Effects of multiple laser shock processing (LSP) impacts on mechanical properties and wear behaviors of AISI 8620 steel

The aim of this paper was to address the effects of multiple laser shock processing (LSP) impacts with different pulse energy on mechanical properties and wear behaviors of AISI 8620 steel. Wear analyses were conducted by means of calculation of volume loss and scanning electron microscope (SEM) of the wear surface. Surface profiles, roughness and micro-hardness were measured. The micro-structures in the surface layer of the untreated and LSPed samples (treated by multiple LSP impacts) were investigated by using transmission electron microscopy (TEM) observations. Experimental results and analyses indicated that multiple LSP impacts can remarkably improve the wear resistance of AISI 8620 steel, and the wear mechanism of multiple LSP impacts on AISI 8620 steel was also entirely revealed. The wear process of the unpolished sample subjected to multiple LSP impacts can be described as follows: the wear rate was big at the beginning of sliding dry wear, but then decreased after the micro-indention in the sample surface was polished to the disappear. This phenomenon can be attributed to the fact that multiple LSP impacts generate many micro-indents in the sample surface.

The biomedical application of Ti after severe plastic deformation and thermal oxidation, especially the friction and wear properties of Ti

Surface mechanical attrition treatment (SMAT), a novel surface severe plastic deformation method, was carried out for titanium (Ti) to create a gradient-structured Ti (SMAT Ti). The tribological behaviour was studied under different loads and dry sliding conditions. The results showed that the deformation layer of SMAT Ti was about 160 lm. The friction and wear results showed that the wear resistance of SMAT Ti was enhanced compared to the coarse-grained (CG) counterpart. SMAT Ti showed abrasive wear under 1 and 5 N, and exhibited abrasive and adhesive wear under 2 N. While CG Ti showed abrasive and adhesive wear under 1–2 N, and exhibited abrasive wear under 5 N for the work hardening effects.

Understanding wear conditions during hot stamping

Wear and galling are significant issues during production hot stamping processes. This paper uses thermo-mechanical finite element analysis to study the contact pressure, sliding distance and temperature conditions that occur at the wearing interface during hot stamping. Several hot stamping processes are studied, representing the numerous methods that are used in industry to form a typical hat-shaped channel component. These process include crash forming (without blankholder), stamping with a blank holder with an applied blank holder pressure, and stamping with a clearance blank holder (i.e. with spacer blocks). This paper identifies the distinct contact pressure and temperature conditions that occur for each of these forming methods. The regions of the most severe contact conditions are notably different for each of the forming methods. The work from this paper will form the basis for the development of suitable temperature dependent wear models and low cost wear tests for industrial hot stamping applications.

Slurry pump side-liner wear : comparison of some laboratory and field results

The current work compares some slurry pump lab wear results with the wear found across different field applications with d₈₅ particle size ranging from 100 to 4000mm. Side-liner wear life data has been collected for two different impeller geometries and two different material classes (cast iron and natural rubber). Different field wear patterns have been photographed and categorised on the basis of particle size. The field wear patterns showed close similarity to the lab wear patterns particularly in the areas of localised gouging. Wear rates are also compared for the different geometries. Overall trend of wear with particle size for the white iron parts was similar to the grey iron lab tests albeit at significantly lower wear rates. In general, the wear with the rubber side-liner was less at smaller particle sizes but greater for particles larger than d8The current work compares some slurry pump lab wear results with the wear found across different field applications with d₈₅ particle 10 size ranging from 100 to 4000mm. Side-liner wear life data has been collected for two different impeller geometries and two different 11 material classes (cast iron and natural rubber). Different field wear patterns have been photographed and categorised on the basis of particle 12 size. The field wear patterns showed close similarity to the lab wear patterns particularly in the areas of localised gouging. Wear rates are 13 also compared for the different geometries. Overall trend of wear with particle size for the white iron parts was similar to the grey iron lab 14 tests albeit at significantly lower wear rates. In general, the wear with the rubber side-liner was less at smaller particle sizes but greater for 15 particles larger than d₈₅ of about 700mm. © 2001 Elsevier Science B.Y. All rights reserved.

Interaction between the coating characteristics of galvanneal steel and forming parameters during flat die drawing

Galvanneal steel is considered to be better for automotive applications than its counterpart, galvanized steel, mainly because of its superior coating and surface properties. Galvanneal steel is produced by hot dipping sheet steel in a bath of molten zinc with small, controlled, levels of aluminium, followed by annealing which creates a Fe-Zn intermetallic layer. This intermetallic layer of the coating improves spot weldability and improves subsequent paint appearance. However, if the microstructure of the coating is not properly controlled and forming parameters are not properly selected, wear of the coating could occur during stamping. Frictional sliding of the sheet between the tool surfaces results in considerable amount of coating loss. An Interstitial Free steel with a Galvanneal coating of nominally 60g/m2 was used for the laboratory experiments. Flat Face Friction (FFF) tests were performed with different forming conditions and lubricants to simulate the frictional sliding in stamping. Glow-Discharge Optical Emission Spectrometry (DG-OES) was used to measure the change in the coating thickness during sliding. Optical microscopy was considered for imaging the surfaces as well as an optical method to compare the changes in the coating thickness during the forming. The change to the Galvanneal coating thickness was found to be a function of forming parameters.

Theoretical investigation of wear-resistance mechanism of superelastic shape memory alloy NiTi

Recent experimental research indicates that superelastic shape memory alloy nickel–titanium (NiTi) is superior to stainless steel against wear and could be applied in tribological engineering. It is believed that the super wear resistance of shape memory alloys is mainly due to the recovery of the superelastic deformation. Our recent wear study indicates that wear rate is very sensitive to the maximum contact pressure. In the present investigation, which involves applying Hertz contact theory and the finite element method, the wear behaviour of shape memory alloys is examined against that of stainless steels through analyzing the maximum contact pressure and the plastic deformation. Our investigation indicates that the contribution of superelasticity to the high wear resistance of NiTi is directly linked to the low transformation stress and the large recoverable transformation strain. Furthermore, the low Young's modulus of this alloy also plays an important role to reduce the maximum contact pressure and therefore reduce the wear rate. Additionally, the high plastic yield strength of transformed martensite NiTi enhances its wear resistance further.

Contact pressure and wear in sheet metal forming - an FEM analysis

Wear is the principal cause of tool failure in most sheet metal forming processes. It is well known that the contact pressure between the blank and the tool has a large influence on the wear of the tool, and hence the tool life. This investigation utilises the finite element method to analyse the contact pressure distribution over the die radius for a particular deep drawing process. Furthermore, the evolution of the predicted contact pressure distribution throughout the entire stroke of the punch is also examined. It was found that the majority of the process shows a steady state pressure distribution, with two characteristic peaks over the die radius, at the beginning and end of the sheet contact area. Interestingly, the initial transient contact pressure response showed extremely high localised peak pressures; more than twice that of the steady state peaks. Results are compared to wear reported in the literature, during similar experimental deep drawing processes. Finally, the significance and effect of the results on wear and wear-testing techniques are discussed.

Dynamic output feedback sliding-mode control using pole placement and linear functional observers

This paper presents a methodological approach to design dynamic output feedback sliding-mode control for a class of uncertain dynamical systems. The control action consists of the equivalent control and robust control components. The design of the equivalent control and the sliding function are based on the pole-placement technique. Linear functional observers are developed to implement the sliding function and the equivalent control. Stability of the resulting system under the proposed control scheme is guaranteed. A numerical example is given to demonstrate its efficacy.

Simulation of contact pressure in sheet metal trimming/blanking process

In the car body stamping process, trim/blank die cutting edges are subjected to very high tribological loads that result in loss of tool material from both the punch and die cutting edges. According to Archard’s wear model, normal contact force and sliding distance directly affects the wear. Therefore, knowledge of the acting forces on local contact areas has a pivotal role towards the prediction of tool wear. This paper presents a finite element modelling approach to determining the contact pressure distribution on the tool cutting edges during a trimming/blanking process. Characteristic areas on sheared edge profile, variation of punch force and high contact pressures affected areas have also been analysed.

Contact pressure evolution and its relation to wear in sheet metal forming

For a given sheet metal forming process, an accurate determination of the contact pressure distribution is an essential step towards the estimation of tool life. This investigation utilizes finite element (FE) analysis to model and explain the evolution and distribution of contact pressure over the die radius, throughout the duration of a channel forming process. It was found that a typical two-peak steady-state contact pressure response exists for the majority of the process. However, this was preceded by an initial transient response, characterized by extremely large and localized contact pressures, which were more than double the magnitude of the steady-state peak pressure. The validity of the predicted contact pressure behavior was assessed via detailed numerical analysis and by examining the wear response of an experimental stamping operation. The experimental results revealed that the high contact pressure zones of the transient response corresponded to a severe galling wear mechanism. Therefore, the transient response may be of primary significance to the tool wear response; thus questioning the applicability of traditional bending-under-tension wear tests for sheet metal stamping processes. Finally, a parametric study was conducted, examining the influence of the major process parameters on the steady-state and peak transient contact pressures, using the developed FE model. It was found that the bend ratio and the blank material ultimate tensile strength had the most influence on the peak contact pressures. The main process-related parameters, friction coefficient and blank holder force, were found to have only a minor influence.

Tensile deformation of a ultrafine-grained aluminium alloy: micro shear banding and grain boundary sliding

This work investigates the relationship between the strain rate and the ductility and the underlying deformation mechanisms in an ultrafine-grained Al6082 alloy. At room temperature the uniform elongation of the material exhibits a marked increase with decreasing strain rate. This effect is related to the activation of micro shear banding, which is controlled by grain boundary sliding. The contribution of these mechanisms to uniform elongation is estimated. It is proposed that the grain boundary sliding suppresses the transformation of micro shear bands into macro shear bands. The activity of other deformation mechanisms during plastic deformation of the ultrafine-grained material is also discussed.

Comments on "Adaptive multiple-surface sliding control for non-autonomous systems with mismatched uncertainties"

This note points out that the time complexity of the main multiple-surface sliding control (MSSC) algorithm in Huang and Chen [Huang, A. C. & Chen, Y. C. (2004). Adaptive multiple-surface sliding control for non-autonomous systems with mismatched uncertainties. Automatica, 40(11), 1939-1945] is O(2^n). Here, we propose a simplified recursive design MSSC algorithm with time complexity O(n), and, using mathematical induction, we show that this algorithm agrees with this MSSC law.

Integral terminal sliding mode cooperative control of multi-robot networks

This paper studies the integral terminal sliding mode cooperative control of multi-robot networks. Here, we first propose an integral terminal sliding mode surface for a class of first order systems. Then, we prove that finite time consensus tracking of multi-robot networks can be achieved on this integral terminal sliding mode surface. Simulation results are presented to validate the analysis.

Wear attributes of cashmere single jersey knitted fabrics blended with high and low crimp superfine merino wool

In a replicated experiment, we investigated the impact of cashmere in blends with superfine wools on the wear attributes of single jersey knitted fabrics. We also investigated the relative performance of low crimp/low fiber curvature superfine wool when compared with cashmere and also when compared with traditional high crimp/high fiber curvature superfine wool in pure and blended knitted fabrics. Wool type, blend ratio and fabric structure affected fabric air permeability, resistance to pilling and change in appearance, relaxation shrinkage, hygral expansion, and dimensional stability during laundering. The responses to variation in fiber crimp were much greater than previously reported. The fabric properties of low crimp wool differed significantly from those made from high crimp wool, and low crimp wool fabric properties differed significantly from, but were closer to, the fabric properties of cashmere, compared with high curvature wool.