VVER-440 Thermal Hydraulics as a Computer Code Validation Challenge

This thesis concentrates on the validation of a generic thermal hydraulic computer code TRACE under the challenges of the VVER-440 reactor type. The code capability to model the VVER-440 geometry and thermal hydraulic phenomena specific to this reactor design has been examined and demonstrated acceptable. The main challenge in VVER-440 thermal hydraulics appeared in the modelling of the horizontal steam generator. The major challenge here is not in the code physics or numerics but in the formulation of a representative nodalization structure. Another VVER-440 specialty, the hot leg loop seals, challenges the system codes functionally in general, but proved readily representable. Computer code models have to be validated against experiments to achieve confidence in code models. When new computer code is to be used for nuclear power plant safety analysis, it must first be validated against a large variety of different experiments. The validation process has to cover both the code itself and the code input. Uncertainties of different nature are identified in the different phases of the validation procedure and can even be quantified. This thesis presents a novel approach to the input model validation and uncertainty evaluation in the different stages of the computer code validation procedure. This thesis also demonstrates that in the safety analysis, there are inevitably significant uncertainties that are not statistically quantifiable; they need to be and can be addressed by other, less simplistic means, ultimately relying on the competence of the analysts and the capability of the community to support the experimental verification of analytical assumptions. This method completes essentially the commonly used uncertainty assessment methods, which are usually conducted using only statistical methods.

From statin efficacy to everyday effectiveness: Studying the gap in between.

Statins are indicated for preventing cardiovascular disease events. Patients with diabetes have a risk of major cardiovascular events double the risk of their peers without diabetes. Thus, clinical treatment guidelines recommend statins for the management of diabetic dyslipidemia. The evidence base for statin use in cardiovascular disease derives from the randomized controlled statin trials designed to prove statin efficacy under ideal conditions, among a homogenous study population meeting strict trial eligibility criteria. This thesis was implemented as four pharmacoepidemiological statin studies using register data on realworld statin users. The overall purpose was to evaluate the trends, patterns and effectiveness of statin use in everyday life. More specifically, nationwide secular trends in statin use in Finland were analysed, especially among patient groups which had been underrepresented in the statin trials. Furthermore, the benchmarking statin trials in diabetes, the Heart Protection Study and the Collaborative Atorvastatin Diabetes Study, were evaluated for their representativeness for real-world diabetes care with the emphasis placed on adherence to statin use. The association between good adherence and the incidence of major cardiovascular events in the real-world was further investigated in diabetes. These studies demonstrate that statin initiations increased from 1995 to 2005 in Finland. The increase was most pronounced among those aged at least 75 years and was observed already before the publication of rigorous trial data conducted in elderly subjects. Thus, statins seem to have been initiated in clinical practice also going beyond the strict trial eligibility criteria. Nonetheless, low adherence to statin use among the real-world patients with diabetes was found not only to limit the representativeness of the trials for clinical care but also to attenuate in all likelihood their benefits in the real-world. In fact, good adherence to statin use was found to associate with a decreased risk for major cardiovascular events in patients with diabetes. In conclusion, these studies highlight the importance of good adherence to statin use in clinical practice in order to obtain the full therapeutic value demonstrated in the statin trials. Simply increasing the number of statin users will not alone suffice in sharing our common resources appropriately.

Modelling the super-equilibria in thermal biomass conversion : applications and limitations of the constrained free energy method

Bioenergi ses som en viktig del av det nu- och framtida sortimentet av inhemsk energi. Svartlut, bark och skogsavfall täcker mer än en femtedel av den inhemska energianvändningen. Produktionsanläggningar kan fungera ofullständigt och en mängd gas-, partikelutsläpp och tjära produceras samtidigt och kan leda till beläggningsbildning och korrosion. Orsaken till dessa problem är ofta obalans i processen: vissa föreningar anrikas i processen och superjämviktstillstånd är bildas. I denna doktorsavhandling presenteras en ny beräkningsmetod, med vilken man kan beskriva superjämviktstillståndet, de viktigaste kemiska reaktionerna, processens värmeproduktion och tillståndsstorheter samtidigt. Beräkningsmetoden grundar sig på en unik frienergimetod med bivillkor som har utvecklats vid VTT. Den här så kallade CFE-metoden har tidigare utnyttjats i pappers-, metall- och kemiindustrin. Applikationer för bioenergi, vilka är demonstrerade i doktorsavhandlingen, är ett nytt användingsområde för metoden. Studien visade att beräkningsmetoden är väl lämpad för högtemperaturenergiprocesser. Superjämviktstillstånden kan uppstå i dessa processer och det kemiska systemet kan definieras med några bivillkor. Typiska tillämpningar är förbränning av biomassa och svartlut, förgasning av biomassa och uppkomsten av kväveoxider. Också olika sätt att definiera superjämviktstillstånd presenterades i doktorsavhandlingen: empiriska konstanter, empiriska hastighetsuttryck eller reaktionsmekanismer kan användas. Resultaten av doktorsavhandlingen kan utnyttjas i framtiden i processplaneringen och i undersökning av nya tekniska lösningar för förgasning, förbränningsteknik och biobränslen. Den presenterade metoden är ett bra alternativ till de traditionella mekanistiska och fenomenmodeller och kombinerar de bästa delarna av både. --------------------------------------------------------------- Bioenergia on tärkeä osa nykyistä ja tulevaa kotimaista energiapalettia. Mustalipeä, kuori ja metsätähteet kattavat yli viidenneksen kotimaisesta energian kulutuksesta. Tuotantolaitokset eivät kuitenkaan aina toimi täydellisesti ja niiden prosesseissa syntyy erilaisia kaasu- ja hiukkaspäästöjä, tervoja sekä prosessilaitteita kuluttavia saostumia ja ruostumista. Usein syy näihin ongelmiin on prosessissa esiintyvä epätasapainotila: tietyt yhdisteet rikastuvat prosessissa ja muodostavat supertasapainotiloja. Väitöstyössä kehitettiin uusi laskentamenetelmä, jolla voidaan kuvata nämä supertasapainotilat, tärkeimmät niihin liittyvät kemialliset reaktiot, prosessin lämmöntuotanto ja tilansuureet yhtä aikaa. Laskentamenetelmä perustuu VTT:llä kehitettyyn ainutlaatuiseen rajoitettuun vapaaenergiamenetelmään. Tätä niin kutsuttua CFE-menetelmää on aiemmin sovelluttu onnistuneesti muun muassa paperi-, metalli- ja kemianteollisuudessa. Väitöstyössä esitetyt bioenergiasovellukset ovat uusi sovellusalue menetelmälle. Työ osoitti laskentatavan soveltuvan hyvin korkealämpöisiin energiatekniikan prosesseihin, joissa kemiallista systeemiä rajoittavia tekijöitä oli rajallinen määrä ja siten super-tasapainotila saattoi muodostua prosessin aikana. Tyypillisiä sovelluskohteita ovat biomassan ja mustalipeän poltto, biomassan kaasutus ja typpioksidipäästöt. Työn aikana arvioitiin myös erilaisia tapoja määritellä super-tasapainojen muodostumista rajoittavat tekijät. Rajoitukset voitiin tehdä teollisiin mittauksiin pohjautuen, kokeellisia malleja hyödyntäen tai mekanistiseen reaktiokinetiikkaan perustuen. Tulevaisuudessa väitöstyön tuloksia voidaan hyödyntää prosessisuunnittelussa ja tutkittaessa uusia teknisiä ratkaisuja kaasutus- ja polttotekniikoissa sekä biopolttoaineiden tutkimuksessa. Kehitetty menetelmä tarjoaa hyvän vaihtoehdon perinteisille mekanistisille ja ilmiömalleille yhdistäen näiden parhaita puolia.

Measuring Effectiveness of Marketing Message: The Role of Verbal, Visual and Brand Elements

The aim of this paper is to study the role of verbal, visual and brand elements while meas-uring effectiveness of marketing message. The thesis is written in the context of mobile gaming industry. The object of the study is marketing message. To achieve the aim, the main research question was formulated: How do the elements of marketing message, such as verbal, visual and brand, affect the consumer’s attitude toward the ad, emotional response and attention capture? The theory development chapter lays on three corner stones – analysis of previous litera-ture on marketing message and its elements, namely verbal, visual and brand; overview of literature on attitude formation and particularly attitude toward the ad. In addition, investiga-tion of key points of emotional response and attention capture literature finalizes the chap-ter. The empirical part consists of experiment, conducted with 27 participants. Experiment includes the self-report semantically anchored scale, measuring the attitude toward the ad, as well as autonomic measures – eye tracking (attention capture) and facial expressions (emotional response). The results of the experiment showed that the size of the brand element – the logo – has an effect on the attention capture and the overall attitude toward the ad. The bigger the logo, the more time people spend viewing it, and they realise the message is more educa-tional and factual. The measure related to the visual element – the visual complexity – in-creases the intensity of participant’s facial expression. While the measure of verbal ele-ment – the contrast between text and background colours – leads to a better attitude to-ward the ad. The higher the contrast between text and background, the more known the message appears to the viewer.

Permanent magnet synchronous generator design solution for large directdrive wind turbines: Thermal behavior of the LC DD-PMSG

Wind is one of the most compelling forms of indirect solar energy. Available now, the conversion of wind power into electricity is and will continue to be an important element of energy self-sufficiency planning. This paper is one in a series intended to report on the development of a new type of generator for wind energy; a compact, high-power, direct-drive permanent magnet synchronous generator (DD-PMSG) that uses direct liquid cooling (LC) of the stator windings to manage Joule heating losses. The main param-eters of the subject LC DD-PMSG are 8 MW, 3.3 kV, and 11 Hz. The stator winding is cooled directly by deionized water, which flows through the continuous hollow conductor of each stator tooth-coil winding. The design of the machine is to a large degree subordinate to the use of these solid-copper tooth-coils. Both steady-state and timedependent temperature distributions for LC DD-PMSG were examined with calculations based on a lumpedparameter thermal model, which makes it possible to account for uneven heat loss distribution in the stator conductors and the conductor cooling system. Transient calculations reveal the copper winding temperature distribution for an example duty cycle during variable-speed wind turbine operation. The cooling performance of the liquid cooled tooth-coil design was predicted via finite element analysis. An instrumented cooling loop featuring a pair of LC tooth-coils embedded in a lamination stack was built and laboratory tested to verify the analytical model. Predicted and measured results were in agreement, confirming the predicted satisfactory operation of the LC DD-PMSG cooling technology approach as a whole.

Evaluation of novel programs in health counseling – their effectiveness in the oral health of young children, and their acceptance by parents and professionals in public dental service.

Aim and design: To evaluate family-based health counseling for young children, and to study the significance of adding parental self-care or the training of professionals to the programs. The effectiveness and acceptability of the programs were evaluated by comparing two new programs with an earlier one. Subjects and methods: The study was carried out in Vantaa, which was divided into three study areas. The subjects consisted of children born in 2008, particularly fi rstborn children, while children born in 2006 formed the historical control. The fi rst of the new programs emphasized oral hygiene and use of fl uoride, and the second program focused on proper diet and use of xylitol. The main outcome measure was mutansstreptococci (MS) in the dental biofi lm of two-year-olds, and the opinions of parents and dental professionals were evaluated using questionnaires. Results: The programs found wide acceptance among dental professionals. There were no group-related differences found in the MS scores of the two-year-olds. However, all groups combined, father’s advanced level of education and child’s proper use of xylitol were associated with negative MS scores. In the opinion of parents, the oral healthcare guidance at least somewhat met their expectations. Conclusions: The present fi ndings suggest that providing training and support for professionals in health education is important. The addition of parental self-care to supplement programs aimed at young children does not improve the program, although it may improve parental readiness to change their own health habits. Counseling for families might be best carried out through a routine patient-centered program.

Critical success factors for improving societal effectiveness of transport sector's R&D

This study investigates societal effectiveness of transport sector’s Research & Development (R&D) operations. In this study effectiveness refers to organization’s capability to produce the intended and desired impacts through its operations. The aim of this study is to identify the motives for evaluating societal effectiveness and recognize the critical success factors for improving effectiveness. The theoretical framework focuses first in the policy context of effectiveness evaluation in public sector and secondly the framework introduces the concept and process of effectiveness evaluation. The empirical part is carried out as a case study, which investigates societal effectiveness of Finnish Transport Agency’s (FTA’s) R&D. The aim is to recognize FTA’s critical success factors for improving R&D operations’ societal effectiveness. Based on these factors, the organization is able to define indicators for measuring effectiveness in the future operations. In this study societal effectiveness is investigated from R&D purchasers’ and R&D end- users’ points of views according to Purchaser-Provider-model. The results indicate that societal effectiveness evaluation is important part of R&D operations, but the implementation of the evaluation as part of daily operations is challenging. Because of limited resources, the organization is forced to strong priorization and therefore R&D tasks are secondary after the operational tasks. Based on the results the critical success factors can be recognized as resources and priorization, clear strategy and objectives, internal communications, cooperation between public and private sector and R&D implementation and dissemination.

Thermal modelling of commercial lithium-ion batteries

The accelerating adoption of electrical technologies in vehicles over the recent years has led to an increase in the research on electrochemical energy storage systems, which are among the key elements in these technologies. The application of electrochemical energy storage systems for instance in hybrid electrical vehicles (HEVs) or hybrid mobile working machines allows tolerating high power peaks, leading to an opportunity to downsize the internal combustion engine and reduce fuel consumption, and therefore, CO2 and other emissions. Further, the application of electrochemical energy storage systems provides an option of kinetic and potential energy recuperation. Presently, the lithium-ion (Li-ion) battery is considered the most suitable electrochemical energy storage type in HEVs and hybrid mobile working machines. However, the intensive operating cycle produces high heat losses in the Li-ion battery, which increase its operating temperature. The Li-ion battery operation at high temperatures accelerates the ageing of the battery, and in the worst case, may lead to a thermal runaway and fire. Therefore, an appropriate Li-ion battery cooling system should be provided for the temperature control in applications such as HEVs and mobile working machines. In this doctoral dissertation, methods are presented to set up a thermal model of a single Li-ion cell and a more complex battery module, which can be used if full information about the battery chemistry is not available. In addition, a non-destructive method is developed for the cell thermal characterization, which allows to measure the thermal parameters at different states of charge and in different points of cell surface. The proposed models and the cell thermal characterization method have been verified by experimental measurements. The minimization of high thermal non-uniformity, which was detected in the pouch cell during its operation with a high C-rate current, was analysed by applying a simplified pouch cell 3D thermal model. In the analysis, heat pipes were incorporated into the pouch cell cooling system, and an optimization algorithm was generated for the estimation of the optimalplacement of heat pipes in the pouch cell cooling system. An analysis of the application of heat pipes to the pouch cell cooling system shows that heat pipes significantly decrease the temperature non-uniformity on the cell surface, and therefore, heat pipes were recommended for the enhancement of the pouch cell cooling system.

Development of laboratory exercises for basic nuclear thermal hydraulics measurements

The thesis focuses on light water reactors (pressurized water reactors, boiling water reactors) and measurement techniques for basic thermal hydraulics parameters that are used in a nuclear power plant. The goal of this work is a development of laboratory exercises for basic nuclear thermal hydraulics measurements.

Determination of the thermal parameters of high-power batteries by local heat

A new approach to the determination of the thermal parameters of high-power batteries is introduced here. Application of local heat flux measurement with a gradient heat flux sensor (GHFS) allows determination of the cell thermal parameters in di_erent surface points of the cell. The suggested methodology is not cell destructive as it does not require deep discharge of the cell or application of any charge/discharge cycles during measurements of the thermal parameters of the cell. The complete procedure is demonstrated on a high-power Li-ion pouch cell, and it is verified on a sample with well-known thermal parameters. A comparison of the experimental results with conventional thermal characterization methods shows an acceptably low error. The dependence of the cell thermal parameters on state of charge (SoC) and measurement points on the surface was studied by the proposed measurement approach.

Visualization of thermal-hydraulic nodes

The purpose of this thesis was to develop a program that can illustrate thermal-hydraulic node dimensions used in SMABRE simulations. These created node illustrations are used to verify the correctness of the designed simulation model and in addition they can be included in scientific reports. This thesis will include theory about SMABRE and relevant programs that were used to achieve the ending results. This thesis will give explanations for different modules that were created and used in the finished program, and it will present the different problems encountered and provide the solutions. The most important objective in this thesis is to display the results of generic VVER-1000 node dimensions and verify the correctness in the displayed part. The finished program was created using code language Python.