Salient Pole Synchronous Machine Modelling in an Industrial Direct Torque Controlled Drive Application

Synchronous motors are used mainly in large drives, for example in ship propulsion systems and in steel factories' rolling mills because of their high efficiency, high overload capacity and good performance in the field weakening range. This, however, requires an extremely good torque control system. A fast torque response and a torque accuracy are basic requirements for such a drive. For large power, high dynamic performance drives the commonly known principle of field oriented vector control has been used solely hitherto, but nowadays it is not the only way to implement such a drive. A new control method Direct Torque Control (DTC) has also emerged. The performance of such a high quality torque control as DTC in dynamically demanding industrial applications is mainly based on the accurate estimate of the various flux linkages' space vectors. Nowadays industrial motor control systems are real time applications with restricted calculation capacity. At the same time the control system requires a simple, fast calculable and reasonably accurate motor model. In this work a method to handle these problems in a Direct Torque Controlled (DTC) salient pole synchronous motor drive is proposed. A motor model which combines the induction law based "voltage model" and motor inductance parameters based "current model" is presented. The voltage model operates as a main model and is calculated at a very fast sampling rate (for example 40 kHz). The stator flux linkage calculated via integration from the stator voltages is corrected using the stator flux linkage computed from the current model. The current model acts as a supervisor that prevents only the motor stator flux linkage from drifting erroneous during longer time intervals. At very low speeds the role of the current model is emphasised but, nevertheless, the voltage model always stays the main model. At higher speeds the function of the current model correction is to act as a stabiliser of the control system. The current model contains a set of inductance parameters which must be known. The validation of the current model in steady state is not self evident. It depends on the accuracy of the saturated value of the inductances. Parameter measurement of the motor model where the supply inverter is used as a measurement signal generator is presented. This so called identification run can be performed prior to delivery or during drive commissioning. A derivation method for the inductance models used for the representation of the saturation effects is proposed. The performance of the electrically excited synchronous motor supplied with the DTC inverter is proven with experimental results. It is shown that it is possible to obtain a good static accuracy of the DTC's torque controller for an electrically excited synchronous motor. The dynamic response is fast and a new operation point is achieved without oscillation. The operation is stable throughout the speed range. The modelling of the magnetising inductance saturation is essential and cross saturation has to be considered as well. The effect of cross saturation is very significant. A DTC inverter can be used as a measuring equipment and the parameters needed for the motor model can be defined by the inverter itself. The main advantage is that the parameters defined are measured in similar magnetic operation conditions and no disagreement between the parameters will exist. The inductance models generated are adequate to meet the requirements of dynamically demanding drives.

Performance Evaluation and Calibration of Machine Vision Measurement

This thesis presents the calibration and comparison of two systems, a machine vision system that uses 3 channel RGB images and a line scanning spectral system. Calibration. is the process of checking and adjusting the accuracy of a measuring instrument by comparing it with standards. For the RGB system self-calibrating methods for finding various parameters of the imaging device were developed. Color calibration was done and the colors produced by the system were compared to the known colors values of the target. Software drivers for the Sony Robot were also developed and a mechanical part to connect a camera to the robot was also designed. For the line scanning spectral system, methods for the calibrating the alignment of the system and the measurement of the dimensions of the line scanned by the system were developed. Color calibration of the spectral system is also presented.

TransPromo communication as a part of company’s marketing communications when the e-bill is a medium

The goal of this thesis was to research what TransPromo is, why companies want to implement TransPromo communication, and what the elements of effective Transpromo communication are. Furthermore, the goal was to develop a TransPromo communication strategy and a normative model for TeliaSonera Finland, which depicts the elements of effective TransPromo communication when the electronic bill is a medium. Abductive reasoning was utilized in this thesis, which means that empirical and theoretical worlds are alternating in researcher’s reasoning process. This thesis didn’t rely on any specific theory nor did it utilize any previous theoretical model. However, certain theoretical connections existed so this thesis cannot be considered purely inductive. The empirical part of this thesis was conducted by examining secondary industry data and by conducting specialist interviews at TeliaSonera Finland and Strålfors. Grounded Theory approach was utilized in the analysis of the interview data and content analysis was used in the analysis of secondary industry data. This thesis increases knowledge in the area of TransPromo communication, and provides one definition of TransPromo communication. As a result of this thesis, a TransPromo communication strategy and a normative model for TeliaSonera Finland was built. The model depicts the elements of the effective TransPromo communication when the e-bill is a medium. The TranPromo communication objective is to utilize transaction documents, such as bills, in order to deliver targeted and personalized marketing messages to current customers. The aim is to strengthen the customer relationship, and to enforce up-sell and cross-sell opportunities and cost savings.

Machine Learning and Clinical Text. Supporting Health Information Flow

Fluent health information flow is critical for clinical decision-making. However, a considerable part of this information is free-form text and inabilities to utilize it create risks to patient safety and cost-­effective hospital administration. Methods for automated processing of clinical text are emerging. The aim in this doctoral dissertation is to study machine learning and clinical text in order to support health information flow.First, by analyzing the content of authentic patient records, the aim is to specify clinical needs in order to guide the development of machine learning applications.The contributions are a model of the ideal information flow,a model of the problems and challenges in reality, and a road map for the technology development. Second, by developing applications for practical cases,the aim is to concretize ways to support health information flow. Altogether five machine learning applications for three practical cases are described: The first two applications are binary classification and regression related to the practical case of topic labeling and relevance ranking.The third and fourth application are supervised and unsupervised multi-class classification for the practical case of topic segmentation and labeling.These four applications are tested with Finnish intensive care patient records.The fifth application is multi-label classification for the practical task of diagnosis coding. It is tested with English radiology reports.The performance of all these applications is promising. Third, the aim is to study how the quality of machine learning applications can be reliably evaluated.The associations between performance evaluation measures and methods are addressed,and a new hold-out method is introduced.This method contributes not only to processing time but also to the evaluation diversity and quality. The main conclusion is that developing machine learning applications for text requires interdisciplinary, international collaboration. Practical cases are very different, and hence the development must begin from genuine user needs and domain expertise. The technological expertise must cover linguistics,machine learning, and information systems. Finally, the methods must be evaluated both statistically and through authentic user-feedback.

Concentrated Winding Multiphase Permanent Magnet Machine Design and Electromagnetic Properties – Case Axial Flux Machine

Concentrated winding permanent magnet machines and their electromagnetic properties are studied in this doctoral thesis. The thesis includes a number of main tasks related to the application of permanent magnets in concentrated winding open slot machines. Suitable analytical methods are required for the first design calculations of a new machine. Concentrated winding machines differ from conventional integral slot winding machines in such a way that adapted analytical calculation methods are needed. A simple analytical model for calculating the concentrated winding axial flux machines is provided. The next three main design tasks are discussed in more detail in the thesis. The magnetic length of the rotor surface magnet machines is studied, and it is shown that the traditional methods have to be modified also in this respect. An important topic in this study has been to evaluate and minimize the rotor permanent magnet Joule losses by using segmented magnets in the calculations and experiments. Determination of the magnetizing and leakage inductances for a concentrated winding machine and the torque production capability of concentrated winding machines with different pole pair numbers are studied, and the results are compared with the corresponding properties of integral slot winding machines. The thesis introduces a new practical permanent magnet motor type for industrial use. The special features of the machine are based on the option of using concentrated winding open slot constructions of permanent magnet synchronous machines in the normal speed ranges of industrial motors, for instance up to 3000 min-1, without excessive rotor losses. By applying the analytical equations and methods introduced in the thesis, a 37 kW 2400 min-1 12-slot 10-pole axial flux machine with rotor-surfacemounted magnets is designed. The performance of the designed motor is determined by experimental measurements and finite element calculations.

Computational and Experimental Investigation of the Grooved Roll in Paper Machine Environment

In the paper machine, it is not a desired feature for the boundary layer flows in the fabric and the roll surfaces to travel into the closing nips, creating overpressure. In this thesis, the aerodynamic behavior of the grooved roll and smooth rolls is compared in order to understand the nip flow phenomena, which is the main reason why vacuum and grooved roll constructions are designed. A common method to remove the boundary layer flow from the closing nip is to use the vacuum roll construction. The downside of the use of vacuum rolls is high operational costs due to pressure losses in the vacuum roll shell. The deep grooved roll has the same goal, to create a pressure difference over the paper web and keep the paper attached to the roll or fabric surface in the drying pocket of the paper machine. A literature review revealed that the aerodynamic functionality of the grooved roll is not very well known. In this thesis, the aerodynamic functionality of the grooved roll in interaction with a permeable or impermeable wall is studied by varying the groove properties. Computational fluid dynamics simulations are utilized as the research tool. The simulations have been performed with commercial fluid dynamics software, ANSYS Fluent. Simulation results made with 3- and 2-dimensional fluid dynamics models are compared to laboratory scale measurements. The measurements have been made with a grooved roll simulator designed for the research. The variables in the comparison are the paper or fabric wrap angle, surface velocities, groove geometry and wall permeability. Present-day computational and modeling resources limit grooved roll fluid dynamics simulations in the paper machine scale. Based on the analysis of the aerodynamic functionality of the grooved roll, a grooved roll simulation tool is proposed. The smooth roll simulations show that the closing nip pressure does not depend on the length of boundary layer development. The surface velocity increase affects the pressure distribution in the closing and opening nips. The 3D grooved roll model reveals the aerodynamic functionality of the grooved roll. With the optimal groove size it is possible to avoid closing nip overpressure and keep the web attached to the fabric surface in the area of the wrap angle. The groove flow friction and minor losses play a different role when the wrap angle is changed. The proposed 2D grooved roll simulation tool is able to replicate the grooved aerodynamic behavior with reasonable accuracy. A small wrap angle predicts the pressure distribution correctly with the chosen approach for calculating the groove friction losses. With a large wrap angle, the groove friction loss shows too large pressure gradients, and the way of calculating the air flow friction losses in the groove has to be reconsidered. The aerodynamic functionality of the grooved roll is based on minor and viscous losses in the closing and opening nips as well as in the grooves. The proposed 2D grooved roll model is a simplification in order to reduce computational and modeling efforts. The simulation tool makes it possible to simulate complex paper machine constructions in the paper machine scale. In order to use the grooved roll as a replacement for the vacuum roll, the grooved roll properties have to be considered on the basis of the web handling application.

Improving Cross Direction Basis Weight Profile in a Fourdrinier Paper Machine

The purpose of this study was to improve PM7’s basis weight CD profile in Stora Enso’s Berghuizer mill and to search mechanical defects which affect to the formation of the basis weight CD profile. In the theoretical part PM7’s structure was presented and the formation of the basis weight and caliper CD profiles was examined as well as disturbances which are affecting to the formation. The function of the control system was scrutinised for the side of CD profiles as well as the formation of the measured CD profiles. Tuning of the control system was examined through the response model and filtering. Specification of the response model and filtering was explained and how to determine 2sigma statistical number. In the end of the theoretical part ATPA hardware and a new profile browser were introduced. In the experimental part focus was in the beginning to search and remove mechanical defects which are affecting to CD profiles. The next step was to verify the reliability of the online measurements, to study the stability of the basis weight CD profile and to find out so called fingerprint, a basis weight CD profile which is unique for each paper machine. New response model and filtering value for basis weight CD profile was determined by bump tests. After a follow up period the affect of the new response model and filtering was analysed.

Visualization of communication system testing logs

During the past decades testing has matured from ad-hoc activity into being an integral part of the development process. The benefits of testing are obvious for modern communication systems, which operate in heterogeneous environments amongst devices from various manufacturers. The increased demand for testing also creates demand for tools and technologies that support and automate testing activities. This thesis discusses applicability of visualization techniques in the result analysis part of the testing process. Particularly, the primary focus of this work is visualization of test execution logs produced by a TTCN-3 test system. TTCN-3 is an internationally standardized test specification and implementation language. The TTCN-3 standard suite includes specification of a test logging interface and a graphical presentation format, but no immediate relationship between them. This thesis presents a technique for mapping the log events to the graphical presentation format along with a concrete implementation, which is integrated with the Eclipse Platform and the OpenTTCN Tester toolchain. Results of this work indicate that for majority of the log events, a visual representation may be derived from the TTCN-3 standard suite. The remaining events were analysed and three categories relevant in either log analysis or implementation of the visualization tool were identified: events indicating insertion of something into the incoming queue of a port, events indicating a mismatch and events describing the control flow during the execution. Applicability of the results is limited into the domain of TTCN-3, but the developed mapping and the implementation may be utilized with any TTCN-3 tool that is able to produce the execution log in the standardized XML format.

Utilizing Near Field Communication in Health Care

In this master’s thesis, possibilities to utilize Near Field Communication (NFC) technology in health care applications are examined. NFC is a short-range wireless communication technology that enables the exchange of data between devices. Main components in NFC are tag, which contains data, a NFC reader device, which can be for instance embedded to mobile phone and also act as a tag, and an antennae in both tag and reader. In this work NFC technology is discussed and its utilization in health care information systems that are in use or in trial. Utilization of information technology in health care field is examined superficially. In this thesis, a system utilizing NFC is designed and its requirements and architecture presented. NFC is used in identification of care worker. When care worker arrives at the house of a patient, she brings the NFC-enabled mobile phone near NFC tag. This sends information to the application server. This information contains the time of arrival and patient and location identifier. When care worker leaves the place, she repeats the procedure. Information gathered can be used in reporting and real time tracking.

Simulating the performance of paper machine control

The topic of this thesis is the simulation of a combination of several control and data assimilation methods, meant to be used for controlling the quality of paper in a paper machine. Paper making is a very complex process and the information obtained from the web is sparse. A paper web scanner can only measure a zig zag path on the web. An assimilation method is needed to process estimates for Machine Direction (MD) and Cross Direction (CD) profiles of the web. Quality control is based on these measurements. There is an increasing need for intelligent methods to assist in data assimilation. The target of this thesis is to study how such intelligent assimilation methods are affecting paper web quality. This work is based on a paper web simulator, which has been developed in the TEKES funded MASI NoTes project. The simulator is a valuable tool in comparing different assimilation methods. The thesis contains the comparison of four different assimilation methods. These data assimilation methods are a first order Bayesian model estimator, an ARMA model based on a higher order Bayesian estimator, a Fourier transform based Kalman filter estimator and a simple block estimator. The last one can be considered to be close to current operational methods. From these methods Bayesian, ARMA and Kalman all seem to have advantages over the commercial one. The Kalman and ARMA estimators seems to be best in overall performance.

The relationship between a virtual leader’s communication practices and a virtual team’s performance

A lot of research has been carried out into virtual teams and virtual leadership, yet there is hardly any research available on the communication behaviour of virtual leaders within a real business context. This research assessed the communication practices of virtual leaders and analysed the relationship between these practices and the performance of virtual teams. The objective of this research was to examine the distinctions of virtual teams, to study the leader’s role in a virtual team and its performance, and to examine the leader’s communication practices within virtual teams. The research involves a case study in which interviews have been carried out within an international technology company headquartered in Finland. Qualitative research methods were applied in the research. Based on the results of the study it can be said that there is a strong relationship between a virtual leader’s communication practices and a virtual team member’s job satisfaction. Through their communication practices, activities and message contents, leaders can affect the job satisfaction of virtual team members. In virtual leadership the focus is not in virtual but in leadership. It does not matter if the context is virtual or face-to-face; similar communication practices are good in both cases. As the global economic crisis strongly affected the sales results of the between a leader’s communication practices and a virtual team’s objective performance cannot be made.

Permanent Magnet Synchronous Machine for Parallel Hybrid Vehicle

The aim of this thesis is to describe hybrid drive design problems, the advantages and difficulties related to the drive. A review of possible hybrid constructions, benefits of parallel, series and series-parallel hybrids is done. In the thesis analytical and finite element calculations of permanent magnet synchronous machines with embedded magnets were done. The finite element calculations were done using Cedrat’s Flux 2D software. This machine is planned to be used as a motor-generator in a low power parallel hybrid vehicle. The boundary conditions for the design were found from Lucas-TVS Ltd., India. Design Requirements, briefly: • The system DC voltage level is 120 V, which implies Uphase = 49 V (RMS) in a three phase system. • The power output of 10 kW at base speed 1500 rpm (Torque of 65 Nm) is desired. • The maximum outer diameter should not be more than 250 mm, and the maximum core length should not exceed 40 mm. The main difficulties which the author met were the dimensional restrictions. After having designed and analyzed several possible constructions they were compared and the final design selected. Dimensioned and detailed design is performed. Effects of different parameters, such as the number of poles, number of turns and magnetic geometry are discussed. The best modification offers considerable reduction of volume.

A Communication Middleware Quality Enhancement with Qt Framework

In this thesis, a Peer-to-Peer communication middleware for mobile environment is developed using the Qt framework and the Qt Mobility extension. The Peer-to-Peer middleware – called as PeerHood – is for service sharing in network neighborhood. In addition, the PeerHood enables service connectivity and device monitoring functionalities. The concept of the PeerHood is already available in native C++ implementation on Linux platform using services from the platform. In this work, the PeerHood concept is remade to be based on use of the Qt framework. The objective of the new solution is to increase PeerHood quality with using functionalities from the Qt framework and the Qt Mobility extension. Furthermore, by using the Qt framework, the PeerHood middleware can be implemented to be portable cross-platform middleware. The quality of the new PeerHood implementation is evaluated with defined quality factors and compared with the existing PeerHood. Reliability, CPU usage, memory usage and static code analysis metrics are used in evaluation. The new PeerHood is shown to be more reliable and flexible that the existing one.

Carbon footprint as part of a company’s external environmental communication

The aim of this thesis was to find out how the carbon footprint calculations can be utilized in the company’s external environmental communication, what is the demand for carbon footprint from the market, and how the other actors in the forest industry have approached the issue. The aim was to recognize the best practises to communicate carbon footprints and to find possibilities to extend the UPM-Kymmene Wood Oy’s mill specific carbon footprints. This research included a literature review, an inquiry to the UPM-Kymmene Wood Oy’s sales offices, and Internet survey concerning the external environmental communication in the forest industry and three small case studies based on mill specific parameters. The inquiry to the sales offices showed that the carbon footprint is not yet a common demand from the customers in the wood product sector. In addition, the Internet survey showed that generally in the forest industry, not much has been done concerning carbon footprint communication so far. The biggest challenge in carbon footprint communication is the variation in the knowledge level of the receivers. In addition btob and btoc communication situations demand a different approach to the issue. Carbon profile brochures developed in the company can be seen as suitable for btob communication situations. Case studies have shown that the contribution of final product transport to the overall carbon footprint was significant. It was recommended to include post mill transport in the carbon footprint information supplied to the btob customers. When discussing environmental communication on a general level it can be stated that a good external environmental communication is based on facts, is open and proactive and takes into account the needs of the receiver. However, the openness and the quality of external environmental communication are essentially strategic decisions. The significance of internal communication as well as the knowhow in the communication and marketing networks play a major role in achieving success in external environmental communication. Carbon footprints are only one part of good balanced external environmental communication. One specific environmental feature like carbon footprint should not be over emphasized to the detriment of other important environmental aspects.