Model for managing non-core ideas to new companies, products and services in a Finnish forest company

Suomalainen metsäteollisuus on muutoksen partaalla. Uutisissa on nähty miten metsäyrityksen sulkevat tehtaita ja paperikoneita. Suomalaisessa metsäteollisuudessa keskitytään tällä hetkellä lähinnä kulujen alentamiseen ja tuottavuuden parantamiseen. Edellytyssille, että suomalainen metsäteollisuus pysyy kilpailukykyisenä, ovat kuitenkinuudet innovaatiot ja toimialojen välinen yhteistyö. Työn tavoitteena oli luoda toimintamalli UPM-Kymmene Oyj:lle, minkä avulla ydinliiketoimintaan kuulumattomat tuote- ja palveluideat saataisiin hyödynnettyä. Aihe on erittäin ajankohtainen, mikäli halutaan pitää tuotanto jatkossakin Suomessa. Luotumalli painottaa pk-sektorin roolia ja potentiaalia kehittää UPM-Kymmeneltä peräisin olevia ja heidän ydinliiketointaan kuulumattomista tuote ja palveluideoistauusia yrityksiä, tuotteita ja palveluita. Malli edustaa uudenlaista ajattelutapaa ja sen käyttöönotto vaatii perinteisen yrityskulttuurin uudistamista UPM-Kymmenessä.

Supply chain costs of a small board lot: sheet cutting and logistics

Succeeding in small board lot (0-20 tons) deliveries, is not always prosperous and failures as well as extra costs compared to standard costs arise. Failure deliveries from converting plants to customer locations tie a lot of unwanted and unexpected costs. Extra costs are handled as quality costs and more precise, internal failure costs. These costs revolve from unsuccessful truck payloads, redundant warehousing or unfavorable routing as examples. Quality costs are becoming more and more important factor in company’s financial decision making. Actual, realized truck payload correlates with the extra costs occurring, so filling the truck payload all get-out well is a key to lower the extra costs. Case company in this study is Corporation A, business segment Boards. Boards have outsourced half of their converting in order to gain better customer service via flexibility, lead time reductions and logistics efficiency improvements. Examination period of the study is first two quarters of year 2008 and deliveries examined are from converters to the customer locations. In Corporation A’s case, the total loss in failure deliveries is hundreds of thousands of Euros during the examination period. So, the logistics goal of getting the right product to the right place and right time for the least cost, does not completely realize.

Feasibility of industrial implementation of laser cutting into paper making machine

Laser cutting implementation possibilities into paper making machine was studied as the main objective of the work. Laser cutting technology application was considered as a replacement tool for conventional cutting methods used in paper making machines for longitudinal cutting such as edge trimming at different paper making process and tambour roll slitting. Laser cutting of paper was tested in 70’s for the first time. Since then, laser cutting and processing has been applied for paper materials with different level of success in industry. Laser cutting can be employed for longitudinal cutting of paper web in machine direction. The most common conventional cutting methods include water jet cutting and rotating slitting blades applied in paper making machines. Cutting with CO2 laser fulfils basic requirements for cutting quality, applicability to material and cutting speeds in all locations where longitudinal cutting is needed. Literature review provided description of advantages, disadvantages and challenges of laser technology when it was applied for cutting of paper material with particular attention to cutting of moving paper web. Based on studied laser cutting capabilities and problem definition of conventional cutting technologies, preliminary selection of the most promising application area was carried out. Laser cutting (trimming) of paper web edges in wet end was estimated to be the most promising area where it can be implemented. This assumption was made on the basis of rate of web breaks occurrence. It was found that up to 64 % of total number of web breaks occurred in wet end, particularly in location of so called open draws where paper web was transferred unsupported by wire or felt. Distribution of web breaks in machine cross direction revealed that defects of paper web edge was the main reason of tearing initiation and consequent web break. The assumption was made that laser cutting was capable of improvement of laser cut edge tensile strength due to high cutting quality and sealing effect of the edge after laser cutting. Studies of laser ablation of cellulose supported this claim. Linear energy needed for cutting was calculated with regard to paper web properties in intended laser cutting location. Calculated linear cutting energy was verified with series of laser cutting. Practically obtained laser energy needed for cutting deviated from calculated values. This could be explained by difference in heat transfer via radiation in laser cutting and different absorption characteristics of dry and moist paper material. Laser cut samples (both dry and moist (dry matter content about 25-40%)) were tested for strength properties. It was shown that tensile strength and strain break of laser cut samples are similar to corresponding values of non-laser cut samples. Chosen method, however, did not address tensile strength of laser cut edge in particular. Thus, the assumption of improving strength properties with laser cutting was not fully proved. Laser cutting effect on possible pollution of mill broke (recycling of trimmed edge) was carried out. Laser cut samples (both dry and moist) were tested on the content of dirt particles. The tests revealed that accumulation of dust particles on the surface of moist samples can take place. This has to be taken into account to prevent contamination of pulp suspension when trim waste is recycled. Material loss due to evaporation during laser cutting and amount of solid residues after cutting were evaluated. Edge trimming with laser would result in 0.25 kg/h of solid residues and 2.5 kg/h of lost material due to evaporation. Schemes of laser cutting implementation and needed laser equipment were discussed. Generally, laser cutting system would require two laser sources (one laser source for each cutting zone), set of beam transfer and focusing optics and cutting heads. In order to increase reliability of system, it was suggested that each laser source would have double capacity. That would allow to perform cutting employing one laser source working at full capacity for both cutting zones. Laser technology is in required level at the moment and do not require additional development. Moreover, capacity of speed increase is high due to availability high power laser sources what can support the tendency of speed increase of paper making machines. Laser cutting system would require special roll to maintain cutting. The scheme of such roll was proposed as well as roll integration into paper making machine. Laser cutting can be done in location of central roll in press section, before so-called open draw where many web breaks occur, where it has potential to improve runability of a paper making machine. Economic performance of laser cutting was done as comparison of laser cutting system and water jet cutting working in the same conditions. It was revealed that laser cutting would still be about two times more expensive compared to water jet cutting. This is mainly due to high investment cost of laser equipment and poor energy efficiency of CO2 lasers. Another factor is that laser cutting causes material loss due to evaporation whereas water jet cutting almost does not cause material loss. Despite difficulties of laser cutting implementation in paper making machine, its implementation can be beneficial. The crucial role in that is possibility to improve cut edge strength properties and consequently reduce number of web breaks. Capacity of laser cutting to maintain cutting speeds which exceed current speeds of paper making machines what is another argument to consider laser cutting technology in design of new high speed paper making machines.

Cost-plus-loss analyses of forest inventory strategies based on kNN-assigned reference sample plot data

Abstract

Lihahygienialainsäädännön omavalvontasäädökset ja käytäntö Oy Snellman Ab:n teurastamossa ja leikkaamossa, osa I Osa 1 : Owncontrol directions in meat hygiene legislation and their practical implementation in the slaughterhouse and cutting plant of Snellman Ltd, part I

Summary: Owncontrol directions in meat hygiene legislation and their practical implementation in the slaughterhouse and cutting plant of Snellman Ltd, part I

Cost-benefit analysis of multifunctional agriculture in Finland

Selostus: Kustannus-hyötyanalyysi monivaikutteisesta maataloudesta

Cost-effective measures for diffuse load abatement in forestry

Abstract

Export of dissolved organic carbon, nitrogen and phosphorus following clear-cutting of three Norway spruce forest growing on drained peatlands in southern Finland

Abstract

Degree of previous cutting in explaining the differences in diameter distributions between mature managed and natural Norway spruce forests

Abstract

Growth and recruitment after mountain forest selective cutting in irregular spruce forest : a case study in northern Norway

Abstract

Growth rate and wood properties of Norway spruce cutting clones on different sites

[Abstract]