A three dimensional study of heat transfer in a supercritical circulating fluidized bed combustor

From the boiler design point of view, it is imperative to know and understand the operation of the boiler. Since comprehensive measurement of a large furnace is impossible, the furnace can be modeled in order to study its behavior and phenomena. This requires the used model to be validated to correspond with the physical furnace behavior. In this thesis, a three dimensional furnace model is validated to match a bituminous coal utilizing, supercritical once-through circulating fluidized bed combustor based on measurement data. The validated model is used for analyzing the furnace heat transfer. Other heat transfer analysis methods are energy balance method based on tube surface temperature measurements and a method based on measured temperature difference between the tube crest and the fin. The latter method was developed in the thesis using Fluent-software. In the theory part, literature is reviewed and the fundamental aspects of circulating fluidized bed are discussed. These aspects are solid particle behavior in fluidization known as hydrodynamics, behavior of fuel and combustion and heat transfer. Fundamental aspects of modeling are also presented.

Water circulations for effective bleaching of high-brightness mechanical pulps

The amount of water available is usually restricted, which leads to a situation where a complete understanding of the process, including water circulations and the influence of water components, is essential. The main aim of this thesis was to clarify the possibilities for the efficient use of residual peroxide by means of water circulation rearrangements. Rearranging water circulations and the reduction of water usage may cause new problems, such as metal induced peroxide decomposition that needs to be addressed. This thesis introduces theoretical methods of water circulations to combine two variables; effective utilization of residual peroxide and avoiding manganese in the alkaline peroxide bleaching stage. Results are mainly based on laboratory and mill site experiments concerning the utilization of residual peroxide. A simulation model (BALAS) was used to evaluate the manganese contents and residual peroxide doses. It was shown that with optimum recirculation of residual peroxide the brightness can be improved or chemical costs can be decreased. From the scientific perspective, it was also very important to discover that recycled peroxide was more effective pre-bleaching agent compared to fresh peroxide. This can be due to the organic acids i.e. per acetic acid in wash press filtrate that have been formed in alkaline bleaching stage. Even short retention time was adequate and the activation of residual peroxide using sodium hydroxide was not necessary. There are several possibilities for using residual peroxide in practice regarding bleaching. A typical modern mechanical pulping process line consist of defibering, screening, a disc filter, a bleach press, high consistency (HC) peroxide bleaching and a wash press. Furthermore there usually is not a particular medium consistency (MC) pre-bleaching stage that includes additional thickening equipment. The most advisable way to utilize residual peroxide in this kind of process is to recycle the wash press filtrate to the dilution of disc filter pulp (low MC pre-bleaching stage). An arrangement such as this would be beneficial in terms of the reduced convection of manganese to the alkaline bleaching stage. Manganese originates from wood material and will be removed to the water phase already in the early stages of the process. Recycling residual peroxide prior to the disc filter is not recommended because of low consistencies. Regarding water circulations, the novel point of view is that, it would be beneficial to divide water circulations into two sections and the critical location for the division is the disc filter. Both of these two sections have their own priority. Section one before the disc filter: manganese removal. Section two after the disc filter: brightening of pulp. This division can be carried out if the disc filter pulp is diluted only by wash press filtrate before the MC storage tower. The situation is even better if there is an additional press after the disc filter, which will improve the consistency of the pulp. This has a significant effect on the peroxide concentration in the MC pre-bleaching stage. In terms of manganese content, it is essential to avoid the use of disc filter filtrate in the bleach press and wash press showers. An additional cut-off press would also be beneficial for manganese removal. As a combination of higher initial brightness and lower manganese content, the typical brightness increase varies between approximately 0.5 and 1% ISO units after the alkaline peroxide bleaching stage. This improvement does not seem to be remarkable, but as it is generally known, the final brightness unit is the most expensive and difficult to achieve. The estimation of cost savings is not unambiguous. For example in GW/TMP mill case 0.6% ISO units higher final brightness gave 10% savings in the costs of bleaching chemicals. With an hypothetical 200 000 ton annual production, this means that the mill could save in the costs of bleaching chemicals more than 400 000 euros per year. In general, it can be said that there were no differences between the behavior of different types of processes (GW, PGW, TMP and BCTMP). The enhancement of recycling gave a similar response in all cases. However, we have to remember that the utilization of residual peroxide in older mills depends a great deal on the process equipment, the amount of water available and existing pipeline connections. In summary, it can be said that processes are individual and the same solutions cannot be applied to all cases.

Factors affecting the usability of aspen (Populus tremula) wood dried at different temperature levels

In this dissertation the main aim was to study the usability of aspen wood in the mechanical wood processes, especially the factors that affect the usability of aspen wood, which is dried at different temperature levels. The problematic of varying temperatures from level to another seem to have significant effects on distortions. According to the studies conducted, many practical solutions for drying of aspen timber can be made. European aspen sawn timber should be dried in relatively narrow widths, short lengths, edged and sawn pith free. The results achieved give an interesting view for the distortions of aspen wood between HT drying and heat treatment. The most significant result is that cupping seems to decrease when increasing temperature level from HT drying to heat treatment phase. The difference is significant. Other very obvious result is that bow and crook are increasing between these two temperature levels, bow significantly. Also the modelling gives a good background for this result since cupping is reduced by higher temperatures. It can also be assumed that these distortions can be affected for example by sorting out the timber used to different moisture levels before drying. This could be a very simple solution for practical purposes. From practical point of view, it was also noted during the drying tests performed that the discoloration seem to be no problem for aspen boards dried in temperatures under 150 °C. Altogether, this dissertation covers many interesting points of view of factors affecting distortions of wood in different temperature stages. Aspen as species in use of mechanical wood industries seems to be a species suitable for component production. According to the results, the best yield from aspen timber can be achieved in industry that can utilize relatively short components of sawn wood. Results achieved give a significant indication about the factors affecting distortions of wood at different temperature stages of drying, especially considering European aspen.

Characterizing Propionibacterium freudenreichii ssp. shermanii JS and Lactobacillus rhamnosus LC705 as a new probiotic combination: basic properties of JS and pilot in vivo assessment of the combination

Characterizing Propionibacterium freudenreichii ssp. shermanii JS and Lactobacillus rhamnosus LC705 as a new probiotic combination: basic properties of JS and pilot in vivo assessment of the combination Each candidate probiotic strain has to have the documentation for the proper identification with current molecular tools, for the biological properties, for the safety aspects and for the health benefits in human trials if the intention is to apply the strain as health promoting culture in the commercial applications. No generalization based on species properties of an existing probiotic are valid for any novel strain, as strain specific differences appear e.g. in the resistance to GI tract conditions and in health promoting benefits (Madsen, 2006). The strain evaluation based on individual strain specific probiotic characteristics is therefore the first key action for the selection of the new probiotic candidate. The ultimate goal in the selection of the probiotic strain is to provide adequate amounts of active, living cells for the application and to guarantee that the cells are physiologically strong enough to survive and be biologically active in the adverse environmental conditions in the product and in GI tract of the host. The in vivo intervention studies are expensive and time consuming; therefore it is not rational to test all the possible candidates in vivo. Thus, the proper in vitro studies are helping to eliminate strains which are unlikely to perform well in vivo. The aims of this study were to characterize the strains of Propionibacterium freudenreichii ssp. shermanii JS and Lactobacillus rhamnosus LC705, both used for decades as cheese starter cultures, for their technological and possible probiotic functionality applied in a combined culture. The in vitro studies of Propionibacterium freudenreichii ssp. shermanii JS focused on the monitoring of the viability rates during the acid and bile treatments and on the safety aspects such as antibiotic susceptibility and adhesion. The studies with the combination of the strains JS and LC705 administered in fruit juices monitored the survival of the strains JS and LC705 during the GI transit and their effect on gut wellbeing properties measured as relief of constipation. In addition, safety parameters such as side effects and some peripheral immune parameters were assessed. Separately, the combination of P. freudenreichii ssp. shermanii JS and Lactobacillus rhamnosus LC705 was evaluated from the technological point of view as a bioprotective culture in fermented foods and wheat bread applications. In this study, the role ofP. freudenreichii ssp. shermanii JS as a candidate probiotic culture alone and in a combination with L. rhamnosus LC705 was demonstrated. Both strains were transiently recovered in high numbers in fecal samples of healthy adults during the consumption period. The good survival through the GI transit was proven for both strains with a recovery rate from 70 to 80% for the JS strain and from 40 to 60% for the LC705 strain from the daily dose of 10 log10 CFU. The good survival was shown from the consumption of fruit juices which do not provide similar matrix protection for the cells as milk based products. The strain JS did not pose

Space–Time Block Codes and the Complexity of Sphere Decoding

In wireless communications the transmitted signals may be affected by noise. The receiver must decode the received message, which can be mathematically modelled as a search for the closest lattice point to a given vector. This problem is known to be NP-hard in general, but for communications applications there exist algorithms that, for a certain range of system parameters, offer polynomial expected complexity. The purpose of the thesis is to study the sphere decoding algorithm introduced in the article On Maximum-Likelihood Detection and the Search for the Closest Lattice Point, which was published by M.O. Damen, H. El Gamal and G. Caire in 2003. We concentrate especially on its computational complexity when used in space–time coding. Computer simulations are used to study how different system parameters affect the computational complexity of the algorithm. The aim is to find ways to improve the algorithm from the complexity point of view. The main contribution of the thesis is the construction of two new modifications to the sphere decoding algorithm, which are shown to perform faster than the original algorithm within a range of system parameters.

Demographic Modelling of Human Population Growth

This work presents models and methods that have been used in producing forecasts of population growth. The work is intended to emphasize the reliability bounds of the model forecasts. Leslie model and various versions of logistic population models are presented. References to literature and several studies are given. A lot of relevant methodology has been developed in biological sciences. The Leslie modelling approach involves the use of current trends in mortality,fertility, migration and emigration. The model treats population divided in age groups and the model is given as a recursive system. Other group of models is based on straightforward extrapolation of census data. Trajectories of simple exponential growth function and logistic models are used to produce the forecast. The work presents the basics of Leslie type modelling and the logistic models, including multi- parameter logistic functions. The latter model is also analysed from model reliability point of view. Bayesian approach and MCMC method are used to create error bounds of the model predictions.

Estimation of existing cable systems in generator-busbar unit and choice the optimal solution for its modernization

The aim of this master’s thesis is to develop an algorithm to calculate the cable network for heat and power station CHGRES. This algorithm includes important aspect which has an influence on the cable network reliability. Moreover, according to developed algorithm, the optimal solution for modernization cable system from economical and technical point of view was obtained. The conditions of existing cable lines show that replacement is necessary. Otherwise, the fault situation would happen. In this case company would loss not only money but also its prestige. As a solution, XLPE single core cables are more profitable than other types of cable considered in this work. Moreover, it is presented the dependence of value of short circuit current on number of 10/110 kV transformers connected in parallel between main grid and considered 10 kV busbar and how it affects on final decision. Furthermore, the losses of company in power (capacity) market due to fault situation are presented. These losses are commensurable with investment to replace existing cable system.

Heating control of an electrical motor

Electrical motors on a ship attackable to different factors which decrease these lifetimes. One of the main external factors on a ship which usually is a reason of the motor failure is a moisture condensation which decreases the motor winding insulation and increase a probability of the short circuit. Therefore, the protection against moisture is necessary for ship electrical motors. The motor should be protected against moisture all time when it does not operate. The necessity of such protection requires a lot of energy consumption. This master’s thesis is focused on the creation of the electrical motor thermal model and on the different methods of the motor protection against moisture analysis with energy consumption point of view.

The determination of EONIA rate: The impact of the financial crisis and the effects of the changes in the monetary policy implementation framework

EONIA is a market based overnight interest rate, whose role as the starting point of the yield curve makes it critical from the perspective of the implementation of European Central Bank´s common monetary policy in the euro area. The financial crisis that started in 2007 had a large impact on the determination mechanism of this interest rate, which is considered as the central bank´s operational target. This thesis examines the monetary policy implementation framework of the European Central Bank and changes made to it. Furthermore, we discuss the development of the recent turmoil in the money market. EONIA rate is modelled by means of a regression equation using variables related to liquidity conditions, refinancing need, auction results and calendar effects. Conditional volatility is captured by an EGARCH model, and autocorrelation is taken into account by employing an autoregressive structure. The results highlight how the tensions in the initial stage of the market turmoil were successfully countered by ECB´s liquidity policy. The subsequent response of EONIA to liquidity conditions under the full allotment liquidity provision procedure adopted after the demise of Lehman Brothers is also established. A clear distinction in the behavior of the interest rate between the sub-periods was evident. In the light of the results obtained, some of the challenges posed by the exit-strategy implementation will be addressed.

Traffic flow development at North European company level with respect of China and Russia

The aim of the thesis is to analyze traffic flows and its development from North European companies` point of view to China and Russia using data from logistics questionnaire. Selected North European companies are large Finnish and Swedish companies. The questionnaire was sent via email to the target group. The study is based on the answers got from respondent companies from years 2006, 2009 and 2010. In the thesis Finnish Talouselämä newspaper and Swedish Affärsdata are used as a database to find the target companies for the survey. Respondents were most often logistics managers in companies. In the beginning of the thesis concepts of transportation logistics is presented, including container types, trade terms, axel loads in roads and in railways. Also there is information about warehousing types and terminals. After that, general information of Chinese and Russian transportation logistics is presented. Chinese and Russian issues are discussed in two sections. In both of them it is analyzed economic development, freight transport and trade balance. Some practical examples of factory inaugurations in China and Russia are presented that Finnish and Swedish companies have completed. In freight transport section different transportation modes, logistics outsourcing and problems of transportation logistics is discussed. The results of the thesis show that transportation flows between Europe and China is changing. Freight traffic from China to European countries will strengthen even more from the current base. When it comes to Russia and Europe, traffic flows seem to be changing from eastbound traffic to westbound traffic. It means that in the future it is expected more freight traffic from Russia to Europe. Some probable reasons for that are recent factory establishments in Russia and company interviews support also this observation. Effects of the economic recession are mainly seen in the lower transportation amounts in 2009.

Simulation of hydrogen peroxide direct synthesis in a microreactor

A set of models in Aspen plus was built to simulate the direct synthesis process of hydrogen peroxide in a micro-reactor system. This process model can be used to carry out material balance calculation under various experimental conditions. Three thermodynamic property methods were compared by calculating gas solubility and Uniquac-RK method was finally selected for process model. Two different operation modes with corresponding operation conditions were proposed as the starting point of future experiments. Simulations for these two modes were carried out to get the information of material streams. Moreover, some hydrodynamic parameters such as gas/liquid superficial velocity, gas holdup were also calculated with improved process model. These parameters proved the proposed experimental conditions reasonable to some extent. The influence of operation conditions including temperature, pressure and circulation ratio was analyzed for the first operation mode, where pure oxygen was fed into dissolving tank and hydrogen-carbon dioxide mixture was fed into microreactor directly. The preferred operation conditions for the system are low temperature (2°C) and high pressure (30 bar) in dissolving tank. High circulation ratio might be good in the sense that more oxygen could be dissolved and fed into reactor for reactions, but meanwhile hydrodynamics of microreactor should be considered. Furthermore, more operation conditions of reactor gas/liquid feeds in both of two operation modes were proposed to provide guidance for future experiment design and corresponding hydrodynamic parameters were also calculated. Finally, safety issue was considered from thermodynamic point of view and there is no explosion danger at given experimental plan since the released reaction heat will not cause solvent vaporization inside the microchannels. The improvement of process model still needs further study based on the future experimental results.

Dialogue in the crisis of representation : realism and antirealism in the context of the conversation between theologians and quantum physicists in Göttingen 1949-1961

The aim of this study is to analyse the content of the interdisciplinary conversations in Göttingen between 1949 and 1961. The task is to compare models for describing reality presented by quantum physicists and theologians. Descriptions of reality indifferent disciplines are conditioned by the development of the concept of reality in philosophy, physics and theology. Our basic problem is stated in the question: How is it possible for the intramental image to match the external object?Cartesian knowledge presupposes clear and distinct ideas in the mind prior to observation resulting in a true correspondence between the observed object and the cogitative observing subject. The Kantian synthesis between rationalism and empiricism emphasises an extended character of representation. The human mind is not a passive receiver of external information, but is actively construing intramental representations of external reality in the epistemological process. Heidegger's aim was to reach a more primordial mode of understanding reality than what is possible in the Cartesian Subject-Object distinction. In Heidegger's philosophy, ontology as being-in-the-world is prior to knowledge concerning being. Ontology can be grasped only in the totality of being (Dasein), not only as an object of reflection and perception. According to Bohr, quantum mechanics introduces an irreducible loss in representation, which classically understood is a deficiency in knowledge. The conflicting aspects (particle and wave pictures) in our comprehension of physical reality, cannot be completely accommodated into an entire and coherent model of reality. What Bohr rejects is not realism, but the classical Einsteinian version of it. By the use of complementary descriptions, Bohr tries to save a fundamentally realistic position. The fundamental question in Barthian theology is the problem of God as an object of theological discourse. Dialectics is Barth¿s way to express knowledge of God avoiding a speculative theology and a human-centred religious self-consciousness. In Barthian theology, the human capacity for knowledge, independently of revelation, is insufficient to comprehend the being of God. Our knowledge of God is real knowledge in revelation and our words are made to correspond with the divine reality in an analogy of faith. The point of the Bultmannian demythologising programme was to claim the real existence of God beyond our faculties. We cannot simply define God as a human ideal of existence or a focus of values. The theological programme of Bultmann emphasised the notion that we can talk meaningfully of God only insofar as we have existential experience of his intervention. Common to all these twentieth century philosophical, physical and theological positions, is a form of anti-Cartesianism. Consequently, in regard to their epistemology, they can be labelled antirealist. This common insight also made it possible to find a common meeting point between the different disciplines. In this study, the different standpoints from all three areas and the conversations in Göttingen are analysed in the frameworkof realism/antirealism. One of the first tasks in the Göttingen conversations was to analyse the nature of the likeness between the complementary structures inquantum physics introduced by Niels Bohr and the dialectical forms in the Barthian doctrine of God. The reaction against epistemological Cartesianism, metaphysics of substance and deterministic description of reality was the common point of departure for theologians and physicists in the Göttingen discussions. In his complementarity, Bohr anticipated the crossing of traditional epistemic boundaries and the generalisation of epistemological strategies by introducing interpretative procedures across various disciplines.

Palveluyrityksen brändin vaikutus ostopäätökseen b2b-markkinoilla

Tutkimuksen tavoitteena on kuvata brändin olemusta ja menestystekijöitä ja ymmärtää palveluyrityksen brändin vaikutus ostotilanteessa b2b-markkinoilla. Tutkittavaa ongelmaa lähestytään teoreettisen ja empiirisen tutkimuksen kautta. Empiirisen näkökulman tutkimukseen tuo case-yritys, monipalveluyhtiö Barona, jonka brändin merkitystä ostotilanteessa b2b-markkinoilla tutkimuksessa arvioidaan. Tutkimuksen pääongelma on seuraava: Miten palveluyrityksen brändi vaikuttaa ostopäätökseen b2b-markkinoilla? Tutkimuksen lähestymistapa on kvalitatiivinen eli laadullinen. Tutkimusstrategia on case- eli tapaustutkimus ja tutkimusmenetelmänä on käytetty teemahaastattelua. Brändikokemuksen syntymistä ja sen vaikutusta ostopäätökseen tarkastellaan empiriaosiossa asiakkaan ja brändin hallinnoijan, eli Baronan, näkökulmasta. Tutkimuksen tulokset tukevat sitä olettamusta, että palveluyrityksen brändillä on vaikutusta ostopäätöksessä myös b2b-markkinoilla. Brändit b2b-markkinoilla ovat saaneet kuluttajamarkkinoita vähemmän huomiota, sillä brändien vaikutus ostopäätöksessä koetaan irrationaaliseksi tekijäksi, ja yritysmarkkinoilla ostajien on ajateltu tekevän päätökset täysin rationaalisin perustein. Myös b2b-markkinoilla on päätöksentekijänä kuitenkin yksilö, ei organisaatio. Palvelua ostaessaan ostaja perustelee valintansa järkisyillä, kuten laadulla. Todelliset syyt hankintaan voivat kuitenkin olla hyvin toisenlaiset, kuten brändin status, menestys tai arvostus. Brändi on merkittävässä asemassa myös b2b-asiakkaan ostopäätösprosessissa, varsinkin silloin, kun erottautuminen on vaikeaa. Siinä missä palvelu itsessään lunastaa lupaustaan käyttäjälle, brändi tuottaa lisäarvoa yli palvelun toiminnallisen tarkoituksen. Brändi saa palvelun vaikuttamaan paremmalta. Tietynmerkkisen palvelun nähdessään asiakas odottaa sen tarjoavan tietyt asiat. Asiakas haluaa luottaa siihen, että laatu pysyy samana, eikä palvelua tarvitse joka kerta arvioida erikseen. Asiakas ostaa brändiin sisältyviä laatulupauksia omien tarpeidensa täyttämiseksi tehden valintansa sen perusteella, mitä hyötyä ja arvoa hän odottaa saavansa rahojensa vastineeksi.

Packaging concept development for an assortment of medical device products

Diplomityön tavoitteena oli kehittää Wipak Oy:n valmistamille sterilointipakkauksille tulevaisuuden pakkauskonsepti. Sterilointipakkaukset luokitellaan lääkelaitedirektiivin mukaan lisätarvikkeiksi luokan 1 lääkelaitteille, ja tämä näkökulma oli vahvasti mukana konseptin kehityksessä. Lähtökohtana pakkauskonseptin suunnittelulle oli tuotteiden arvoketjussa, eli pakata tuotteet siten että pakkausten avulla voidaan tuottaa lisäarvoa arvoketjun toimijoille. Tavoitteena oli parantaa pakkausten viestintää, toimivuutta/tehokkuutta toimitusketjussa sekä vahvistaa brändin imagoa myynti- ja kuljetuspakkauksen avulla. Lääkinnälliset laitteet ja tarvikkeet ovat lainsäädännön ja normien avulla tarkasti säädeltyjä. Näiden normien vaatimukset asettavat perusteet myynti- ja kuljetuspakkausten kehittämiselle. Tämän lisäksi suunnittelussa on huomioitu asiakkaiden toiveet ja kehitystarpeet. Kirjallisuusosuudessa on keskitytty lääkinnällisten laitteiden pakkausyksiköiden toimintoihin sekä niiden kehitysnäkymiin. Pääpaino on ollut pakkausmerkintöjen ja jäljitettävyyden kehittämisellä, koska tietojen automaattisen tunnistuksen hyödyntäminen lääkintälaitteiden pakkausten arvoketjussa on kasvava trendi. Manuaalisesti tehtävät tuotevirtojen kirjaukset ketjun eri toimijoiden osalta lisäävät riskejä jäljitettävyyden kannalta ja aiheuttavat lisätyötä ja – kustannuksia ketjun kaikille osapuolille. Ehdotus uudesta pakkauskonseptista on kehitetty näiden tietojen pohjalta. Ehdotuksessa on huomioitu lainsäädännöstä ja ketjun toimijoilta tulevat tarpeet, sekä alan tulevaisuuden kehitysnäkymät. Ehdotetun pakkauskonseptin avulla saadaan lisättyä myynti- ja kuljetuspakkausten tehokkuutta, parannettua jäljitettävyyttä ja helpotettu arvoketjun alavirran toimijoiden työtä lisäämällä erillinen sisäpakkaus myyntiyksikön sisälle. Työssä on lisäksi selvitetty pakkauskonseptin kustannusvaikutukset tuotteiden hintaan. Lopussa on ehdotettu jatkotoimenpiteet suunnitelman implementoimisesta käytäntöön.

Integrating eco-innovation principles into regional strategy and policy: case of Päijät-Häme region, Finland

This study focuses on the integration of eco-innovation principles into strategy and policy at the regional level. The importance of regions as a level for integrating eco-innovative programs and activities served as the point of interest for this study. Eco-innovative activities and technologies are seen as means to meet sustainable development objective of improving regions’ quality of life. This study is conducted to get an in-depth understanding and learning about eco-innovation at regional level, and to know the basic concepts that are important in integrating eco-innovation principles into regional policy. Other specific objectives of this study are to know how eco-innovation are developed and practiced in the regions of the EU, and to analyze the main characteristic features of an eco-innovation model that is specifically developed at Päijät-Häme Region in Finland. Paijät-Häme Region is noted for its successful eco-innovation strategies and programs, hence, taken as casework in this study. Both primary (interviews) and secondary data (publicly available documents) are utilized in this study. The study shows that eco-innovation plays an important role in regional strategy as reviewed based on the experience of other regions in the EU. This is because of its localized nature which makes it easier to facilitate in a regional setting. Since regional authorities and policy-makers are normally focused on solving its localized environmental problems, eco-innovation principles can easily be integrated into regional strategy. The case study highlights Päijät-Häme Region’s eco-innovation strategies and projects which are characterized by strong connection of knowledge-producing institutions. Policy instruments supporting eco-innovation (e.g. environmental technologies) are very much focused on clean technologies, hence, justifying the formation of cleantech clusters and business parks in Päijät-Häme Region. A newly conceptualized SAMPO model of eco-innovation has been developed in Päijät-Häme Region to better capture the region’s characteristics and to eventually replace the current model employed by the Päijät-Häme Regional Authority. The SAMPO model is still under construction, however, review of its principles points to some of its three important spearheads – practice-based innovation, design (eco-design) and clean technology or environmental technology (environment).