Comparison of electricity generation costs

The economical competitiveness of various power plant alternatives is compared. The comparison comprises merely electricity producing power plants. Combined heat and power (CHP) producing power will cover part of the future power deficit in Finland, but also condensing power plants for base load production will be needed. The following types of power plants are studied: nuclear power plant, combined cycle gas turbine plant, coal-fired condensing power plant, peat-fired condensing power plant, wood-fired condensing power plant and wind power plant. The calculations are carried out by using the annuity method with a real interest rate of 5 % per annum and with a fixed price level as of January 2008. With the annual peak load utilization time of 8000 hours (corresponding to a load factor of 91,3 %) the production costs would be for nuclear electricity 35,0 €/MWh, for gas based electricity 59,2 €/MWh and for coal based electricity 64,4 €/MWh, when using a price of 23 €/tonCO2 for the carbon dioxide emission trading. Without emission trading the production cost of gas electricity is 51,2 €/MWh and that of coal electricity 45,7 €/MWh and nuclear remains the same (35,0 €/MWh) In order to study the impact of changes in the input data, a sensitivity analysis has been carried out. It reveals that the advantage of the nuclear power is quite clear. E.g. the nuclear electricity is rather insensitive to the changes of nuclear fuel price, whereas for natural gas alternative the rising trend of gas price causes the greatest risk. Furthermore, increase of emission trading price improves the competitiveness of the nuclear alternative. The competitiveness and payback of the nuclear power investment is studied also as such by using various electricity market prices for determining the revenues generated by the investment. The profitability of the investment is excellent, if the market price of electricity is 50 €/MWh or more.

Life cycle costs in heating, ventilation and air-conditioning systems with drive

Energy consumption and energy efficiency have become an issue. Energy consumption is rising all over the world and because of that, and the climate change, energy is becoming more and more expensive. Buildings are major consumers of energy, and inside the buildings the major consumers are heating, ventilation and air-conditioning systems. They usually run at constant speed without efficient control. In most cases HVAC equipment is also oversized. Traditionally heating, ventilation and air-conditioning systems have been sized to meet conditions that rarely occur. The theory part in this thesis represents the basics of life cycle costs and calculations for the whole life cycle of a system. It also represents HVAC systems, equipment, systems controls and ways to save energy in these systems. The empirical part of this thesis represents life cycle cost calculations for HVAC systems. With these calculations it is possible to compute costs for the whole life cycle for the wanted variables. Life cycle costs make it possible to compare which variable causes most of the costs from the whole life point of view. Life cycle costs were studied through two real life cases which were focused on two different kinds of HVAC systems. In both of these cases the renovations were already made, so that the comparison between the old and the new, now existing system would be easier. The study indicates that energy can be saved in HVAC systems by using variable speed drive as a control method.

Warranty Practices and Costs in the Industry of Welding Machines Manufacturing

The objective of the master’s thesis is to define the warranty practices and costs in the welding machines manufacturing company and do a proposal for a warranty policy based on the practices and costs. The study include a disquisition of the warranty practices in the subsidiaries and distributor sales. The disquisition of the warranty practices introduces the information relates to warranty period, warranty costs, including repair, spare part and other costs, the practices with the replaced parts, the utilization rate of the eWarranty system and information relates to special arrangements in the warranties. The warranty costs are defined besides the group level also separately per regions and product families. From some product families the disquisition is done per products. In this study is also done a proposal for a warranty policy for the company. The proposal speaks out the length of warranty period, the compensation of the warranty costs, the practices with replaced parts and usage of eWarranty system.

Defining a framework model to determine total costs of managed desktops using ITIL best practices

In modern day organizations there are an increasing number of IT devices such as computers, mobile phones and printers. These devices can be located and maintained by using specialized IT management applications. Costs related to a single device accumulate from various sources and are normally categorized as direct costs like hardware costs and indirect costs such as labor costs. These costs can be saved in a configuration management database and presented to users using web based development tools such as ASP.NET. The overall costs of IT devices during their lifecycle can be ten times higher than the actual purchase price of the product and ability to define and reduce these costs can save organizations noticeable amount of money. This Master’s Thesis introduces the research field of IT management and defines a custom framework model based on Information Technology Infrastructure Library (ITIL) best practices which is designed to be implemented as part of an existing IT management application for defining and presenting IT costs.

Seisokkien aiheuttamat kustannukset ja tulonmenetykset ongelma- ja yhdyskuntajätteen termisessä käsittelyssä

Tämän opinnäytetyön tarkoituksena oli selvittää seisokkitunnista aiheutuvat kustannukset ja tulonmenetykset eri polttolinjoille ja niiden kombinaatioille Ekokem Oy Ab:n jätteenpolttolaitoksessa. Työ suoritettiin tarkastelemalla prosessitietokantaan tallentunutta tietoa sekä keräämällä tietoa haastatteluilla. Jätetulon menetyksen määrittelytavalla oli keskeinen vaikutus tulonmenetysten muodostumiseen. Muita kustannuksiin ja tulonmenetyksiin vaikuttavia tekijöitä olivat vuodenaika, seisokin pituus ja energiantoimituksen sopimukset. Kaikissa seisokeissa ei välttämättä aiheudu välitöntä jätetulon menetystä, mutta käsittelemättä jäävän jätteen voidaan silti nähdä aiheuttavan tilapäisvarastoinnin tarvetta, josta aiheutuu kustannuksia. Tämän vuoksi eri polttolinjojen jätetulon menetys laskettiin kahdella tavalla olettaen ensin kaiken polttamatta jäävän jätteen aiheuttavan jätetulon menetystä sekä siten, että jätetulon menetys ja mahdollisesta varastoinnista aiheutuvat kustannukset arvioitiin kokemusperäisesti. Jätetulon todellisten menetysten määräytyminen voi tapahtua kummalla tavalla hyvänsä riippuen seisokkihetkellä vallitsevista olosuhteista. Kustannukset ja tulonmenetykset laskettiin kolmelle eripituiselle ajanjaksolle ja jaettiin tuntihinnoiksi. Työssä käsitellyille eri seisokkitilanteille saatiin 131 eri tuntihintaa kun muuttujia vaihdeltiin. Suurimmat kustannukset ja tulonmenetykset muodostuivat jätevoimalan seisokista lämmityskaudella. Tämä johtui siitä, että jätevoimalassa poltettavaa yhdyskuntajätettä ei pystytä varastoimaan toisin kuin ongelmajätteitä. Jätevoimalan seisokkitunti voi lämmityskaudella maksaa enimmillään 2600 €/h, josta menetetyn jätetulon osuus on liki puolet. Lisäksi jätevoimalan höyryntuotanto on yli puolet kokonaistuotannosta.

Lähiverkkotuotteen palveluprosessien kehittäminen, Case: Elisa

Diplomityön aiheena oli tutkia case-yrityksen prosessikehitystä, prosessijohtamista sekä lähiverkkopalveluketjua prosessinäkökulman kannalta. Tutkimuksen päätavoitteina oli selvittää, kuinka lähiverkkopalveluketjun toimintaa voisi tehostaa, ja minkälaisia kertakustannuksia yhdestä keskiverotoimituksesta syntyy. Tavoitteina oli myös selvittää yrityksen prosessikehittämisen tila sekä minkälaisia prosessijohtamismalleja yrityksessä käytetään ja millä tavoin sen pääprosesseja johdetaan. Tutkimus oli case-tyyppinen, eli siinä tutkittiin yhden yrityksen toimintaa ja prosesseja. Teoreettinen pohja tutkimukselle luotiin käsittelemällä liiketoimintaprosesseihin liittyviä ydinmääritelmiä, erilaisia prosessijohtamismalleja ja liiketoimintaprosessien mittaamista. Tutkimuksen peruselementit tiedon hankintaan olivat kirjallisuus ja haastattelut. Lisäksi tutkimus pohjasi vahvasti tutkijan tekemiin omiin havaintoihin yrityksessä ja sen toimintaympäristössä. Tutkimuksen ensimmäisessä vaiheessa kartoitettiin lähiverkkopalveluketjun senhetkinen tilanne, analysoitiin palveluketjun sisältämiä prosesseja ja kirjattiin ylös havaitut ongelmakohdat. Haastatteluista kerättyjen tietojen perusteella laskettiin yhdestä keskivertolähiverkkotoimituksesta case-yritykselle syntyvät kertakustannukset. Tämän lisäksi analysoitiin yrityksen senhetkistä prosessijohtamis- ja prosessikehitystasoa sekä peilattiin niitä yrityksen tulevaisuuden prosessikehittämistoimiin. Lopuksi johtopäätöksien kautta esitettiin kaksi toimintaehdotusta, joilla palveluketjun toimintaa voitaisiin parantaa. Ensimmäinen ehdotus oli radikaalimpi, ja siinä siirryttäisiin kokonaan pois palveluketjumallista tiimipohjaiseen malliin. Toisessa ehdotuksessa keskityttiin korjaamaan palveluketjun ongelmakohtia.

Cumulative Costs of Caries Prevention and Treatment in Children - with Special Reference to Work Division and Cohort Effect

Lapsen karieshoidon kustannuskertymän muutokset ja karieshoidon toimintakäytäntöjen yhteys kustannuksiin Tutkimuksen tavoitteena oli mitata terveyskeskuksessa hoidettavien lasten karieshoidon kumulatiivisia kustannuksia ja verrata niitä kahden erilaisen toimintatavan välillä. Lisäksi tarkasteltiin lasten hampaiden terveyttä. Tutkimus tehtiin julkisen palvelutuottajan näkökulmasta. Tutkimusaineisto kerättiin Kemin ja Tornion terveyskeskusten suun terveydenhuollon potilaskertomuksista. Kemin kohortit 1980, 1983 ja 1986 (n = 600) ja Tornion kohortit 1980 ja 1992 (n = 400) edustivat perinteistä ja Kemin kohortit 1989, 1992 ja 1995 (n = 600) uutta toimintatapaa työnjaon ja ehkäisyn ajoituksen suhteen. Kohortteja ja kaupunkeja verrattiin hampaiden terveyden (dmft/DMFT = 0 ja dmft ja DMFT keskiarvot 5 ja 12 vuoden iässä) ja voimavarojen käytön suhteen. Panoskäyttö johdettiin käyntimäärien avulla laskennallisen työajan kautta. Kustannuskertymät muodostettiin käyttämällä henkilöstömenoista laskettuja suorittajakohtaisia yksikkökustannuksia. Panoskäytön ja yksikkökustannusten kautta muodostettiin kustannuskertymät. Kustannusten ja terveysvaikutusten suhteita arvioitiin kustannus-vaikuttavuusanalyysissä. Suuhygienistien työpanosta hyödyntävällä varhaisen ehkäisyn toimintamallilla saavutettiin vähäisemmin kustannuksin alle kouluiässä parempi ja kouluiässä yhtä hyvä hammasterveys kuin perinteisellä, enemmän hammaslääkärien työpanokseen perustuvalla tavalla. Karieksen hoitoon liittyvien käyntien määrä oli nuorimmissa syntymävuosikohorteissa pienempi kuin vanhimmissa kohorteissa. Käynnit hammaslääkärissä vähenivät eniten. Toimintatavalla oli merkittävä vaikutus lapsen karieshoidon kokonaiskustannuksiin. Herkkyysanalyysin mukaan karieshoidon kustannukset olivat työnjakoa hyödyntämällä kolmanneksen pienemmät, kuin jos hoidon suorittajana olisi ollut ainoastaan hammaslääkäri-hoitaja työpari. Lasten karieshoidon kustannusvaikuttavuus kohentui molemmissa terveyskeskuksissa nuoremmissa kohorteissa vanhempiin verrattuna. Suun terveydenhuollon potilaskertomuksia olisi hyödynnettävä toiminnan kehittämisessä. Varhaisen ehkäisyn avulla voitaisiin kaikkien suun terveydenhuollon ammattihenkilöiden työpanos kohdentaa kustannustehokkaasti.

The effects of real time control of welding parameters on weld quality in plasma arc keyhole welding

Joints intended for welding frequently show variations in geometry and position, for which it is unfortunately not possible to apply a single set of operating parameters to ensure constant quality. The cause of this difficulty lies in a number of factors, including inaccurate joint preparation and joint fit up, tack welds, as well as thermal distortion of the workpiece. In plasma arc keyhole welding of butt joints, deviations in the gap width may cause weld defects such as an incomplete weld bead, excessive penetration and burn through. Manual adjustment of welding parameters to compensate for variations in the gap width is very difficult, and unsatisfactory weld quality is often obtained. In this study a control system for plasma arc keyhole welding has been developed and used to study the effects of the real time control of welding parameters on gap tolerance during welding of austenitic stainless steel AISI 304L. The welding tests demonstrated the beneficial effect of real time control on weld quality. Compared with welding using constant parameters, the maximum tolerable gap width with an acceptable weld quality was 47% higher when using the real time controlled parameters for a plate thickness of 5 mm. In addition, burn through occurred with significantly larger gap widths when parameters were controlled in real time. Increased gap tolerance enables joints to be prepared and fit up less accurately, saving time and preparation costs for welding. In addition to the control system, a novel technique for back face monitoring is described in this study. The test results showed that the technique could be successfully applied for penetration monitoring when welding non magnetic materials. The results also imply that it is possible to measure the dimensions of the plasma efflux or weld root, and use this information in a feedback control system and, thus, maintain the required weld quality.

Developing an Improved System for Allocating Support Unit Costs to Business Units

The objective of this study is to develop an improved support unit cost allocation system for a medium-sized technology company, and to examine which options for overhead cost accounting exist. The study begins with presenting the terminology and methods associated with overhead cost accounting and responsibility accounting. Also the most common challenges and resulting benefits of overhead cost allocation system development are brought up. As one research method two case studies were conducted for benchmarking purposes. These external cases are compared with the principal company’s cost allocation system and reflected against the theoretical background. In the empirical section interviews were used as the primary source of information alongside self studying principal company’s old cost allocation method. Interviews revealed the main weaknesses of the old system and proposals for a new one, which were utilized in setting targets for developing the new system. As a result of the development process an improved support unit cost allocation system was realized for year 2009. The new system is able to handle support unit costs in more detail enhancing the transparency and fairness of resulting cost allocations. Parts of support unit costs are now seen as business units’ own costs rather than group-level overhead. Also recommendations for further development are made after analyzing how well the targets were reached.

Treatment of oily wastewater by ultrafiltration: The effect of different operating and solution conditions

In many industries, such as petroleum production, and the petrochemical, metal, food and cosmetics industries, wastewaters containing an emulsion of oil in water are often produced. The emulsions consist of water (up to 90%), oils (mineral, animal, vegetable and synthetic), surfactants and other contaminates. In view of its toxic nature and its deleterious effects on the surrounding environment (soil, water) such wastewater needs to be treated before release into natural water ways. Membrane-based processes have successfully been applied in industrial applications and are considered as possible candidates for the treatment of oily wastewaters. Easy operation, lower cost, and in some cases, the ability to reduce contaminants below existing pollution limits are the main advantages of these systems. The main drawback of membranes is flux decline due tofouling and concentration polarisation. The complexity of oil-containing systems demands complementary studies on issues related to the mitigation of fouling and concentration polarisation in membranebased ultrafiltration. In this thesis the effect of different operating conditions (factors) on ultrafiltration of oily water is studied. Important factors are normally correlated and, therefore, their effect should be studied simultaneously. This work uses a novel approach to study different operating conditions, like pressure, flow velocity, and temperature, and solution properties, like oil concentration (cutting oil, diesel, kerosene), pH, and salt concentration (CaCl2 and NaCl)) in the ultrafiltration of oily water, simultaneously and in a systematic way using an experimental design approach. A hypothesis is developed to describe the interaction between the oil drops, salt and the membrane surface. The optimum conditions for ultrafiltration and the contribution of each factor in the ultrafiltration of oily water are evaluated. It is found that the effect on permeate flux of the various factors studied strongly depended on the type of oil, the type of membrane and the amount of salts. The thesis demonstrates that a system containing oil is very complex, and that fouling and flux decline can be observed even at very low pressures. This means that only the weak form of the critical flux exists for such systems. The cleaning of the fouled membranes and the influence of different parameters (flow velocity, temperature, time, pressure, and chemical concentration (SDS, NaOH)) were evaluated in this study. It was observed that fouling, and consequently cleaning, behaved differently for the studied membranes. Of the membranes studied, the membrane with the lowest propensity for fouling and the most easily cleaned was the regenerated cellulose membrane (C100H). In order to get more information about the interaction between the membrane and the components of the emulsion, a streaming potential study was performed on the membrane. The experiments were carried out at different pH and oil concentration. It was seen that oily water changed the surface charge of the membrane significantly. The surface charge and the streaming potential during different stages of filtration were measured and analysed being a new method for fouling of oil in this thesis. The surface charge varied in different stages of filtration. It was found that the surface charge of a cleaned membrane was not the same as initially; however, the permeability was equal to that of a virgin membrane. The effect of filtration mode was studied by performing the filtration in both cross-flow and deadend mode. The effect of salt on performance was considered in both studies. It was found that salt decreased the permeate flux even at low concentration. To test the effect of hydrophilicity change, the commercial membranes used in this thesis were modified by grafting (PNIPAAm) on their surfaces. A new technique (corona treatment) was used for this modification. The effect of modification on permeate flux and retention was evaluated. The modified membranes changed their pore size around 33oC resulting in different retention and permeability. The obtained results in this thesis can be applied to optimise the operation of a membrane plant under normal or shock conditions or to modify the process such that it becomes more efficient or effective.

Strategic Development of Electricity Distribution Networks – Concept and Methods

Strategic development of distribution networks plays a key role in the asset management in electricity distribution companies. Owing to the capital-intensive nature of the field and longspan operations of companies, the significance of a strategy is emphasised. A well-devised strategy combines awareness of challenges posed by the operating environment and the future targets of the distribution company. Economic regulation, ageing infrastructure, scarcity of resources and tightening supply requirements with challenges created by the climate change put a pressure on the strategy work. On the other hand, technology development related to network automation and underground cabling assists in answering these challenges. This dissertation aims at developing process knowledge and establishing a methodological framework by which key issues related to network development can be addressed. Moreover, the work develops tools by which the effects of changes in the operating environment on the distribution business can be analysed in the strategy work. To this end, the work discusses certain characteristics of the distribution business and describes the strategy process at a principle level. Further, the work defines the subtasks in the strategy process and presents the key elements in the strategy work and long-term network planning. The work delineates the factors having either a direct or indirect effect on strategic planning and development needs in the networks; in particular, outage costs constitute an important part of the economic regulation of the distribution business, reliability being thus a key driver in network planning. The dissertation describes the methodology and tools applied to cost and reliability analyses in the strategy work. The work focuses on determination of the techno-economic feasibility of different network development technologies; these feasibility surveys are linked to the economic regulation model of the distribution business, in particular from the viewpoint of reliability of electricity supply and allowed return. The work introduces the asset management system developed for research purposes and to support the strategy work, the calculation elements of the system and initial data used in the network analysis. The key elements of this asset management system are utilised in the dissertation. Finally, the study addresses the stages of strategic decision-making and compilation of investment strategies. Further, the work illustrates implementation of strategic planning in an actual distribution company environment.