Use of neural networks in robot positioning of large flexible redundant manipulators

Deflection compensation of flexible boom structures in robot positioning is usually done using tables containing the magnitude of the deflection with inverse kinematics solutions of a rigid structure. The number of table values increases greatly if the working area of the boom is large and the required positioning accuracy is high. The inverse kinematics problems are very nonlinear, and if the structure is redundant, in some cases it cannot be solved in a closed form. If the structural flexibility of the manipulator arms is taken into account, the problem is almost impossible to solve using analytical methods. Neural networks offer a possibility to approximate any linear or nonlinear function. This study presents four different methods of using neural networks in the static deflection compensation and inverse kinematics solution of a flexible hydraulically driven manipulator. The training information required for training neural networks is obtained by employing a simulation model that includes elasticity characteristics. The functionality of the presented methods is tested based on the simulated and measured results of positioning accuracy. The simulated positioning accuracy is tested in 25 separate coordinate points. For each point, the positioning is tested with five different mass loads. The mean positioning error of a manipulator decreased from 31.9 mm to 4.1 mm in the test points. This accuracy enables the use of flexible manipulators in the positioning of larger objects. The measured positioning accuracy is tested in 9 separate points using three different mass loads. The mean positioning error decreased from 10.6 mm to 4.7 mm and the maximum error from 27.5 mm to 11.0 mm.

Novel Methods for Error Modeling and Parameter Identification of a Redundant Serial-Parallel Hybrid Robot

To obtain the desirable accuracy of a robot, there are two techniques available. The first option would be to make the robot match the nominal mathematic model. In other words, the manufacturing and assembling tolerances of every part would be extremely tight so that all of the various parameters would match the “design” or “nominal” values as closely as possible. This method can satisfy most of the accuracy requirements， but the cost would increase dramatically as the accuracy requirement increases. Alternatively, a more cost-effective solution is to build a manipulator with relaxed manufacturing and assembling tolerances. By modifying the mathematical model in the controller, the actual errors of the robot can be compensated. This is the essence of robot calibration. Simply put, robot calibration is the process of defining an appropriate error model and then identifying the various parameter errors that make the error model match the robot as closely as possible. This work focuses on kinematic calibration of a 10 degree-of-freedom (DOF) redundant serial-parallel hybrid robot. The robot consists of a 4-DOF serial mechanism and a 6-DOF hexapod parallel manipulator. The redundant 4-DOF serial structure is used to enlarge workspace and the 6-DOF hexapod manipulator is used to provide high load capabilities and stiffness for the whole structure. The main objective of the study is to develop a suitable calibration method to improve the accuracy of the redundant serial-parallel hybrid robot. To this end, a Denavit–Hartenberg (DH) hybrid error model and a Product-of-Exponential (POE) error model are developed for error modeling of the proposed robot. Furthermore, two kinds of global optimization methods, i.e. the differential-evolution (DE) algorithm and the Markov Chain Monte Carlo (MCMC) algorithm, are employed to identify the parameter errors of the derived error model. A measurement method based on a 3-2-1 wire-based pose estimation system is proposed and implemented in a Solidworks environment to simulate the real experimental validations. Numerical simulations and Solidworks prototype-model validations are carried out on the hybrid robot to verify the effectiveness, accuracy and robustness of the calibration algorithms.

On sliding mode control ofhydraulic servo systems and a manipulator

The aim of the study is to developa novel robust controller based on sliding mode control technique for the hydraulic servo system with flexible load and for a flexible manipulator with the lift and jib hydraulic actuators. For the purpose of general control design, a dynamic model is derived describing the principle physical behavior for both the hydraulic servo system and the flexible hydraulic manipulator. The mechanism of hydraulic servo systems is described by basic mathematical equations of fluid powersystems and the dynamics of flexible manipulator is modeled by the assumed modemethod. The controller is constructed so as to track desired trajectories in the presence of model imprecision. Experimental and simulation results demonstratethat sliding mode control has benefits which can be used to guarantee stabilityin uncertain systems and improve the system performance and load tolerance.

Novel Robot Solutions for Carrying out Field Joint Welding and Machining in the Assembly of the Vacuum Vessel of ITER

It is necessary to use highly specialized robots in ITER (International Thermonuclear Experimental Reactor) both in the manufacturing and maintenance of the reactor due to a demanding environment. The sectors of the ITER vacuum vessel (VV) require more stringent tolerances than normally expected for the size of the structure involved. VV consists of nine sectors that are to be welded together. The vacuum vessel has a toroidal chamber structure. The task of the designed robot is to carry the welding apparatus along a path with a stringent tolerance during the assembly operation. In addition to the initial vacuum vessel assembly, after a limited running period, sectors need to be replaced for repair. Mechanisms with closed-loop kinematic chains are used in the design of robots in this work. One version is a purely parallel manipulator and another is a hybrid manipulator where the parallel and serial structures are combined. Traditional industrial robots that generally have the links actuated in series are inherently not very rigid and have poor dynamic performance in high speed and high dynamic loading conditions. Compared with open chain manipulators, parallel manipulators have high stiffness, high accuracy and a high force/torque capacity in a reduced workspace. Parallel manipulators have a mechanical architecture where all of the links are connected to the base and to the end-effector of the robot. The purpose of this thesis is to develop special parallel robots for the assembly, machining and repairing of the VV of the ITER. The process of the assembly and machining of the vacuum vessel needs a special robot. By studying the structure of the vacuum vessel, two novel parallel robots were designed and built; they have six and ten degrees of freedom driven by hydraulic cylinders and electrical servo motors. Kinematic models for the proposed robots were defined and two prototypes built. Experiments for machine cutting and laser welding with the 6-DOF robot were carried out. It was demonstrated that the parallel robots are capable of holding all necessary machining tools and welding end-effectors in all positions accurately and stably inside the vacuum vessel sector. The kinematic models appeared to be complex especially in the case of the 10-DOF robot because of its redundant structure. Multibody dynamics simulations were carried out, ensuring sufficient stiffness during the robot motion. The entire design and testing processes of the robots appeared to be complex tasks due to the high specialization of the manufacturing technology needed in the ITER reactor, while the results demonstrate the applicability of the proposed solutions quite well. The results offer not only devices but also a methodology for the assembly and repair of ITER by means of parallel robots.

Redundant Ethernet-based fieldbuses

Ethernet-pohjaisten kenttäväylien suosio teollisuudessa on kasvanut viime aikoina voimakkaasti. Ethernet tarjoaa suuren bittinopeuden, edulliset laitteet ja tekniikkaa on tutkittu laajasti. Diplomityö esittelee Ethernet-tekniikan perusteet ja joitakin teollisuudessa käytettäviä Ethernet-pohjaisia kenttäväyläprotokollia. Työn tarkoitus on tehdä tiivis käsikirja eri Ethernet-pohjaisista kenttäväyläprotokollista ja erityisesti niiden redundanttisuusominaisuuksista. Lähempään tarkasteluun on otettu redundantti EtherNet/IP ja sen alemmat kerrokset, sekä implementoitu redundanttisuus ABB:n ACS350-taajuusmuuttajaan.

Flexible multibody dynamics and intelligent control of a hydraulically driven hybrid redundant robot machine

The assembly and maintenance of the International Thermonuclear Experimental Reactor (ITER) vacuum vessel (VV) is highly challenging since the tasks performed by the robot involve welding, material handling, and machine cutting from inside the VV. The VV is made of stainless steel, which has poor machinability and tends to work harden very rapidly, and all the machining operations need to be carried out from inside of the ITER VV. A general industrial robot cannot be used due to its poor stiffness in the heavy duty machining process, and this will cause many problems, such as poor surface quality, tool damage, low accuracy. Therefore, one of the most suitable options should be a light weight mobile robot which is able to move around inside of the VV and perform different machining tasks by replacing different cutting tools. Reducing the mass of the robot manipulators offers many advantages: reduced material costs, reduced power consumption, the possibility of using smaller actuators, and a higher payload-to-robot weight ratio. Offsetting these advantages, the lighter weight robot is more flexible, which makes it more difficult to control. To achieve good machining surface quality, the tracking of the end effector must be accurate, and an accurate model for a more flexible robot must be constructed. This thesis studies the dynamics and control of a 10 degree-of-freedom (DOF) redundant hybrid robot (4-DOF serial mechanism and 6-DOF 6-UPS hexapod parallel mechanisms) hydraulically driven with flexible rods under the influence of machining forces. Firstly, the flexibility of the bodies is described using the floating frame of reference method (FFRF). A finite element model (FEM) provided the Craig-Bampton (CB) modes needed for the FFRF. A dynamic model of the system of six closed loop mechanisms was assembled using the constrained Lagrange equations and the Lagrange multiplier method. Subsequently, the reaction forces between the parallel and serial parts were used to study the dynamics of the serial robot. A PID control based on position predictions was implemented independently to control the hydraulic cylinders of the robot. Secondly, in machining, to achieve greater end effector trajectory tracking accuracy for surface quality, a robust control of the actuators for the flexible link has to be deduced. This thesis investigates the intelligent control of a hydraulically driven parallel robot part based on the dynamic model and two schemes of intelligent control for a hydraulically driven parallel mechanism based on the dynamic model: (1) a fuzzy-PID self-tuning controller composed of the conventional PID control and with fuzzy logic, and (2) adaptive neuro-fuzzy inference system-PID (ANFIS-PID) self-tuning of the gains of the PID controller, which are implemented independently to control each hydraulic cylinder of the parallel mechanism based on rod length predictions. The serial component of the hybrid robot can be analyzed using the equilibrium of reaction forces at the universal joint connections of the hexa-element. To achieve precise positional control of the end effector for maximum precision machining, the hydraulic cylinder should be controlled to hold the hexa-element. Thirdly, a finite element approach of multibody systems using the Special Euclidean group SE(3) framework is presented for a parallel mechanism with flexible piston rods under the influence of machining forces. The flexibility of the bodies is described using the nonlinear interpolation method with an exponential map. The equations of motion take the form of a differential algebraic equation on a Lie group, which is solved using a Lie group time integration scheme. The method relies on the local description of motions, so that it provides a singularity-free formulation, and no parameterization of the nodal variables needs to be introduced. The flexible slider constraint is formulated using a Lie group and used for modeling a flexible rod sliding inside a cylinder. The dynamic model of the system of six closed loop mechanisms was assembled using Hamilton’s principle and the Lagrange multiplier method. A linearized hydraulic control system based on rod length predictions was implemented independently to control the hydraulic cylinders. Consequently, the results of the simulations demonstrating the behavior of the robot machine are presented for each case study. In conclusion, this thesis studies the dynamic analysis of a special hybrid (serialparallel) robot for the above-mentioned special task involving the ITER and investigates different control algorithms that can significantly improve machining performance. These analyses and results provide valuable insight into the design and control of the parallel robot with flexible rods.

Stiffness based trajectory planning and feedforward based vibration suppression control of parallel robot machines

The dissertation proposes two control strategies, which include the trajectory planning and vibration suppression, for a kinematic redundant serial-parallel robot machine, with the aim of attaining the satisfactory machining performance. For a given prescribed trajectory of the robot's end-effector in the Cartesian space, a set of trajectories in the robot's joint space are generated based on the best stiffness performance of the robot along the prescribed trajectory. To construct the required system-wide analytical stiffness model for the serial-parallel robot machine, a variant of the virtual joint method (VJM) is proposed in the dissertation. The modified method is an evolution of Gosselin's lumped model that can account for the deformations of a flexible link in more directions. The effectiveness of this VJM variant is validated by comparing the computed stiffness results of a flexible link with the those of a matrix structural analysis (MSA) method. The comparison shows that the numerical results from both methods on an individual flexible beam are almost identical, which, in some sense, provides mutual validation. The most prominent advantage of the presented VJM variant compared with the MSA method is that it can be applied in a flexible structure system with complicated kinematics formed in terms of flexible serial links and joints. Moreover, by combining the VJM variant and the virtual work principle, a systemwide analytical stiffness model can be easily obtained for mechanisms with both serial kinematics and parallel kinematics. In the dissertation, a system-wide stiffness model of a kinematic redundant serial-parallel robot machine is constructed based on integration of the VJM variant and the virtual work principle. Numerical results of its stiffness performance are reported. For a kinematic redundant robot, to generate a set of feasible joints' trajectories for a prescribed trajectory of its end-effector, its system-wide stiffness performance is taken as the constraint in the joints trajectory planning in the dissertation. For a prescribed location of the end-effector, the robot permits an infinite number of inverse solutions, which consequently yields infinite kinds of stiffness performance. Therefore, a differential evolution (DE) algorithm in which the positions of redundant joints in the kinematics are taken as input variables was employed to search for the best stiffness performance of the robot. Numerical results of the generated joint trajectories are given for a kinematic redundant serial-parallel robot machine, IWR (Intersector Welding/Cutting Robot), when a particular trajectory of its end-effector has been prescribed. The numerical results show that the joint trajectories generated based on the stiffness optimization are feasible for realization in the control system since they are acceptably smooth. The results imply that the stiffness performance of the robot machine deviates smoothly with respect to the kinematic configuration in the adjacent domain of its best stiffness performance. To suppress the vibration of the robot machine due to varying cutting force during the machining process, this dissertation proposed a feedforward control strategy, which is constructed based on the derived inverse dynamics model of target system. The effectiveness of applying such a feedforward control in the vibration suppression has been validated in a parallel manipulator in the software environment. The experimental study of such a feedforward control has also been included in the dissertation. The difficulties of modelling the actual system due to the unknown components in its dynamics is noticed. As a solution, a back propagation (BP) neural network is proposed for identification of the unknown components of the dynamics model of the target system. To train such a BP neural network, a modified Levenberg-Marquardt algorithm that can utilize an experimental input-output data set of the entire dynamic system is introduced in the dissertation. Validation of the BP neural network and the modified Levenberg- Marquardt algorithm is done, respectively, by a sinusoidal output approximation, a second order system parameters estimation, and a friction model estimation of a parallel manipulator, which represent three different application aspects of this method.

Automaattisen pakkauskoneen käyttövarmuuden varmentaminen

Työn tavoitteena oli selvittää ja varmistaa uuden pakkauskoneen riittävä käyttövarmuus. Käyttövarmuuden selvittämistä varten tutustuttiin käyttövarmuuden käsitteisiin jatunnuslukuihin, sekä selvitettiin kunnossapidon merkitystä käyttövarmuuteen. Pakkauskoneen käyttövarmuutta analysoitiin vikapuumallin avulla. Analysointia varten laadittu vikapuumalli koostuu 391 perustapahtumasta ja yhteensä 629 tapahtumasta. Käyttövarmuusanalyysi suoritettiin kvalitatiivisesti ja kvantitatiivisesti. Analysointi painottuu kuitenkin kvantitatiiviseen simulointiin. Käyttövarmuusanalysoinnin apuna käytettiin simulointiohjelmaa. Käyttövarmuusvaatimukseksi asetettiin 99 % käytettävyys vuoden käyttöjakson aikana. Vikapuuanalyysin tuloksena saatiin arvio pakkauskoneen kokonaiskäytettävyydestä. Kokonaiskäytettävyydeksi muodostui 96,44 %, joka ei täytä käyttövarmuusvaatimusta. Yksittäisistä komponenttityypeistä epäluotettavimpia olivat liimalaitteiston ja paineilmajärjestelmän komponentit. Analysointityökalun avulla voitiin osoittaa käyttövarmuutta parantavien osatekijöiden vaikutukset saatuun kokonaiskäytettävyyteen. Käyttövarmuuteen voitiin vaikuttaa kunnossapidon avulla, lyhentämällä korjausaikaa ja varmentamalla komponentteja. Esitettyjen keinojen avulla käytettävyyttä on mahdollista nostaa n. 2,18 prosenttiyksikköä. Toimenpidesuositukset esitettiin saatujen tulosten ja työssä havainnoitujen asioiden perusteella. Käytettävyyden parantamiseksi ja varmistamiseksi suositetaan oikeanlaisia kunnossapitotoimenpiteitä, tehokkaan vikadiagnostiikan rakentamista sekä antureiden varmentamista. Käyttökunnonvalvonta suositetaan suoritettavaksi määräaikaistarkastuksina. Käyttökuntoa on aloitettava seuraamaan pidemmällä aikavälillä tapahtuvina häiriöraportointeina. Lisäksi tulevaisuudessa on vaadittava käyttövarmuustakuut toimittajilta laitehankintojen yhteydessä.

In-Vessel Penetrator -käärmerobotin mallinnus ADAMS-ohjelmistolla

Työn tavoitteena oli muodostaa virtuaaliprototyyppi fuusioreaktorin huollossa käytettävästä IVP-robotista. Työssä mallinnettiin robotin mekaniikka joustavana sekä toimilaitteiden ja käyttöjen dynaamiset ominaisuudet valmistajien esitietojen ja mitoitustietojen perusteella. Käyttöjen ja mekaniikan mallit yhdistettiin ADAMS-ohjelmistossa. Mekaanisten joustojen mallinnuksessa sekä verifioinnissa käytettiin apuna ANSYS –ohjelmistoa. Virtuaaliprototyypin toimivuudesta varmistuttiin vertaamalla sitä robotin suunnittelutietoihin ja fyysiseen prototyyppiin. Robotin ohjauksessa käytettävän P-säätäjän vaikutusta tutkittiin eri vahvistuksen arvoilla sekä verrattiin mekaanisia vasteita fyysisen prototyypin dynaamisiin testeihin. Esimerkkinä robotin käyttäytymisestä todellisessa tilanteessa simuloitiin sen ajoa reaktoriin. Toteutetun simulointimallin todettiin vastaavan rakenteeltaan sekä siinä esiintyvien voimien osalta suunnitelmien mukaista konstruktiota. Käytetyillä parametreilla se toteutti hyvin robotille asetetut nopeusvaatimukset.

Type II aromatic polyketide biosynthetic tailoring enzymes: diversity and adaptation in Streptomyces secondary metabolism.

Members of the bacterial genus Streptomyces are well known for their ability to produce an exceptionally wide selection of diverse secondary metabolites. These include natural bioactive chemical compounds which have potential applications in medicine, agriculture and other fields of commerce. The outstanding biosynthetic capacity derives from the characteristic genetic flexibility of Streptomyces secondary metabolism pathways: i) Clustering of the biosynthetic genes in chromosome regions redundant for vital primary functions, and ii) the presence of numerous genetic elements within these regions which facilitate DNA rearrangement and transfer between non-progeny species. Decades of intensive genetic research on the organization and function of the biosynthetic routes has led to a variety of molecular biology applications, which can be used to expand the diversity of compounds synthesized. These include techniques which, for example, allow modification and artificial construction of novel pathways, and enable gene-level detection of silent secondary metabolite clusters. Over the years the research has expanded to cover molecular-level analysis of the enzymes responsible for the individual catalytic reactions. In vitro studies of the enzymes provide a detailed insight into their catalytic functions, mechanisms, substrate specificities, interactions and stereochemical determinants. These are factors that are essential for the thorough understanding and rational design of novel biosynthetic routes. The current study is a part of a more extensive research project (Antibiotic Biosynthetic Enzymes; www.sci.utu.fi/projects/biokemia/abe), which focuses on the post-PKS tailoring enzymes involved in various type II aromatic polyketide biosynthetic pathways in Streptomyces bacteria. The initiative here was to investigate specific catalytic steps in anthracycline and angucycline biosynthesis through in vitro biochemical enzyme characterization and structural enzymology. The objectives were to elucidate detailed mechanisms and enzyme-level interactions which cannot be resolved by in vivo genetic studies alone. The first part of the experimental work concerns the homologous polyketide cyclases SnoaL and AknH. These catalyze the closure of the last carbon ring of the tetracyclic carbon frame common to all anthracycline-type compounds. The second part of the study primarily deals with tailoring enzymes PgaE (and its homolog CabE) and PgaM, which are responsible for a cascade of sequential modification reactions in angucycline biosynthesis. The results complemented earlier in vivo findings and confirmed the enzyme functions in vitro. Importantly, we were able to identify the amino acid -level determinants that influence AknH and SnoaL stereoselectivity and to determine the complex biosynthetic steps of the angucycline oxygenation cascade of PgaE and PgaM. In addition, the findings revealed interesting cases of enzyme-level adaptation, as some of the catalytic mechanisms did not coincide with those described for characterised homologs or enzymes of known function. Specifically, SnoaL and AknH were shown to employ a novel acid-base mechanism for aldol condenzation, whereas the hydroxylation reaction catalysed by PgaM involved unexpected oxygen chemistry. Owing to a gene-level fusion of two ancestral reading frames, PgaM was also shown to adopt an unusual quaternary sturucture, a non-covalent fusion complex of two alternative forms of the protein. Furthermore, the work highlighted some common themes encountered in polyketide biosynthetic pathways such as enzyme substrate specificity and intermediate reactivity. These are discussed in the final chapters of the work.

Error Modeling and Accuracy Analysis of a Novel Mobile Hybrid Parallel Robot

Over the last decades, calibration techniques have been widely used to improve the accuracy of robots and machine tools since they only involve software modification instead of changing the design and manufacture of the hardware. Traditionally, there are four steps are required for a calibration, i.e. error modeling, measurement, parameter identification and compensation. The objective of this thesis is to propose a method for the kinematics analysis and error modeling of a newly developed hybrid redundant robot IWR (Intersector Welding Robot), which possesses ten degrees of freedom (DOF) where 6-DOF in parallel and additional 4-DOF in serial. In this article, the problem of kinematics modeling and error modeling of the proposed IWR robot are discussed. Based on the vector arithmetic method, the kinematics model and the sensitivity model of the end-effector subject to the structure parameters is derived and analyzed. The relations between the pose (position and orientation) accuracy and manufacturing tolerances, actuation errors, and connection errors are formulated. Computer simulation is performed to examine the validity and effectiveness of the proposed method.

Sensor Fusion of Proprioception, Force and Vision in Estimation and Robot

Sensor-based robot control allows manipulation in dynamic environments with uncertainties. Vision is a versatile low-cost sensory modality, but low sample rate, high sensor delay and uncertain measurements limit its usability, especially in strongly dynamic environments. Force is a complementary sensory modality allowing accurate measurements of local object shape when a tooltip is in contact with the object. In multimodal sensor fusion, several sensors measuring different modalities are combined to give a more accurate estimate of the environment. As force and vision are fundamentally different sensory modalities not sharing a common representation, combining the information from these sensors is not straightforward. In this thesis, methods for fusing proprioception, force and vision together are proposed. Making assumptions of object shape and modeling the uncertainties of the sensors, the measurements can be fused together in an extended Kalman filter. The fusion of force and visual measurements makes it possible to estimate the pose of a moving target with an end-effector mounted moving camera at high rate and accuracy. The proposed approach takes the latency of the vision system into account explicitly, to provide high sample rate estimates. The estimates also allow a smooth transition from vision-based motion control to force control. The velocity of the end-effector can be controlled by estimating the distance to the target by vision and determining the velocity profile giving rapid approach and minimal force overshoot. Experiments with a 5-degree-of-freedom parallel hydraulic manipulator and a 6-degree-of-freedom serial manipulator show that integration of several sensor modalities can increase the accuracy of the measurements significantly.

Success factors of customer and supplier master data system

Especially in global enterprises, key data is fragmented in multiple Enterprise Resource Planning (ERP) systems. Thus the data is inconsistent, fragmented and redundant across the various systems. Master Data Management (MDM) is a concept, which creates cross-references between customers, suppliers and business units, and enables corporate hierarchies and structures. The overall goal for MDM is the ability to create an enterprise-wide consistent data model, which enables analyzing and reporting customer and supplier data. The goal of the study was defining the properties and success factors of a master data system. The theoretical background was based on literature and the case consisted of enterprise specific needs and demands. The theoretical part presents the concept, background, and principles of MDM and then the phases of system planning and implementation project. Case consists of background, definition of as is situation, definition of project, evaluation criterions and concludes the key results of the thesis. In the end chapter Conclusions combines common principles with the results of the case. The case part ended up dividing important factors of the system in success factors, technical requirements and business benefits. To clarify the project and find funding for the project, business benefits have to be defined and the realization has to be monitored. The thesis found out six success factors for the MDM system: Well defined business case, data management and monitoring, data models and structures defined and maintained, customer and supplier data governance, delivery and quality, commitment, and continuous communication with business. Technical requirements emerged several times during the thesis and therefore those can’t be ignored in the project. Conclusions chapter goes through these factors on a general level. The success factors and technical requirements are related to the essentials of MDM: Governance, Action and Quality. This chapter could be used as guidance in a master data management project.

Ikääntyvät työelämässä. Päihittääkö nuoruus ja koulutus aikuisuuden ja kokemuksen?

The Ageing in Working Life. Do Adolescence and Schooling Beat Adulthood and Experience? This study examines the changes in the work and the work organisations of employees in the fields of health care and retail trade who have turned 45 and their experience of change. In addition, the question of how ageing employees experience their status in post-modern working life is explored. Attention is also focused on the choices and decisions connected with staying at work and retiring. These views are examined in relation to professions and professional cultures. Thematic interviews (N=98) were used to gather the material. The effects of the market liberalistic turn in welfare policy are clearly seen in the everyday work of the health care professions. These changes were examined from the point of view of managing by outcomes and quality assurance, multi-professional cooperation, flexibility in the division of labour, and the spread of market-like procedures. The discourse of those in involved retail trade was dominated by extremely tight global market competition and control of outcomes, and by the structural changes taking place in the retail trade sector. This change discourse was to a large extent a reaction to those changes in the functional environment which were experienced as negative and to the conflict between their own professional identity and professional ethics on the one hand, and their functional environment on the other. There were also obstacles connected with professional culture: defending one's own station and power, guarding the 'frontier', showed up in attitudes towards new management and organisation models or towards structural and functional reforms. The deep structures of professional culture and the mindset of the actors change much more slowly than the functional practices of organisations. For those in a supervisory position, the loss of power due to becoming part of a chain or because of the introduction of a team organisation model was not an easy thing to accept. The nurses and others in related fields felt that they were forced to do work that was below their level of training and professional skill. For sales personnel and those who did assisting work in health care, power and the possibility of having an influence were not so important, as long as they were able to do their work in their own way and were trusted. This view is often completely forgotten, for example, in various organisation models in which power and the possibility of having an influence entwined with power are taken for granted as being clearly positive and desired aspects of job satisfaction. Up to date professional skills were experienced as being important from the point of view of professional identity and self-worth. Thus, training can be understood as a moral obligation, which in turn is intertwined with professional ideology. In the rhetoric of adult education, an adult is expected to be an active player who will seek training again and again if working life so requires. The dark side of this ideology, which leads to feelings of guilt, was apparent in the thoughts of the respondents. Am I never good enough at my job; why must I continually strive for better, additional qualifications? The majority of the respondents evaluated their expertise as being at quite a high level. This self-confidence did not extend to applying for a job. Job recruitment was seen as a situation in which age discrimination reached its peak. The interviewees were unanimous about the idea that society favours the young. Especially among those in the retail trade sector, there was a feeling that it would be difficult, if not impossible, to find a new job of the same level or a permanent post if they were made redundant. Age discrimination was also apparent in the retail trade field in the form of older employees being retired against their will or transferred to other tasks. It was felt that ruthless forced retirement of older workers was part of the personnel policy of some organisations. The importance of one's outward appearance was connected with the theme of discrimination. This phenomenon is described using the concept of the double standard of ageing in feminist research. An ageing woman is relegated to an inferior position due to both her age and her sex. A culture that would both make possible and allow various types of choices regardless of age, which is described as being characteristic of the post-modern era, does not seem to be very topical in the practice of working life. It is important for employees that the management and the personnel policy that is being implemented makes them feel like both their contribution and they as individuals are appreciated, that their opinions are listened to and that they are noticed as persons. The interviewees hoped for gratitude and a concern for the well-being of employees that shows in everyday life. They valued training and activities aimed at maintaining their work ability, but thought that better coping at work and a pleasant working environment cannot be achieved through such measures as along as the foundation is 'in a mess'. Development of the quality of working life is the only thing that can improve job satisfaction and get people to remain in the work force longer than at present. There should be a sufficient number of properly trained employees at the work place. It was important to the respondents that they be able to stay on their job to the end with honour, since compromising with their own quality standards or acting contrary to their ideal self-image in terms of professional ethics would strike a blow to their professional self-esteem. They called for the development of various types of workplace flexibility, and felt that they have the right to a lightened workload and to early retirement. Early retirement was even seen as an altruistic deed: it would free up a place for younger workers. Thoughts of retirements were explained by familiar factors such as health and finances, life situation, the enticement of free-time, as well as by various factors related to work. It is very important to ageing employees that their work has meaningful content. The values related to self-fulfilment are felt to be of great importance, and if they cannot be realised at work, the respondents wanted more free time, either through retirement or in the form of flexibility in working life.

Supply chain costs of a small board lot: sheet cutting and logistics

Succeeding in small board lot (0-20 tons) deliveries, is not always prosperous and failures as well as extra costs compared to standard costs arise. Failure deliveries from converting plants to customer locations tie a lot of unwanted and unexpected costs. Extra costs are handled as quality costs and more precise, internal failure costs. These costs revolve from unsuccessful truck payloads, redundant warehousing or unfavorable routing as examples. Quality costs are becoming more and more important factor in company’s financial decision making. Actual, realized truck payload correlates with the extra costs occurring, so filling the truck payload all get-out well is a key to lower the extra costs. Case company in this study is Corporation A, business segment Boards. Boards have outsourced half of their converting in order to gain better customer service via flexibility, lead time reductions and logistics efficiency improvements. Examination period of the study is first two quarters of year 2008 and deliveries examined are from converters to the customer locations. In Corporation A’s case, the total loss in failure deliveries is hundreds of thousands of Euros during the examination period. So, the logistics goal of getting the right product to the right place and right time for the least cost, does not completely realize.