Estudo do comportamento da sinterização de compactos de cavacos de um aço SAE 1050 obtidos sob alta pressão

From an economic standpoint, the powder metallurgy (P/M) is a technique widely used for the production of small parts. It is possible, through the P/M and prior comminution of solid waste such as ferrous chips, produce highly dense sintered parts and of interest to the automotive, electronics and aerospace industries. However, without prior comminution the chip, the production of bodies with a density equal to theoretical density by conventional sintering techniques require the use of additives or significantly higher temperatures than 1250ºC. An alternative route to the production of sintered bodies with high density compaction from ferrous chips (≤ 850 microns) and solid phase sintering is a compression technique under high pressure (HP). In this work, different compaction pressures to produce a sintered chip of SAE 1050 carbon steel were used. Specifically, the objective was to investigate them, the effect of high pressure compression in the behavior of densification of the sintered samples. Therefore, samples of the chips from the SAE 1050 carbon steel were uniaxially cold compacted at 500 and 2000 MPa, respectively. The green compacts obtained were sintered under carbon atmosphere at 1100 and 1200°C for 90 minutes. The heating rate used was 20°C/min. The starting materials and the sintered bodies were characterized by optical microscopy, SEM, XRD, density measurements (geometric: mass/volume, and pycnometry) and microhardness measurements Vickers and Rockwell hardness. The results showed that the compact produced under 2000 MPa presented relative density values between 93% and 100% of theoretical density and microhardness between 150 HV and 180 HV, respectively. In contrast, compressed under 500 MPa showed a very heterogeneous microstructure, density value below 80% of theoretical density and structural conditions of inadequate specimens for carrying out the hardness and microhardness measurements. The results indicate that use of the high pressure of ferrous chips compression is a promising route to improve the sinterability conditions of this type of material, because in addition to promoting greater compression of the starting material, the external tension acts together with surface tension, functioning as the motive power for sintering process. Additionally, extremely high pressures allow plastic deformation of the material, providing an intimate and extended contact of the particles and eliminating cracks and pores. This tends to reduce the time and / or temperature required for good sintering, avoiding excessive grain growth without the use of additives. Moreover, higher pressures lead to fracture the grains in fragile or ductile materials highly hardened, which provides a starting powder for sintering, thinner, without the risk of contamination present when previous methods are used comminution of the powder.

Degradação do PMMA através da reação despolimerização uitlizando catalisadores de óxidos mistos

In this work, mixed oxides were synthesized by two methods: polymeric precursor and gel-combustion. The oxides, Niquelate of Lanthanum, Cobaltate of Lanthanum and Cuprate of Lanthanum were synthesized by the polymeric precursor method, and treated at 300 º C for 2 hours, calcined at 800 º C for 6h in air atmosphere. In gel-combustion method were produced and oxides using urea and citric acid as fuel, forming for each fuel the following oxides Ferrate of Lanthanum, Cobaltato of Lanthanum and Ferrato of Cobalt and Lanthanum, which were submitted to the combustion process assisted by microwave power maximum of 10min. The samples were characterized by: thermogravimetric analysis, X-ray diffraction; fisisorção of N2 (BET method) and scanning electron microscopy. The reactions catalytic of depolymerization of poly (methyl methacrylate), were performed in a reactor of silica, with catalytic and heating system equipped with a data acquisition system and the gas chromatograph. For the catalysts synthesized using the polymeric precursor method, the cuprate of lanthanum was best for the depolymerization of the recycled polymer, obtaining 100% conversion in less time 554 (min), and the pure polymer, was the Niquelate of Lanthanum, with 100% conversion in less time 314 (min). By gel-combustion method using urea as fuel which was the best result obtained Ferrate of Lanthanum for the pure polymer with 100% conversion in less time 657 (min), and the recycled polymer was Cobaltate of Lanthanum with 100 % conversion in less time 779 (min). And using citric acid to obtain the best result for the pure polymer, was Ferrate of Lanthanum with 100% conversion in less time 821 (min and) for the recycled polymer, was Ferrate of Lanthanum with 98.28% conversion in less time 635 (min)

A rede de marcação e recaptura: o caso de borboletas do gênero heliconius

(The Mark and Recapture Network: a Heliconius case study). The current pace of habitat destruction, especially in tropical landscapes, has increased the need for understanding minimum patch requirements and patch distance as tools for conserving species in forest remnants. Mark recapture and tagging studies have been instrumental in providing parameters for functional models. Because of their popularity, ease of manipulation and well known biology, butterflies have become model in studies of spatial structure. Yet, most studies on butterflies movement have focused on temperate species that live in open habitats, in which forest patches are barrier to movement. This study aimed to view and review data from mark-recapture as a network in two species of butterfly (Heliconius erato and Heliconius melpomene). A work of marking and recapture of the species was carried out in an Atlantic forest reserve located about 20km from the city of Natal (RN). Mark recapture studies were conducted in 3 weekly visits during January-February and July-August in 2007 and 2008. Captures were more common in two sections of the dirt road, with minimal collection in the forest trail. The spatial spread of captures was similar in the two species. Yet, distances between recaptures seem to be greater for Heliconius erato than for Heliconius melpomene. In addition, the erato network is more disconnected, suggesting that this specie has shorter traveling patches. Moving on to the network, both species have similar number of links (N) and unweighed vertices (L). However, melpomene has a weighed network 50% more connections than erato. These network metrics suggest that erato has more compartmentalized network and restricted movement than melpomene. Thus, erato has a larger number of disconnected components, nC, in the network, and a smaller network diameter. The frequency distribution of network connectivity for both species was better explained by a Power-law than by a random, Poissom distribution, showing that the Power-law provides a better fit than the Poisson for both species. Moreover, the Powerlaw erato is much better adjusted than in melpomene, which should be linked to the small movements that erato makes in the network

Relações de poder, fragmentação e gestão do território no semi-árido nordestinho: um outro olhar sobre o Cariri paraibano

This study aims to analize the Cariri Paraibano territory, as a product of relations of power that were being established along its historic process of territory formation. In this process, the fragmentation and the territory management are fundamental elements to socioterritorial reality comprehension. The theoretical-conceptual basis is based on notions of territory, region, power and territory management, which are articulated to the opinions and empiric confirmations origined from interviews made with several social actions. They also were made photographical records and researches on books, newspapers and magazines, as well on other information sources related to the object of studying. Obtained data confirm the pressuposement on which the relations of dominations and the used methods by the power s owners in the region created a little fruitful political practice and little adequate to the process of active participation of the local population on the territory management, even being on disagreement with the new political-institutional mechanisms, which take to political-administrative more democratic and participative in the country

Novas fronteiras petrolíferas no Brasil : uma análise da necessidade de nova regulamentação da área do pré-sal sob a ótica constitucional

The Oil industry in Brazil has gone through several stages during the economical, political and social historical process. However, the significative changes have happened in the last fifteen years, due to market opening arising from the relaxation of the state monopoly over the Oil deposits and its derivatives. The edition of the Constitutional Amendment #9, changing the first paragraph of the 177th item of the Federal Constitution, marked the end of a stiffness about the monopoly that the Brazilian state kept in relation to the exploration and research of Oil and Gas. The economical order was fundamental to actualize the idea contained in the #9 Amendment, since its contents has the power to set up measures to be adopted by public power in order to organize the economical relations from a social viewpoint. The new brazilian Oil scenery, called pre-salt, presents itself in a way to amaze the economical markets, in addition to creating a new perspective to the social sector. This work will identify, in this new scenario, the need for change in the legal system. Nevertheless, this subject must not be treated in a thoughtless way: being an exhaustible good, we shall not forget that the future generations also must benefit from the exploration of natural resources recently discovered. The settlement of a new regulatory mark, including the change in the concession contract model to production and sharing is one of the suggested solutions as a bill in the National Congress, in an attempt to ensure the sovereignty of the nation. The constitutionality of a new regulatory mark is questioned, starting from an analysis of the state monopoly, grounding the comprehnsions in the brazilian constitutions, the relevance of the creation of Petrobras for self-assertion of the state about the monopoly of Oil and derivatives, and its posture after the Constitutional Amendment nº 9 (1995), when a company stops having control of the state monopoly, beginning to compete in a fairly way with other companies. The market opening and private initiative are emphasized from the viewpoint of the Constitutional Principles of the Economical and Social Order. The relaxation of the monopoly regarding the exploratory activity in the Federal Constitution doesn't deprive from the Union the ownerships of underground goods, enabling to this federal entity to contract, directly or by concession of exploration of goods, to state-owned or private companies. The existing oil in the pre-salt layer transforms the scenario from very high risk to low risk, which gives the Union the possibility of defining another way of exploring this resources in the best interests of the Public Administration

Dedução de Funções de Alívio para Priorização de Variantes de Chaveamento Adequadas à Eliminação de Sobrecargas

Eventually, violations of voltage limits at buses or admissible loadings of transmission lines and/or power transformers may occur by the power system operation. If violations are detected in the supervision process, corrective measures may be carried out in order to eliminate them or to reduce their intensity. Loading restriction is an extreme solution and should only be adopted as the last control action. Previous researches have shown that it is possible to control constraints in electrical systems by changing the network topology, using the technique named Corrective Switching, which requires no additional costs. In previous works, the proposed calculations for verifying the ability of a switching variant in eliminating an overload in a specific branch were based on network reduction or heuristic analysis. The purpose of this work is to develop analytical derivation of linear equations to estimate current changes in a specific branch (due to switching measures) by means of few calculations. For bus-bar coupling, derivations will be based on short-circuit theory and Relief Function methodology. For bus-bar splitting, a Relief Function will be derived based on a technique of equivalent circuit. Although systems of linear equations are used to substantiate deductions, its formal solution for each variant, in real time does not become necessary. A priority list of promising variants is then assigned for final check by an exact load flow calculation and a transient analysis using ATP Alternative Transient Program. At last, results obtained by simulation in networks with different features will be presented

Polaritons em materiais magnéticos nanoestruturados

In this work we present a theoretical study about the properties of magnetic polaritons in superlattices arranged in a periodic and quasiperiodic fashíons. In the periodic superlattice, in order to describe the behavior of the bulk and surface modes an effective medium approach, was used that simplify enormously the algebra involved. The quasi-periodic superlattice was described by a suitable theoretical model based on a transfer-matrix treatment, to derive the polariton's dispersion relation, using Maxwell's equations (including effect of retardation). Here, we find a fractal spectra characterized by a power law for the distribution of the energy bandwidths. The localization and scaling behavior of the quasiperiodic structure were studied for a geometry where the wave vector and the external applied magnetic field are in the same plane (Voigt geometry). Numerical results are presented for the ferromagnet Fe and for the metamagnets FeBr2 and FeCl2

Estudo de um sistema de frenagem eletromagnética empregando correntes parasitas

This work deals with the analytical, computational and experimental study of phenomena related to the Eddy current induction in low permeability means for embedded electromagnetic braking systems applications. The phenomena of forces generation in opposing to the variation of stationary magnetic flux produced by DC power supplies, set in motion by the application of an external propulsive force are addressed. The study is motivated by search for solving the problem of speed control of PIGs used to verifying and maintaining pipelines, and is led based on the analytical models synthesis, validated by means of computer simulations in Finite Elements environment, provided by engineering support software; and with experimental tests conducted under controlled laboratory conditions. Finally, a damping systems design methodology based on analyzes results conducted throughout the study is presented

Estudo da absorção das espécies pesadas do gás natural em octanol: efeitos da temperatura e vazão

In the oil industry, natural gas is a vital component of the world energy supply and an important source of hydrocarbons. It is one of the cleanest, safest and most relevant of all energy sources, and helps to meet the world's growing demand for clean energy in the future. With the growing share of natural gas in the Brazil energy matrix, the main purpose of its use has been the supply of electricity by thermal power generation. In the current production process, as in a Natural Gas Processing Unit (NGPU), natural gas undergoes various separation units aimed at producing liquefied natural gas and fuel gas. The latter should be specified to meet the thermal machines specifications. In the case of remote wells, the process of absorption of heavy components aims the match of fuel gas application and thereby is an alternative to increase the energy matrix. Currently, due to the high demand for this raw gas, research and development techniques aimed at adjusting natural gas are studied. Conventional methods employed today, such as physical absorption, show good results. The objective of this dissertation is to evaluate the removal of heavy components of natural gas by absorption. In this research it was used as the absorbent octyl alcohol (1-octanol). The influence of temperature (5 and 40 °C) and flowrate (25 and 50 ml/min) on the absorption process was studied. Absorption capacity expressed by the amount absorbed and kinetic parameters, expressed by the mass transfer coefficient, were evaluated. As expected from the literature, it was observed that the absorption of heavy hydrocarbon fraction is favored by lowering the temperature. Moreover, both temperature and flowrate favors mass transfer (kinetic effect). The absorption kinetics for removal of heavy components was monitored by chromatographic analysis and the experimental results demonstrated a high percentage of recovery of heavy components. Furthermore, it was observed that the use of octyl alcohol as absorbent was feasible for the requested separation process.

Estudo da absorção das espécies pesadas do gás natural em octanol: efeitos da temperatura e vazão

In the oil industry, natural gas is a vital component of the world energy supply and an important source of hydrocarbons. It is one of the cleanest, safest and most relevant of all energy sources, and helps to meet the world's growing demand for clean energy in the future. With the growing share of natural gas in the Brazil energy matrix, the main purpose of its use has been the supply of electricity by thermal power generation. In the current production process, as in a Natural Gas Processing Unit (NGPU), natural gas undergoes various separation units aimed at producing liquefied natural gas and fuel gas. The latter should be specified to meet the thermal machines specifications. In the case of remote wells, the process of absorption of heavy components aims the match of fuel gas application and thereby is an alternative to increase the energy matrix. Currently, due to the high demand for this raw gas, research and development techniques aimed at adjusting natural gas are studied. Conventional methods employed today, such as physical absorption, show good results. The objective of this dissertation is to evaluate the removal of heavy components of natural gas by absorption. In this research it was used as the absorbent octyl alcohol (1-octanol). The influence of temperature (5 and 40 °C) and flowrate (25 and 50 ml/min) on the absorption process was studied. Absorption capacity expressed by the amount absorbed and kinetic parameters, expressed by the mass transfer coefficient, were evaluated. As expected from the literature, it was observed that the absorption of heavy hydrocarbon fraction is favored by lowering the temperature. Moreover, both temperature and flowrate favors mass transfer (kinetic effect). The absorption kinetics for removal of heavy components was monitored by chromatographic analysis and the experimental results demonstrated a high percentage of recovery of heavy components. Furthermore, it was observed that the use of octyl alcohol as absorbent was feasible for the requested separation process.

Degradação do PMMA através da reação despolimerização uitlizando catalisadores de óxidos mistos

In this work, mixed oxides were synthesized by two methods: polymeric precursor and gel-combustion. The oxides, Niquelate of Lanthanum, Cobaltate of Lanthanum and Cuprate of Lanthanum were synthesized by the polymeric precursor method, and treated at 300 º C for 2 hours, calcined at 800 º C for 6h in air atmosphere. In gel-combustion method were produced and oxides using urea and citric acid as fuel, forming for each fuel the following oxides Ferrate of Lanthanum, Cobaltato of Lanthanum and Ferrato of Cobalt and Lanthanum, which were submitted to the combustion process assisted by microwave power maximum of 10min. The samples were characterized by: thermogravimetric analysis, X-ray diffraction; fisisorção of N2 (BET method) and scanning electron microscopy. The reactions catalytic of depolymerization of poly (methyl methacrylate), were performed in a reactor of silica, with catalytic and heating system equipped with a data acquisition system and the gas chromatograph. For the catalysts synthesized using the polymeric precursor method, the cuprate of lanthanum was best for the depolymerization of the recycled polymer, obtaining 100% conversion in less time 554 (min), and the pure polymer, was the Niquelate of Lanthanum, with 100% conversion in less time 314 (min). By gel-combustion method using urea as fuel which was the best result obtained Ferrate of Lanthanum for the pure polymer with 100% conversion in less time 657 (min), and the recycled polymer was Cobaltate of Lanthanum with 100 % conversion in less time 779 (min). And using citric acid to obtain the best result for the pure polymer, was Ferrate of Lanthanum with 100% conversion in less time 821 (min and) for the recycled polymer, was Ferrate of Lanthanum with 98.28% conversion in less time 635 (min)

A rede de marcação e recaptura: o caso de borboletas do gênero heliconius

(The Mark and Recapture Network: a Heliconius case study). The current pace of habitat destruction, especially in tropical landscapes, has increased the need for understanding minimum patch requirements and patch distance as tools for conserving species in forest remnants. Mark recapture and tagging studies have been instrumental in providing parameters for functional models. Because of their popularity, ease of manipulation and well known biology, butterflies have become model in studies of spatial structure. Yet, most studies on butterflies movement have focused on temperate species that live in open habitats, in which forest patches are barrier to movement. This study aimed to view and review data from mark-recapture as a network in two species of butterfly (Heliconius erato and Heliconius melpomene). A work of marking and recapture of the species was carried out in an Atlantic forest reserve located about 20km from the city of Natal (RN). Mark recapture studies were conducted in 3 weekly visits during January-February and July-August in 2007 and 2008. Captures were more common in two sections of the dirt road, with minimal collection in the forest trail. The spatial spread of captures was similar in the two species. Yet, distances between recaptures seem to be greater for Heliconius erato than for Heliconius melpomene. In addition, the erato network is more disconnected, suggesting that this specie has shorter traveling patches. Moving on to the network, both species have similar number of links (N) and unweighed vertices (L). However, melpomene has a weighed network 50% more connections than erato. These network metrics suggest that erato has more compartmentalized network and restricted movement than melpomene. Thus, erato has a larger number of disconnected components, nC, in the network, and a smaller network diameter. The frequency distribution of network connectivity for both species was better explained by a Power-law than by a random, Poissom distribution, showing that the Power-law provides a better fit than the Poisson for both species. Moreover, the Powerlaw erato is much better adjusted than in melpomene, which should be linked to the small movements that erato makes in the network