Analytic evaluation of three-phase short circuit demagnetization and hysteresis loss risk in rotor-surface-magnet Permanent-Magnet Synchronous Machines

Permanent magnet synchronous machines (PMSM) have become widely used in applications because of high efficiency compared to synchronous machines with exciting winding or to induction motors. This feature of PMSM is achieved through the using the permanent magnets (PM) as the main excitation source. The magnetic properties of the PM have significant influence on all the PMSM characteristics. Recent observations of the PM material properties when used in rotating machines revealed that in all PMSMs the magnets do not necessarily operate in the second quadrant of the demagnetization curve which makes the magnets prone to hysteresis losses. Moreover, still no good analytical approach has not been derived for the magnetic flux density distribution along the PM during the different short circuits faults. The main task of this thesis is to derive simple analytical tool which can predict magnetic flux density distribution along the rotor-surface mounted PM in two cases: during normal operating mode and in the worst moment of time from the PM’s point of view of the three phase symmetrical short circuit. The surface mounted PMSMs were selected because of their prevalence and relatively simple construction. The proposed model is based on the combination of two theories: the theory of the magnetic circuit and space vector theory. The comparison of the results in case of the normal operating mode obtained from finite element software with the results calculated with the proposed model shows good accuracy of model in the parts of the PM which are most of all prone to hysteresis losses. The comparison of the results for three phase symmetrical short circuit revealed significant inaccuracy of the proposed model compared with results from finite element software. The analysis of the inaccuracy reasons was provided. The impact on the model of the Carter factor theory and assumption that air have permeability of the PM were analyzed. The propositions for the further model development are presented.

Effects of Obesity and Weight Loss Following Bariatric Surgery on Brain Function, Structural Integrity and Metabolism

Obesity is one of the key challenges to health care system worldwide and its prevalence is estimated to rise to pandemic proportions. Numerous adverse health effects follow with increasing body weight, including increased risk of hypertension, diabetes, hypercholesterolemia, musculoskeletal pain and cancer. Current evidence suggests that obesity is associated with altered cerebral reward circuit functioning and decreased inhibitory control over appetitive food cues. Furthermore, obesity causes adverse shifts in metabolism and loss of structural integrity within the brain. Prior cross-sectional studies do not allow delineating which of these cerebral changes are recoverable after weight loss. We compared morbidly obese subjects with healthy controls to unravel brain changes associated with obesity. Bariatric surgery was used as an intervention to study which cerebral changes are recoverable after weight loss. In Study I we employed functional magnetic resonance imaging (fMRI) to detect the brain basis of volitional appetite control and its alterations in obesity. In Studies II-III we used diffusion tensor imaging (DTI) and voxel-based morphometry (VBM) to quantify the effects of obesity and the effects of weight loss on structural integrity of the brain. In study IV we used positron emission tomography (PET) with [18F]-FDG in fasting state and during euglycemic hyperinsulinemia to quantify effects of obesity and weight loss on brain glucose uptake. The fMRI experiment revealed that a fronto-parietal network is involved in volitional appetite control. Obese subjects had lower medial frontal and dorsal striatal brain activity during cognitive appetite control and increased functional connectivity within the appetite control circuit. Obese subjects had initially lower grey matter and white matter densities than healthy controls in VBM analysis and loss of integrity in white matter tracts as measured by DTI. They also had initially elevated glucose metabolism under insulin stimulation but not in fasting state. After the weight loss following bariatric surgery, obese individuals’ brain volumes recovered and the insulin-induced increase in glucose metabolism was attenuated. In conclusion, obesity is associated with altered brain function, coupled with loss of structural integrity and elevated glucose metabolism, which are likely signs of adverse health effects to the brain. These changes are reversed by weight loss after bariatric surgery, implicating that weight loss has a causal role on these adverse cerebral changes. Altogether these findings suggest that weight loss also promotes brain health.Key words: brain, obesity, bariatric surgery, appetite control, structural magnetic resonance

Quasiconformal mappings and inequalities involving special functions

This PhD thesis in Mathematics belongs to the field of Geometric Function Theory. The thesis consists of four original papers. The topic studied deals with quasiconformal mappings and their distortion theory in Euclidean n-dimensional spaces. This theory has its roots in the pioneering papers of F. W. Gehring and J. Väisälä published in the early 1960’s and it has been studied by many mathematicians thereafter. In the first paper we refine the known bounds for the so-called Mori constant and also estimate the distortion in the hyperbolic metric. The second paper deals with radial functions which are simple examples of quasiconformal mappings. These radial functions lead us to the study of the so-called p-angular distance which has been studied recently e.g. by L. Maligranda and S. Dragomir. In the third paper we study a class of functions of a real variable studied by P. Lindqvist in an influential paper. This leads one to study parametrized analogues of classical trigonometric and hyperbolic functions which for the parameter value p = 2 coincide with the classical functions. Gaussian hypergeometric functions have an important role in the study of these special functions. Several new inequalities and identities involving p-analogues of these functions are also given. In the fourth paper we study the generalized complete elliptic integrals, modular functions and some related functions. We find the upper and lower bounds of these functions, and those bounds are given in a simple form. This theory has a long history which goes back two centuries and includes names such as A. M. Legendre, C. Jacobi, C. F. Gauss. Modular functions also occur in the study of quasiconformal mappings. Conformal invariants, such as the modulus of a curve family, are often applied in quasiconformal mapping theory. The invariants can be sometimes expressed in terms of special conformal mappings. This fact explains why special functions often occur in this theory.

Mild Cognitive Impairment and Early Detection of Alzheimer`s Disease. A Positron Emission Tomography Study

Alzheimer`s disease (AD) is characterised neuropathologically by the presence of extracellular amyloid plaques, intraneuronal neurofibrillary tangles, and cerebral neuronal loss. The pathological changes in AD are believed to start even decades before clinical symptoms are detectable. AD gradually affects episodic memory, cognition, behaviour and the ability to perform everyday activities. Mild cognitive impairment (MCI) represents a transitional state between normal aging and dementia disorders, especially AD. The predictive accuracy of the current and commonly used MCI criteria devide this disorder into amnestic (aMCI) and non-amnestic (naMCI) MCI. It seems that many individuals with aMCI tend to convert to AD. However many MCI individuals will remain stable and some may even recover. At present, the principal drugs for the treatment of AD provide only symptomatic and palliative benefits. Safe and effective mechanism-based therapies are needed for this devastating neurodegenerative disease of later life. In conjunction with the development of new therapeutic drugs, tools for early detection of AD would be important. In future one of the challenges will be to detect at an early stage these MCI individuals who will convert to AD. Methods which can predict which MCI subjects will convert to AD will be much more important if the new drug candidates prove to have disease-arresting or even disease–slowing effects. These types of drugs are likely to have the best efficacy if administered in the early or even in the presymptomatic phase of the disease when the synaptic and neuronal loss has not become too widespread. There is no clinical method to determine with certainly which MCI individuals will progress to AD. However there are several methods which have been suggested as predictors of conversion to AD, e.g. increased [11C] PIB uptake, hippocampal atrophy in MRI, low CSF A beta 42 level, high CSF tau-protein level, apolipoprotein E (APOE) ε4 allele and impairment in episodic memory and executive functions. In the present study subjects with MCI appear to have significantly higher [¹¹C] PIB uptake vs healthy elderly in several brain areas including frontal cortex, the posterior cingulate, the parietal and lateral temporal cortices, putamen and caudate. Also results from this PET study indicate that over time, MCI subjects who display increased [¹¹C] PIB uptake appear to be significantly more likely to convert to AD than MCI subjects with negative [¹¹C] PIB retention. Also hippocampal atrophy seems to increase in MCI individuals clearly during the conversion to AD. In this study [¹¹C] PIB uptake increases early and changes relatively little during the AD process whereas there is progressive hippocampal atrophy during the disease. In addition to increased [¹¹C] PIB retention and hippocampal atrophy, the status of APOE ε4 allele might contribute to the conversion from MCI to AD.

Herpes simplex virus type 1 (HSV-1) pathogenesis and HSV gene therapy of experimental autoimmune encephalomyelitis

The aim of this thesis was to develop new herpes simplex virus (HSV) vectors for gene therapy of experimental autoimmune encephalomyelitis (EAE), the principal model of multiple sclerosis (MS), and to study the pathogenesis of wild-type HSV-1 and HSV-1 vectors in vivo. By introducing potential immunomodulatory factors into mice with EAE we strived to develop therapies and possibly find molecules improving recovery from EAE. We aimed at altering the immune response by inducing favorable Th2-type cytokines, thus shifting the immune response from a Th1- or a Th17-response. Our HSV vector expressing interleukin (IL)-5 modulated the cytokine responses, decreased inflammation and alleviated EAE. The use of a novel method, bacterial artificial chromosome (BAC), for engineering recombinant HSV facilitated the construction of a new vector expressing leukemia inhibitory factor (LIF). LIF is a neurotropic cytokine with broad functions in the central nervous system (CNS). LIF promotes oligodendrocyte maturation and decreases demyelination and oligodendrocyte loss. The BAC-derived HSV-LIF vector alleviated the clinical symptoms, induced a higher number of oligodendrocytes and modulated T cell responses. By administering HSV via different infection routes, e.g. peripherally via the nose or eye, or intracranially to the brain, the effect of the immune response on HSV spread at different points of the natural infection route was studied. The intranasal infection was an effective delivery route of HSV to the trigeminal ganglion and CNS, whereas corneal infection displayed limited spread. The corneal and intranasal infections induced different peripheral immune responses, which might explain the observed differences in viral spread.

Electronic Commerce - Advantages and Requirements through Supply Chain

Työ käsittelee Metso Paper Servicen varaosa- ja kulutusosatuotelinjojen mahdollisuuksia sähköiseen liiketoimintaan ulkoisten asiakkaiden kanssa sekä sähköisten transaktioiden vaikutuksia, etuja ja edellytyksiä. Työssä selvitetään Metson ja sen kymmenen kotimaisen asiakastehtaan myynti- ja ostoprosessin toiminta. Prosessimallin avulla arvioidaan valmiuksia sähköisiin transaktioihin nykyisessä myynti- ja ostotoiminnassa. Tarkastelu painottuu toimintoihin tarjontaketjun eri vaiheissa. Teknisiä näkökohtia käsitellään kokonaiskuvan luomiseksi. Lisäksi työssä arvioidaan muutoksia, joita sähköinen liiketoiminta aiheuttaisi. Haastatteluin tehdyssä tutkimuksessa kartoitetaan näkemyksiä sähköiseen liiketoimintaan erilaisilla organisaation tasoilla. Kokonaisnäkemys syntyy erilaisista näkökulmista sähköiseen kauppaan. Sähköiseen liiketoimintaan suhtaudutaan myönteisesti. Kokemuksia on kuitenkin vielä vähän. Vaikka hankkeita sähköisen liiketoiminnan lisäämiseksi on vireillä, yhtä tärkeää on parantaa valmiuksia tehostamalla paitsi informaatiovirtaa, myös materiaalivirtaa.

Identification and Management of Operational Risks in IT Organization of Financial Service Provider

Työn tavoitteena on tunnistaa toiminnallisia riskitekijöitä rahoituspalveluita tarjoavan yrityksen IT-organisaatiossa sekä löytää arkipäiväisiä keinoja hallita näitä riskejä. Työssä riskejä on myös tarkasteltu mahdollisen ulkoistuksen yhteydessä. Fuusiot ovat yleisiä rahoitusalan yrityksissä. Yhteenliittymien tuloksena yritysten IT-arkkitehtuuri voi olla monimutkainen ja kulttuurierot yrityksessä suuria. Synergia- ja mittakaavaetuja saadakseen yritys keskittää toimintojaan ja IT-ratkaisujaan. Riskien tunnistaminen on riskienhallintaprosessin tärkein vaihe. Tässä tutkimuksessa riskit ja riskitekijät tunnistettiin itsearvioinnin avulla kysymyssarjoja hyväksikäyttäen. Monet riskitekijät liittyivät sisäisen valvonnan ja seurannan puutteisiin. Myöhemmin näille riskeille pohdittiin työryhmässä käytännönläheisiä hallintakeinoja. Yritys voi siirtää tai jakaa IT -riskejä ulkoistamalla. Ulkoistaminen voi kuitenkin tuoda mukaan myös uusia riskitekijöitä. Ennen ulkoistamispäätöstä yrityksen sisäisten prosessien ja organisaation on oltava järjestyksessä, jotta sopimuksen kannattavuutta voidaan verrata luotettavasti saman palvelun tuottamiseen sisäisesti.

Avainhenkilöihin keskittyneen tietopääoman katoamisen riski ja sen hallinta pk-yrityksissä

Tutkielmassa selvitetään pienten ja keskisuurten yritysten avainhenkilöihin keskittyneen tietopääoman katoamisen riskiä ja pyritään löytämään keinoja riskin hallintaan. Pk-yrityksissä yrityksen kannalta kriittinen tieto on usein harvoihin henkilöihin keskittynyttä. Tällaisten avainhenkilöiden työpanoksen ja osaamisen menettäminen kokonaan saattaa olla yrityksen toiminnalle kohtalokasta. Väliaikainen osaamisen menettäminen voi myös vaikeuttaa toimintoja. Tietopääoman katoamisen riskin pienentäminen onnistuu joko avainhenkilön tiedon siirtämisellä toisiin henkilöihin tai huolehtimalla avainhenkilön työsuhteen mahdollisimman pitkästä jatkumisesta. Tiedon siirtämisen menetelmät riippuvat tiedon laadusta: onko se hiljaista vai eksplisiittistä. Avainhenkilön pysyvyyteen vaikuttaa yrityksen henkilöstöpolitiikka, jonka mukaisesti työntekijät saavat korvauksen työstään ja sitoutuvat yritykseen. Myös työntekijän työkyvystä huolehtiminen vaikuttaa tiedon pysymiseen yrityksen käytössä. Esimerkkiyrityksen haastatteluissa voidaan todeta yhtymäkohtia tutkimuksen muissa osissa käsiteltyihin tietojohtamisen ongelmiin.

CFD simulation of complex phenomena containing suspensions and flow throughporous media

There is an increasing reliance on computers to solve complex engineering problems. This is because computers, in addition to supporting the development and implementation of adequate and clear models, can especially minimize the financial support required. The ability of computers to perform complex calculations at high speed has enabled the creation of highly complex systems to model real-world phenomena. The complexity of the fluid dynamics problem makes it difficult or impossible to solve equations of an object in a flow exactly. Approximate solutions can be obtained by construction and measurement of prototypes placed in a flow, or by use of a numerical simulation. Since usage of prototypes can be prohibitively time-consuming and expensive, many have turned to simulations to provide insight during the engineering process. In this case the simulation setup and parameters can be altered much more easily than one could with a real-world experiment. The objective of this research work is to develop numerical models for different suspensions (fiber suspensions, blood flow through microvessels and branching geometries, and magnetic fluids), and also fluid flow through porous media. The models will have merit as a scientific tool and will also have practical application in industries. Most of the numerical simulations were done by the commercial software, Fluent, and user defined functions were added to apply a multiscale method and magnetic field. The results from simulation of fiber suspension can elucidate the physics behind the break up of a fiber floc, opening the possibility for developing a meaningful numerical model of the fiber flow. The simulation of blood movement from an arteriole through a venule via a capillary showed that the model based on VOF can successfully predict the deformation and flow of RBCs in an arteriole. Furthermore, the result corresponds to the experimental observation illustrates that the RBC is deformed during the movement. The concluding remarks presented, provide a correct methodology and a mathematical and numerical framework for the simulation of blood flows in branching. Analysis of ferrofluids simulations indicate that the magnetic Soret effect can be even higher than the conventional one and its strength depends on the strength of magnetic field, confirmed experimentally by Völker and Odenbach. It was also shown that when a magnetic field is perpendicular to the temperature gradient, there will be additional increase in the heat transfer compared to the cases where the magnetic field is parallel to the temperature gradient. In addition, the statistical evaluation (Taguchi technique) on magnetic fluids showed that the temperature and initial concentration of the magnetic phase exert the maximum and minimum contribution to the thermodiffusion, respectively. In the simulation of flow through porous media, dimensionless pressure drop was studied at different Reynolds numbers, based on pore permeability and interstitial fluid velocity. The obtained results agreed well with the correlation of Macdonald et al. (1979) for the range of actual flow Reynolds studied. Furthermore, calculated results for the dispersion coefficients in the cylinder geometry were found to be in agreement with those of Seymour and Callaghan.

Combined electromagnetic and thermal design platform for totally enclosed induction machines

The aim of the thesis is to design a suitable thermal model that can be used as a tool for constructing the TEFC squirrel cage induction machine in addition to the electromagnetic model. A lumped-parameter thermal model is developed. The related problems and aspects of implementation are discussed in details. Losses are calculated analytically and the loss values are used in the thermal model. The sensitivity analysis is introduced to determine the most critical parameters of the model.

Regulation of cell growth, death, and polarization by ERBB4

Regulation of cell growth, death, and polarization by ERBB4 ErbB4 is a member of the epidermal growth factor receptor (EGFR, ErbB) family. The other members are EGFR, ErbB2 and ErbB3. ErbB receptors are important regulators for example in cardiovascular, neural and breast development but control key cellular functions also in many adult tissues. Abnormal ErbB signaling has been shown to be involved in various illnesses such as cancers and heart diseases. Among the ErbBs, ErbB4 has been shown to have unique signaling characteristics. ErbB4 exists in four alternatively spliced isoforms that are expressed in a tissue-specific manner. Two of the isoforms can be cleaved by membrane proteases, resulting in release of soluble intracellular domains (ICD). Once released into the cytosol, the ICD is capable of translocating into the nucleus and participating in regulation of transcription. The functional differences and the tissue-specific expression patterns suggest isoformspecific roles for ErbB4 isoforms. However, the abilities of ErbB4 isoforms to differently regulate cellular functions were discovered only recently and are not well understood. This study aimed to determine the expression patterns of ErbB4 in normal and diseased tissue, and to define whether the cleavable and non-cleavable isoforms could regulate different target genes and therefore, cellular functions. In this study, a comprehensive ErbB4 expression pattern in several normal tissues, various cancers and non-neoplastic diseases was determined. In addition, the data demonstrated that the cleavable and non-cleavable ErbB4 isoforms could regulate different cellular functions and target genes. Finally, this study defined the cellular responses regulated by ErbB4 during kidney development.

Competence in intensive and critical care nursing - development of a basic assessment scale for graduating nursing students

Intensive and critical care nursing is a speciality in its own right and with its own nature within the nursing profession. This speciality poses its own demands for nursing competencies. Intensive and critical care nursing is focused on severely ill patients and their significant others. The patients are comprehensively cared for, constantly monitored and their vital functions are sustained artificially. The main goal is to win time to cure the cause of the patient’s situation or illness. The purpose of this empirical study was i) to describe and define competence and competence requirements in intensive and critical care nursing, ii) to develop a basic measurement scale for competence assessment in intensive and critical care nursing for graduating nursing students, and iii) to describe and evaluate graduating nursing students’ basic competence in intensive and critical care nursing by seeking the reference basis of self-evaluated basic competence in intensive and critical care nursing from ICU nurses. However, the main focus of this study was on the outcomes of nursing education in this nursing speciality. The study was carried out in different phases: basic exploration of competence (phase 1 and 2), instrumentation of competence (phase 3) and evaluation of competence (phase 4). Phase 1 (n=130) evaluated graduating nursing students’ basic biological and physiological knowledge and skills for working in intensive and critical care with Basic Knowledge Assessment Tool version 5 (BKAT-5, Toth 2012). Phase 2 focused on defining competence in intensive and critical care nursing with the help of literature review (n=45 empirical studies) as well as competence requirements in intensive and critical care nursing with the help of experts (n=45 experts) in a Delphi study. In phase 3 the scale Intensive and Critical Care Nursing Competence Scale (ICCN-CS) was developed and tested twice (pilot test 1: n=18 students and n=12 nurses; pilot test 2: n=56 students and n=54 nurses). Finally, in phase 4, graduating nursing students’ competence was evaluated with ICCN-CS and BKAT version 7 (Toth 2012). In order to develop a valid assessment scale of competence for graduating nursing students and to evaluate and establish the competence of graduating nursing students, empirical data were retrieved at the same time from both graduating nursing students (n=139) and ICU nurses (n=431). Competence can be divided into clinical and general professional competence. It can be defined as a specific knowledge base, skill base, attitude and value base and experience base of nursing and the personal base of an intensive and critical care nurse. Personal base was excluded in this self-evaluation based scale. The ICCN-CS-1 consists of 144 items (6 sum variables). Finally, it became evident that the experience base of competence is not a suitable sum variable in holistic intensive and critical care competence scale for graduating nursing students because of their minor experience in this special nursing area. ICCN-CS-1 is a reliable and tolerably valid scale for use among graduating nursing students and ICU nurses Among students, basic competence of intensive and critical care nursing was self-rated as good by 69%, as excellent by 25% and as moderate by 6%. However, graduating nursing students’ basic biological and physiological knowledge and skills for working in intensive and critical care were poor. The students rated their clinical and professional competence as good, and their knowledge base and skill base as moderate. They gave slightly higher ratings for their knowledge base than skill base. Differences in basic competence emerged between graduating nursing students and ICU nurses. The students’ self-ratings of both their basic competence and clinical and professional competence were significantly lower than the nurses’ ratings. The students’ self-ratings of their knowledge and skill base were also statistically significantly lower than nurses’ ratings. However, both groups reported the same attitude and value base, which was excellent. The strongest factor explaining students’ conception of their competence was their experience of autonomy in nursing. Conclusions: Competence in intensive and critical care nursing is a multidimensional concept. Basic competence in intensive and critical care nursing can be measured with self-evaluation based scale but alongside should be used an objective evaluation method. Graduating nursing students’ basic competence in intensive and critical care nursing is good but their knowledge and skill base are moderate. Especially the biological and physiological knowledge base is poor. Therefore in future in intensive and critical care nursing education should be focused on both strengthening students’ biological and physiological knowledge base and on strengthening their overall skill base. Practical implications are presented for nursing education, practice and administration. In future, research should focus on education methods and contents, mentoring of clinical practice and orientation programmes as well as further development of the scale.

Identification of Some Additional Loss Components in High-Power Low-Voltage Permanent Magnet Generators

Permanent magnet generators (PMG) represent the cutting edge technology in modern wind mills. The efficiency remains high (over 90%) at partial loads. To improve the machine efficiency even further, every aspect of machine losses has to be analyzed. Additional losses are often given as a certain percentage without providing any detailed information about the actual calculation process; meanwhile, there are many design-dependent losses that have an effect on the total amount of additional losses and that have to be taken into consideration. Additional losses are most often eddy current losses in different parts of the machine. These losses are usually difficult to calculate in the design process. In this doctoral thesis, some additional losses are identified and modeled. Further, suggestions on how to minimize the losses are given. Iron losses can differ significantly between the measured no-load values and the loss values under load. In addition, with embedded magnet rotors, the quadrature-axis armature reaction adds losses to the stator iron by manipulating the harmonic content of the flux. It was, therefore, re-evaluated that in salient pole machines, to minimize the losses and the loss difference between the no-load and load operation, the flux density has to be kept below 1.5 T in the stator yoke, which is the traditional guideline for machine designers. Eddy current losses may occur in the end-winding area and in the support structure of the machine, that is, in the finger plate and the clamping ring. With construction steel, these losses account for 0.08% of the input power of the machine. These losses can be reduced almost to zero by using nonmagnetic stainless steel. In addition, the machine housing may be subjected to eddy current losses if the flux density exceeds 1.5 T in the stator yoke. Winding losses can rise rapidly when high frequencies and 10–15 mm high conductors are used. In general, minimizing the winding losses is simple. For example, it can be done by dividing the conductor into transposed subconductors. However, this comes with the expense of an increase in the DC resistance. In the doctoral thesis, a new method is presented to minimize the winding losses by applying a litz wire with noninsulated strands. The construction is the same as in a normal litz wire but the insulation between the subconductors has been left out. The idea is that the connection is kept weak to prevent harmful eddy currents from flowing. Moreover, the analytical solution for calculating the AC resistance factor of the litz-wire is supplemented by including an end-winding resistance in the analytical solution. A simple measurement device is developed to measure the AC resistance in the windings. In the case of a litz-wire with originally noninsulated strands, vacuum pressure impregnation (VPI) is used to insulate the subconductors. In one of the two cases studied, the VPI affected the AC resistance factor, but in the other case, it did not have any effect. However, more research is needed to determine the effect of the VPI on litz-wire with noninsulated strands. An empirical model is developed to calculate the AC resistance factor of a single-layer formwound winding. The model includes the end-winding length and the number of strands and turns. The end winding includes the circulating current (eddy currents that are traveling through the whole winding between parallel strands) and the main current. The end-winding length also affects the total AC resistance factor.

Financial controlling and management in recovered paper joint ventures

The objective of this Master’s thesis is to examine financial functions, controlling and management in joint ventures of Manufacturing Corporation Oyj Recovered Paper business area. This case study investigated the current situation of financial functions and find out causes that have led the situation. Current situation of financial functions in joint ventures is variable. The most of the companies is outsourced at least some tasks. However, narrow reporting and problems in reliability are the biggest lack of financial controlling and management. The result of study consists of two parts: short-term and long-term improvement. Short-term improvement includes selected solution to outsource all routine financial tasks to new outsourcing partner and improve financial functions. Long-term improvements aim to create better controlling and management system to joint ventures. It is formed corporate governance and performance measurement. In this study it developed new Balanced Scorecard (BSC) for recovered paper joint ventures. Dimensions of BSC are quality, delivery (time), price and financial controlling and management. Earlier researched are showed problems in success of joint venture relationships. Similar results are obtained in this study. In future research, suitable of developed Balanced Scorecard for other industries could be studied