Transonic flow past on enlarged missile nose parts

Numerical computation of a viscid heat-conducting transonic flow over a generic commercial rocket profile with symmetric oversized nose part was carried out. It has been shown that at zero angle of attack for some free-streamvelocity value flow pattern loses its symmetry. This results in non-uniform pressure distribution on rocket surface in angle direction which may yield in additional oscillating stress on the rocket. Also it has been found that obtained non-symmetric flow patterns are stable for small velocity perturbations.

The Roles of Cultural, Functional and Value Diversity in Innovativeness and Learning

Tutkielman tavoite on tutkia kulttuurista, funktionaalista ja arvojen diversiteettiä, niiden suhdetta innovatiivisuuteen ja oppimiseen sekä tarjota keinoja diversiteetin johtamiseen. Tämän lisäksi selvitetään linjaesimiesten haastattelujen kautta miten diversiteetti case -organisaatiossa tällä hetkellä koetaan. Organisaation diversiteetin tämänhetkisen tilan tunnistamisen kautta voidaan esittää parannusehdotuksia diversiteetin hallintaan. Tutkimus- ja tiedonkeruumenetelmänä käytetään kvalitatiivista focus group haastattelumenetelmää. Tutkimuksessa saatiin selkeä kuva kulttuurisen, funktionaalisen ja arvojen diversiteetin merkityksistä organisaation innovatiivisuudelle ja oppimiselle sekä löydettiin keinoja näiden diversiteetin tyyppien johtamiseen. Tutkimuksen tärkeä löydös on se, että diversiteetti vaikuttaa positiivisesti organisaation innovatiivisuuteen kun sitä johdetaan tehokkaasti ja kun organisaatioympäristö tukee avointa keskustelua ja mielipiteiden jakamista. Case organisaation tämänhetkistä diversiteetin tilaa selvitettäessä havaittiin että ongelma organisaatiossa ei ole diversiteetin puute, vaan paremminkin se, ettei diversiteettia osata hyödyntää. Organisaatio ei tue erilaisten näkemysten ja mielipiteiden vapaata esittämistä jahyväksikäyttöä ja siksi diversiteetin hyödyntäminen on epätäydellistä. Haastatteluissa tärkeinä seikkoina diversiteetin hyödyntämisen parantamisessa nähtiin kulttuurin muuttaminen avoimempaan suuntaan ja johtajien esimiestaitojen parantaminen.

Patents in the Information and Communications Technology Sector - Development Trends, Problem Areas and Pressures for Change

The patent system was created for the purpose of promoting innovation by granting the inventors a legally defined right to exclude others in return for public disclosure. Today, patents are being applied and granted in greater numbers than ever, particularly in new areas such as biotechnology and information andcommunications technology (ICT), in which research and development (R&D) investments are also high. At the same time, the patent system has been heavily criticized. It has been claimed that it discourages rather than encourages the introduction of new products and processes, particularly in areas that develop quickly, lack one-product-one-patent correlation, and in which theemergence of patent thickets is characteristic. A further concern, which is particularly acute in the U.S., is the granting of so-called 'bad patents', i.e. patents that do not factually fulfil the patentability criteria. From the perspective of technology-intensive companies, patents could,irrespective of the above, be described as the most significant intellectual property right (IPR), having the potential of being used to protect products and processes from imitation, to limit competitors' freedom-to-operate, to provide such freedom to the company in question, and to exchange ideas with others. In fact, patents define the boundaries of ownership in relation to certain technologies. They may be sold or licensed on their ownor they may be components of all sorts of technology acquisition and licensing arrangements. Moreover, with the possibility of patenting business-method inventions in the U.S., patents are becoming increasingly important for companies basing their businesses on services. The value of patents is dependent on the value of the invention it claims, and how it is commercialized. Thus, most of them are worth very little, and most inventions are not worth patenting: it may be possible to protect them in other ways, and the costs of protection may exceed the benefits. Moreover, instead of making all inventions proprietary and seeking to appropriate as highreturns on investments as possible through patent enforcement, it is sometimes better to allow some of them to be disseminated freely in order to maximize market penetration. In fact, the ideology of openness is well established in the software sector, which has been the breeding ground for the open-source movement, for instance. Furthermore, industries, such as ICT, that benefit from network effects do not shun the idea of setting open standards or opening up their proprietary interfaces to allow everyone todesign products and services that are interoperable with theirs. The problem is that even though patents do not, strictly speaking, prevent access to protected technologies, they have the potential of doing so, and conflicts of interest are not rare. The primary aim of this dissertation is to increase understanding of the dynamics and controversies of the U.S. and European patent systems, with the focus on the ICT sector. The study consists of three parts. The first part introduces the research topic and the overall results of the dissertation. The second part comprises a publication in which academic, political, legal and business developments that concern software and business-method patents are investigated, and contentiousareas are identified. The third part examines the problems with patents and open standards both of which carry significant economic weight inthe ICT sector. Here, the focus is on so-called submarine patents, i.e. patentsthat remain unnoticed during the standardization process and then emerge after the standard has been set. The factors that contribute to the problems are documented and the practical and juridical options for alleviating them are assessed. In total, the dissertation provides a good overview of the challenges and pressures for change the patent system is facing,and of how these challenges are reflected in standard setting.

The role of Bluetooth technology in transforming the value network of ICT industry

Tutkimuksen tavoitteena oli selvittää miten Bluetooth-teknologia voi vaikuttaa ICT-alan arvoverkkoon ja alan toimijoiden rooleihin. Tutkimuksessa käytettiin kvalitatiivisia menetelmiä ja siinä oli piirteitä tulevaisuuden tutkimuksesta, koska myös eksploratiivisia menetelmiä käytettiin. Tutkimus perustui laajalti kirjallisuuteen ja artikkeleihin, joiden perusteella muodostettiin skenaarioita ICT-alan tulevaisuuden arvoverkosta. Tutkimus sisälsi myös empiirisen osion, jossa järjestettiin kaksi ryhmäkeskustelua, joissa alan toimijat keskustelivat muodostetuista skenaarioista sekä yleisemmin Bluetoothin vaikutuksista arvoverkkoon. Tutkimuksen mukaan ICT-alan arvoverkko tulevaisuudessa on rakenteeltaan strateginen arvoverkko, jota johtaa eri toimija erilaisissa markkinatilanteissa. Verkon strateginen keskus voi muuttua ajan kuluessa kun Bluetoothin sovelluskohteet lisääntyvät ja se voi vaihdella markkina-alueesta toiseen. Bluetooth luo uuden kommunikaatiokanavan nykyisten rinnalle ja se voi paikallisesti korvata nykyisten kanavien käytön tiedon siirrossa. Bluetooth voi synnyttää lukuisia uusia liiketoimintamahdollisuuksia ja sen avulla voidaan tuottaa lisäarvopalveluita. Suurimpien muutosten voidaan olettaa koskevan teleoperaattoreiden ja sisällöntuottajien liiketoimintaa.

Digital printing delivering value to the value network: CASE: STORA ENSO OYJ

Tutkielman tavoitteena oli tutkia, millaista arvoa digitaalinen painatusmenetelmä tuo yrityksen arvoverkostoon. Teoriaosassa tavoite oli rakentaa digitaalipainatuksen arvoverkostoa tutkien kirjallisuutta liittyen arvoketju- ja arvoverkostoajatteluun. Myös aiemmat tutkimukset ja kirjallisuus liittyen digitaalipainatukseen rakensivat osaltaan teoreettisen viitekehyksen muodostumista. Aiemmat tutkimukset digitaalisen painomenetelmän mahdollisuuksista ovat hyvin tekniikkapainotteisia, siksi tämä tutkimus liittyy enemmän kaupallisiin mahdollisuuksiin. Empiirinen osio tutkimuksesta tehtiin kvalitatiivisena case -tutkimuksena, johon sisältyi yksi alayksikkö. Eli tutkittiin yhtä casea, jossa oli kaksi osapuolta. Tutkielma liittyy kiinteästi Stora Enson ja Valion väliseen digipainatus-projektiin, joka käynnistettiin helmikuussa 2001. Tutkielman teemahaastatteluihin valittiin henkilöt tästä projektiryhmästä. Projektiryhmän mielipiteitä ja havaintoja hyödyntäen pyrittiin löytämään tukea ja eroavaisuuksia teoriaosan muodostamaan viitekehykseen ja informaatioon. Empiirinen osuus tuki teoriaosassa esittämiä väittämiä hyvin, mutta myös muutamia uusia havaintoja esiintyi. Tutkimusongelmaan löydettiin monia vastauksia: digitaalipainatus luo arvoa yrityksen jakeluketjuun vähentämällä varastoja ja nopeuttamalla toimituksia. Jäätelöpakkausten markkinointi on aivan uuden haasteen edessä, koska mahdollisuudet kasvavat digitaalipainatuksen myötä huomattavasti. Kartongin valmistajalle arvo tulee parempien tuotteiden kautta, joista saa myös paremman tuoton. Digitaalipainatuksen arvoverkostossa tulee tapahtumaan muutoksia jatkossa, eri osapuolten roolit saattavat muuttua radikaalisti. Kuka hoitaa painatusta ja miten?

Osakeperusteinen palkitseminen: maksuttoman osakkeen hyödyntäminen kannustinjärjestelmissä

Tutkielman tavoitteena on selvittää osakeyhtiön palkitsemisjärjestelmiin liittyviä kysymyksiä päämies–agenttisuhteiden ja osakeyhtiöoikeudellisten periaatteiden kautta. Tutkielmassa selvitetään, kuinka maksuttomia osakkeita voidaan hyödyntää julkisen osakeyhtiön palkitsemisjärjestelmissä ja mitä haasteita ja mahdollisuuksia niiden käyttöön liittyy. Tutkimusmetodi työssä on lainopillinen ja aihetta lähestytään luontevasti kauppatieteellisen ja oikeustieteellisen näkökulman yhdistävän oikeustaloustieteen kautta. Ensisijaisena aineistona tutkielmassa käytetään voimassaolevaa lainsäädäntöä valmisteluaineistoineen ja näkökulmaa syvennetään aiemmin voimassa olleen lainsäädännön tarkastelulla. Toissijaisena aineistona tutkielmassa käytetään sekä eri asiantuntijoiden oikeudellista kirjallisuutta että palkitsemisen asiantuntijoiden laatimaa kirjallisuutta Suomesta ja muista länsimaista. Teoreettista työtä on syvennetty asiantuntijahaastattelulla ja yhtiöiden sijoittajatiedosta saatavalla informaatiolla. Merkittävin osakeyhtiön johdon ja yhtiön välisen suhteen tehokkuutta alentava seikka on päämies–agenttisuhteen valvontaongelma. Tämä liittyy päämies - agenttisuhteeseen, joka ilmenee negatiivisesti yhtiön ja yhtiön johdon intressien ristiriitatilanteissa. Valvontaongelma voi aiheuttaa ylimääräisiä transaktiokustannuksia ja tämä näkyy yhtiön toiminnan tehokkuuden laskemisena. Päämies–agenttisuhteen ratkaisuna lainsäädäntö ja erilaiset valvonnan keinot ovat tehottomia ja nykyisen yhtiöoikeudellisen ajattelun vastaisia. Tehokkaimmin valvontaongelma saadaan ratkaistua erilaisin kannustimin tapahtuvalla johdon ohjauksella. Osakesidonnainen palkitseminen on suosituin johdon ja yhtiön intressien yhdistämisen keino. Osakesidonnainen palkitseminen on parhaimmillaan eri osapuolien näkökulmasta sitouttavaa ja kannustavaa mutta osakepalkitsemisen käyttöön liittyy myös riskejä. Eräs keskeisistä yhtiöoikeudellisista periaatteista on yhdenvertaisuus, jota saatetaan loukata eri palkitsemisjärjestelmiä käytettäessä. Varojen jakoon ja järjestelmien rahoitukseen liittyy niin ikään riskejä, jotka saattavat vaarantaa järjestelmän onnistumisen. Liian avokätiset palkkiojärjestelmät taas saattavat aiheuttaa yhtiön eri sidosryhmien piirissä tyytymättömyyttä joka taas alentaa järjestelmän tehokkuutta. Yhtiön johto vastaa yhtiön strategian toteutumisesta ja linjaa Corporate Governance käytännön mukaisesti johdon palkitsemisen tavat. Yhtiön johto on kuitenkin päätöksistään vastuussa yhtiön residuaalioikeuden omaaville päämiehille, eli osakkeenomistajille. Vaikka yhtiön johto vastaa viime kädessä yhtiön toiminnasta, sen on huomioitava toiminnassaan yhtiön toiminnan tarkoitus ja sitä kautta yksittäisen osakkeenomistajan etu. Vaikka osakeyhtiössä toteutettaisiin enemmistöomistajan valitsemaa toimintalinjaa, osakeyhtiön yhdenvertaisuusperiaate korostaa juuri vähemmistöosakkeenomistajan asemaa. Johdon fidusiaaristen velvoitteiden voidaankin nähdä korostuvan johdon suhteessa vähemmistöosakkeenomistajaan. Tämä on huomioitava myös palkitsemisjärjestelmissä. Johdon palkitsemisjärjestelmien suunnittelussa ja toteutuksessa on suunnattava keskeinen huomio sen tavoitteiden toteutumiseen, eli yksittäisen osakkeenomistajan omistuksen arvon kasvattamiseen pidemmällä aikavälillä, pitäen huolta osakeyhtiön kantavista periaatteista.

Separation of Gas Bubbles from Circulation Waters and Pulp Suspensions in Open Channel Flow

The objective of this thesis was to study the removal of gases from paper mill circulation waters experimentally and to provide data for CFD modeling. Flow and bubble size measurements were carried out in a laboratory scale open gas separation channel. Particle Image Velocimetry (PIV) technique was used to measure the gas and liquid flow fields, while bubble size measurements were conducted using digital imaging technique with back light illumination. Samples of paper machine waters as well as a model solution were used for the experiments. The PIV results show that the gas bubbles near the feed position have the tendency to escape from the circulation channel at a faster rate than those bubbles which are further away from the feed position. This was due to an increased rate of bubble coalescence as a result of the relatively larger bubbles near the feed position. Moreover, a close similarity between the measured slip velocities of the paper mill waters and that of literature values was obtained. It was found that due to dilution of paper mill waters, the observed average bubble size was considerably large as compared to the average bubble sizes in real industrial pulp suspension and circulation waters. Among the studied solutions, the model solution has the highest average drag coefficient value due to its relatively high viscosity. The results were compared to a 2D steady sate CFD simulation model. A standard Euler-Euler k-ε turbulence model was used in the simulations. The channel free surface was modeled as a degassing boundary. From the drag models used in the simulations, the Grace drag model gave velocity fields closest to the experimental values. In general, the results obtained from experiments and CFD simulations are in good qualitative agreement.

Vibration free machining tools

Appearance of the vibration is the very important problem in long tool turning and milling. Current solutions of minimizing vibrations provided by different tool suppliers are very expensive. This Master’s Thesis is presenting the new type of vibration free machining tools produced by Konepaja ASTEX Gear Oy that have cheaper production costs compare to competitors’ products. Vibration problems in machining and their today’s solutions are analyzed in this work. The new vibration damping invention is presented and described. Moreover, the production, laboratory experimental modal analysis and practical testing of the new vibration free prototypes are observed and analyzed on the pages of this Thesis. Based on the testing results the new invention is acknowledged to be successful and approved for further studies and developments.

The value of digitalization of services in the new service development

The purpose of this thesis is to study factors that have an impact on the company’s capabilities to identify and analyze the value of digitalization of services during the early stages of service development process and evaluate them from the perspective of a case company. The research problem was defined: “How digitalization of services affects delivering the services of the future?” The research method of this thesis was based on the qualitative case study which aimed to study both company’s and customer’s set of values. The study included a literature review and a development study. The empirical research part consisted of analyzing three existing services, specifying a new digital service concept and its feasibility analysis as part of a business requirement phase. To understand the set of values, 10 stakeholder interviews were conducted and earlier customer surveys were utilized, and additionally, a number of meetings were conducted with the case company representatives to develop service concept, and evaluate the findings. The impact of the early stages of service development process discovered to reflect directly in the capabilities of the case company to identify and create customer value were related to the themes presented in the literature review. In order to specify the value achieved from the digitalization the following areas of strategic background elements were deepened during the study: Innovations, customer understanding and business service. Based on the findings, the study aims to enhance the case company’s capability to identify and evaluate the impact of the digitalization in delivering services of the future. Recognizing the value of digital service before the beginning of the development project is important to the businesses of both customer and provider. By exploring the various levels of digitalization one can get the overall picture of the value gained from utilizing digital opportunities. From the development perspective, the process of reviewing and discovering the most promising opportunities and solutions is the key step in order to deliver superior services. Ultimately, a company should understand the value outcome determination of the individual services as well as their digital counterparts.

Production of Mg(OH)2 from Mg-silicate rock for CO2 mineral sequestration

Sequestration of carbon dioxide in mineral rocks, also known as CO2 Capture and Mineralization (CCM), is considered to have a huge potential in stabilizing anthropogenic CO2 emissions. One of the CCM routes is the ex situ indirect gas/sold carbonation of reactive materials, such as Mg(OH)2, produced from abundantly available Mg-silicate rocks. The gas/solid carbonation method is intensively researched at Åbo Akademi University (ÅAU ), Finland because it is energetically attractive and utilizes the exothermic chemistry of Mg(OH)2 carbonation. In this thesis, a method for producing Mg(OH)2 from Mg-silicate rocks for CCM was investigated, and the process efficiency, energy and environmental impact assessed. The Mg(OH)2 process studied here was first proposed in 2008 in a Master’s Thesis by the author. At that time the process was applied to only one Mg-silicate rock (Finnish serpentinite from the Hitura nickel mine site of Finn Nickel) and the optimum process conversions, energy and environmental performance were not known. Producing Mg(OH)2 from Mg-silicate rocks involves a two-staged process of Mg extraction and Mg(OH)2 precipitation. The first stage extracts Mg and other cations by reacting pulverized serpentinite or olivine rocks with ammonium sulfate (AS) salt at 400 - 550 oC (preferably < 450 oC). In the second stage, ammonia solution reacts with the cations (extracted from the first stage after they are leached in water) to form mainly FeOOH, high purity Mg(OH)2 and aqueous (dissolved) AS. The Mg(OH)2 process described here is closed loop in nature; gaseous ammonia and water vapour are produced from the extraction stage, recovered and used as reagent for the precipitation stage. The AS reagent is thereafter recovered after the precipitation stage. The Mg extraction stage, being the conversion-determining and the most energy-intensive step of the entire CCM process chain, received a prominent attention in this study. The extraction behavior and reactivity of different rocks types (serpentinite and olivine rocks) from different locations worldwide (Australia, Finland, Lithuania, Norway and Portugal) was tested. Also, parametric evaluation was carried out to determine the optimal reaction temperature, time and chemical reagent (AS). Effects of reactor types and configuration, mixing and scale-up possibilities were also studied. The Mg(OH)2 produced can be used to convert CO2 to thermodynamically stable and environmentally benign magnesium carbonate. Therefore, the process energy and life cycle environmental performance of the ÅAU CCM technique that first produces Mg(OH)2 and the carbonates in a pressurized fluidized bed (FB) were assessed. The life cycle energy and environmental assessment approach applied in this thesis is motivated by the fact that the CCM technology should in itself offer a solution to what is both an energy and environmental problem. Results obtained in this study show that different Mg-silicate rocks react differently; olivine rocks being far less reactive than serpentinite rocks. In summary, the reactivity of Mg-silicate rocks is a function of both the chemical and physical properties of rocks. Reaction temperature and time remain important parameters to consider in process design and operation. Heat transfer properties of the reactor determine the temperature at which maximum Mg extraction is obtained. Also, an increase in reaction temperature leads to an increase in the extent of extraction, reaching a maximum yield at different temperatures depending on the reaction time. Process energy requirement for producing Mg(OH)2 from a hypothetical case of an iron-free serpentine rock is 3.62 GJ/t-CO2. This value can increase by 16 - 68% depending on the type of iron compound (FeO, Fe2O3 or Fe3O4) in the mineral. This suggests that the benefit from the potential use of FeOOH as an iron ore feedstock in iron and steelmaking should be determined by considering the energy, cost and emissions associated with the FeOOH by-product. AS recovery through crystallization is the second most energy intensive unit operation after the extraction reaction. However, the choice of mechanical vapor recompression (MVR) over the “simple evaporation” crystallization method has a potential energy savings of 15.2 GJ/t-CO2 (84 % savings). Integrating the Mg(OH)2 production method and the gas/solid carbonation process could provide up to an 25% energy offset to the CCM process energy requirements. Life cycle inventory assessment (LCIA) results show that for every ton of CO2 mineralized, the ÅAU CCM process avoids 430 - 480 kg CO2. The Mg(OH)2 process studied in this thesis has many promising features. Even at the current high energy and environmental burden, producing Mg(OH)2 from Mg-silicates can play a significant role in advancing CCM processes. However, dedicated future research and development (R&D) have potential to significantly improve the Mg(OH)2 process performance.

Libyan breast cancer: Health services and biology. Diagnosis delay and prognostic value of DNA pploidy, S-phase fraction, and Ki-67 and Bcl-2 immunohistochemistry

The aim of this study was to investigate the diagnosis delay and its impact on the stage of disease. The study also evaluated a nuclear DNA content, immunohistochemical expression of Ki-67 and bcl-2, and the correlation of these biological features with the clinicopathological features and patient outcome. 200 Libyan women, diagnosed during 2008–2009 were interviewed about the period from the first symptoms to the final histological diagnosis of breast cancer. Also retrospective preclinical and clinical data were collected from medical records on a form (questionnaire) in association with the interview. Tumor material of the patients was collected and nuclear DNA content analysed using DNA image cytometry. The expression of Ki-67 and bcl-2 were assessed using immunohistochemistry (IHC). The studies described in this thesis show that the median of diagnosis time for women with breast cancer was 7.5 months and 56% of patients were diagnosed within a period longer than 6 months. Inappropriate reassurance that the lump was benign was an important reason for prolongation of the diagnosis time. Diagnosis delay was also associated with initial breast symptom(s) that did not include a lump, old age, illiteracy, and history of benign fibrocystic disease. The patients who showed diagnosis delay had bigger tumour size (p<0.0001), positive lymph nodes (p<0.0001), and high incidence of late clinical stages (p<0.0001). Biologically, 82.7% of tumors were aneuploid and 17.3% were diploid. The median SPF of tumors was 11% while the median positivity of Ki-67 was 27.5%. High Ki-67 expression was found in 76% of patients, and high SPF values in 56% of patients. Positive bcl-2 expression was found in 62.4% of tumors. 72.2% of the bcl-2 positive samples were ER-positive. Patients who had tumor with DNA aneuploidy, high proliferative activity and negative bcl-2 expression were associated with a high grade of malignancy and short survival. The SPF value is useful cell proliferation marker in assessing prognosis, and the decision cut point of 11% for SPF in the Libyan material was clearly significant (p<0.0001). Bcl-2 is a powerful prognosticator and an independent predictor of breast cancer outcome in the Libyan material (p<0.0001). Libyan breast cancer was investigated in these studies from two different aspects: health services and biology. The results show that diagnosis delay is a very serious problem in Libya and is associated with complex interactions between many factors leading to advanced stages, and potentially to high mortality. Cytometric DNA variables, proliferative markers (Ki-67 and SPF), and oncoprotein bcl-2 negativity reflect the aggressive behavior of Libyan breast cancer and could be used with traditional factors to predict the outcome of individual patients, and to select appropriate therapy.

Power semiconductor nonlinearities in active du/dt output filtering

This doctoral thesis introduces an improved control principle for active du/dt output filtering in variable-speed AC drives, together with performance comparisons with previous filtering methods. The effects of power semiconductor nonlinearities on the output filtering performance are investigated. The nonlinearities include the timing deviation and the voltage pulse waveform distortion in the variable-speed AC drive output bridge. Active du/dt output filtering (ADUDT) is a method to mitigate motor overvoltages in variable-speed AC drives with long motor cables. It is a quite recent addition to the du/dt reduction methods available. This thesis improves on the existing control method for the filter, and concentrates on the lowvoltage (below 1 kV AC) two-level voltage-source inverter implementation of the method. The ADUDT uses narrow voltage pulses having a duration in the order of a microsecond from an IGBT (insulated gate bipolar transistor) inverter to control the output voltage of a tuned LC filter circuit. The filter output voltage has thus increased slope transition times at the rising and falling edges, with an opportunity of no overshoot. The effect of the longer slope transition times is a reduction in the du/dt of the voltage fed to the motor cable. Lower du/dt values result in a reduction in the overvoltage effects on the motor terminals. Compared with traditional output filtering methods to accomplish this task, the active du/dt filtering provides lower inductance values and a smaller physical size of the filter itself. The filter circuit weight can also be reduced. However, the power semiconductor nonlinearities skew the filter control pulse pattern, resulting in control deviation. This deviation introduces unwanted overshoot and resonance in the filter. The controlmethod proposed in this thesis is able to directly compensate for the dead time-induced zero-current clamping (ZCC) effect in the pulse pattern. It gives more flexibility to the pattern structure, which could help in the timing deviation compensation design. Previous studies have shown that when a motor load current flows in the filter circuit and the inverter, the phase leg blanking times distort the voltage pulse sequence fed to the filter input. These blanking times are caused by excessively large dead time values between the IGBT control pulses. Moreover, the various switching timing distortions, present in realworld electronics when operating with a microsecond timescale, bring additional skew to the control. Left uncompensated, this results in distortion of the filter input voltage and a filter self-induced overvoltage in the form of an overshoot. This overshoot adds to the voltage appearing at the motor terminals, thus increasing the transient voltage amplitude at the motor. This doctoral thesis investigates the magnitude of such timing deviation effects. If the motor load current is left uncompensated in the control, the filter output voltage can overshoot up to double the input voltage amplitude. IGBT nonlinearities were observed to cause a smaller overshoot, in the order of 30%. This thesis introduces an improved ADUDT control method that is able to compensate for phase leg blanking times, giving flexibility to the pulse pattern structure and dead times. The control method is still sensitive to timing deviations, and their effect is investigated. A simple approach of using a fixed delay compensation value was tried in the test setup measurements. The ADUDT method with the new control algorithm was found to work in an actual motor drive application. Judging by the simulation results, with the delay compensation, the method should ultimately enable an output voltage performance and a du/dt reduction that are free from residual overshoot effects. The proposed control algorithm is not strictly required for successful ADUDT operation: It is possible to precalculate the pulse patterns by iteration and then for instance store them into a look-up table inside the control electronics. Rather, the newly developed control method is a mathematical tool for solving the ADUDT control pulses. It does not contain the timing deviation compensation (from the logic-level command to the phase leg output voltage), and as such is not able to remove the timing deviation effects that cause error and overshoot in the filter. When the timing deviation compensation has to be tuned-in in the control pattern, the precalculated iteration method could prove simpler and equally good (or even better) compared with the mathematical solution with a separate timing compensation module. One of the key findings in this thesis is the conclusion that the correctness of the pulse pattern structure, in the sense of ZCC and predicted pulse timings, cannot be separated from the timing deviations. The usefulness of the correctly calculated pattern is reduced by the voltage edge timing errors. The doctoral thesis provides an introductory background chapter on variable-speed AC drives and the problem of motor overvoltages and takes a look at traditional solutions for overvoltage mitigation. Previous results related to the active du/dt filtering are discussed. The basic operation principle and design of the filter have been studied previously. The effect of load current in the filter and the basic idea of compensation have been presented in the past. However, there was no direct way of including the dead time in the control (except for solving the pulse pattern manually by iteration), and the magnitude of nonlinearity effects had not been investigated. The enhanced control principle with the dead time handling capability and a case study of the test setup timing deviations are the main contributions of this doctoral thesis. The simulation and experimental setup results show that the proposed control method can be used in an actual drive. Loss measurements and a comparison of active du/dt output filtering with traditional output filtering methods are also presented in the work. Two different ADUDT filter designs are included, with ferrite core and air core inductors. Other filters included in the tests were a passive du/dtfilter and a passive sine filter. The loss measurements incorporated a silicon carbide diode-equipped IGBT module, and the results show lower losses with these new device technologies. The new control principle was measured in a 43 A load current motor drive system and was able to bring the filter output peak voltage from 980 V (the previous control principle) down to 680 V in a 540 V average DC link voltage variable-speed drive. A 200 m motor cable was used, and the filter losses for the active du/dt methods were 111W–126 W versus 184 W for the passive du/dt. In terms of inverter and filter losses, the active du/dt filtering method had a 1.82-fold increase in losses compared with an all-passive traditional du/dt output filter. The filter mass with the active du/dt method was 17% (2.4 kg, air-core inductors) compared with 14 kg of the passive du/dt method filter. Silicon carbide freewheeling diodes were found to reduce the inverter losses in the active du/dt filtering by 18% compared with the same IGBT module with silicon diodes. For a 200 m cable length, the average peak voltage at the motor terminals was 1050 V with no filter, 960 V for the all-passive du/dt filter, and 700 V for the active du/dt filtering applying the new control principle.

Value co-creation in gaming the industry: A qualitative research on virtual discussion forums

This study discusses the procedures of value co-creation that persist in gaming industry. The purpose of this study was to identify the procedures that persist in current video gaming industry which answers the main research problem how value is co-created in video gaming industry followed by three sub questions: (i) What is value co-creation in gaming industry? (ii) Who participates in value co-creation in gaming industry? (iii) What are the procedures that are involved in value co-creation in gaming industry? The theoretical background of the study consists of literature relating to the theory of marketing i.e., notion of value, conventional understanding of value creation, value chain, co-creation approach, co-production approach. The research adopted qualitative research approach. As a platform of relationship researcher used web 2.0 tool interface. Data were collected from the social networks and netnography method was applied for analyzing them. Findings show that customer and company both co-create optimum level of value while they interact with each other and within the customers as well. However mostly the C2C interaction, discussions and dialogues threads that emerged around the main discussion facilitated to co-create value. In this manner, companies require exploiting and further motivating, developing and supporting the interactions between customers participating in value creation. Hierarchy of value co-creation processes is the result derived from the identified challenges of value co-creation approach and discussion forums data analysis. Overall three general sets and seven topics were found that explored the phenomenon of customer to customer (C2C) and business to customer (B2C) interaction/debating for value co-creation through user generated contents. These topics describe how gamer contributes and interacts in co-creating value along with companies. A methodical quest in current research literature acknowledged numerous evolving flows of value in this study. These are general management perspective, new product development and innovation, virtual customer environment, service science and service dominant logic. Overall the topics deliver various realistic and conceptual implications for using and handling gamers in social networks for augmenting customers’ value co-creation process.

Value Creation in Crowd-Business: Developing a Framework for Successful Implementation of Crowdsourcing Initiatives

By recent years the phenomenon called crowdsourcing has been acknowledged as an innovative form of value creation that must be taken seriously. Crowdsourcing can be defined as an act of outsourcing tasks originally performed inside an organization, or assigned externally in form of a business relationship, to an undefinably large, heterogeneous mass of potential actors. This thesis constructs a framework for successful implementation of crowdsourcing initiatives. Firms that rely entirely on their own research and ideas cannot compete with the innovative capacity that crowd-powered firms have. Nowadays, crowdsourcing has become one of the key capabilities of businesses due to its innovative capabilities, in addition to the existing internal resources of the firm. By utilizing crowdsourcing the business gains access to an enormous pool of competence and knowledge. However, various risks remain such as uncertainty of crowd structure and loss of internal know-how. Crowdsourcing Success Framework introduces a step by step model for implementing crowdsourcing into the everyday operations of the business. It starts from the decision to utilize crowdsourcing and continues further into planning, organizing and execution. Finally, this thesis presents the success factors of crowdsourcing initiative.

A Phase Model for Building a Customer Value Based Sales Tool – Case Mining and Metals Industry

The objective of this research is to observe the state of customer value management in Outotec Oyj, determine the key development areas and develop a phase model with which to guide the development of a customer value based sales tool. The study was conducted with a constructive research approach with the focus of identifying a problem and developing a solution for the problem. As a basis for the study, the current literature involving customer value assessment and solution and customer value selling was studied. The data was collected by conducting 16 interviews in two rounds within the company and it was analyzed by coding openly. First, seven important development areas were identified, out of which the most critical were “Customer value mindset inside the company” and “Coordination of customer value management activities”. Utilizing these seven areas three functionality requirements, “Preparation”, “Outotec’s value creation and communication” and “Documentation” and three development requirements for a customer value sales tool were identified. The study concluded with the formulation of a phase model for building a customer value based sales tool. The model included five steps that were defined as 1) Enable customer value utilization, 2) Connect with the customer, 3) Create customer value, 4) Define tool to facilitate value selling and 5) Develop sales tool. Further practical activities were also recommended as a guide for executing the phase model.