Influence of silvicultural regime on wood structure characteristics and mechanical properties of clear wood in Pinus sylvestris

Abstract

Monolithic zirconium dioxide as a full contour restorative material: With special emphasis on the optical and mechanical properties

Full contour monolithic zirconia restorations have shown an increased popularity in the dental field over the recent years, owing to its mechanical and acceptable optical properties. However, many features of the restoration are yet to be researched and supported by clinical studies to confirm its place among the other indirect restorative materials This series of in vitro studies aimed at evaluating and comparing the optical and mechanical properties, light cure irradiance, and cement polymerization of multiple monolithic zirconia material at variable thicknesses, environments, treatments, and stabilization. Five different monolithic zirconia materials, four of which were partially stabilized and one fully stabilized were investigated. The optical properties in terms of surface gloss, translucency parameter, and contrast ratio were determined via a reflection spectrophotometer at variable thicknesses, coloring, sintering method, and after immersion in an acidic environment. Light cure irradiance and radiant exposure were quantified through the specimens at variable thicknesses and the degree of conversion of two dual-cure cements was determined via Fourier Transform Infrared spectroscopy. Bi-axial flexural strength was evaluated to compare between the partially and fully stabilized zirconia prepared using different coloring and sintering methods. Surface characterization was performed using a scanning electron microscope and a spinning disk confocal microscope. The surface gloss and translucency of the zirconia investigated were brand and thickness dependent with the translucency values decreasing as the thickness increased. Staining decreased the translucency of the zirconia and enhanced surface gloss as well as the flexural strength of the fully stabilized zirconia but had no effect on partially stabilized zirconia. Immersion in a corrosive acid increased surface gloss and decreased the translucency of some zirconia brands. Zirconia thickness was inversely related to the amount of light irradiance, radiant exposure, and degree of monomer conversion. Type of sintering furnace had no effect on the optical and mechanical properties of zirconia. Monolithic zirconia maybe classified as a semi-translucent material that is well influenced by the thickness, limiting its use in the esthetic zones. Conventional acid-base reaction, autopolymerizing and dual-cure cements are recommended for its cementation. Its desirable mechanical properties give it a high potential as a restoration for posterior teeth. However, close monitoring with controlled clinical studies must be determined before any definite clinical recommendations can be drawn.

Electrical and dielectric properties of uncoated and coated wood-free paper for electrophotography

The print substrate influences the print result in dry toner electrophotography, which is a widely used digital printing method. The influence of the substrate can be seen more easily in color printing, as that is a more complex process compared to monochrome printing. However, the print quality is also affected by the print substrate in grayscale printing. It is thus in the interests of both substrate producers and printing equipment manufacturers to understand the substrate properties that influence the quality of printed images in more detail. In dry toner electrophotography, the image is printed by transferring charged toner particles to the print substrate in the toner transfer nip, utilizing an electric field, in addition to the forces linked to the contact between toner particles and substrate in the nip. The toner transfer and the resulting image quality are thus influenced by the surface texture and the electrical and dielectric properties of the print substrate. In the investigation of the electrical and dielectric properties of the papers and the effects of substrate roughness, in addition to commercial papers, controlled sample sets were made on pilot paper machines and coating machines to exclude uncontrolled variables from the experiments. The electrical and dielectric properties of the papers investigated were electrical resistivity and conductivity, charge acceptance, charge decay, and the dielectric permittivity and losses at different frequencies, including the effect of temperature. The objective was to gain an understanding of how the electrical and dielectric properties are affected by normal variables in papermaking, including basis weight, material density, filler content, ion and moisture contents, and coating. In addition, the dependency of substrate resistivity on the electric field applied was investigated. Local discharging did not inhibit transfer with the paper roughness levels that are normal in electrophotographic color printing. The potential decay of paper revealed that the charge decay cannot be accurately described with a single exponential function, since in charge decay there are overlapping mechanisms of conduction and depolarization of paper. The resistivity of the paper depends on the NaCl content and exponentially on moisture content although it is also strongly dependent on the electric field applied. This dependency is influenced by the thickness, density, and filler contents of the paper. Furthermore, the Poole-Frenkel model can be applied to the resistivity of uncoated paper. The real part of the dielectric constant ε’ increases with NaCl content and relative humidity, but when these materials cannot polarize freely, the increase cannot be explained by summing the effects of their dielectric constants. Dependencies between the dielectric constant and dielectric loss factor and NaCl content, temperature, and frequency show that in the presence of a sufficient amount of moisture and NaCl, new structures with a relaxation time of the order of 10-3 s are formed in paper. The ε’ of coated papers is influenced by the addition of pigments and other coating additives with polarizable groups and due to the increase in density. The charging potential decreases and the electrical conductivity, potential decay rate, and dielectric constant of paper increase with increasing temperature. The dependencies are exponential and the temperature dependencies and their activation energies are altered by the ion content. The results have been utilized in manufacturing substrates for electrophotographic color printing.

Aktiivinen melunvaimennus ampumaradalla

Aktiivinen melunvaimennus (active noise control, ANC) onkauan tunnettu ja sovellettu tekniikka. Kuitenkaan sitä ei ole aiemmin sovellettu impulssimaiseen satunnaiseen meluun. Tässä diplomityössä tutkitaan aktiivisenmelunvaimennuksen soveltuvuutta ampumaradan melunvaimennukseen. Ampumarata äärimmäisenä tapauksena asettaa korkean vaatimustason laitteistolle ja sen komponenteille. Suurin haaste on etsiä sopivat laitteiston komponentit, jotka tuottavat ja kestävät suurta äänenpainetasoa. Myös muuttuvat sääolosuhteet asettavat vaatimuksensa laitteiden mekaaniselle kestävyydelle sekä säänkestävyydelle. Työssä paneuduttiin erityisesti selvittämään, mitä kaupallisesti saatavilla olevia komponentteja voidaan hyödyntää aktiiviseen impulssimelunvaimennusjärjestelmään. Kaupallisten komponenttien soveltuvuutta aktiiviseen impulssimelunvaimennukseen analysoitiin laboratorio- ja kenttämittauksin. Työssä esitetään myös tulokset yksinkertaisella koelaitteistolla saavutetusta vaimennuksesta kenttäolosuhteissa.

Sähköisen komponenttikirjaston kehittäminen suurnostureiden mekaanista suunnittelua varten

Suurten satama- ja telakkanostureiden suunnittelussa käytetään suuret määrät valmiita komponentteja. Komponentteja ovat sähköiset ja mekaaniset komponentit. Näiden lisäksi komponenteiksi voidaan käsittää myös teräsrakenteet. Tässä diplomityössä on tehty ostettavista mekaanisista ostokomponenteista sähköinen komponenttikirjasto. Mekaanisia komponentteja ovat esimerkiksi mekaaniset liitososat ja mekaaniset voiman siirtoelimet. Kirjaston tehtävänä on helpottaa ja nopeuttaa suunnittelutyötä. Helpottaen tiedon hakua ja vähentää siihen kuluvaa aikaa. Oleellinen osa tietokantaa ovat käyttöliittymät, joilla tietokannan useiden taulukoiden tiedot esitetään. Näyttöjen suunnitteluun ja ulkoasun muotoiluun on panostettu käytettävyyden ja yksinkertaisuuden parantamiseksi. Tietokanta sisältää myös valmiita raporttipohjia komponenttitietojen tulostamista varten.

Teholähdesuunnittelu

Työssä vertaillaan massatuotannon näkökulmasta eri tehoalueille sopivia teholähteen toteuttamisvaihtoehtoja. Lisäksi esitellään standardien asettamia vaatimuksia teholähteille. Työssä käsitellään teholähdesuunnittelun eri osa-alueita ja niihin sopivien simulointityökalujen hyödyntämismahdollisuuksia suunnitteluprosessin osana. Simulointituloksia ja teoreettisia laskelmia vertaillaan prototyypistä suoritettuihin mittauksiin.

Kestomagneettigeneraattorin lämmönsiirron mallinnus tuulivoimakäytössä

Pyörivien sähkökoneiden suunnittelussa terminen suunnittelu on yhtä tärkeää kuin sähköinen ja mekaaninen suunnittelukin. Tässä diplomityössä tarkoituksena on kehittää ilmajäähdytteisten kestomagneettigeneraattorien laskentaan soveltuva lämmönsiirtymismalli, jolla staattorin lämpötilajakauma voitaisiin selvittää. Kehitetty lämmönsiirtymismalli perustuu kolmiulotteiseen äärellisen erotuksen (finite difference) menetelmään. Malli ottaa huomioon lämmönjohtumisen staattorin aktiiviosissa ja konvektion jäähdytysilmavirtaan. Mallissa on myös yksinkertainen painehäviölaskenta jäähdytysjärjestelmän komponenttien mitoittamista varten. Laskentamallilla lasketaan esimerkkitapauksena 4,3 MW:n kestomagneettigeneraattorin jäähdytystä eri toimintapisteissä. Tuloksia verrataan CFD-mallinnuksen antamiin tuloksiin sekä kokeellisten mittausten antamiin tuloksiin.

Tuulivoimalan staattoripakan puristusrakenteen kehittäminen

Diplomityössä tutkittiin voidaanko tuulivoimalan generaattorin staattoripakan puristamisessa hyödyntää komposiittista rakenneratkaisua. Tyypillisesti generaattorissa staattorin teräslevyt puristetaan erilaisilla teräsrakenteilla toisiaan vasten. Tavoitteena oli selvittää, voidaanko puristavan komposiittirakenteen osana hyödyntää liimaliitosta tai laminoitua liitosta. Tarkoitus oli etsiä rakenteeseen soveltuva liima ja liimaliitoksen arvot tai laminoitu rakenne ja sille soveltuvat materiaalit ja suoritustapa. Työssä on perehdytty erilaisiin tuulivoimalatyyppeihin, sekä niissä käytettäviin kesto- ja vierasmagnetoituihin generaattorityyppeihin. Tämän lisäksi on tarkasteltu niissä käytettävien staattorien valmistusvaihtoehtoja ja syitä miksi niissä olevat teräslevyt on puristettava toisiaan vasten. Samalla on luotu katsaus nykyisin käytössä oleviin rakenteisiin, joilla puristus voidaan toteuttaa. Liimauksesta on käsitelty perusteoriaa, sekä seikkoja jotka vaikuttavat liimaliitoksen kestoon. Työssä tutkittavaan liitokseen soveltuvien liimojen ominaisuuksia on käsitelty. Myös laminoituun liitokseen jo aiemmin kovettuneeseen komposiittiin on perehdytty. Tutkittavaan rakenteeseen soveltuvia hartsi- ja lasikuitutyyppejä on esitelty. Komposiittien mekaaniseen liittämiseen on lyhyesti perehdytty. Työssä suoritettiin useita vetokokeita, joilla selvitettiin puristusrakenteen tutkimista varten valmistettujen koekappaleiden suurin vetokuormankesto. Vetokokeiden perusteella voitiin valita soveltuvin rakenne staattorin puristamiseksi.

Design of Pulsed Electroacoustic Measurement System for Space Charge Characterisation

Pulsed electroacoustic (PEA) method is a commonly used non-destructive technique for investigating space charges. It has been developed since early 1980s. These days there is continuing interest for better understanding of the influence of space charge on the reliability of solid electrical insulation under high electric field. The PEA method is widely used for space charge profiling for its robust and relatively inexpensive features. The PEA technique relies on a voltage impulse used to temporarily disturb the space charge equilibrium in a dielectric. The acoustic wave is generated by charge movement in the sample and detected by means of a piezoelectric film. The spatial distribution of the space charge is contained within the detected signal. The principle of such a system is already well established, and several kinds of setups have been constructed for different measurement needs. This thesis presents the design of a PEA measurement system as a systems engineering project. The operating principle and some recent developments are summarised. The steps of electrical and mechanical design of the instrument are discussed. A common procedure for measuring space charges is explained and applied to verify the functionality of the system. The measurement system is provided as an additional basic research tool for the Corporate Research Centre of ABB (China) Ltd. It can be used to characterise flat samples with thickness of 0.2–0.5 mm under DC stress. The spatial resolution of the measurement is 20 μm.

Computational modeling of stented coronary arteries

The application of computational fluid dynamics (CFD) and finite element analysis (FEA) has been growing rapidly in the various fields of science and technology. One of the areas of interest is in biomedical engineering. The altered hemodynamics inside the blood vessels plays a key role in the development of the arterial disease called atherosclerosis, which is the major cause of human death worldwide. Atherosclerosis is often treated with the stenting procedure to restore the normal blood flow. A stent is a tubular, flexible structure, usually made of metals, which is driven and expanded in the blocked arteries. Despite the success rate of the stenting procedure, it is often associated with the restenosis (re-narrowing of the artery) process. The presence of non-biological device in the artery causes inflammation or re-growth of atherosclerotic lesions in the treated vessels. Several factors including the design of stents, type of stent expansion, expansion pressure, morphology and composition of vessel wall influence the restenosis process. Therefore, the role of computational studies is crucial in the investigation and optimisation of the factors that influence post-stenting complications. This thesis focuses on the stent-vessel wall interactions followed by the blood flow in the post-stenting stage of stenosed human coronary artery. Hemodynamic and mechanical stresses were analysed in three separate stent-plaque-artery models. Plaque was modeled as a multi-layer (fibrous cap (FC), necrotic core (NC), and fibrosis (F)) and the arterial wall as a single layer domain. CFD/FEA simulations were performed using commercial software packages in several models mimicking the various stages and morphologies of atherosclerosis. The tissue prolapse (TP) of stented vessel wall, the distribution of von Mises stress (VMS) inside various layers of vessel wall, and the wall shear stress (WSS) along the luminal surface of the deformed vessel wall were measured and evaluated. The results revealed the role of the stenosis size, thickness of each layer of atherosclerotic wall, thickness of stent strut, pressure applied for stenosis expansion, and the flow condition in the distribution of stresses. The thicknesses of FC, and NC and the total thickness of plaque are critical in controlling the stresses inside the tissue. A small change in morphology of artery wall can significantly affect the distribution of stresses. In particular, FC is the most sensitive layer to TP and stresses, which could determine plaque’s vulnerability to rupture. The WSS is highly influenced by the deflection of artery, which in turn is dependent on the structural composition of arterial wall layers. Together with the stenosis size, their roles could play a decisive role in controlling the low values of WSS (<0.5 Pa) prone to restenosis. Moreover, the time dependent flow altered the percentage of luminal area with WSS values less than 0.5 Pa at different time instants. The non- Newtonian viscosity model of the blood properties significantly affects the prediction of WSS magnitude. The outcomes of this investigation will help to better understand the roles of the individual layers of atherosclerotic vessels and their risk to provoke restenosis at the post-stenting stage. As a consequence, the implementation of such an approach to assess the post-stented stresses will assist the engineers and clinicians in optimizing the stenting techniques to minimize the occurrence of restenosis.

Development of Measurement Systems in Scientific Research: Case Study

In recent years, technological advancements in microelectronics and sensor technologies have revolutionized the field of electrical engineering. New manufacturing techniques have enabled a higher level of integration that has combined sensors and electronics into compact and inexpensive systems. Previously, the challenge in measurements was to understand the operation of the electronics and sensors, but this has now changed. Nowadays, the challenge in measurement instrumentation lies in mastering the whole system, not just the electronics. To address this issue, this doctoral dissertation studies whether it would be beneficial to consider a measurement system as a whole from the physical phenomena to the digital recording device, where each piece of the measurement system affects the system performance, rather than as a system consisting of small independent parts such as a sensor or an amplifier that could be designed separately. The objective of this doctoral dissertation is to describe in depth the development of the measurement system taking into account the challenges caused by the electrical and mechanical requirements and the measurement environment. The work is done as an empirical case study in two example applications that are both intended for scientific studies. The cases are a light sensitive biological sensor used in imaging and a gas electron multiplier detector for particle physics. The study showed that in these two cases there were a number of different parts of the measurement system that interacted with each other. Without considering these interactions, the reliability of the measurement may be compromised, which may lead to wrong conclusions about the measurement. For this reason it is beneficial to conceptualize the measurement system as a whole from the physical phenomena to the digital recording device where each piece of the measurement system affects the system performance. The results work as examples of how a measurement system can be successfully constructed to support a study of sensors and electronics.