Kokonaisvaltainen suorituskyvyn mittaaminen kunnossapitoyrityksessä

Työn tavoitteena oli kehittää kunnossapitoyritykselle koko toiminnan kattava suorituskyvyn mittausjärjestelmä. Mittaamisen tarkoituksena oli tiivistää eri tietojärjestelmistä saatava informaatio ja tarjota tietoa omistajille yrityksen kokonaissuorituskyvyn kehittymisestä päätöksenteon pohjaksi sekä tyydyttää suurimman asiakkaan tiedontarve tehtaan kunnossapitotoimintojen kehittymisestä. Ensin tutustuttiin suorituskyvyn, sen mittaamisen sekä suorituskykymittariston kehit-tämisen ja käyttöönoton teoriaan. Tämän teorian pohjalta rakennettiin Etelä-Savon Kunnossapito Oy:lle kokonaisvaltainen suorituskykymittaristo. Projektin aluksi määriteltiin ESK Oy:n toiminnan perusasioita ja analysoitiin yrityksen nykytilaa. Tämän perusteella valittiin seurattavat suorituskyvyn osa-alueet ja mittarit. Osa-alueiksi valittiin kunnossapito, projekti- ja tuotantotoiminta, asiakastyytyväisyys, henkilöstö ja talous. Näistä jokaiselle määriteltiin kahdesta viiteen mittaria. Käytännön mittaamiseen hankittiin suorituskykymatriisiin perustuva ohjelmasovellus. Mittaamisen avuksi yksittäisille mittareille luotiin ohjeet käytännön mittaamisen järjestelyistä. Mittariston hyödyt tulevat esille vasta kun mittaustuloksia on kertynyt järjestelmään pidemmältä ajanjaksolta. Näiden säännöllinen analysointi on olennaista, jotta mittariston avulla voidaan seurata kuinka kaukana ollaan asetetuista tavoitteista ja voidaan kohdistaa kehitystoimet alueille, joissa niitä eniten tarvitaan.

Maritime Safety in the Gulf of Finland. Review on Policy Instruments

Suomenlahden lisääntynyt meriliikenne on herättänyt huolta meriliikenteen turvallisuuden tasosta, ja erityisesti Venäjän öljyviennin kasvu on lisännyt öljyonnettomuuden todennäköisyyttä Suomenlahdella. Erilaiset kansainväliset, alueelliset ja kansalliset ohjauskeinot pyrkivät vähentämään merionnettomuuden riskiä ja meriliikenteen muita haittavaikutuksia. Tämä raportti käsittelee meriturvallisuuden yhteiskunnallisia ohjauskeinoja: ohjauskeinoja yleisellä tasolla, meriturvallisuuden keskeisimpiä säätelijöitä, meriturvallisuuden ohjauskeinoja ja meriturvallisuuspolitiikan tulevaisuuden näkymiä, ohjauskeinojen tehokkuutta ja nykyisen meriturvallisuuden ohjausjärjestelmän heikkouksia. Raportti on kirjallisuuskatsaus meriturvallisuuden yhteiskunnalliseen sääntelyn rakenteeseen ja tilaan erityisesti Suomenlahden meriliikenteen näkökulmasta. Raportti on osa tutkimusprojektia ”SAFGOF - Suomenlahden meriliikenteen kasvunäkymät 2007 - 2015 ja kasvun vaikutukset ympäristölle ja kuljetusketjujen toimintaan” ja sen työpakettia 6 ”Keskeisimmät riskit ja yhteiskunnalliset vaikutuskeinot”. Yhteiskunnalliset ohjauskeinot voidaan ryhmitellä hallinnollisiin, taloudellisiin ja tietoohjaukseen perustuviin ohjauskeinoihin. Meriturvallisuuden edistämisessä käytetään kaikkia näitä, mutta hallinnolliset ohjauskeinot ovat tärkeimmässä asemassa. Merenkulun kansainvälisen luonteen vuoksi meriturvallisuuden sääntely tapahtuu pääosin kansainvälisellä tasolla YK:n ja erityisesti Kansainvälisen merenkulkujärjestön (IMO) toimesta. Lisäksi myös Euroopan Unionilla on omaa meriturvallisuuteen liittyvää sääntelyä ja on myös olemassa muita alueellisia meriturvallisuuden edistämiseen liittyviä elimiä kuten HELCOM. Joitakin meriturvallisuuden osa-alueita säädellään myös kansallisella tasolla. Hallinnolliset meriturvallisuuden ohjauskeinot sisältävät aluksen rakenteisiin ja varustukseen, alusten kunnon valvontaan, merimiehiin ja merityön tekemiseen sekä navigointiin liittyviä ohjauskeinoja. Taloudellisiin ohjauskeinoihin kuuluvat esimerkiksi väylä- ja satamamaksut, merivakuutukset, P&I klubit, vastuullisuus- ja korvauskysymykset sekä taloudelliset kannustimet. Taloudellisten ohjauskeinojen käyttö meriturvallisuuden edistämiseen on melko vähäistä verrattuna hallinnollisten ohjauskeinojen käyttöön, mutta niitä voitaisiin varmasti käyttää enemmänkin. Ongelmana taloudellisten ohjauskeinojen käytössä on se, että ne kuuluvat pitkälti kansallisen sääntelyn piiriin, joten alueellisten tai kansainvälisten intressien edistäminen taloudellisilla ohjauskeinoilla voi olla hankalaa. Tieto-ohjaus perustuu toimijoiden vapaaehtoisuuteen ja yleisen tiedotuksen lisäksi tieto-ohjaukseen sisältyy esimerkiksi vapaaehtoinen koulutus, sertifiointi tai meriturvallisuuden edistämiseen tähtäävät palkinnot. Poliittisella tasolla meriliikenteen aiheuttamat turvallisuusriskit Suomenlahdella on otettu vakavasti ja paljon työtä tehdään eri tahoilla riskien minimoimiseksi. Uutta sääntelyä on odotettavissa etenkin liittyen meriliikenteen ympäristövaikutuksiin ja meriliikenteen ohjaukseen kuten meriliikenteen sähköisiin seurantajärjestelmiin. Myös inhimilliseen tekijän merkitykseen meriturvallisuuden kehittämisessä on kiinnitetty lisääntyvissä määrin huomiota, mutta inhimilliseen tekijän osalta tehokkaiden ohjauskeinojen kehittäminen näyttää olevan haasteellista. Yleisimmin lääkkeeksi esitetään koulutuksen kehittämistä. Kirjallisuudessa esitettyjen kriteereiden mukaan tehokkaiden ohjauskeinojen tulisi täyttää seuraavat vaatimukset: 1) tarkoituksenmukaisuus – ohjauskeinojen täytyy olla sopivia asetetun tavoitteen saavuttamiseen, 2) taloudellinen tehokkuus – ohjauskeinon hyödyt vs. kustannukset tulisi olla tasapainossa, 3) hyväksyttävyys – ohjauskeinon täytyy olla hyväksyttävä asianosaisten ja myös laajemman yhteiskunnan näkökulmasta katsottuna, 4) toimeenpano – ohjauskeinon toimeenpanon pitää olla mahdollista ja sen noudattamista täytyy pystyä valvomaan, 5) lateraaliset vaikutukset – hyvällä ohjauskeinolla on positiivisia seurannaisvaikutuksia muutoinkin kuin vain ohjauskeinon ensisijaisten tavoitteiden saavuttaminen, 6) kannustin ja uuden luominen – hyvä ohjauskeino kannustaa kokeilemaan uusia ratkaisuja ja kehittämään toimintaa. Meriturvallisuutta koskevaa sääntelyä on paljon ja yleisesti ottaen merionnettomuuksien lukumäärä on ollut laskeva viime vuosikymmenien aikana. Suuri osa sääntelystä on ollut tehokasta ja parantanut turvallisuuden tasoa maailman merillä. Silti merionnettomuuksia ja muita vaarallisia tapahtumia sattuu edelleen. Nykyistä sääntelyjärjestelmää voidaan kritisoida monen asian suhteen. Kansainvälisen sääntelyn aikaansaaminen ei ole helppoa: prosessi on yleensä hidas ja tuloksena voi olla kompromissien kompromissi. Kansainvälinen sääntely on yleensä reaktiivista eli ongelmakohtiin puututaan vasta kun jokin onnettomuus tapahtuu sen sijaan että se olisi proaktiivista ja pyrkisi puuttumaan ongelmakohtiin jo ennen kuin jotain tapahtuu. IMO:n työskentely perustuu kansallisvaltioiden osallistumiseen ja sääntelyn toimeenpano tapahtuu lippuvaltioiden toimesta. Kansallisvaltiot ajavat IMO:ssa pääasiallisesti omia intressejään ja sääntelyn toimeenpanossa on suuria eroja lippuvaltioiden välillä. IMO:n kyvyttömyys puuttua havaittuihin ongelmiin nopeasti ja ottaa sääntelyssä huomioon paikallisia olosuhteita on johtanut siihen, että esimerkiksi Euroopan Unioni on alkanut itse säädellä meriturvallisuutta ja että on olemassa sellaisia alueellisia erityisjärjestelyjä kuin PSSA (particularly sensitive sea area – erityisen herkkä merialue). Merenkulkualalla toimii monenlaisia yrityksiä: toisaalta yrityksiä, jotka pyrkivät toimimaan turvallisesti ja kehittämään turvallisuutta vielä korkeammalle tasolle, ja toisaalta yrityksiä, jotka toimivat niin halvalla kuin mahdollista, eivät välitä turvallisuusseikoista, ja joilla usein on monimutkaiset ja epämääräiset omistusolosuhteet ja joita vahingon sattuessa on vaikea saada vastuuseen. Ongelma on, että kansainvälisellä merenkulkualalla kaikkien yritysten on toimittava samoilla markkinoilla. Vastuuttomien yritysten toiminnan mahdollistavat laivaajat ja muut alan toimijat, jotka suostuvat tekemään yhteistyötä niiden kanssa. Välinpitämätön suhtautuminen turvallisuuteen johtuu osaksi myös merenkulun vanhoillisesta turvallisuuskulttuurista. Verrattaessa meriturvallisuuden sääntelyjärjestelmää kokonaisuutena tehokkaiden ohjauskeinoihin kriteereihin, voidaan todeta, että monien kriteerien osalta nykyistä järjestelmää voidaan pitää tehokkaana ja onnistuneena. Suurimmat ongelmat lienevät sääntelyn toimeenpanossa ja ohjauskeinojen kustannustehokkuudessa. Lippuvaltioiden toimeenpanoon perustuva järjestelmä ei toimi toivotulla tavalla, josta mukavuuslippujen olemassa olo on selvin merkki. Ohjauskeinojen, sekä yksittäisten ohjauskeinojen että vertailtaessa eri ohjauskeinoja keskenään, kustannustehokkuutta on usein vaikea arvioida, minkä seurauksena ohjauskeinojen kustannustehokkuudesta ei ole saatavissa luotettavaa tietoa ja tuloksena voi olla, että ohjauskeino on käytännössä pienen riskin eliminoimista korkealla kustannuksella. Kansainvälisen tason meriturvallisuus- (ja merenkulku-) politiikan menettelytavoiksi on ehdotettu myös muita vaihtoehtoja kuin nykyinen järjestelmä, esimerkiksi monitasoista tai polysentristä hallintojärjestelmää. Monitasoisella hallintojärjestelmällä tarkoitetaan järjestelmää, jossa keskushallinto on hajautettu sekä vertikaalisesti alueellisille tasoille että horisontaalisesti ei-valtiollisille toimijoille. Polysentrinen hallintojärjestelmä menee vielä askeleen pidemmälle. Polysentrinen hallintojärjestelmä on hallintotapa, jonka puitteissa kaikentyyppiset toimijat, sekä yksityiset että julkiset, voivat osallistua hallintoon, siis esimerkiksi hallitukset, edunvalvontajärjestöt, kaupalliset yritykset jne. Kansainvälinen lainsäädäntö määrittelee yleiset tasot, mutta konkreettiset toimenpiteet voidaan päättää paikallisella tasolla eri toimijoiden välisessä yhteistyössä. Tämän tyyppisissä hallintojärjestelmissä merenkulkualan todellinen, kansainvälinen mutta toisaalta paikallinen, toimintaympäristö tulisi otetuksi paremmin huomioon kuin järjestelmässä, joka perustuu kansallisvaltioiden keskenään yhteistyössä tekemään sääntelyyn. Tällainen muutos meriturvallisuuden hallinnassa vaatisi kuitenkin suurta periaatteellista suunnanmuutosta, jollaisen toteutumista ei voi pitää kovin todennäköisenä ainakaan lyhyellä tähtäimellä.

Formal development and quantitative verification of dependable systems

-

Helsinki hub – new traffic flows and business networks

This thesis is the Logistics Development Forum's assignment and the work dealing with the development of the Port of Helsinki as part of Helsinki hub. The Forum aims to develop logistics efficiency through public-private co-operation and development of the port is clearly dependent on both factors. Freight volumes in the Port of Helsinki are the biggest single factor in hub and, therefore, the role of the port of the entire hub development is strong. The aim is to look at how the port will develop as a result of changes in the foreign trade of Finland and the Northern European logistics trends in 25 years time period. Work includes the current state analysis and scenario work. The analyses are intended to find out, which trends are the most important in the port volume development. The change and effect of trends is examined through scenarios based on current state. Based on the work, the structure of Finnish export industry and international demand are in the key role in the port volume development. There is significant difference between demands of Finnish exporting products in different export markets and the development between the markets has different impacts on the port volumes by mass and cargo type. On the other hand, the Finnish economy is stuck in a prolonged recession and competition between ports has become a significant factor in the individual port's volume development. Ecological valuesand regulations have changed the competitive landscape and maritime transport emissions reductions has become an important competitive factor for short routes in the Baltic Sea, such as in the link between Helsinki and Tallinn.

Investigation ofsolid - state cooler based on electrocaloric effect

Electrocaloric cooling based on ability of material to change temperature by applying an electric field under adiabatic conditions is relatively new and challenging direction of ferroelectrics research. In this work we report about analytical, simulation and experimental data for BaSrTiO3 thin film and bulk ceramic samples. Detailed discussion of a theoretical base of the electrocaloric effect is included. Demonstrated experimental and computational results exemplify rational approach to a problem of solid-state cooler construction.

Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

Quasiclassical Approach to the Vortex State in Iron-based Superconductors

The quasiclassical approach was applied to the investigation of the vortex properties in the ironbased superconductors. The special attention was paid to manifestation of the nonlocal effects of the vortex core structure. The main results are as follows: (i) The effects of the pairing symmetries (s+ and s₊₊) on the cutoff parameter of field distribution, ξh, in stoichiometric (like LiFeAs) and nonstoichiometric (like doped BaFe₂As₂) iron pnictides have been investigated using Eilenberger quasiclassical equations. Magnetic field, temperature and impurity scattering dependences of ξh have been calculated. Two opposite behavior have been discovered. The ξh /ξc2 ratio is less in s+ symmetry when intraband impurity scattering (Γ₀) is much larger than one and much larger than interband impurity scattering (Γπ), i.e. in nonstoichiometric iron pnictides. Opposite, the value ξh /ξc2 is higher in s+ case and the field dependent curve is shifted upward from the "clean" case (Γ₀ = Γπ = 0) for stoichiometric iron pnictides (Γ₀ = Γπ ≪ 1). (ii) Eilenberger approach to the cutoff parameter, ξh, of the field distribution in the mixed state of high

Emotions in a Web-based Learning Environment

The aim of this thesis was to examine emotions in a web-based learning environment (WBLE). Theoretically, the thesis was grounded on the dimensional model of emotions. Four empirical studies were conducted. Study I focused on students’ anxiety and their self-efficacy in computer-using situations. Studies II and III examined the influence of experienced emotions on students’ collaborative visible and non-collaborative invisible activities and lurking in a WBLE. Study II also focused on the antecedents of the emotions students experience in a web-based learning environment. Study IV concentrated on clarifying the differences between emotions experienced in face-to-face and web-based collaborative learning. The results of these studies are reported in four original research articles published in scientific journals. The present studies demonstrate that emotions are important determinants of student behaviour in a web-based learning, and justify the conclusion that interactions on the web can and do have an emotional content. Based on the results of these empirical studies, it can be concluded that the emotions students experience during the web-based learning result mostly from the social interactions rather than from the technological context. The studies indicate that the technology itself is not the only antecedent of students’ emotional reactions in the collaborative web-based learning situations. However, the technology itself also exerted an influence on students’ behaviour. It was found that students’ computer anxiety was associated with their negative expectations of the consequences of using technology-based learning environments in their studies. Moreover, the results also indicated that student behaviours in a WBLE can be divided into three partially overlapping classes: i) collaborative visible ii) non-collaborative invisible activities, and iii) lurking. What is more, students’ emotions experienced during the web-based learning affected how actively they participated in such activities in the environment. Especially lurkers, i.e. students who seldom participated in discussions but frequently visited the online environment, experienced more negatively valenced emotions during the courses than did the other students. This result indicates that such negatively toned emotional experiences can make the lurking individuals less eager to participate in other WBLE courses in the future. Therefore, future research should also focus more precisely on the reasons that cause individuals to lurk in online learning groups, and the development of learning tasks that do not encourage or permit lurking or inactivity. Finally, the results from the study comparing emotional reactions in web-based and face-to-face collaborative learning indicated that the learning by means of web-based communication resulted in more affective reactivity when compared to learning in a face-to-face situation. The results imply that the students in the web-based learning group experienced more intense emotions than the students in the face-to-face learning group.The interpretations of this result are that the lack of means for expressing emotional reactions and perceiving others’ emotions increased the affectivity in the web-based learning groups. Such increased affective reactivity could, for example, debilitate individual’s learning performance, especially in complex learning tasks. Therefore, it is recommended that in the future more studies should be focused on the possibilities to express emotions in a text-based web environment to ensure better means for communicating emotions, and subsequently, possibly decrease the high level of affectivity. However, we do not yet know whether the use of means for communicating emotional expressions via the web (for example, “smileys” or “emoticons”) would be beneficial or disadvantageous in formal learning situations. Therefore, future studies should also focus on assessing how the use of such symbols as a means for expressing emotions in a text-based web environment would affect students’ and teachers’ behaviour and emotional state in web-based learning environments.

Studies on integrating kinematic design method with mechanical systems simulation techniques

Theultimate goal of any research in the mechanism/kinematic/design area may be called predictive design, ie the optimisation of mechanism proportions in the design stage without requiring extensive life and wear testing. This is an ambitious goal and can be realised through development and refinement of numerical (computational) technology in order to facilitate the design analysis and optimisation of complex mechanisms, mechanical components and systems. As a part of the systematic design methodology this thesis concentrates on kinematic synthesis (kinematic design and analysis) methods in the mechanism synthesis process. The main task of kinematic design is to find all possible solutions in the form of structural parameters to accomplish the desired requirements of motion. Main formulations of kinematic design can be broadly divided to exact synthesis and approximate synthesis formulations. The exact synthesis formulation is based in solving n linear or nonlinear equations in n variables and the solutions for the problem areget by adopting closed form classical or modern algebraic solution methods or using numerical solution methods based on the polynomial continuation or homotopy. The approximate synthesis formulations is based on minimising the approximation error by direct optimisation The main drawbacks of exact synthesis formulationare: (ia) limitations of number of design specifications and (iia) failure in handling design constraints- especially inequality constraints. The main drawbacks of approximate synthesis formulations are: (ib) it is difficult to choose a proper initial linkage and (iib) it is hard to find more than one solution. Recentformulations in solving the approximate synthesis problem adopts polynomial continuation providing several solutions, but it can not handle inequality const-raints. Based on the practical design needs the mixed exact-approximate position synthesis with two exact and an unlimited number of approximate positions has also been developed. The solutions space is presented as a ground pivot map but thepole between the exact positions cannot be selected as a ground pivot. In this thesis the exact synthesis problem of planar mechanism is solved by generating all possible solutions for the optimisation process ¿ including solutions in positive dimensional solution sets - within inequality constraints of structural parameters. Through the literature research it is first shown that the algebraic and numerical solution methods ¿ used in the research area of computational kinematics ¿ are capable of solving non-parametric algebraic systems of n equations inn variables and cannot handle the singularities associated with positive-dimensional solution sets. In this thesis the problem of positive-dimensional solutionsets is solved adopting the main principles from mathematical research area of algebraic geometry in solving parametric ( in the mathematical sense that all parameter values are considered ¿ including the degenerate cases ¿ for which the system is solvable ) algebraic systems of n equations and at least n+1 variables.Adopting the developed solution method in solving the dyadic equations in direct polynomial form in two- to three-precision-points it has been algebraically proved and numerically demonstrated that the map of the ground pivots is ambiguousand that the singularities associated with positive-dimensional solution sets can be solved. The positive-dimensional solution sets associated with the poles might contain physically meaningful solutions in the form of optimal defectfree mechanisms. Traditionally the mechanism optimisation of hydraulically driven boommechanisms is done at early state of the design process. This will result in optimal component design rather than optimal system level design. Modern mechanismoptimisation at system level demands integration of kinematic design methods with mechanical system simulation techniques. In this thesis a new kinematic design method for hydraulically driven boom mechanism is developed and integrated in mechanical system simulation techniques. The developed kinematic design method is based on the combinations of two-precision-point formulation and on optimisation ( with mathematical programming techniques or adopting optimisation methods based on probability and statistics ) of substructures using calculated criteria from the system level response of multidegree-of-freedom mechanisms. Eg. by adopting the mixed exact-approximate position synthesis in direct optimisation (using mathematical programming techniques) with two exact positions and an unlimitednumber of approximate positions the drawbacks of (ia)-(iib) has been cancelled.The design principles of the developed method are based on the design-tree -approach of the mechanical systems and the design method ¿ in principle ¿ is capable of capturing the interrelationship between kinematic and dynamic synthesis simultaneously when the developed kinematic design method is integrated with the mechanical system simulation techniques.

The design and implementation of a standards-based mobile messaging platform - case WAP Push Proxy Gateway

Tässä diplomityössä perehdytään WAP:in Push -viitekehykseen. WAP-standardit määrittelevät kuinka Internet-tyyppisiä palveluita, joita voidaan käyttää erilaisia mobiileja päätelaiteitteita käyttäen, toteutetaan tehokkaalla ja verkkoteknologiasta riippumattomalla tavalla. WAP pohjautuu Internet:iin, mutta huomioi pienten päätelaitteiden ja mobiiliverkkojen rajoitukset ja erikoisominaisuudet. WAP Push viitekehys määrittelee verkon aloittaman palvelusisällön toimittamisen. Työn teoriaosassa käydään läpi yleinen WAP-arkkitehtuuri ja WAP-protokollapino käyttäen vertailukohtina lanka-Internetin arkkitehtuuria ja protokollapinoa. Edellistä perustana käyttäen tutustaan WAP Push -viitekehykseen. Käytännönosassa kuvataan WAP Push -välityspalvelimen suunnittelu ja kehitystyö. WAP Push -välityspalvelin on keskeinen verkkoelementti WAP Push -viitekehyksessä. WAP Push -välityspalvelin yhdistää Internetin ja mobiiliverkon tavalla, joka piilottaa teknologiaeroavaisuudet Internetissä olevalta palveluntuottajalta.

Subsystem Testing of Message Guided State Machines Using a Simulator Framework

Simulaattorit ovat yksinkertaistettuja malleja tietyistä järjestelmän osioista. Niitä käytetään mallintamaan testattavan osion ympärillä olevien muiden osioiden ulkoista toimintaa, jotta testattavalle osiolle saadaan oikeanlainen toimintaympäristö aikaiseksi. Tilakoneita käytetään mallintamaan ohjelmistojen tai niiden osien toimintaa. Sanomaohjatuissa tilakoneissa tilojen vaihdot perustuvat saapuviin sanomiin. Tässä työssä esitellään erään ohjelmiston alijärjestelmän testaamisessa käytettävä arkkitehtuuri, joka perustuu suurelta osin simulaattoreiden käyttöön muiden alijärjestelmien mallintamisessa. Testattava ohjelmisto koostuu enimmäkseen tilakoneista, jotka vaihtavat keskenään sanomia ja ohjaavat näin toistensa tilasiirtymiä. Työn testausympäristö on suunniteltu juuri tämänkaltaisen ohjelmiston testaamiseen. Työssä esiteltävää testausympäristöä myöskin käytettiin useamman kuukauden ajan ja se todettiin toimivaksi. Joitakin testausympäristön käyttöohjeita, käyttökokemuksia sekä siihen liittyviä parannusehdotuksia käydään läpi työn loppuosassa. Erityisesti havaittiin miten tärkeää on testata implementaatiota jo luokka tasolla ennen alijärjestelmä tason testaukseen siirtymistä sekä päädyttiin siihen, että suunnitteluvaiheen pitäisi olla lähemmin liitoksissa alijärjestelmätestaukseen.

State of Logistics and Operations Management in Finnish and Swedish Companies – Survey Research Findings

In this research we are examining what is the status of logistics and operations management in Finnish and Swedish companies. Empirical data is based on the web based questionnaire, which was completed in the end of 2007 and early 2008. Our examination consists of roughly 30 answers from largest manufacturing (highest representation in our sample), trade and logistics/distribution companies. Generally it could be argued that these companies operate in complex environment, where number of products, raw materials/components and suppliers is high. However, usually companies rely on small amount of suppliers per raw material/component (highest frequency is 2), and this was especially the case among Swedish companies, and among those companies, which favoured overseas sourcing. Sample consisted of companies which mostly are operating in an international environment, and are quite often multinationals. Our survey findings reveal that companies in general have taken logistics and information technology as part of their strategy process; utilization of performance measures as well as system implementations have followed the strategy decisions. In the transportation mode side we identify that road transports dominate all transport flow classes (inbound, internal and outbound), followed by sea and air. Surprisingly small amount of companies use railways, but in general we could argue that Swedish companies prefer this mode over Finnish counterparts. With respect of operations outsourcing, we found that more traditional areas of logistics outsourcing are driving factors in company's performance measurement priority. In contrary to previous research, our results indicate that the scope of outsourcing is not that wide in logistics/operations management area, and companies are not planning to outsource more in the near future. Some support is found for more international operations and increased outsourcing activity. From the increased time pressure of companies, we find evidence that local as well as overseas customers expect deliveries within days or weeks, but suppliers usually supply within weeks or months. So, basically this leads into considerable inventory holding. Interestingly local and overseas sourcing strategy does not have that great influence on lead time performance of these particular sourcing areas - local strategy is anyway considerably better in responding on market changes due to shorter supply lead times. In the end of our research work we have completed correlation analysis concerning items asked with Likert scale. Our analysis shows that seeing logistics more like a process rather than function, applying time based management, favouring partnerships and measuring logistics within different performance dimensions results on preferred features and performance found in logistics literature.

Implementing Role Based Access Control into the Enterprise Environment to Support Business and IT Functions

The thesis studies role based access control and its suitability in the enterprise environment. The aim is to research how extensively role based access control can be implemented in the case organization and how it support organization’s business and IT functions. This study points out the enterprise’s needs for access control, factors of access control in the enterprise environment and requirements for implementation and the benefits and challenges it brings along. To find the scope how extensively role based access control can be implemented into the case organization, firstly is examined the actual state of access control. Secondly is defined a rudimentary desired state (how things should be) and thirdly completed it by using the results of the implementation of role based access control application. The study results the role model for case organization unit, and the building blocks and the framework for the organization wide implementation. Ultimate value for organization is delivered by facilitating the normal operations of the organization whilst protecting its information assets.

Mobile Subscription Acquisition and Retention Costs - An Actvity-Based Model

The objective of this master’s thesis was to develop a model for mobile subscription acquisition cost, SAC, and mobile subscription retention cost, SRC, by applying activity-based cost accounting principles. The thesis was conducted as a case study for a telecommunication company operating on the Finnish telecommunication market. In addition to activity-based cost accounting there were other theories studied and applied in order to establish a theory framework for this thesis. The concepts of acquisition and retention were explored in a broader context with the concepts of customer satisfaction, loyalty and profitability and eventually customer relationship management to understand the background and meaning of the theme of this thesis. The utilization of SAC and SRC information is discussed through the theories of decision making and activity-based management. Also, the present state and future needs of SAC and SRC information usage at the case company as well as the functions of the company were examined by interviewing some members of the company personnel. With the help of these theories and methods it was aimed at finding out both the theory-based and practical factors which affect the structure of the model. During the thesis study it was confirmed that the existing SAC and SRC model of the case company should be used as the basis in developing the activity-based model. As a result the indirect costs of the old model were transformed into activities and the direct costs were continued to be allocated directly to acquisition of new subscriptions and retention of old subscriptions. The refined model will enable managing the subscription acquisition, retention and the related costs better through the activity information. During the interviews it was found out that the SAC and SRC information is also used in performance measurement and operational and strategic planning. SAC and SRC are not fully absorbed costs and it was concluded that the model serves best as a source of indicative cost information. This thesis does not include calculating costs. Instead, the refined model together with both the theory-based and interview findings concerning the utilization of the information produced by the model will serve as a framework for the possible future development aiming at completing the model.

The Present State and a Development Plan of Cost Accounting in Batch Production of Wind Turbine Gears

The aim of this master’s thesis was to document the present state and to create a development plan for Moventas Wind’s cost accounting. The current cost accounting system was evaluated and most fundamental problems were chosen as areas of focus in development work. The development plan includes both short- and long-term development proposals for problems identified. This report presents two alternative models for product costing. Benchmarking of cost accounting practices and modern cost accounting theories were used in development of cost accounting. It was found that the current cost accounting system functions quite well and the adjustments in unit cost rate calculation have only a minor influence on costs of goods sold. An OEE-based standard cycle concept was also developed and it was found that the implementation of this new system is worthwhile in the long-term.