Developing A Knowledge Management Process Model for Internal IT Organization, Case: Stora Enso Oyj, Corporate IT

The objectives of this Master’s Thesis were to find out what kind of knowledge management strategy would fit best an IT organization that uses ITIL (Information Technology Infrastructure Library) framework for IT Service Management and to create a knowledge management process model to support chosen strategy. The empirical material for this research was collected through qualitative semi-structured interviews of a case organization Stora Enso Corporate IT. The results of the qualitative interviews indicate that codification knowledge management strategy would fit best for the case organization. The knowledge management process model was created based on earlier studies and a literature of knowledge management. The model was evaluated in the interview research and the results showed that the created process model is realistic, useful, and it responds to a real life phenomenon.

Analysis and validation of space averaged drag model for numerical simulations of gas-solid flows in fluidized beds

This thesis presents an approach for formulating and validating a space averaged drag model for coarse mesh simulations of gas-solid flows in fluidized beds using the two-fluid model. Proper modeling for fluid dynamics is central in understanding any industrial multiphase flow. The gas-solid flows in fluidized beds are heterogeneous and usually simulated with the Eulerian description of phases. Such a description requires the usage of fine meshes and small time steps for the proper prediction of its hydrodynamics. Such constraint on the mesh and time step size results in a large number of control volumes and long computational times which are unaffordable for simulations of large scale fluidized beds. If proper closure models are not included, coarse mesh simulations for fluidized beds do not give reasonable results. The coarse mesh simulation fails to resolve the mesoscale structures and results in uniform solids concentration profiles. For a circulating fluidized bed riser, such predicted profiles result in a higher drag force between the gas and solid phase and also overestimated solids mass flux at the outlet. Thus, there is a need to formulate the closure correlations which can accurately predict the hydrodynamics using coarse meshes. This thesis uses the space averaging modeling approach in the formulation of closure models for coarse mesh simulations of the gas-solid flow in fluidized beds using Geldart group B particles. In the analysis of formulating the closure correlation for space averaged drag model, the main parameters for the modeling were found to be the averaging size, solid volume fraction, and distance from the wall. The closure model for the gas-solid drag force was formulated and validated for coarse mesh simulations of the riser, which showed the verification of this modeling approach. Coarse mesh simulations using the corrected drag model resulted in lowered values of solids mass flux. Such an approach is a promising tool in the formulation of appropriate closure models which can be used in coarse mesh simulations of large scale fluidized beds.

Reflexive Space. A Constructionist Model of the Russian Reflexive Marker

This study examines the structure of the Russian Reflexive Marker ( ся/-сь) and offers a usage-based model building on Construction Grammar and a probabilistic view of linguistic structure. Traditionally, reflexive verbs are accounted for relative to non-reflexive verbs. These accounts assume that linguistic structures emerge as pairs. Furthermore, these accounts assume directionality where the semantics and structure of a reflexive verb can be derived from the non-reflexive verb. However, this directionality does not necessarily hold diachronically. Additionally, the semantics and the patterns associated with a particular reflexive verb are not always shared with the non-reflexive verb. Thus, a model is proposed that can accommodate the traditional pairs as well as for the possible deviations without postulating different systems. A random sample of 2000 instances marked with the Reflexive Marker was extracted from the Russian National Corpus and the sample used in this study contains 819 unique reflexive verbs. This study moves away from the traditional pair account and introduces the concept of Neighbor Verb. A neighbor verb exists for a reflexive verb if they share the same phonological form excluding the Reflexive Marker. It is claimed here that the Reflexive Marker constitutes a system in Russian and the relation between the reflexive and neighbor verbs constitutes a cross-paradigmatic relation. Furthermore, the relation between the reflexive and the neighbor verb is argued to be of symbolic connectivity rather than directionality. Effectively, the relation holding between particular instantiations can vary. The theoretical basis of the present study builds on this assumption. Several new variables are examined in order to systematically model variability of this symbolic connectivity, specifically the degree and strength of connectivity between items. In usage-based models, the lexicon does not constitute an unstructured list of items. Instead, items are assumed to be interconnected in a network. This interconnectedness is defined as Neighborhood in this study. Additionally, each verb carves its own niche within the Neighborhood and this interconnectedness is modeled through rhyme verbs constituting the degree of connectivity of a particular verb in the lexicon. The second component of the degree of connectivity concerns the status of a particular verb relative to its rhyme verbs. The connectivity within the neighborhood of a particular verb varies and this variability is quantified by using the Levenshtein distance. The second property of the lexical network is the strength of connectivity between items. Frequency of use has been one of the primary variables in functional linguistics used to probe this. In addition, a new variable called Constructional Entropy is introduced in this study building on information theory. It is a quantification of the amount of information carried by a particular reflexive verb in one or more argument constructions. The results of the lexical connectivity indicate that the reflexive verbs have statistically greater neighborhood distances than the neighbor verbs. This distributional property can be used to motivate the traditional observation that the reflexive verbs tend to have idiosyncratic properties. A set of argument constructions, generalizations over usage patterns, are proposed for the reflexive verbs in this study. In addition to the variables associated with the lexical connectivity, a number of variables proposed in the literature are explored and used as predictors in the model. The second part of this study introduces the use of a machine learning algorithm called Random Forests. The performance of the model indicates that it is capable, up to a degree, of disambiguating the proposed argument construction types of the Russian Reflexive Marker. Additionally, a global ranking of the predictors used in the model is offered. Finally, most construction grammars assume that argument construction form a network structure. A new method is proposed that establishes generalization over the argument constructions referred to as Linking Construction. In sum, this study explores the structural properties of the Russian Reflexive Marker and a new model is set forth that can accommodate both the traditional pairs and potential deviations from it in a principled manner.

Creating a Branding Process Model for Living Area Brands - Developing and managing a new living area brand

The objective of this thesis is to understand how to create and develop a successful place brand and how to manage it systematically. The thesis thoroughly explains the phenomenon of place brands and place branding and presents different sub-categories of place branding. The theoretical part of the thesis provides a wide overview on the prevailing literature of place branding, place brand development and place brand management, which form the basis of the thesis’ theoretical framework. The theoretical evidence is gathered from a case living area. The living area is developed by one construction company, which has a significant role in the construction industry in Finland. The empirical evidence is gathered through semi-structured in-depth interviews by interviewing the new living area’s carefully selected stakeholder groups. Afterwards the empirical data is analyzed and reflected to the theoretical findings. After examining the case living area, the thesis will present a new living area branding process model based on prevailing theories and empirical findings.

Modelling the Knowledge Interface between Sales and Production Functions of a Company. Case: New Service Development Process.

Yrityksen sisäisten rajapintojen tunteminen mahdollistaa tiedonvaihdon hallinnan läpi organisaation. Idean muokkaaminen kannattavaksi innovaatioksi edellyttää organisaation eri osien läpi kulkevaa saumatonta prosessiketjua sekä tietovirtaa. Tutkielman tavoitteena oli mallintaa organisaation kahden toiminnallisesti erilaisen osan välinen tiedon vaihto. Tiedon vaihto kuvattiin rajapintana, tietoliittymänä. Kolmiulotteinen organisaatiomalli muodosti tutkimuksen pääteorian. Se kytkettiin yrityksen tuotanto- ja myyntiosiin, kuten myös BestServ-projektin kehittämään uuteen palvelujen kehittämisen prosessiin. Uutta palvelujen kehittämisen prosessia laajennettiin ISO/IEC 15288 standardin kuvaamalla prosessimallilla. Yritysarkkitehtuurikehikoita käytettiin mallintamisen perustana. Tietoliittymä nimenä kuvastaa näkemystä siitä, että tieto [tietämys] on olemukseltaan yksilöiden tai ryhmien välistä. Mallinnusmenetelmät eivät kuitenkaan vielä mahdollista tietoon [tietämykseen] liittyvien kaikkien ominaisuuksien mallintamista. Tietoliittymän malli koostuu kolmesta osasta, joista kaksi esitetään graafisessa muodossa ja yksi taulukkona. Mallia voidaan käyttää itsenäisesti tai osana yritysarkkitehtuuria. Teollisessa palveluliiketoiminnassa sekä tietoliittymän mallinnusmenetelmä että sillä luotu malli voivat auttaa konepajateollisuuden yritystä ymmärtämään yrityksen kehittämistarpeet ja -kohteet, kun se haluaa palvelujen tuottamisella suuremman roolin asiakasyrityksen liiketoiminnassa. Tietoliittymän mallia voidaan käyttää apuna organisaation tietovarannon ja tietämyksen mallintamisessa sekä hallinnassa ja näin pyrkiä yhdistämään ne yrityksen strategiaa palvelevaksi kokonaisuudeksi. Tietoliittymän mallinnus tarjoaa tietojohtamisen kauppatieteelliselle tutkimukselle menetelmällisyyden tutkia innovaatioiden hallintaa sekä organisaation uudistumiskykyä. Kumpikin tutkimusalue tarvitsevat tarkempaa tietoa ja mahdollisuuksia hallita tietovirtoja, tiedon vaihtoa sekä organisaation tietovarannon käyttöä.

Dynamic Model of a Small Once-Through Boiler

In this study, a model for the unsteady dynamic behaviour of a once-through counter flow boiler that uses an organic working fluid is presented. The boiler is a compact waste-heat boiler without a furnace and it has a preheater, a vaporiser and a superheater. The relative lengths of the boiler parts vary with the operating conditions since they are all parts of a single tube. The present research is a part of a study on the unsteady dynamics of an organic Rankine cycle power plant and it will be a part of a dynamic process model. The boiler model is presented using a selected example case that uses toluene as the process fluid and flue gas from natural gas combustion as the heat source. The dynamic behaviour of the boiler means transition from the steady initial state towards another steady state that corresponds to the changed process conditions. The solution method chosen was to find such a pressure of the process fluid that the mass of the process fluid in the boiler equals the mass calculated using the mass flows into and out of the boiler during a time step, using the finite difference method. A special method of fast calculation of the thermal properties has been used, because most of the calculation time is spent in calculating the fluid properties. The boiler was divided into elements. The values of the thermodynamic properties and mass flows were calculated in the nodes that connect the elements. Dynamic behaviour was limited to the process fluid and tube wall, and the heat source was regarded as to be steady. The elements that connect the preheater to thevaporiser and the vaporiser to the superheater were treated in a special way that takes into account a flexible change from one part to the other. The model consists of the calculation of the steady state initial distribution of the variables in the nodes, and the calculation of these nodal values in a dynamic state. The initial state of the boiler was received from a steady process model that isnot a part of the boiler model. The known boundary values that may vary during the dynamic calculation were the inlet temperature and mass flow rates of both the heat source and the process fluid. A brief examination of the oscillation around a steady state, the so-called Ledinegg instability, was done. This examination showed that the pressure drop in the boiler is a third degree polynomial of the mass flow rate, and the stability criterion is a second degree polynomial of the enthalpy change in the preheater. The numerical examination showed that oscillations did not exist in the example case. The dynamic boiler model was analysed for linear and step changes of the entering fluid temperatures and flow rates.The problem for verifying the correctness of the achieved results was that there was no possibility o compare them with measurements. This is why the only way was to determine whether the obtained results were intuitively reasonable and the results changed logically when the boundary conditions were changed. The numerical stability was checked in a test run in which there was no change in input values. The differences compared with the initial values were so small that the effects of numerical oscillations were negligible. The heat source side tests showed that the model gives results that are logical in the directions of the changes, and the order of magnitude of the timescale of changes is also as expected. The results of the tests on the process fluid side showed that the model gives reasonable results both on the temperature changes that cause small alterations in the process state and on mass flow rate changes causing very great alterations. The test runs showed that the dynamic model has no problems in calculating cases in which temperature of the entering heat source suddenly goes below that of the tube wall or the process fluid.

Applying the principles of life cycle assessment and costing in process modeling to examine profit-making capability

Static process simulation has traditionally been used to model complex processes for various purposes. However, the use of static processsimulators for the preparation of holistic examinations aiming at improving profit-making capability requires a lot of work because the production of results requires the assessment of the applicability of detailed data which may be irrelevant to the objective. The relevant data for the total assessment gets buried byirrelevant data. Furthermore, the models do not include an examination of the maintenance or risk management, and economic examination is often an extra property added to them which can be performed with a spreadsheet program. A process model applicable to holistic economic examinations has been developed in this work. The model is based on the life cycle profit philosophy developed by Hagberg and Henriksson in 1996. The construction of the model has utilized life cycle assessment and life cycle costing methodologies with a view to developing, above all, a model which would be applicable to the economic examinations of complete wholes and which would require the need for information focusing on aspects essential to the objectives. Life cycle assessment and costing differ from each other in terms of the modeling principles, but the features of bothmethodologies can be used in the development of economic process modeling. Methods applicable to the modeling of complex processes can be examined from the viewpoint of life cycle methodologies, because they involve the collection and management of large corpuses of information and the production of information for the needs of decision-makers as well. The results of the study shows that on the basis of the principles of life cycle modeling, a process model can be created which may be used to produce holistic efficiency examinations on the profit-making capability of the production line, with fewer resources thanwith traditional methods. The calculations of the model are based to the maximum extent on the information system of the factory, which means that the accuracyof the results can be improved by developing information systems so that they can provide the best information for this kind of examinations.

Influence of software development process quality on product quality

Ohjelmistojen tärkeys nykypäivän yhteiskunnalle kasvaa jatkuvasti. Monia ohjelmistoprojekteja vaivaavat ongelmat aikataulussa pysymisestä, korkean tuottavuuden ylläpitämisestä ja riittävän korkeasta laadusta. Ohjelmistokehitysprosessien parantamisessa on naiden ongelmien minimoimiseksi tehty suuria investointeja. Investointien syynä on ollut olettamus ohjelmistokehityksen kapasiteetin suora riippuvuus tuotteen laadusta. Tämän tutkimuksen tarkoituksena oli tutkia Ohjelmistokehitysprosessien parantamisen mahdollisuuksia. Olemassaolevat ohjelmistokehityksen ja Ohjelmistokehitysprosessin parantamisen mallit, tekniikat ja metodologiat esiteltiin. Esiteltyjen mallien, tekniikoiden ja metodologioiden soveltuvuus analysoitiin ja suositus mallien käytöstä annettiin.

Product Definition Process for Mobile Radio System Product

Työn tarkoituksena oli tutkia tuotteen määrittelyyn liittyvää kirjallisuutta ja perehtyä tuotteen määrittelytyön nykytilaan kohdeyrityksessä. Näihin molempiin perustuen muodostetaan prosessimalli tuotteen määrittelytyölle kohdeyrityksessä. Työssä käsitellään prosessijohtamisen pääperiaatteet sekä tuotteen määrittelyä koskevaa kirjallisuutta ja tutkimuksia. Koska kysessä oleva tuote on suurelta osalta ohjelmistotuote, ohjelmistojen suunnittelua, erityisesti ohjelmistovaatimusten hallintaa ja ohjelmistojen määrittelyä, on myös tarkasteltu työssä. Tuotteen määrittelyn haasteita on käsitelty yksityiskohtaisemmin, esimerkiksi dokumentointia, prosessin kulkua, vaatimusten epävakaisuutta sekä muutoksia. Kohdeyritys ja sen ongelmakohdat esitellään ja luodaan prosessimalli. Tämä malli esittelee seuraavat prosessit: raakavaatimusten hallinta -prosessin, roadmapping -prosessin, esisuunnittelu- ja spesifikaatioprosessin ja julkaisun suunnittelu -prosessin. Kaikki nämä ovat vaiheita ennen varsinaisen tuotekehitysprojektin aloittamista. Työssä esitellään myös kolmetasoinen dokumentaatiomalli.

Wireless Applications Evaluation and Development Process: Case -Paper Industry Logistics

Sähköisen liiketoiminnan ja mobiliteetin konvergenssi yhdessä teknologisen innovaation kiihtyvän vauhdin kanssa ovat saaneet aikaan kiinnostusta langattomia liiketoimintaratkaisuja kohtaan. Tämän diplomityön tavoitteena oli tutkia sähköisen liiketoiminnan langattomien sovellusten arviointi- ja kehitysprosessia. Työ keskittyy tarkastelemaan paperiteollisuuden toimitusketjun langatonta seurantaa. Tutkimuksessa esitetään langattoman sähköisen liiketoiminnan määritelmä, kuvaillaan langattomuuden eri sovellusalueita ja sovellusten arviointi- ja kehitysprosessin strategisia sekä teknologisia ulottuvuuksia. Työ luo viitekehyksen, jonka avulla tarkastella langattomien teknologioiden merkitystä logistiikassa. Tutkimuksen merkittävin tulos on prosessimalli sovellusten arvioimiseksi ja kehittämiseksi. Mallilla kehitetty langaton sovellus osoittautui tarkastelussa hyödylliseksi toimitusketjun hallinnassa.

Outsourcing process in pharmaceutical product development

The aim of this study was to create an outsourcing process for pharmaceutical product development. This study focuses on two main questions. The first question is “What is the outsourcing process model?” In the second phase key success factors of the outsourcing process are identified. As a result of the literature reviews, a general outsourcing process was created. Transaction cost economics and resource based view were used to derived a theoretical framework to the process by combining the existing processes presented in the literature. The model of process is considered used to the outsourcing broadly. The general outsourcing process was then developed further with the key factors that affect the success of pharmaceutical product development and the interviews of pharmaceutical outsourcing experts. The result of the research was the process consists of seven phases with key activities and expected outputs for each of the phases. In addition, the strategic decision-making framework for outsourcing decision in pharmaceutical product development is giving as well as the tools for selecting supplier and preparing structured contract. This study also gives some recommendations for managing the outsourcing process.

Requirements management process

Vaatimustenhallinnan alue on hyvin kompleksinen. Sen terminologia on moninaista ja samat termit voivat tarkoittaa eri asioita eri ihmisille. Tämän työn tarkoituksena on selkeyttää vaatimustenhallinnan aluetta. Se vastaa kysymyksiin kuten, mitä vaatimustenhallinta on ja miten sitä voidaan tehdä. Työ keskittyy vaatimusten analysoinnin ja validoinnin alueisiin, joten tältä osin se vastaa myös tarkempiin kysymyksiin kuten, miten koottujen vaatimusten jäljitettävyyttä, dokumentointia, analysointia ja validointia voidaan tehdä. Tämän työn kautta vaatimustenhallinta voidaan esitellä yritykselle ja sen eri osat voivat saada saman käsityksen vaatimustenhallinnasta. Tutkimus esittelee vaatimustenhallinnan prosessina, joka pitää sisällään vaatimusten jäljitettävyyden, vaatimusten dokumentoinnin, vaatimusten muutoksenhallinnan ja vaatimusmäärityksen. Vaatimusmääritys voidaan edelleen jakaa vaatimusten koostamiseen, analysointiin ja neuvotteluun sekä validointiin. Työssä esitellään geneerinen vaatimustenhallinnan prosessimalli. Mallin avulla näytetään, että vaatimustenhallinta on jatkuva prosessi, jossa kaikki aktiviteetit ovat kytköksissä toisiinsa. Näitä aktiviteettejä suoritetaan enemmän tai vähemmän samanaikaisesti. Malli esitetään geneerisessä muodossa, jotta se olisi hyödynnettävissä systeemi- ja tuotekehitys projekteissa sekä sisäisissä kehitysprojekteissa. Se kertoo, että vaatimukset tulisi jalostaa niin aikaisin, kuin mahdollista, jotta muutoksien määrä kehitystyön myöhemmissä vaiheissa voitaisiin minimoida. Jotkin muutokset eivät ole vältettävissä, joten muutoksenhallinnan tueksi tulisi kehittää jäljitettävyyskäsikirja ja jäljitettävyyskäytännöt. Vaatimustenhallintaa tarkastellaan meneillään olevassa kehitysprojektissa. Tarkastelussa tutkitaan, mitä vaatimustenhallinnan toimintatapoja sekä analysointi- ja validointimetodeja käytetään ja mitä voitaisiin tehdä vaatimustenhallinnan parantamiseksi projektissa.

Developing a Brand Positioning Model for International Strategic Marketing

The target of this thesis is to develop a brand positioning process model for the case company’s international operations. The model will make the process more effective and decrease the risk of relevant aspects being forgotten. The focus is on the international operations although generally the brand positioning can be seen as a standardized subject and, thus, there is no need to distinguish market areas. Constructive research approach is chosen as a research method. Internal interviews are done in order to give the much needed insight about the case company’s current processes and circumstances. Based on theory, interviews as well as internal and external material the model is built. The most difficult part in building the model is to determine the order of each phase. Also, deciding the number of each phase can be problematic. The model should be brief and assertive in order to reduce the risk of misunderstanding between employees from different units. Based on the analysis of the interviews and the theory the brand positioning process model is presented with indication of the order of each phase. The model is divided to three main groups: Analyzing the Environment, Determining the Brand Position, and Documenting the BPS. The benefits of the model are that overlapping work can be reduced, too similar brands can be noticed and it is easier to train new employees.

Modeling of high pressure pretreatment process for gold leaching

Investigation of high pressure pretreatment process for gold leaching is the objective of the present master's thesis. The gold ores and concentrates which cannot be easily treated by leaching process are called "refractory". These types of ores or concentrates often have high content of sulfur and arsenic that renders the precious metal inaccessible to the leaching agents. Since the refractory ores in gold manufacturing industry take a considerable share, the pressure oxidation method (autoclave method) is considered as one of the possible ways to overcome the related problems. Mathematical modeling is the main approach in this thesis which was used for investigation of high pressure oxidation process. For this task, available information from literature concerning this phenomenon, including chemistry, mass transfer and kinetics, reaction conditions, applied apparatus and application, was collected and studied. The modeling part includes investigation of pyrite oxidation kinetics in order to create a descriptive mathematical model. The following major steps are completed: creation of process model by using the available knowledge; estimation of unknown parameters and determination of goodness of the fit; study of the reliability of the model and its parameters.

Particle model for simulating limestone reactions in novel fluidised bed energy applications

The development of carbon capture and storage (CCS) has raised interest towards novel fluidised bed (FB) energy applications. In these applications, limestone can be utilized for S02 and/or CO2 capture. The conditions in the new applications differ from the traditional atmospheric and pressurised circulating fluidised bed (CFB) combustion conditions in which the limestone is successfully used for SO2 capture. In this work, a detailed physical single particle model with a description of the mass and energy transfer inside the particle for limestone was developed. The novelty of this model was to take into account the simultaneous reactions, changing conditions, and the effect of advection. Especially, the capability to study the cyclic behaviour of limestone on both sides of the calcination-carbonation equilibrium curve is important in the novel conditions. The significances of including advection or assuming diffusion control were studied in calcination. Especially, the effect of advection in calcination reaction in the novel combustion atmosphere was shown. The model was tested against experimental data; sulphur capture was studied in a laboratory reactor in different fluidised bed conditions. Different Conversion levels and sulphation patterns were examined in different atmospheres for one limestone type. The Conversion curves were well predicted with the model, and the mechanisms leading to the Conversion patterns were explained with the model simulations. In this work, it was also evaluated whether the transient environment has an effect on the limestone behaviour compared to the averaged conditions and in which conditions the effect is the largest. The difference between the averaged and transient conditions was notable only in the conditions which were close to the calcination-carbonation equilibrium curve. The results of this study suggest that the development of a simplified particle model requires a proper understanding of physical and chemical processes taking place in the particle during the reactions. The results of the study will be required when analysing complex limestone reaction phenomena or when developing the description of limestone behaviour in comprehensive 3D process models. In order to transfer the experimental observations to furnace conditions, the relevant mechanisms that take place need to be understood before the important ones can be selected for 3D process model. This study revealed the sulphur capture behaviour under transient oxy-fuel conditions, which is important when the oxy-fuel CFB process and process model are developed.