Welding time models for cost calculations in the early stages of the design process

It is generally accepted that between 70 and 80% of manufacturing costs can be attributed to design. Nevertheless, it is difficult for the designer to estimate manufacturing costs accurately, especially when alternative constructions are compared at the conceptual design phase, because of the lack of cost information and appropriate tools. In general, previous reports concerning optimisation of a welded structure have used the mass of the product as the basis for the cost comparison. However, it can easily be shown using a simple example that the use of product mass as the sole manufacturing cost estimator is unsatisfactory. This study describes a method of formulating welding time models for cost calculation, and presents the results of the models for particular sections, based on typical costs in Finland. This was achieved by collecting information concerning welded products from different companies. The data included 71 different welded assemblies taken from the mechanical engineering and construction industries. The welded assemblies contained in total 1 589 welded parts, 4 257 separate welds, and a total welded length of 3 188 metres. The data were modelled for statistical calculations, and models of welding time were derived by using linear regression analysis. Themodels were tested by using appropriate statistical methods, and were found to be accurate. General welding time models have been developed, valid for welding in Finland, as well as specific, more accurate models for particular companies. The models are presented in such a form that they can be used easily by a designer, enabling the cost calculation to be automated.

Design Process of Packaging Laboratory at Lappeenranta University of Technology

The layout design process of the packaging laboratory at Lappeenranta University of Technology is documented in this thesis. Layout planning methods are discussed in general. The systematic layout planning procedure is presented in more detail as it is utilised in the case of layout planning of the packaging laboratory. General demands for research laboratory are discussed both from the machine and product perspectives. The possibilities for commercial food processing in the laboratory are discussed from the point of view of foodstuff processing regulations and hygiene demands. The layout planning process is documented and different layout possibilities are presented. Different layout drafts are evaluated and one layout draft is developed to be the final layout of the packaging laboratory. Guideline for technical planning and implementation based on the final layout is given

Operational Knowledge in Process Design

Työn tarkoituksena on selvittää, miten käyttötietämystä hyödynnetään prosessisuunnittelussa. Tavoitteena on löytää keinoja parantaa käyttötietämyksen hallintaa suunnitteluprosessin aikana ja selvittää, vaikuttaako tämä prosessisuunnittelun laatuun.Prosessisuunnittelun laatua arvioidaan seitsemällä kriteerillä, jotka ovat investointikustannukset, käyttökustannukset, turvallisuus, ympäristövaikutukset, käytettävyys, innovatiivisuus ja aikataulu. Suunnitteluprosessi jaetaan kolmeen vaiheeseen: esisuunnitteluun, perussuunnitteluun ja detaljisuunnitteluun. Prosessisuunnittelua, investointiprojektia, prosessisuunnittelun laatukriteerejä, suunnitteluprosessin eri vaiheita ja käyttötietämyksen luokittelua tarkastellaan yleisesti. Työssä selvitettiin käyttötietämyksen hyödyntämistä Kemiralla. Aluksi muotoiltiin yleisiä väittämiä käyttötietämyksen hyödyntämisestä Kemiran ulkopuolisten eri alojen asiantuntijoiden haastattelujen perusteella. Tämän jälkeen Kemiran prosessisuunnittelijat arvioivat väittämiä. Arvioiden perusteella tehtiin johtopäätöksiä yleisesti käyttötietämyksen hyödyntämisestä prosessisuunnittelussa. Seuraavaksi haastateltiin kahdessa erityyppisessä case-projektissa mukana olleita henkilöitä ja muotoiltiin yleiset väittämät näihin projekteihin sopiviksi. Projekteissa mukana olleet henkilöt arvioivat väittämiä, ja näiden arvioiden perusteella projekteja vertailtiin keskenään. Lopussa esitetään johtopäätökset kaikkien väittämien arvioiden perusteella. Johtopäätöksenä voidaan todeta, että käyttötietämystä voidaan hyödyntää kaikissa suunnittelun vaiheissa, mutta paras hyöty saadaan perus- ja detaljisuunnittelussa. Käyttötietämyksellä voidaan vaikuttaa joihinkin prosessisuunnittelun laatukriteereihin, kuten esimerkiksi käytettävyyteen ja turvallisuuteen enemmän kuin muihin. Kemiralle suositellaan nykyisten tiedonhallintamenetelmien kehittämistä, jotta käyttötietämyksen saatavuus ja sen siirtäminen paranisi. Pr

Design of an Embedded Computer Board for Networking Applications

Tämä diplomityö tehtiin Convergens Oy:lle. Convergens on elektroniikan suunnittelutoimisto, joka on erikoistunut sulautettuihin järjestelmiin sekä tietoliikennetekniikkaan. Diplomityön tavoitteena oli suunnitella tietokonekortti tietoliikennesovelluksia varten asiakkaalle, jolta vaatimusmäärittelyt tulivat. Työ on rajattu koskemaan laitteen prototyypin suunnittelua. Työssä suunnitellaan pääasiassa WLAN-tukiaseman tietokone. Tukiasema onasennettavissa toimistoihin, varastoihin, kauppoihin sekä myös liikkuvaan ajoneuvoon. Suunnittelussa on otettu nämä asiat huomioon, ja laitteen akun pystyy lataamaan muun muassa auton akulla. Langattomat tekniikat ovat voimakkaasti yleistymässä, ja tämän työn tukiasema tarjoaakin varteenotettavan vaihtoehdon lukuisilla ominaisuuksillaan. Mukana on mm. GPS, Bluetooth sekä Ethernet-valmius. Langattomien tekniikoiden lisäksi myös sulautetut järjestelmät ovat voimakkaasti yleistymässä, ja nykyään mikroprosessoreita löytääkin lähesmistä vain. Tässä projektissa käytetty prosessori on nopeutensa puolesta kilpailukykyinen, ja siitä löytyy useita eri rajapintoja. Jatkossa tietokonekortille on myös tulossa WiMAX-tuki, joka lisää tukiaseman tulevaisuuden arvoa asiakkaalle. Projektiin valittu Freescalen MPC8321E-prosessori on PowerPC-arkkitehtuuriin perustuva ja juuri markkinoille ilmestynyt. Tämä toi mukanaan lisähaasteen, sillä kyseisestä prosessorista ei ollut vielä kaikkea tietoa saatavilla. Mekaniikka toi omat haasteensa mukanaan, sillä se rajoitti piirilevyn koonniin, että ylimääräistä piirilevytilaa ei juurikaan jäänyt. Tämän takia esimerkiksi DDR-muistit olivat haastavia reitittää, sillä muistivetojen on oltava melko samanpituisia keskenään. Käyttöjärjestelmänä projektissa käytetään Linuxia. Suunnittelu alkoi keväällä 2007 ja toimiva prototyyppi oli valmis alkusyksystä. Prototyypin testaus osoitti, että tietokonekortti kykenee täyttämään kaikki asiakkaan vaatimukset. Prototyypin testauksessa löytyneet viat ja optimoinnit on tarkoitus korjata tuotantomalliin, joten se antaa hyvän pohjan jatkosuunnittelua varten.

Conflict-based Method for Conceptual Process Synthesis

The changing business environment demands that chemical industrial processes be designed such that they enable the attainment of multi-objective requirements and the enhancement of innovativedesign activities. The requirements and key issues for conceptual process synthesis have changed and are no longer those of conventional process design; there is an increased emphasis on innovative research to develop new concepts, novel techniques and processes. A central issue, how to enhance the creativity of the design process, requires further research into methodologies. The thesis presentsa conflict-based methodology for conceptual process synthesis. The motivation of the work is to support decision-making in design and synthesis and to enhance the creativity of design activities. It deals with the multi-objective requirements and combinatorially complex nature of process synthesis. The work is carriedout based on a new concept and design paradigm adapted from Theory of InventiveProblem Solving methodology (TRIZ). TRIZ is claimed to be a `systematic creativity' framework thanks to its knowledge based and evolutionary-directed nature. The conflict concept, when applied to process synthesis, throws new lights on design problems and activities. The conflict model is proposed as a way of describing design problems and handling design information. The design tasks are represented as groups of conflicts and conflict table is built as the design tool. The general design paradigm is formulated to handle conflicts in both the early and detailed design stages. The methodology developed reflects the conflict nature of process design and synthesis. The method is implemented and verified through case studies of distillation system design, reactor/separator network design and waste minimization. Handling the various levels of conflicts evolve possible design alternatives in a systematic procedure which consists of establishing an efficient and compact solution space for the detailed design stage. The approach also provides the information to bridge the gap between the application of qualitative knowledge in the early stage and quantitative techniques in the detailed design stage. Enhancement of creativity is realized through the better understanding of the design problems gained from the conflict concept and in the improvement in engineering design practice via the systematic nature of the approach.

Studies on integrating kinematic design method with mechanical systems simulation techniques

Theultimate goal of any research in the mechanism/kinematic/design area may be called predictive design, ie the optimisation of mechanism proportions in the design stage without requiring extensive life and wear testing. This is an ambitious goal and can be realised through development and refinement of numerical (computational) technology in order to facilitate the design analysis and optimisation of complex mechanisms, mechanical components and systems. As a part of the systematic design methodology this thesis concentrates on kinematic synthesis (kinematic design and analysis) methods in the mechanism synthesis process. The main task of kinematic design is to find all possible solutions in the form of structural parameters to accomplish the desired requirements of motion. Main formulations of kinematic design can be broadly divided to exact synthesis and approximate synthesis formulations. The exact synthesis formulation is based in solving n linear or nonlinear equations in n variables and the solutions for the problem areget by adopting closed form classical or modern algebraic solution methods or using numerical solution methods based on the polynomial continuation or homotopy. The approximate synthesis formulations is based on minimising the approximation error by direct optimisation The main drawbacks of exact synthesis formulationare: (ia) limitations of number of design specifications and (iia) failure in handling design constraints- especially inequality constraints. The main drawbacks of approximate synthesis formulations are: (ib) it is difficult to choose a proper initial linkage and (iib) it is hard to find more than one solution. Recentformulations in solving the approximate synthesis problem adopts polynomial continuation providing several solutions, but it can not handle inequality const-raints. Based on the practical design needs the mixed exact-approximate position synthesis with two exact and an unlimited number of approximate positions has also been developed. The solutions space is presented as a ground pivot map but thepole between the exact positions cannot be selected as a ground pivot. In this thesis the exact synthesis problem of planar mechanism is solved by generating all possible solutions for the optimisation process ¿ including solutions in positive dimensional solution sets - within inequality constraints of structural parameters. Through the literature research it is first shown that the algebraic and numerical solution methods ¿ used in the research area of computational kinematics ¿ are capable of solving non-parametric algebraic systems of n equations inn variables and cannot handle the singularities associated with positive-dimensional solution sets. In this thesis the problem of positive-dimensional solutionsets is solved adopting the main principles from mathematical research area of algebraic geometry in solving parametric ( in the mathematical sense that all parameter values are considered ¿ including the degenerate cases ¿ for which the system is solvable ) algebraic systems of n equations and at least n+1 variables.Adopting the developed solution method in solving the dyadic equations in direct polynomial form in two- to three-precision-points it has been algebraically proved and numerically demonstrated that the map of the ground pivots is ambiguousand that the singularities associated with positive-dimensional solution sets can be solved. The positive-dimensional solution sets associated with the poles might contain physically meaningful solutions in the form of optimal defectfree mechanisms. Traditionally the mechanism optimisation of hydraulically driven boommechanisms is done at early state of the design process. This will result in optimal component design rather than optimal system level design. Modern mechanismoptimisation at system level demands integration of kinematic design methods with mechanical system simulation techniques. In this thesis a new kinematic design method for hydraulically driven boom mechanism is developed and integrated in mechanical system simulation techniques. The developed kinematic design method is based on the combinations of two-precision-point formulation and on optimisation ( with mathematical programming techniques or adopting optimisation methods based on probability and statistics ) of substructures using calculated criteria from the system level response of multidegree-of-freedom mechanisms. Eg. by adopting the mixed exact-approximate position synthesis in direct optimisation (using mathematical programming techniques) with two exact positions and an unlimitednumber of approximate positions the drawbacks of (ia)-(iib) has been cancelled.The design principles of the developed method are based on the design-tree -approach of the mechanical systems and the design method ¿ in principle ¿ is capable of capturing the interrelationship between kinematic and dynamic synthesis simultaneously when the developed kinematic design method is integrated with the mechanical system simulation techniques.

Cost information in engineering design -Potentials and limitations of activity-based costing

The purpose of this thesis is to analyse activity-based costing (ABC) and possible modified versions ofit in engineering design context. The design engineers need cost information attheir decision-making level and the cost information should also have a strong future orientation. These demands are high because traditional management accounting has concentrated on the direct actual costs of the products. However, cost accounting has progressed as ABC was introduced late 1980s and adopted widely bycompanies in the 1990s. The ABC has been a success, but it has gained also criticism. In some cases the ambitious ABC systems have become too complex to build,use and update. This study can be called an action-oriented case study with some normative features. In this thesis theoretical concepts are assessed and allowed to unfold gradually through interaction with data from three cases. The theoretical starting points are ABC and theory of engineering design process (chapter2). Concepts and research results from these theoretical approaches are summarized in two hypotheses (chapter 2.3). The hypotheses are analysed with two cases (chapter 3). After the two case analyses, the ABC part is extended to cover alsoother modern cost accounting methods, e.g. process costing and feature costing (chapter 4.1). The ideas from this second theoretical part are operationalized with the third case (chapter 4.2). The knowledge from the theory and three cases is summarized in the created framework (chapter 4.3). With the created frameworkit is possible to analyse ABC and its modifications in the engineering design context. The framework collects the factors that guide the choice of the costing method to be used in engineering design. It also illuminates the contents of various ABC-related costing methods. However, the framework needs to be further tested. On the basis of the three cases it can be said that ABC should be used cautiously when formulating cost information for engineering design. It is suitable when the manufacturing can be considered simple, or when the design engineers are not cost conscious, and in the beginning of the design process when doing adaptive or variant design. If the design engineers need cost information for the embodiment or detailed design, or if manufacturing can be considered complex, or when design engineers are cost conscious, the ABC has to be always evaluated critically.

Tuning the design procedures for laser processed microwave mechanics

This research has been focused at the development of a tuned systematic design methodology, which gives the best performance in a computer aided environment and utilises a cross-technological approach, specially tested with and for laser processed microwave mechanics. A tuned design process scheme is also presented. Because of the currently large production volumes of microwave and radio frequency mechanics even slight improvements of design methodologies or manufacturing technologies would give reasonable possibilities for cost reduction. The typical number of required iteration cycles could be reduced to one fifth of normal. The research area dealing with the methodologies is divided firstly into a function-oriented, a performance-oriented or a manufacturability-oriented product design. Alternatively various approaches can be developed for a customer-oriented, a quality-oriented, a cost-oriented or an organisation-oriented design. However, the real need for improvements is between these two extremes. This means that the effective methodology for the designers should not be too limited (like in the performance-oriented design) or too general (like in the organisation-oriented design), but it should, include the context of the design environment. This is the area where the current research is focused. To test the developed tuned design methodology for laser processing (TDMLP) and the tuned optimising algorithm for laser processing (TOLP), seven different industrial product applications for microwave mechanics have been designed, CAD-modelled and manufactured by using laser in small production series. To verify that the performance of these products meets the required level and to ensure the objectiveness ofthe results extensive laboratory tests were used for all designed prototypes. As an example a Ku-band horn antenna can be laser processed from steel in 2 minutes at the same time obtaining a comparable electrical performance of classical aluminium units or the residual resistance of a laser joint in steel could be limited to 72 milliohmia.

Mechanical Design of Hydraulic Vise

The general task of clamping devise is to connect the parts to the machining centers so that the work piece could be fixed on its position during the whole machining process. Additionally, the work piece should be clamped easily and rapidly by the machine users. The purpose of this Master’s thesis project was to develop a product design and find out the dimensioning of a hydraulic vise system for Astex Engineering OY, which was taking care of the general principles of product design and development during the design process. Throughout the process, the needs of manufacturing and assembling were taken into consideration for the machinability and minimization of the cost of manufacturing. The most critical component of the clamping devise was modeled by FEM for the issue of strength requirements. This 3D model was created with Solidworks and FEM-analysis was done with Cosmos software. As the result of this design work, a prototype of the hydraulic vise was manufactured for Astex Engineering OY and the practical test.

Conceptual Design of Embedded Weather Display

The objective of this thesis work is to describe the Conceptual Design process of an embedded electronic display device. The work presents the following sub processes: definition of device specifications, introduction to the technological alternatives for system components and their comparison, comparative photometric measurements of selected display panels, and the design and building of a functional concept prototype. This work focuses mainly on electronics design, albeit the mechanical issues and fields of the software architecture that significantly affect the decisions are also discussed when necessary. The VESA Flat Panel Display Measurement (FPDM) 2.0 Standard was applied to the appropriate extent into photometric measurements. The results were analyzed against the requirement standards of a customer-specific display development project. An Active Matrix LCD was selected as the display of concept prototype, but also the excellent visual characteristics of Active Matrix OLED technology were noted. Should the reliability of the OLED products be significantly improved in the future, utilizing such products in the described application must be reconsidered.

On Transmission System Design for Wireless Broadcasting

This thesis considers aspects related to the design and standardisation of transmission systems for wireless broadcasting, comprising terrestrial and mobile reception. The purpose is to identify which factors influence the technical decisions and what issues could be better considered in the design process in order to assess different use cases, service scenarios and end-user quality. Further, the necessity of cross-layer optimisation for efficient data transmission is emphasised and means to take this into consideration are suggested. The work is mainly related terrestrial and mobile digital video broadcasting systems but many of the findings can be generalised also to other transmission systems and design processes. The work has led to three main conclusions. First, it is discovered that there are no sufficiently accurate error criteria for measuring the subjective perceived audiovisual quality that could be utilised in transmission system design. Means for designing new error criteria for mobile TV (television) services are suggested and similar work related to other services is recommended. Second, it is suggested that in addition to commercial requirements there should be technical requirements setting the frame work for the design process of a new transmission system. The technical requirements should include the assessed reception conditions, technical quality of service and service functionalities. Reception conditions comprise radio channel models, receiver types and antenna types. Technical quality of service consists of bandwidth, timeliness and reliability. Of these, the thesis focuses on radio channel models and errorcriteria (reliability) as two of the most important design challenges and provides means to optimise transmission parameters based on these. Third, the thesis argues that the most favourable development for wireless broadcasting would be a single system suitable for all scenarios of wireless broadcasting. It is claimed that there are no major technical obstacles to achieve this and that the recently published second generation digital terrestrial television broadcasting system provides a good basis. The challenges and opportunities of a universal wireless broadcasting system are discussed mainly from technical but briefly also from commercial and regulatory aspect

Assessment of facilitators' design thinking

Meeting design is one of the most critical prerequisites of the success of facilitated meetings but how to achieve the success is not yet fully understood. This study presents a descriptive model of the design of technology supported meetings based on literature findings about the key factors contributing to the success of collaborative meetings, and linking these factors to the meeting design steps by exploring how facilitators consider the factors in practice in their design process. The empirical part includes a multiple-case study conducted among 12 facilitators. The case concentrates on the GSS laboratory at LUT, which has been working on facilitation and GSS for the last fifteen years. The study also includes ‘control’ cases from two comparable institutions. The results of this study highlight both the variances and commonalities among facilitators in how they design collaboration processes. The design thinking of facilitators of all levels of experience is found to be largely consistent wherefore the key design factors as well as their role across the design process can be outlined. Session goals, group composition, supporting technology, motivational aspects, physical constraints, and correct design practices were found to outline the key factors in design thinking. These factors are further categorized into three factor types of controllable, constraining, and guiding design factors, because the study findings indicate the factor type to have an effect on the factor’s importance in design. Furthermore, the order of considering these factors in the design process is outlined.

Antenna Design for Contactless IC Card Applications

Contactless integrated circuit cards are one form of application of radio frequency identification. They are used in applications such as access control, identification, and payment in public transport. The contactless IC cards are passive which means that both the data and the energy are transferred to the card without contact using inductive coupling. Antenna design and optimization of the design for contactless IC cards defined by ISO/IEC14443 is studied. The basic operation principles of contactless system are presented and the structure of contactless IC card is illustrated. The structure was divided between the contactless chip and the antenna. The operation of the antenna was covered in depth and the parameters affecting to the performance of the antenna were presented. Also the different antenna technologies and connection technologies were provided. The antenna design process with the parameters and the design tools isillustrated and optimization of the design is studied. To make the design process more ideal a target of development was discovered, which was the implementation of test application. The optimization of the antenna design was presented based on the optimization criteria defined in this study. The solution for the implementation of these criteria and the effect of each criterion was found. For enhancing the performance of the antenna a focus for future study was proposed.

Reducing Manufacturing Costs of the Screen Dryer’s Hot Section by Design

In this thesis, the purpose was to find the cost distribution of the screen dryer and the largest cost factors. The hot section of the screen dryer was revealed as the biggest cost factor, so composing new cost efficient solutions were directed to it. DFMA (Design for Manufacture and Assembly) was chosen to help the design process. DFMA is a product design strategy developed for taking manufacturing and assembly costs into account at the early stages of the design process. In the theory part of the thesis, other methods of economical design and tools needed for estimating manufacturing costs are introduced. In the empirical part, the hot section of the screen dryer was divided into sub-assemblies and their manufacturing costs were estimated. The design propositions were directed to the self-manufactured assemblies and parts. The new manufacturing costs were calculated for the developed propositions. Lastly, the most cost efficient solutions were summarized. The savings on the self-manufactured assemblies were about 40 %, which was about 13 % of the combined total costs of the hot section.