Synnytyksen ponnistusvaiheen hoidon käytännöt. Yhteys ensisynnyttäjän välilihan kuntoon synnytyksen jälkeen, synnytyskokemukseen, kipuun ja seksuaaliterveyteen

Hyvän syntymän hoidon tavoitteena on turvata synnyttäjän paras mahdollinen terveys, vähentää tarpeetonta puuttumista synnytyksen kulkuun ja mahdollistaa voimaannuttava synnytyskokemus perheelle. Hyvä syntymän hoito ja siihen liittyvä kätilöiden kliinisen hoitotyön osaaminen ei voi kehittyä, ellei hoitotyön käytäntöjä tutkita. Suomalaista hoitotieteellistä syntymän hoitoon liittyvää tutkimusta on vähän. Tämän tutkimuksen tarkoituksena oli kuvata synnytyksen ponnistusvaiheen hoidon käytäntöjä Suomen synnytyssairaaloissa. Lisäksi seurantatutkimuksen avulla selvitettiin, miten ensisynnyttäjät kokivat synnytyksen ponnistusvaiheen, sen aikana saamansa hoidon, ensisynnyttäjien synnytyskokemusta, kivun kokemista, vointia kolmena päivänä synnytyksen jälkeen sekä heidän seksuaaliterveyttään ensimmäisen vuoden aikana synnytyksen jälkeen. Tutkimuksen tavoitteena oli tuottaa tietoa, jonka avulla voidaan kehittää synnytyksen ponnistusvaiheen hoitoa ja lisätä tietoa synnyttäneiden naisten voinnista ja seksuaaliterveydestä. Tutkimuksen ensimmäinen osio toteutettiin poikkileikkaustutkimuksena (2009), johon osallistui Suomen synnytyssairaaloiden synnytysosastoilla työskentelevät kätilöt (N = 662). Tutkimuksen toinen osio toteutettiin seurantatutkimuksena (2009−2011), jossa oli neljä mittausajankohtaa: kolmantena päivänä synnytyksestä sekä kolmen, kuuden ja kahdentoista kuukauden kuluttua synnytyksestä. Tähän osioon osallistui spontaanisti alateitse yhden elävän lapsen (pää tarjoutuvana) synnyttäneet ensisynnyttäjät (N = 453) ja sikiön perätilan vuoksi suunnitellusti keisarileikatut ensisynnyttäjät (N = 84). Aineisto analysoitiin tilastollisin menetelmin. Tutkimustulosten mukaan osa kätilöiden käyttämistä synnytyksen ponnistusvaiheen hoitokäytännöistä ei ole näyttöön perustuvia. Synnytyssairaalan synnytyksen hoidon kulttuuri näyttää siirtyvän mallioppimisen kautta. Ensisynnyttäjät kokivat synnytyksen ponnistusvaiheen hoidon pääsääntöisesti myönteisenä. Alateitse synnyttäneillä ensisynnyttäjillä oli myönteisempi synnytyskokemus ja vähemmän kipua heti synnytyksen jälkeen ja kolmena synnytyksen jälkeisenä päivänä verrattuna keisarileikkauksella synnyttäneisiin ensisynnyttäjiin. Alateitse synnyttäneillä ensisynnyttäjillä kipu ja ompeleet eivät vaikuttaneet haitallisesti vastasyntyneen hoitoon tai imetykseen niin paljon kuin keisarileikkauksella synnyttäneillä ensisynnyttäjillä. Välilihan leikkaus-, repeämä- tai keisarileikkaushaavat olivat täysin parantuneet suurimmalla osalla naisista kolmen kuukauden kuluttua synnytyksestä. Yleisimpiä naisten kokemia oireita ensimmäisen vuoden aikana synnytyksestä olivat emättimen kostumisen vaikeus, yhdyntäkivut, peräpukamat sekä arpikudoksen kipu ja kiristys. Sukupuolinen halukkuus ja tyytyväisyys seksielämään olivat huonompaa ensimmäisen vuoden aikana synnytyksestä verrattuna aikaan ennen raskautta ja synnytystä. Synnytyksen aikaisella hoitotyöllä ja näyttöön perustuvalla synnytyksen ponnistusvaiheen hoidolla on suuri merkitys naisen synnytyskokemukseen, synnytyksen jälkeiseen vointiin ja seksuaaliterveyteen.

Prenatal and perinatal risk factors for bipolar disorder

Bipolar disorder (BPD) is a severe mental disorder associated with considerable morbidity and mortality. Prenatal insults have been shown to be associated with later development of mental disorders and there is a growing interest in the potential role of prenatal and perinatal risk factors in the development of BPD. The aims of this thesis were to describe the overall study design of the Finnish Prenatal Study of Bipolar Disorders (FIPS-B) and demographic characteristics of the sample. Furthermore, it was aimed to examine the association of parental age, parental age difference, perinatal complications and maternal smoking during pregnancy with BPD. This thesis is based on FIPS-B, a nested case-control study using several nationwide registers. The cases included all people born in Finland between January 1st 1983 and December 31st 1998 and diagnosed with BPD according to the Finnish Hospital Discharge Register (FHDR) before December 31st 2008. Controls for this study were people who were without BPD, schizophrenia or diagnoses related to these disorders, identified from the Population Register Centre (PRC), and matched two-fold to the cases on sex, date of birth (+/- 30 days), and residence in Finland on the first day of diagnosis of the matched case. Conditional logistic regression models were used to examine the association between risk factors and BPD. This study included 1887 BPD cases and 3774 matched controls. The mean age at diagnosis was 19.3 years and females accounted for 68% of the cases. Mothers with the lowest educational level had the highest odds of having BPD in offspring. Being born in Eastern and Southern region of Finland increased the odds of having BPD later in life. A U-shaped distribution of odds ratio was observed between paternal age and BPD in the unadjusted analysis. Maternal age and parental age difference was not associated with BPD. Birth by planned caesarean section was associated with increased odd of BPD. Smoking during pregnancy was not associated with BPD in the adjusted analyses. Region of birth and maternal educational level were associated with BPD. Both young and old father’s age was associated with BPD. Most perinatal complications and maternal smoking during pregnancy were not associated with BPD. The findings of this thesis, considered together with previous literature, suggest that the pre- and perinatal risk factor profile varies among different psychiatric disorders.

Cesarean section - short term maternal complications related to the mode of delivery

Cesarean section (CS) is the most common major surgery performed on women worldwide. CS can save the life of the mother or the fetus, but is associated with the typical complications of any major surgery: hemorrhage, infection, venous thromboembolism and complications of anesthesia, sometimes leading to maternal death. Recently there have been several reports from well resourced countries on increased severe maternal morbidity and even mortality. Increased rates of CS, obesity and older mothers may explain this rise. The aim of this thesis is to study the rates and risk factors of short term maternal complications associated with CS. Also, we compared maternal morbidity by mode of delivery and over time. The complication rates were assessed in a prospective study involving 2496 CS performed in the 12 largest delivery units in Finland in 2005. The rates of severe complications were studied by mode of delivery in a register-based study comparing national cohorts in 1997 and 2002. The impact of several risk factors on severe maternal morbidity by mode of delivery was studied in a register-based study of all singleton deliveries in 2007-2011. In the prospective study, 27% of the women who underwent CS had one or more intraoperative or postoperative complications during their hospital stay, and 10% had a severe complication. In the register-based study the incidence of life-threatening maternal complications was 7.6 in 1000 deliveries. The incidence was lowest for vaginal delivery (VD), followed by instrumental VD and elective CS, and highest in emergency CS. An attempt of VD, including the risks associated with emergency CS, seems to be the safest mode of delivery, even for most high-risk women.

Ash Particle Erosion on Steam Boiler Convective Section

In this study, equations for the calculation of erosion wear caused by ash particles on convective heat exchanger tubes of steam boilers are presented. Anew, three-dimensional test arrangement was used in the testing of the erosion wear of convective heat exchanger tubes of steam boilers. When using the sleeve-method, three different tube materials and three tube constructions could be tested. New results were obtained from the analyses. The main mechanisms of erosionwear phenomena and erosion wear as a function of collision conditions and material properties have been studied. Properties of fossil fuels have also been presented. When burning solid fuels, such as pulverized coal and peat in steam boilers, most of the ash is entrained by the flue gas in the furnace. In bubbling andcirculating fluidized bed boilers, particle concentration in the flue gas is high because of bed material entrained in the flue gas. Hard particles, such as sharp edged quartz crystals, cause erosion wear when colliding on convective heat exchanger tubes and on the rear wall of the steam boiler. The most important ways to reduce erosion wear in steam boilers is to keep the velocity of the flue gas moderate and prevent channelling of the ash flow in a certain part of the cross section of the flue gas channel, especially near the back wall. One can do this by constructing the boiler with the following components. Screen plates can beused to make the velocity and ash flow distributions more even at the cross-section of the channel. Shield plates and plate type constructions in superheaters can also be used. Erosion testing was conducted with three types of tube constructions: a one tube row, an inline tube bank with six tube rows, and a staggered tube bank with six tube rows. Three flow velocities and two particle concentrations were used in the tests, which were carried out at room temperature. Three particle materials were used: quartz, coal ash and peat ash particles. Mass loss, diameter loss and wall thickness loss measurements of the test sleeves were taken. Erosion wear as a function of flow conditions, tube material and tube construction was analyzed by single-variable linear regression analysis. In developing the erosion wear calculation equations, multi-variable linear regression analysis was used. In the staggered tube bank, erosion wear had a maximum value in a tube row 2 and a local maximum in row 5. In rows 3, 4 and 6, the erosion rate was low. On the other hand, in the in-line tube bank the minimum erosion rate occurred in tube row 2 and in further rows the erosion had an increasing value, so that in a six row tube bank, the maximum value occurred in row 6.

Calculation of the critical crack size for cold form rectangular hollow section tube (CRHS) under bending load at -40º C temperature

To predict the capacity of the structure or the point which is followed by instability, calculation of the critical crack size is important. Structures usually contain several cracks but not necessarily all of these cracks lead to failure or reach the critical size. So, defining the harmful cracks or the crack size which is the most leading one to failure provides criteria for structure’s capacity at elevated temperature. The scope of this thesis was to calculate fracture parameters like stress intensity factor, the J integral and plastic and ultimate capacity of the structure to estimate critical crack size for this specific structure. Several three dimensional (3D) simulations using finite element method by Ansys program and boundary element method by Frank 3D program were carried out to calculate fracture parameters and results with the aid of laboratory tests (loaddisplacement curve, the J resistance curve and yield or ultimate stress) leaded to extract critical size of the crack. Two types of the fracture which is usually affected by temperature, Elastic and Elasti-Plastic fractures were simulated by performing several linear elastic and nonlinear elastic analyses. Geometry details of the weldment; flank angle and toe radius were also studied independently to estimate the location of crack initiation and simulate stress field in early stages of crack extension in structure. In this work also overview of the structure’s capacity in room temperature (20 ºC) was studied. Comparison of the results in different temperature (20 ºC and -40 ºC) provides a threshold of the structure’s behavior within the defined range.

Reducing Manufacturing Costs of the Screen Dryer’s Hot Section by Design

In this thesis, the purpose was to find the cost distribution of the screen dryer and the largest cost factors. The hot section of the screen dryer was revealed as the biggest cost factor, so composing new cost efficient solutions were directed to it. DFMA (Design for Manufacture and Assembly) was chosen to help the design process. DFMA is a product design strategy developed for taking manufacturing and assembly costs into account at the early stages of the design process. In the theory part of the thesis, other methods of economical design and tools needed for estimating manufacturing costs are introduced. In the empirical part, the hot section of the screen dryer was divided into sub-assemblies and their manufacturing costs were estimated. The design propositions were directed to the self-manufactured assemblies and parts. The new manufacturing costs were calculated for the developed propositions. Lastly, the most cost efficient solutions were summarized. The savings on the self-manufactured assemblies were about 40 %, which was about 13 % of the combined total costs of the hot section.

Performance of high power fibre laser cutting of thick-section steel and mediumsection aluminium

Cutting of thick section stainless steel and mild steel, and medium section aluminium using the high power ytterbium fibre laser has been experimentally investigated in this study. Theoretical models of the laser power requirement for cutting of a metal workpiece and the melt removal rate were also developed. The calculated laser power requirement was correlated to the laser power used for the cutting of 10 mm stainless steel workpiece and 15 mm mild steel workpiece using the ytterbium fibre laser and the CO2 laser. Nitrogen assist gas was used for cutting of stainless steel and oxygen was used for mild steel cutting. It was found that the incident laser power required for cutting at a given cutting speed was lower for fibre laser cutting than for CO2 laser cutting indicating a higher absorptivity of the fibre laser beam by the workpiece and higher melting efficiency for the fibre laser beam than for the CO2 laser beam. The difficulty in achieving an efficient melt removal during high speed cutting of the 15 mmmild steel workpiece with oxygen assist gas using the ytterbium fibre laser can be attributed to the high melting efficiency of the ytterbium fibre laser. The calculated melt flow velocity and melt film thickness correlated well with the location of the boundary layer separation point on the 10 mm stainless steel cut edges. An increase in the melt film thickness caused by deceleration of the melt particles in the boundary layer by the viscous shear forces results in the flow separation. The melt flow velocity increases with an increase in assist gas pressure and cut kerf width resulting in a reduction in the melt film thickness and the boundary layer separation point moves closer to the bottom cut edge. The cut edge quality was examined by visual inspection of the cut samples and measurement of the cut kerf width, boundary layer separation point, cut edge squareness (perpendicularity) deviation, and cut edge surface roughness as output quality factors. Different regions of cut edge quality in 10 mm stainless steel and 4 mm aluminium workpieces were defined for different combinations of cutting speed and laserpower.Optimization of processing parameters for a high cut edge quality in 10 mmstainless steel was demonstrated

Travels in various countries of Europe, Asia and Africa : Part the third : Scandinavia : Section the second : by Edward Daniel Clarke.

Digital reproduction, The National Library of Finland, Centre for Preservation and Digitisation, Mikkeli

Travels in various countries of Europe, Asia and Africa : Part the third : Scandinavia : Section the first : by Edward Daniel Clarke.

Digital reproduction, The National Library of Finland, Centre for Preservation and Digitisation, Mikkeli

Enhancement of water removal in the press section

The effectiveness of water removal on press section is very important for a paper and board machine’s functioning, efficiency and economy. Today, the most effective method for wet pressing is shoe press technology. Metso has carried out a number of studies concerning anew type of water removal method for a press section, which has also been patented. These studies include rough sketches and some test runs. These issues form the basis of this thesis. The objective of this work was to gather together information for a new and enhanced waterremoval method for a press section by studying the functioning of the device andcarrying out test runs. This method is referred to here as Hydronip. The main goal was tobuild a functional test site which fulfills all the necessary requirements and has all thenecessary information gathering devices. The design process was carried out by emphasizing the safety aspects. The goal was also to gather together information about the nip structure in running conditions, the seal function, and to carry out the nip tests with paper or board wads. This thesis consists of a theory part, the design and construction of the test site, and carrying out test runs through information gathering. The theory part consists of the principals of water removal from a press section, Hydronip construction, and the requirements for the test place. The safety aspects were taken into account especially in test runs, but also in the assembly stages. The design and construction of the test site includes the selection of equipment and surroundings that are needed for managing the test runs in the best possible way at certain premises. The test site included the equipment that was already on the premises. Some equipment could be used as it was but some equipment had to be manufactured or modified from existing equipment. A functional test site with information gathering devices was accomplished as a result of thethesis. Test runs demonstrated that the Hydronip concept is, at least on a small scale,functional. Short-term tests for seal functioning showed that the seal can be lubricatedsufficiently under different kinds of nip load situations. Wad tests demonstrated that the metal belt is durable against different sizes of external particles. The seal also endured wad tests even though the pressure impacts impaired the lubrication. MTS tests showing dry content increases, combined with a rough cost calculation and the basic function of the machine in test runs, show that with some further study Hydronip could be a promising new product for water removal from a paper or board machine’s press section.

XIIe olympiade Helsinki 1940 section des Billets

37 x 41 cm

XIIth olympic games Helsinki 1940 ticket section

36 x 41 cm

Section Helsinki

21 x 18 cm

Ultimate capacity of stainless steel rectangular hollow section X- joints at low temperatures

Growing demand for stainless steel construction materials has increased the popularity of substitutive materials for austenitic stainless steels. The lean duplex grades have taken their place in building of structures exposed to corrosive environments. Since the duplex grades are relatively new materials, the current codes and norms do not fully cover the newest duplex grades. The joints tested in this thesis were designed and studied according to Eurocode 3, even though all the materials are not yet accepted to the standards. The main objective in this thesis was to determine the differences of the used materials in behaviour under loading at low temperatures. Tests in which the deformation and strength properties of the joints were determined were done at the temperature of -46°C, which is the requirement of temperature for structures designed according to Norsok standards. Results show that replacing the austenitic grade with the lean duplex grade is acceptable.