Efeito da adição de colesterol e ecdisona na produção in vitro do baculovírus spodoptera frugiperda MNPV

Among the pests that attack corn crop in Brazil, there is Spodoptera frugiperda (JE Smith, 1797) (Lepidoptera: Noctuidae), known as fall armyworm, which is the major corn pest. Due to genetic instability during serial passage of baculoviruses in insect cell culture, the viral bioinseticides in vitro production development is the greatest challenge for mass production of this bioproduct. Successive passages of virus using extracellular viruses (BVs), necessary during viral bioinseticides production scaling up, leads to the appearance of aberrant forms of virus, a process so called as "passage effect ". The main consequence of passage effect is the production of occlusion bodies (OB) decrease, preventing its production using in vitro process. In this study, it was carried out a serial passage of baculovirus Spodoptera frugiperda multiple nucleopolyhedrovirus, isolate 18, using Sf21 cells. A decrease in the production of occlusion bodies from 170 to 92 in the third to fourth passage was observed. A factorial experimental design (22) was employed to verify the influence of two input variables, concentration of the hormone 20 - hydroxyecdysone (CH) and cholesterol (CC) on the values of response variables (volumetric and the specific OB production) of the process, seeking to define the optimum operating ranges trying to reverse or minimize the passage effect. The result indicated a negative influence of the cholesterol addition and positive effect in the hormone supplementation which the optimum range found for the concentrations studied were 8 to 10μg/mL and 5 to 6.5 mg / mL, for cholesterol and hormone concentrations respectively. New experiments were performed with addition of hormone and cholesterol in order to check the influence of these additives on the OB production independently. While the best result obtained from the factorial experiment was 9.4 x 107 OB/mL and 128.4 specific OB/cell, with the addition of only 6μg/mL 20-hydroxyecdysone these concentrations increased to 1.9 x 108 OB/mL and 182.9 OB/cell for volumetric and specific OB production, respectively. This result confirms that the addition of the hormone 20-hydroxyecdysone enhances the SfMNPV in vitro production process performance using Sf21 cells

Vicilina de sementes da leguminosa selvagem Anadenanthera macrocarpa (AmV): purificação, caracterização, efeito deletério e mecanismo de ação para bruquídeo callosobruchus maculatus

Grains and legume seeds are foods that form the basis of the diets of many cultures around the world, winch contritbute to the daily nutrient requirements of humans. Vicilins (7S globulin) are storage proteins found in legume seeds, and may have an additional function constitutive defense of the embryo against pests and pathogens. In this work the vicilin from Anadenanthera macrocarpa - AmV (red-angico), was purified and partially characterized, its effect on development and larval survival and adult emergence of Callosobruchus maculatus was evaluated by determination of LD50, WD50 and ED50 in system bioassay. Purification of vicilin was initiated by the chitin affinity chromatography and then gel filtration (Superdex 75 Tricorn 10x300 mm) FPLC system followed by reverse phase chromatography (C8 phenomenex) on HPLC system. Bioassays WD50 and LD50 for larvae were 0.32% and 0.33% (w:w) respectively, since the ED50 for adults was 0.096%. The probable mechanism of action was evaluated by testing digestibility of AmV in vitro, and observed for the involvement of two fragments vicilins immunoreactive against polyclonal Anti-vicilin from Erythrina velutina (Anti-EvV) about of 22 and 13 kDa chitin binding. The AmV in its native form has been recognized by the anti-EvV, indicating that there is a conserved region in the vicilin and is probably corresponding to the chitin binding domains. These results point to a new vicilin chitin binding that can subsequently be used as a possible biopesticide protein source, in order to control insect pest C. maculatus and confirm literature findings that demonstrate vicilin in the presence of different kinds of ligands to conserved regions chitin not yet characterized

Contribuição ao desenvolvimento de ontologias para processos petroquímicos : estudo de caso em uma planta DEA

In the last decades, the oil, gas and petrochemical industries have registered a series of huge accidents. Influenced by this context, companies have felt the necessity of engaging themselves in processes to protect the external environment, which can be understood as an ecological concern. In the particular case of the nuclear industry, sustainable education and training, which depend too much on the quality and applicability of the knowledge base, have been considered key points on the safely application of this energy source. As a consequence, this research was motivated by the use of the ontology concept as a tool to improve the knowledge management in a refinery, through the representation of a fuel gas sweetening plant, mixing many pieces of information associated with its normal operation mode. In terms of methodology, this research can be classified as an applied and descriptive research, where many pieces of information were analysed, classified and interpreted to create the ontology of a real plant. The DEA plant modeling was performed according to its process flow diagram, piping and instrumentation diagrams, descriptive documents of its normal operation mode, and the list of all the alarms associated to the instruments, which were complemented by a non-structured interview with a specialist in that plant operation. The ontology was verified by comparing its descriptive diagrams with the original plant documents and discussing with other members of the researchers group. All the concepts applied in this research can be expanded to represent other plants in the same refinery or even in other kind of industry. An ontology can be considered a knowledge base that, because of its formal representation nature, can be applied as one of the elements to develop tools to navigate through the plant, simulate its behavior, diagnose faults, among other possibilities

Desenvolvimento de um sistema de automação para uma planta de inertização de resíduos por plasma

The traditional processes for treatment of hazardous waste are questionable for it generates other wastes that adversely affect people s health. As an attempt to minimize these problems, it was developed a system for treatment of hazardous waste by thermal plasma, a more appropriate technology since it produces high temperatures, preventing the formation of toxic pollutants to human beings. The present work brings out a solution of automation for this plant. The system has local and remote monitoring resources to ensure the operators security as well as the process itself. A special attention was given to the control of the main reactor temperature of the plant as it is the place where the main processing occurs and because it presents a complex mathematical model. To this, it was employed cascaded controls based on Fuzzy logic. A process computer, with a particular man-machine interface (MMI), provides information and controls of the plant to the operator, including by Internet. A compact PLC module is in charge of the central element of management automation and plant control which receives information from sensors, and sends it to the MMI

Identificação de uma planta de corrente de um motor de indução utilizando redes de base radial

The present work describes the use of a mathematical tool to solve problems arising from control theory, including the identification, analysis of the phase portrait and stability, as well as the temporal evolution of the plant s current induction motor. The system identification is an area of mathematical modeling that has as its objective the study of techniques which can determine a dynamic model in representing a real system. The tool used in the identification and analysis of nonlinear dynamical system is the Radial Basis Function (RBF). The process or plant that is used has a mathematical model unknown, but belongs to a particular class that contains an internal dynamics that can be modeled.Will be presented as contributions to the analysis of asymptotic stability of the RBF. The identification using radial basis function is demonstrated through computer simulations from a real data set obtained from the plant

Desenvolvimento de uma planta piloto para estudos de poços de petróleo produzindo por plunger lift

This document proposes to describe a pilot plant for oil wells equipped with plunger lift. In addition to a small size (21,5 meters) and be on the surface, the plant s well has part of its structure in transparent acrylic, allowing easy visualization of phenomena inherent to the method. The rock formation where the well draws its pilot plant fluids (water and air) is simulated by a machine room where they are located the compressor and water pump for the production of air and water. To keep the flow of air and water with known and controlled values the lines that connect the machine room to the wellhole are equipped with flow sensors and valves. It s developed a supervisory system that allows the user a real-time monitoring of pressures and flow rates involved. From the supervisor is still allowed the user can choose how they will be controlled cycles of the process, whether by time, pressure or manually, and set the values of air flow to the water used in cycles. These values can be defined from a set point or from the percentage of valve opening. Results from tests performed on the plant using the most common forms of control by time and pressure in the coating are showed. Finally, they are confronted with results generated by a simulator configured with the the pilot plant s feature

Análise de um controlador baseado no Jacobiano estimado da planta através de uma rede neural

This work presents an analysis of the control law based on an indirect hybrid scheme using neural network, initially proposed for O. Adetona, S. Sathanathan and L. H. Keel. Implementations of this control law, for a level plant of second order, was resulted an oscillatory behavior, even if the neural identifier has converged. Such results had motivated the investigation of the applicability of that law. Starting from that, had been made stability mathematical analysis and several implementations, with simulated plants and with real plants, for analyze the problem. The analysis has been showed the law was designed being despised some components of dynamic of the plant to be controlled. Thus, for plants that these components have a significant influence in its dynamic, the law tends to fail

Modelagem e controle adaptativo de uma planta didática de nível com instrumentação industrial

The control, automation and optimization areas help to improve the processes used by industry. They contribute to a fast production line, improving the products quality and reducing the manufacturing costs. Didatic plants are good tools for research in these areas, providing a direct contact with some industrial equipaments. Given these capabilities, the main goal of this work is to model and control a didactic plant, which is a level and flow process control system with an industrial instrumentation. With a model it is possible to build a simulator for the plant that allows studies about its behaviour, without any of the real processes operational costs, like experiments with controllers. They can be tested several times before its application in a real process. Among the several types of controllers, it was used adaptive controllers, mainly the Direct Self-Tuning Regulators (DSTR) with Integral Action and the Gain Scheduling (GS). The DSTR was based on Pole-Placement design and use the Recursive Least Square to calculate the controller parameters. The characteristics of an adaptive system was very worth to guarantee a good performance when the controller was applied to the plant

Projeto de um Transformador utilizado em uma Planta de Plasma

This work discusses the design of a transformer used in a plant plasma. This plant, which is being developed in UFRN, will be used in the treatment of waste. It consists basically of a radio frequency power supply and a inductive plasma torch. The transformer operates at the nominal frequency of 400 kHz, with 50 kW, allowing the adaptation of impedance between the power supply and torch. To develop the project, a study was done on the fabrication technologies and physical effects on the frequency of operation. This was followed by the modeling of this transformer. Finally, simulations and tests were conducted to validate the design

Estratégias de Produção in vitro de Bioinseticida Viral: influências do Isolado, da Cinética e do Modo de operação

Societal concerns about environmental sustainability has lead to the development of ecologically-friendly alternatives to chemical insecticides for crop protection. One such alternative is biological pest control. In particular, baculoviruses are well suited as insect biopesticides due to their narrow host specificity and relative ease of propagation. In Brazil, the baculovirus Anticarsia gemmatalis nucleopolyhedrovirus (AgMNPV) is the main biological control agent employed for the soybean pest, Anticarsia gemmatalis. This baculovirus biopesticide is currently produced using caterpillars, but increasing market demand for the product has encouraged the development of an in vitro manufacturing process, which can be scaled up to much higher virus productivities. In this study, three wild-type AgMNPV isolates (AgMNPV-2D, AgMNPV-MP2 and AgMNPV-MP5) and a recombinant form (vAgEGT-LacZ) were characterised in terms of occlusion body (OB) production and infection kinetics, to enable future optimisation of the in vitro production process. These viruses were propagated using a Spodoptera frugiperda (IPLB-SF21) insect cell line grown in shaker-flask batch cultures. Among the virus isolates tested, AgMNPV-MP5 was found to be the best producer, yielding (5.3±0.85)x108 OB/mL after 8 days post infection. The characterisation of vAgEGT-LacZ propagation in suspension cell cultures has not been previously reported in the literature; hence it became the main focus for this thesis. In particular, it was carried out a study on the effect of the multiplicity of infection (MOI) on OB production. Five successive batches were performed getting a final production (8.9±1.42)x1014 occlusion bodies, considering that production is related for a bioreactor with final volume of 10m3. A low MOI associated with a fed-batch process for vAgEGT-LacZ production was found to support a 3-fold higher OB yield when compared to the default batch process (1.8x107 and 5.3x107 OB/mL, respectively). This yield is competitive with regards to the production process.

Atividades biológicas de extratos salinos de sementes de plantas da caatinga contra Aedes Aegypti e investigação da participação de proteínas bioativas

Dengue fever, currently the most important arbovirus, is transmitted by the bite of the Aedes aegypti mosquito. Given the absence of a prophylactic vaccine, the disease can only be controlled by combating the vector insect. However, increasing reports of resistance and environmental damage caused by insecticides have led to the urgent search for new safer alternatives. Twenty - um plant s eed extracts from the Caatinga were prepared , tested and characterized . Sodium phosphate ( 50 mM pH 8.0) was used as extractor. All extracts showed larvicidal and ovipositional deterrence activity . Extracts of D. grandiflora, E. contortisiliquum, A. cearenses , C. ferrea and C. retusa were able to attract females for posture when in low co ncentration . In the attractive concentrations, the CE of E. contortisiliquum and A. cearenses were able to kill 52% and 100% of the larvae respectively . The extracts of A. cearenses , P. viridiflora, E. velutina, M. urundeuva and S. brasiliensis were also pupicides, while extracts of P. viridiflora, E. velutina, E. contortisiliquum , A. cearenses, A. colubrina, D. grandiflora , B. cheilantha , S. spectabilis, C. pyramidalis, M. regnelli e G. americana displayed adulticidal activity. All extracts were toxic to C. dubia zooplankton . The EB of E. velutina and E. contortisiliquum did not affect the viability of fibroblasts . In all extracts were identified at least two potential insecticidal proteins such as enzyme inhibitors, lectins and chitin - binding proteins and components of secondary metabolism . Considering all bioassays , the extracts from A. cearenses, P. viridiflora, E. contortisiliquum , S. brasiliensis, E. velutina and M. urundeuva were considered the most promising . The E. contortisiliquum extracts was the only one who did not show pupicida activity, indicating that its mechanism of action larvicide and adulticidal is related only to the ingesti on of toxic compounds by insect , so it was selected to be fragmenting. As observed for the CE , th e protein fractions of E. contortisiliquum also showed larvicidal activity, highlighting that F2 showed higher larvicidal activity and lower en vironmental toxicity than the CE source. The reduction in the proteolytic activity of larvae fed with crude extra ct and fractions of E. contortisiliquum suggest ed that the trypsin inhibitors ( ITEc) would be resp onsible for larvicidal activity . However the increase in the purification of this inhibitor resulted in loss of larvicidal activity , but the absence of trypsin inhibitor reduced the effectiveness of the fractions , indicating that the ITEC contributes to the larvicidal activity of this extract. Not been observed larvicidal activity and adulticide in rich fraction vicilin, nor evidence of the contribution o f this molecule for the larvicidal activity of the extract. The results show the potential of seeds from plant extracts of Caatinga as a source of active molecules against insects A. aegypti at different stages of its development cycle, since they are comp osed of different active compounds, including protein nature, which act on different mechanisms should result in the death of insec

Otimização do sistema de supervisão e controle de uma planta de tratamento de resíduos utilizando plasma

A major and growing problems faced by modern society is the high production of waste and related effects they produce, such as environmental degradation and pollution of various ecosystems, with direct effects on quality of life. The thermal treatment technologies have been widely used in the treatment of these wastes and thermal plasma is gaining importance in processing blanketing. This work is focused on developing an optimized system of supervision and control applied to a processing plant and petrochemical waste effluents using thermal plasma. The system is basically composed of a inductive plasma torch reactors washing system / exhaust gases and RF power used to generate plasma. The process of supervision and control of the plant is of paramount importance in the development of the ultimate goal. For this reason, various subsidies were created in the search for greater efficiency in the process, generating events, graphics / distribution and storage of data for each subsystem of the plant, process execution, control and 3D visualization of each subsystem of the plant between others. A communication platform between the virtual 3D plant architecture and a real control structure (hardware) was created. The goal is to use the concepts of mixed reality and develop strategies for different types of controls that allow manipulating 3D plant without restrictions and schedules, optimize the actual process. Studies have shown that one of the best ways to implement the control of generation inductively coupled plasma techniques is to use intelligent control, both for their efficiency in the results is low for its implementation, without requiring a specific model. The control strategy using Fuzzy Logic (Fuzzy-PI) was developed and implemented, and the results showed satisfactory condition on response time and viability

Reaproveitamento de condensado e vapor flash em uma planta têxtil com ênfase no setor de acabamento

This study focused object a steam generation system, steam distribution and condensate return a textile plant located in Rio Grande do Norte. The work was based on the following objectives: Knowing the use of saturated water vapor in the dyeing and finishing processes in a textile plant; To study the various aspects of a steam distribution system to identify the ways in which energy losses occur; Obtain quantitative information of the main loss in steam generation system and steam distribution and to measure the losses, water and steam system; Using the flash steam as a means of cost reduction. For it was made use of the calculation of financial gains made in their respective improvements. As a database for the development of working registers are used in industrial processes, data from utility systems, laboratory data analysis and on-line analyzers, covering the period 2013. Using the principles set conservation laws mass and energy, those data showed that the loss of water and energy in the steam system are significant and that the environmental and economic gains to be obtained with improvement actions are quite significant. Based on the data and results suggest that future studies deem the continuity approach to steam generation systems, distribution and mainly condensate return.

Lâminas de água salina e doses de adubação orgânica na produção de palma Miúda adensada no semiárido

Cactus pear is an important forage for livestock in semi-arid region of Brazil, due to its adaptation to climate conditions in this region, high productivity and nutritional value. The yield of this cactus has positively responded to techniques such as planting density, fertilization and cutting managements, however, in Rio Grande do Norte State, only certain areas have favorable climate conditions to the development of this crop. Drip irrigation, with a small amount of water, has proven to be an alternative to the viability of cactus pear cultivation in these areas. The research aimed to evaluate the effects of different levels of saline water and manure organic fertilization on the morphological characteristics and production of fresh and dry matter of the prickly-pear cactus cv. Miúda (Nopalea cochenillifera Salm Dick) in a dense planting system. The experiment was conducted at the Experimental Station of Terras Secas (EMPARN), Pedro Avelino, latitude 5°31'21" South and longitude 36°23'14" West. The soil was classified as Typical Cambisol Haplicum Carbonate and the water used in irrigation, C4S1T3 (5,25 dS.m-1), with planting spacing of 2.0 x 0.25 m (20,000 plants ha-1). A completely randomized design in a split plot was used, where water levels (0, 7.5, 15.0 and 30.0 mm month-1) with 10 days intervals, were the main plots and organic fertilization (0 , 25 and 50 Mg ha-1 yr-1) the subplots, with four replicates. The measured morphological characteristics were number of cladodes, height and volume of the plant; length, width, perimeter, thickness, area and cladodes area index, fresh and dry matter production, dry matter content, water use efficiency (WUE) and damage promoted by cochineal pest (Diaspis echinocacti) and soft rot (Erwinia carotovora). There was no influence (P>0.05) of organic fertilization on most variables, particularly in relation to the production of fresh and dry matter. The water levels had a significant influence (P<0.05) on most variables, promoting higher height and volume of the plants, larger and thicker cladodes, and increase on fresh and dry matter production (13.55 Mg DM ha-1 yr-1). The absence of irrigation caused a significant expansion in plant damage caused by the cochineal pest and when irrigated with different water levels there was an increase in damage and stand loss, caused by soft rot, been more intense at the higher water level.

Vicilina de sementes da leguminosa selvagem Anadenanthera macrocarpa: purificação, caracterização, efeito deletério e mecanismo de ação para Callosobruchus maculatus

Grains and legume seeds are foods that form the basis of the diets of many cultures around the world, winch contritbute to the daily nutrient requirements of humans. Vicilins (7S globulin) are storage proteins found in legume seeds, and may have an additional function constitutive defense of the embryo against pests and pathogens. In this work the vicilin from Anadenanthera macrocarpa - AmV (red-angico), was purified and partially characterized, its effect on development and larval survival and adult emergence of Callosobruchus maculatus was evaluated by determination of LD50, WD50 and ED50 in system bioassay. Purification of vicilin was initiated by the chitin affinity chromatography and then gel filtration (Superdex 75 Tricorn 10x300 mm) FPLC system followed by reverse phase chromatography (C8 phenomenex) on HPLC system. Bioassays WD50 and LD50 for larvae were 0.32% and 0.33% (w:w) respectively, since the ED50 for adults was 0.096%. The probable mechanism of action was evaluated by testing digestibility of AmV in vitro, and observed for the involvement of two fragments vicilins immunoreactive against polyclonal Anti-vicilin from Erythrina velutina (Anti-EvV) about of 22 and 13 kDa chitin binding. The AmV in its native form has been recognized by the anti-EvV, indicating that there is a conserved region in the vicilin and is probably corresponding to the chitin binding domains. These results point to a new vicilin chitin binding that can subsequently be used as a possible biopesticide protein source, in order to control insect pest C. maculatus and confirm literature findings that demonstrate vicilin in the presence of different kinds of ligands to conserved regions chitin not yet characterized