Influence of Heat Treatment on Strength Properties of Finger-jointed Components

The purpose for the thesis was to study the thermo treatment of finger-jointed wood. The thesis concentrated on examining the tensile and bending strength of finger-jointed and thermo treated wood. The aim was to find out how different treatment temperature levels and adhesives influence the strength of wood that has been finger-jointed before heat treatment. Secondary objectives were to examine the influence of the treatment time at one temperature, determine differences in the strength between the joints in heartwood and sapwood, examine the visual appearance of the finger joints after the treatment and establish possibilities to reach a characteristic strength level corresponding to C14. Only minor differences in strength properties were measured between the finger-jointed wood treatments II and III. A greater difference was shown between these two treatment temperatures I, which lead to reduced strength. The average strength of joints glued with adhesive 2 was higher after treatments II and III compared to those glued with the adhesive 1. At the treatment temperature I, the adhesive 1 strength properties were at the same level compared to the adhesive 2 or better. There were not any significant differences.

Kaatopaikkakaasun hyväksikäyttö lietteen kuivauksessa

Tällä hetkellä suuri osa esikäsiteltyjen jätevesilietteiden loppusijoitusvaihtoehdoista ei pysty kattamaan lopullisesti kasvavien lietemäärien loppusijoitustarvetta, mikä lisää lietteen loppusijoitusta kaatopaikoille. Kuitenkin EU:n tiukentuneen jätehuoltolainsäädännön sekä ilmastonlämpenemisen suurien haasteiden vuoksi, kaatopaikoille sijoitettavien jätteiden määrää täytyy pyrkiä vähentämään. Tämän työn tavoitteena on tutkia jätevedenpuhdistamoilta tulevan lietteen termistä kuivausta yhtenä lietteenkäsittely vaihtoehtona. Tavoitteena on selvittää voidaanko lietettä kuivaamalla saada liete paremmin hyödynnetyksi. Työssä tarkasteltiin yleisesti yhdyskuntalietteen termisessä kuivaamisessa nykyisin käytettäviä menetelmiä, sen ympäristövaikutuksia, energian tarvetta ja kustannuksia sekä siitä saatavaa hyötyä lietteen loppusijoittamisessa. Lisäksi arvioitiin kuinka kaatopaikkakaasun hyödyntäminen soveltuisi lietteen kuivauksessa tarvittavan energian tuotantoon. Työssä tehdyn selvityksen mukaan kaatopaikkakaasua voidaan hyödyntää suhteellisen helposti lämmöntuotannossa ilman merkittäviä laitosmuutoksia tai kaasun puhdistusta. Ongelmana pidettiin kaatopaikkakaasun kuljetuksia, joka on suhteellisen vaikeaa ja taloudellisesti kannattamatonta. Kuitenkin noin 10 km välimatkan säteellä kaatopaikasta sen hyödyntäminen olisi mahdollista. Työn laskelmien mukaan Suomessa hukkaan poltetulla kaatopaikkakaasulla voitaisiin kuivata noin 250 tuhatta tonnia lietettä vuosittain.

Kehittyneiden ydinpolttoainekiertojen ympäristövaikutusten ja taloudellisuuden arviointia

Kaikkein yleisin käytössä oleva ydinpolttoainekierto on nykyisin avoin, jossa käytetty ydinpolttoaine loppusijoitetaan suoraan ilman jälleenkäsittelyä. Nykyisin kehitteillä olevat uuden sukupolven ydinreaktorit ovat kuitenkin pääosin suunniteltu osittain tai kokonaan suljetuille ydinpolttoainekierroille, jossa käytetty polttoaine jälleenkäsitellään ja osa materiaaleista kierrätetään. Tämän työn tavoitteena oli arvioida näitä kehittyneitä ydinpolttoainekiertoja ympäristövaikutusten ja taloudellisuuden suhteen. Työn yleisluonteista vertailua varten valittiin neljä erilaista kehittynyttä polttoainekiertoskenaariota, joita verrattiin avoimeen polttoainekiertoon erilaisten parametrien avulla. Parametreinä käytettiin muun muassa uraanin kulutusta, loppusijoitettavan jätteen määrää, aktiivisuutta ja lämmöntuottoa sekä käytönaikaisten radioaktiivisten päästöjen määrää. Yleislounteisen arvioinnin lisäksi työssä tarkasteltiin polttoainekiertoa myös Suomen näkökulmasta. Nykyistä polttoainekiertoa verrattiin kahteen erilaiseen tulevaisuuden versioon. Kestävän kehityksen osalta kehittyneet polttoainekierrot vähensivät ympäristövaikutusten määrää avoimeen polttoainekiertoon verrattuna. Kehittyneiden polttoainekiertojen kustannukset olivat avoimen polttoainekierron kustannuksia suuremmat. Kokonaiskustannuksissa ero oli kaikilla vertailuskenaarioilla alle 20 %, mutta polttoainekiertokustannuksissa kustannusten kasvu oli välillä 27-45 % riippuen skenaariosta. Suomen tapauksessa tulokset olivat hyvin samankaltaisia. Uraanin kulutus ja loppusijoitettavan jätteen määrä väheni kehittyneempien polttoainekiertojen johdosta. Polttoainekiertokustannukset nousivat noin puolitoistakertaisiksi, mutta vaikutus kokonaiskustannuksiin oli vain noin 10 %. Johtopäätöksenä voidaan todeta, ettäydinpolttoainekierron ympäristövaikutuksia on mahdollista vähentää osittain tai kokonaan suljettujen polttoainekiertojen avulla. Vaikka polttoainekierron kustannukset kasvavat, niiden vaikutus ydinsähkön kokonaiskustannuksiin ei ole niin merkittävä.

Methods for construction and analysis of computational models in systems biology : applications to the modelling of the heat shock response and the self-assembly of intermediate filaments

Systems biology is a new, emerging and rapidly developing, multidisciplinary research field that aims to study biochemical and biological systems from a holistic perspective, with the goal of providing a comprehensive, system- level understanding of cellular behaviour. In this way, it addresses one of the greatest challenges faced by contemporary biology, which is to compre- hend the function of complex biological systems. Systems biology combines various methods that originate from scientific disciplines such as molecu- lar biology, chemistry, engineering sciences, mathematics, computer science and systems theory. Systems biology, unlike “traditional” biology, focuses on high-level concepts such as: network, component, robustness, efficiency, control, regulation, hierarchical design, synchronization, concurrency, and many others. The very terminology of systems biology is “foreign” to “tra- ditional” biology, marks its drastic shift in the research paradigm and it indicates close linkage of systems biology to computer science. One of the basic tools utilized in systems biology is the mathematical modelling of life processes tightly linked to experimental practice. The stud- ies contained in this thesis revolve around a number of challenges commonly encountered in the computational modelling in systems biology. The re- search comprises of the development and application of a broad range of methods originating in the fields of computer science and mathematics for construction and analysis of computational models in systems biology. In particular, the performed research is setup in the context of two biolog- ical phenomena chosen as modelling case studies: 1) the eukaryotic heat shock response and 2) the in vitro self-assembly of intermediate filaments, one of the main constituents of the cytoskeleton. The range of presented approaches spans from heuristic, through numerical and statistical to ana- lytical methods applied in the effort to formally describe and analyse the two biological processes. We notice however, that although applied to cer- tain case studies, the presented methods are not limited to them and can be utilized in the analysis of other biological mechanisms as well as com- plex systems in general. The full range of developed and applied modelling techniques as well as model analysis methodologies constitutes a rich mod- elling framework. Moreover, the presentation of the developed methods, their application to the two case studies and the discussions concerning their potentials and limitations point to the difficulties and challenges one encounters in computational modelling of biological systems. The problems of model identifiability, model comparison, model refinement, model inte- gration and extension, choice of the proper modelling framework and level of abstraction, or the choice of the proper scope of the model run through this thesis.

Role and regulatory mechanisms of heat shock factor 2

Protein homeostasis is essential for cells to prosper and survive. Various forms of stress, such as elevated temperatures, oxidative stress, heavy metals or bacterial infections cause protein damage, which might lead to improper folding and formation of toxic protein aggregates. Protein aggregation is associated with serious pathological conditions such as Alzheimer’s and Huntington’s disease. The heat shock response is a defense mechanism that protects the cell against protein-damaging stress. Its ancient origin and high conservation among eukaryotes suggest that the response is crucial for survival. The main regulator of the heat shock response is the transcription factor heat shock factor 1 (HSF1), which induces transcription of genes encoding protective molecular chaperones. In vertebrates, a family of four HSFs exists (HSF1-4), with versatile functions not only in coping with acute stress, but also in development, longevity and cancer. Thus, knowledge of the HSFs will aid in our understanding on how cells survive suboptimal circumstances, but will also provide insights into normal physiological processes as well as diseaseassociated conditions. In this study, the function and regulation of HSF2 have been investigated. Earlier gene inactivation experiments in mice have revealed roles for HSF2 in development, particularly in corticogenesis and spermatogenesis. Here, we demonstrate that HSF2 holds a role also in the heat shock response and influences stress-induced expression of heat shock proteins. Intriguingly, DNA-binding activity of HSF2 upon stress was dependent on the presence of intact HSF1, suggesting functional interplay between HSF1 and HSF2. The underlying mechanism for this phenomenon could be configuration of heterotrimers between the two factors, a possibility that was experimentally verified. By changing the levels of HSF2, the expression of HSF1-HSF2 heterotrimer target genes was altered, implementing HSF2 as a modulator of HSF-mediated transcription. The results further indicate that HSF2 activity is dependent on its concentration, which led us to ask the question of how accurate HSF2 levels are achieved. Using mouse spermatogenesis as a model system, HSF2 was found to be under direct control of miR-18, a miRNA belonging to the miR-17~92 cluster/Oncomir-1 and whose physiological function had remained unclear. Investigations on spermatogenesis are severely hampered by the lack of cell systems that would mimic the complex differentiation processes that constitute male germ cell development. Therefore, to verify that HSF2 is regulated by miR-18 in spermatogenesis, a novel method named T-GIST (Transfection of Germ cells in Intact Seminiferous Tubules) was developed. Employing this method, the functional consequences of miR-18-mediated regulation in vivo were demonstrated; inhibition of miR- 18 led to increased expression of HSF2 and altered the expression of HSF2 target genes Ssty2 and Speer4a. Consequently, the results link miR-18 to HSF2-mediated processes such as germ cell maturation and quality control and provide miR-18 with a physiological role in gene expression during spermatogenesis.Taken together, this study presents compelling evidence that HSF2 is a transcriptional regulator in the heat shock response and establishes the concept of physical interplay between HSF2 and HSF1 and functional consequences thereof. This is also the first study describing miRNA-mediated regulation of an HSF.

Recovery and refining of manganese as by-product from hydrometallurgical processes

The consumption of manganese is increasing, but huge amounts of manganese still end up in waste in hydrometallurgical processes. The recovery of manganese from multi-metal solutions at low concentrations may not be economical. In addition, poor iron control typically prevents the production of high purity manganese. Separation of iron from manganese can be done with chemical precipitation or solvent extraction methods. Combined carbonate precipitation with air oxidation is a feasible method to separate iron and manganese due to the fast kinetics, good controllability and economical reagents. In addition the leaching of manganese carbonate is easier and less acid consuming than that of hydroxide or sulfide precipitates. Selective iron removal with great efficiency from MnSO4 solution is achieved by combined oxygen or air oxidation and CaCO3 precipitation at pH > 5.8 and at a redox potential of > 200 mV. In order to avoid gypsum formation, soda ash should be used instead of limestone. In such case, however, extra attention needs to be paid on the reagents mole ratios in order to avoid manganese coprecipitation. After iron removal, pure MnSO4 solution was obtained by solvent extraction using organophosphorus reagents, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and bis(2,4,4- trimethylpentyl)phosphinic acid (CYANEX 272). The Mn/Ca and Mn/Mg selectivities can be increased by decreasing the temperature from the commonly used temperatures (40 –60oC) to 5oC. The extraction order of D2EHPA (Ca before Mn) at low temperature remains unchanged but the lowering of temperature causes an increase in viscosity and slower phase separation. Of these regents, CYANEX 272 is selective for Mn over Ca and, therefore, it would be the better choice if there is Ca present in solution. A three-stage Mn extraction followed by a two-stage scrubbing and two-stage sulfuric acid stripping is an effective method of producing a very pure MnSO4 intermediate solution for further processing. From the intermediate MnSO4 some special Mn- products for ion exchange applications were synthesized and studied. Three types of octahedrally coordinated manganese oxide materials as an alternative final product for manganese were chosen for synthesis: layer structured Nabirnessite, tunnel structured Mg-todorokite and K-kryptomelane. As an alternative source of pure MnSO4 intermediate, kryptomelane was synthesized by using a synthetic hydrometallurgical tailings. The results show that the studied OMS materials adsorb selectively Cu, Ni, Cd and K in the presence of Ca and Mg. It was also found that the exchange rates were reasonably high due to the small particle dimensions. Materials are stable in the studied conditions and their maximum Cu uptake capacity was 1.3 mmol/g. Competitive uptake of metals and acid was studied using equilibrium, batch kinetic and fixed-bed measurements. The experimental data was correlated with a dynamic model, which also accounts for the dissolution of the framework manganese. Manganese oxide micro-crystals were also bound onto silica to prepare a composite material having a particle size large enough to be used in column separation experiments. The MnOx/SiO2 ratio was found to affect significantly the properties of the composite. The higher the ratio, the lower is the specific surface area, the pore volume and the pore size. On the other hand, higher amount of silica binder gives composites better mechanical properties. Birnesite and todorokite can be aggregated successfully with colloidal silica at pH 4 and with MnO2/SiO2 weight ratio of 0.7. The best gelation and drying temperature was 110oC and sufficiently strong composites were obtained by additional heat-treatment at 250oC for 2 h. The results show that silica–supported MnO2 materials can be utilized to separate copper from nickel and cadmium. The behavior of the composites can be explained reasonably well with the presented model and the parameters estimated from the data of the unsupported oxides. The metal uptake capacities of the prepared materials were quite small. For example, the final copper loading was 0.14 mmol/gMnO2. According to the results the special MnO2 materials are potential for a specific environmental application to uptake harmful metal ions.

Teurasjätteiden jalostaminen liikennepolttoaineiksi

Työssä määritettiin luokan 2 eläinperäisistä sivutuotteista liikennekäyttöön tuotettujen biodieselin ja biometaanin elinkaaren aikaiset kasvihuonekaasupäästöt ja tuotantoprosessien energiankulutukset perustuen kirjallisuuslähteistä saatuihin lähtötietoihin. Tätä kautta tutkittiin yhdistelmäprosessia, jossa tuotetaan molempia polttoaineita ja selvitettiin onko tällaisella tuotantotavalla mahdollista vähentää päästöjä ja parantaa polttoaineiden tuotannon energiatehokkuutta. Kasvihuone-kaasupäästöjen laskentamenetelmä pohjautuu direktiivissä 2009/28/EY annettuun ohjeistukseen ja eri kasvihuonekaasupäästöjen karakterisointi IPCC:n sadan vuoden tarkastelumalliin. Käytännön laskenta suoritettiin standardien SFS-EN ISO 14040 ja 14044 määrittelemän elinkaariarviointiselvityksen muodossa. Työssä käytetyn laskentamenetelmän ja tarkasteluun valittujen tuotanto-teknologioiden perusteella lasketut tulokset osoittavat, että yhdistelmäprosessilla ei saavuteta suurempia päästövähenemiä eikä parempaa energiatehokkuutta kuin nykyisin käytössä olevilla tuotantotavoilla. Tulokset ovat kuitenkin hyvin herkkiä laskennassa tehtyjen oletusten ja käytettyjen lähtötietojen vaihtelulle sekä valittujen laskentamenetelmien muutoksille. Suurin päästöjä ja energiankulutusta aiheuttava yksittäinen tekijä on kaikissa tuotejärjestelmissä luokan 2 sivutuotteiden esikäsittelyssä vaadittavaan steri-lointiin tarvittavan lämmön tuotanto. Tutkituissa tuotejärjestelmissä lämpö tuotetaan kokonaan tai osittain fossiilisilla polttoaineilla. Kasvihuone-kaasupäästöjä olisi mahdollista alentaa merkittävästi siirtymällä lämmön tuotannossa kokonaan uusiutuviin polttoaineisiin. Sterilointi on lain edellyttämä käsittelytapa ja siksi energiankulutusta on vallitsevissa olosuhteissa hyvin vaikea pienentää merkittävästi.

Waste Stream Investigation from Perspective of Changing Waste Legislation at Green Sand Foundries

The update of the Finnish legislation concerning waste was unavoidable, to comply with the European Union (EU) requirements defined in the EU-Directive on Waste. The new waste law updates were enacted into the Finnish legislation on the 11.03.2011 and targeted for applicability by the 11.03.2012. This thesis investigates the implications of the new amendments to the waste legislation from the perspective of green sand foundries. The investigations are conducted by comparing two of Componenta’s green sand foundries and evaluating their waste streams. Additionally, the impacts of legislation amendments are critiqued on their environmental and economic aspects. The study’s comparison of waste fractions at the two foundries reveals that sand is dominant in absolute tonnage and costs. The increments of waste taxes forces foundries to focus on waste management, recycling and disposing. The new legislation’s promotion of material efficiency, also guides foundries towards the prevention of waste. A potential preventive measure is to regenerate waste sand resulting to cost savings on both raw-materials and waste management. However, the lack of absolute targets for waste prevention or recycling rates discourages the interests towards creating or adopting new technologies and methods for the waste handling.

Public-private partnership in marine litter waste management

Marine litter is an international environmental problem that causes considerable costs to coastal communities and the fishing industry. Several international and national treaties and regulations have provisions to marine litter and forbid disposal of waste into the sea. However, none of these regulations state a responsibility for public authorities to recover marine litter from the sea, like they do for marine litter that washes up on public beaches. In a financial evaluation of a value chain for marine litter incineration it was found out that the total costs of waste incineration are approximately 100 ─ 200 % higher than waste fees offered by waste contractors of ports. The high costs of incineration are derived from the high calorific value of marine litter and therefore a high incineration cost for the waste, and long distances between ports that are taking part in a project for marine litter recovery from the sea and an Energy-from-Waste (EfW) facility. This study provides a possible solution to diverting marine litter from landfills to more environmentally sustainable EfW use by using a public-private partnership (PPP) framework. PPP would seem to fit as a suitable cooperative approach for answering problems of current marine litter disposal in theory. In the end it is up to the potential partners of this proposed PPP to decide whether the benefits of cooperation justify the required efforts.

Fundamentals of heat transfer

Following over 170+ pages and additional appendixes are formed based on content of Course: Fundamentals of Heat Transfer. Mainly this summarizes relevant parts on Book of Fundamentals of Heat and Mass Transfer (Incropera), but also other references introducing the same concepts are included. Student’s point of view has been consideredwith following highlights: (1) Relevant topics are presented in a nutshell to provide fast digestion of principles of heat transfer. (2) Appendixes include terminology dictionary. (3) Totally 22 illustrating examples are connecting theory to practical applications and quantifying heat transfer to understandable forms as: temperatures, heat transfer rates, heat fluxes, resistances and etc. (4) Most important Learning outcomes are presented for each topic separately. The Book, Fundamentals of Heat and Mass Transfer (Incropera), is certainly recommended for those going beyond basic knowledge of heat transfer. Lecture Notes consists of four primary content-wise objectives: (1) Give understanding to physical mechanisms of heat transfer, (2)Present basic concepts and terminology relevant for conduction, convection and radiation (3) Introduce thermal performance analysis methods for steady state and transient conduction systems. (4) Provide fast-to-digest phenomenological understanding required for basic design of thermal models

Mädätysjäännöksen rakeistus, terminen kuivaus ja energiahyötykäyttö

Tutkimuksen tavoitteena oli kartoittaa alueellisen jäteyhtiön Kymenlaakson Jäte Oy:n mahdollisuuksia rakeistaa ja termisesti kuivata mekaanisesti kuivattua mädätysjäännöstä sekä mahdollisuuksia toimittaa termisesti kuivattua materiaalia energiahyötykäyttöön. Tutkimuksessa selvitettiin myös kokemuksia lattialämmityksen käyttämisestä mädätysjäännöksen kuivaukseen. Tutkimuksessa perehdyttiin erilaisiin rakeistus- ja kuivausmenetelmiin sekä termisen kuivurin valintaan vaikuttaviin asioihin. Kuvaukset perustuvat kirjallisuudesta ja internetistä saatuihin tietoihin. Tekniikkakuvausten pohjalta lähdettiin kyselemään tarjouksia termisiä kuivauslaitteistoja myyviltä yrityksiltä. Tarjoukset pyydettiin kuiva-ainepitoisuuden muutokselle 30 %:sta 90 %:iin ja oletettiin, että kuivaukseen on käytettävissä lämpöä viideltä kaatopaikkakaasua käyttävältä mikroturbiinilta. Tutkimuksen aikana saatiin tarjous kuudelta yritykseltä. Saadut tarjoukset esiteltiin tiivistetysti raportissa ja kokonaisuudessaan ne sisällytettiin Kymenlaakson Jäte Oy:n laajempaan raporttiin, joka ei ole julkinen. Yritykset antoivat hyvin erilaisia tietoja siitä, mitä tarjoukseen sisältyy, joten tarjoukset eivät olleet suoraan vertailukelpoisia. Tarjouksista myös havaittiin, että jos Mäkikylän biokaasulaitokselta vastaanotettaisiin enimmäismäärä (19 500 t/a) mädätysjäännöstä, mikroturbiineilta saatava lämpömäärä ei riittäisi kuivaamaan kaikkea mädätysjäännöstä 90 % kuiva-ainepitoisuuteen. Tutkimuksen aikana huomattiin myös, että sitovan tarjouksen saamiseksi mädätysjäännös tulee toimittaa testattavaksi, jolloin saadaan vahvistus kuivausmenetelmän soveltuvuudesta kyseiselle materiaalille. Tutkimuksessa selvitettiin myös, minkälaisia kokemuksia löytyy lattialämmityksen käyttämisestä kuivaukseen niin Suomesta kuin maailmalta ja voiko menetelmää käyttää mädätysjäännöksen kuivaukseen. Kyseistä menetelmää on käytetty tehostamaan aurinkokuivausta, joten tutkimuksen aikana perehdyttiin erityisesti aurinkokuivaukseen liittyviin tieteellisiin artikkeleihin. Lattialämmityksen käytöstä löytyi niin heikkouksia kuin vahvuuksia. Suomessa aurinkokuivauksen ja lattialämmityksen yhdistelmä ei ole kuitenkaan päätynyt laajaan käyttöön ja syynä voidaan nähdä muun muassa kylmät ja pimeät vuodenajat sekä suuri pinta-alan tarve. Tutkimusraportissa selvitettiin lisäksi polttolaitosten edustajien kiinnostusta ja rajoituksia ottaa vastaan termisesti kuivattua mädätysjäännöstä. Tutkimuksen aikana otettiin yhteyttä alle 100 km etäisyydellä Kymenlaakson Jäte Oy:stä sijaitsevien jätteenpolttoluvan omaavien yritysten edustajiin. Saatuja vastauksia käsiteltiin tiivistetysti raportissa ja vastaukset sisällytettiin kokonaisuudessaan Kymenlaakson Jäte Oy:n laajempaan raporttiin, joka ei ole julkinen. Puhelinhaastattelujen pohjalta nähtiin, että yrityksillä on kiinnostusta materiaalia kohtaan, mutta samalla vastauksiin vaikuttavat mädätysjäännöksen analyysitulokset. Poltto-ominaisuuksiin liittyvät analyysit tullaan toteuttamaan vuoden 2012 aikana. Laitoksilla oli myös vaihtelevia rajoituksia materiaalia kohtaan, mutta analyysituloksista riippuen materiaalia voidaan hyödyntää energiana tuhansia tai jopa kymmeniä tuhansia tonneja vuodessa alle 100 km etäisyydellä Kymenlaakson Jäte Oy:stä.

Current status of the waste-to-energy chain in the County of North Savo, Finland

The aim of this report is to describe the current status of the waste-to-energy chain in the province of Northern Savonia in Finland. This work is part of the Baltic Sea Region Programme project Remowe-Regional Mobilizing of Sustainable Waste-to-Energy Production (2009-2012). Partnering regions across Baltic Sea countries have parallelly investigated the current status, bottle-necks and needs for development in their regions. Information about the current status is crucial for the further work within the Remowe project, e.g. in investigating the possible future status in target regions. Ultimate result from the Northern Savonia point of view will be a regional model which utilizes all available information and facilitates decision-making concerning energy utilization of waste. The report contains information on among others: - waste management system (sources, amounts, infrastructure) - energy system (use, supply, infrastructure) - administrative structure and legislation - actors and stakeholders in the waste-to-energy field, including interest and development ideas The current status of the regions will be compared in a separate Remowe report, with the focus on finding best practices that could be transferred among the regions. In this report, the current status has been defined as 2006-2009. In 2009, the municipal waste amount per capita was 479 kg/inhabitant in Finland. Industrial waste amounted 3550 kg/inhabitant, respectively. The potential bioenergy from biodegradable waste amounts 1 MWh/inhabitant in Northern Savonia. This figure includes animal manure, crops that would be suitable for energy use, sludge from municipal sewage treatment plants and separately collected biowaste. A key strategy influencing also to Remowe work is the waste plan for Eastern Finland. Currently there operate two digestion plants in Northern Savonia: Lehtoniemi municipal sewage treatment sludge digestion plant of Kuopion Vesi and the farm-scale research biogas plant of Agrifood Research Finland in Maaninka. Moreover, landfill gas is collected to energy use from Heinälamminrinne waste management centre and Silmäsuo closed landfill site, both belonging to Jätekukko Oy. Currently there is no thermal utilization of waste in Northern Savonia region. However, Jätekukko Oy is pretreating mixed waste and delivering refuse derived fuel (RDF) to Southern Finland to combustion. There is a strong willingness among seven regional waste management companies in Eastern Finland to build a waste incineration plant to Riikinneva waste management centre near city of Varkaus. The plant would use circulating fluidized bed (CFB) boiler. This would been a clear boost in waste-to-energy utilization in Northern Savonia and in many surrounding regions.

Limestone Reactions in a Fluidized Bed Heat Exchanger of an Oxy-fuel Circulating Fluidized Bed Boiler

Oxy-fuel combustion in a circulating fluidized bed (CFB) boiler appears to be a promising option for capturing CO2 in power plants. Oxy-fuel combustion is based on burning of fuel in the mixture of oxygen and re-circulated flue gas instead of air. Limestone (CaCO3) is typically used for capturing of SO2 in CFB boilers where limestone calcines to calcium oxide (CaO). Because of high CO2 concentration in oxy-fuel combustion, calcination reaction may be hindered or carbonation, the reverse reaction of calcination, may occur. Carbonation of CaO particles can cause problems especially in the circulation loop of a CFB boiler where temperature level is lower than in the furnace. The aim of the thesis was to examine carbonation of CaO in a fluidized bed heat exchanger of a CFB boiler featuring oxy-fuel combustion. The calculations and analyzing were based on measurement data from an oxy-fuel pilot plant and on 0-dimensional (0D) gas balance of a fluidized bed heat exchanger. Additionally, the objective was to develop a 1-dimensional (1D) model of a fluidized bed heat exchanger by searching a suitable pre-exponential factor for a carbonation rate constant. On the basis of gas measurement data and the 0D gas balance, it was found that the amount of fluidization gas decreased as it flew through the fluidized bed heat exchanger. Most likely the reason for this was carbonation of CaO. It was discovered that temperature has a promoting effect on the reaction rate of carbonation. With the 1D model, a suitable pre-exponential factor for the equation of carbonation rate constant was found. However, during measurements there were several uncertainties, and in the calculations plenty of assumptions were made. Besides, the temperature level in the fluidized bed heat exchanger was relatively low during the measurements. Carbonation should be considered when fluidized bed heat exchangers and the capacity of related fans are designed for a CFB boiler with oxy-fuel combustion.

Design of an amplifier and an instrumentation setup for a harsh environment heat flux measurement application – case axial flux electric machine

Measurement is a tool for researching. Therefore, it is important that the measuring process is carried out correctly, without distorting the signal or the measured event. Researches of thermoelectric phenomena have been focused more on transverse thermoelectric phenomena during recent decades. Transverse Seebeck effect enables to produce thinner and faster heat flux sensor than before. Studies about transverse Seebeck effect have so far focused on materials, so in this Master’s Thesis instrumentation of transverse Seebeck effect based heat flux sensor is studied, This Master’s Thesis examines an equivalent circuit of transverse Seebeck effect heat flux sensors, their connectivity to electronics and choosing and design a right type amplifier. The research is carried out with a case study which is Gradient Heat Flux Sensors and an electrical motor. In this work, a general equivalent circuit was presented for the transverse Seebeck effect-based heat flux sensor. An amplifier was designed for the sensor of the case study, and the solution was produced for the measurement of the local heat flux of the electric motor to improve the electromagnetic compatibility.

The effects of welding heat input on the usability of high strength steels in welded structures

High strength steel (HSS) has been in use in workshops since the 1980s. At that time, the significance of the term HSS differed from the modern conception as the maximum yield strength of HSSs has increased nearly every year. There are three different ways to make HSS. The first and oldest method is QT (quenched and tempered) followed by the TMCP (thermomechanical controlled process) and DQ (direct quenching) methods. This thesis consists of two parts, the first of which part introduces the research topic and discusses welded HSS structures by characterizing the most important variables. In the second part of the thesis, the usability of welded HSS structures is examined through a set of laboratory tests. The results of this study explain the differences in the usability of the welded HSSs made by the three different methods. The results additionally indicate that usage of different HSSs in the welded structures presumes that manufacturers know what kind of HSS they are welding. As manufacturers use greater strength HSSs in welded structures, the demands for welding rise as well. Therefore, during the manufacturing process, factors such as heat input, cooling time, weld quality, and more must be under careful observation.