n est pas très favorisé si on le met face à d autres profession qui ont aussi l exigence de formation supérieure, ce qui provoque un effet négatif pour voir l enseignement comme profession. À propos des effets sur la rémuneration, on conclue qu il y a eu une amélioration mais encore insufisante, surtout si l on compare au Salaire Minimum annuel. On évalue que les fonds Fundef et Fundeb n ont pas été capables de promouvoir la valorisation de l enseignement dans le contexte de carrière et rémuneration. On observe quelques résultats négatif dans la politique de fonds, une fois qu il y aurait en avoir avec l incapacité de tel politique en promouvoir la dite valorisation de l enseignement, ce qui est une des causes, le financement avec des restriction budgétaire

A sistematização do conteúdo jogo nas aulas de educação física do ensino fundamental e médio

Since the enactment of LDBEN 9.9394/96, Physical Education began to be understood as a curricular component in school. Thus, we see the need for systematization of content. We observed that the physical education classes at the public schools in Natal/RN from the game content, teachers did not use the existing proposals for systematization. And it was on this reality that the study occurred, aiming to present and discuss a proposal to systematization the game content in physical education classes in elementary and secondary education. Accordingly, we departed of following question: What possibilities of systematization of the game content in school physical education classes?. The methodology used was the action research, which allowed us to structure the intervention plan for the game content, directed to a reflective didactic process. The dialogue with action research provided an opportunity to understand of the proposal of systematization, the knowledge of game content, the planning and process of teaching and learning in physical education lessons developed. We use the proposed systematization the book Educação Física Escolar e Organização Curricular , to direct and organize the lesson plans. As research technique, we use the participant observation, filming, photographic records and field diary, guiding us in the debates and discussions about the field of research. The applications of the lesson plans were carried out in three schools, all located in Natal / RN: Escola Municipal Professora Ivonete Maciel, Escola Municipal Professor Ulisses de Góis e Professor Escola Estadual Josino Macedo. The members of this study were students PIBID-EF-UFRN, teachers, supervisors and school. They made the bridge between research and action, theoretical foundation and pedagogical practice, university and school. The results were advanced for beyond the propositions submitted by the above-mentioned book. For the Elementary School 1, the proposed systematization broadened experiences and learning of knowledge of the game and of playful and body manifestations. Provided an opportunity to know and learn about game of make account, rules, popular games, cooperative games, among others. For Elementary Schools 2 and Middle education, systematized lessons allowed the practical, the incorporation of knowledge of the game and its features: such as rules, origin, meaning of the name, different denominations, among others. The students experienced and learned, popular games, pre-sport games, cooperative games, with recycled material, among others. The treatment from three dimensions of contents: procedural, conceptual and attitudinal, occurred parallel to approach the game content, and in conjunction with our interventions, not being done separately during practice, but an ongoing process during class. This new perspective of work the game, in a systematized way, with applying, description and discussion the activities, allowed elaborate a summary framework of thematizations for game content, by year of teaching

Avaliação de concreto com adição de fibras de PET submetido a altas temperaturas

The concrete for centuries constituted an essential structural element in the construction industry due to its relative ease of forming, before the weather durability, low cost, its lower maintenance compared to other materials such as steel. However, when the concrete is exposed to high temperatures tends to lose its mechanical characteristics, and may even result in loss of section, which undermines the stability and mechanical strength of structural elements. The pathologies resulting from exposure to elevated temperatures ranging from cracks, pops up chipping explosives (spalling). Recently, the technology of concrete is closely related to the study of its microstructure. The use of fibers added to concrete has been revealed as a solution to increase the mechanical strength of the concrete, it acts directly on the distribution of efforts to act in the play within the microstructure. In this work we used recycled PET fibers embedded in concrete with 15x2mm fck = 30MPa, water/cement ratio of 0.46, in works made for verification of mechanical strength of this mixture submitted to high temperature. The specimens of concrete with addition of PET fibers were tested after exposure to temperatures: ambient (30ºC), 100°C, 200°C, 300°C, 400°C, 600°C and 900°C. It was found that the concrete loses significant strength when exposed to temperatures above 300°C, however the use of fiber PET may delay the risk of collapse of structures for the formation of a network of channels that facilitate the escape of vapor 'water, reducing the pore pressure inside the structural element