Magnetic and transport properties of InGaAs quantum wells with Mn

In the present work structural, magnetic and transport properties of InGaAs quantum wells (QW) prepared by MBE with an remote Mn layer are investigated. By means of high-resolution X-ray diffractometry the structure of the samples is analyzed. It is shown that Mn ions penetrate into the QW. Influence of the thickness of GaAs spacer and annealing at 286 ºС on the properties of the system is shown. It is shown that annealing of the samples led to Mn activation and narrowing of the Mn layer. Substantial role of 2D holes in ferromagnetic ordering in Mn layer is shown. Evidence for that is observation of maximum at 25 – 55 K on the resistivity temperature dependence. Position of maximum, which is used for quantitative assessment of the Curie temperature, correlates with calculations of the Curie temperature for structures with indirect interaction via 2D holes’ channel. Dependence of the Curie temperature on the spacer thickness shows, that creation of applicable spintronic devices needs high-precision equipment to manufacture extra fine structures. The magnetotransport measurements show that charge carrier mobility is very low. This leads to deficiency of the anomalous Hall effect. At the same time, magnetic field dependences of the magnetization at different temperatures demonstrate that systems are ferromagnetically ordered. These facts, most probably, give evidence of presence of the ferromagnetic MnAs clusters.

Magnetic and transport properties of II-V diluted magnetic semiconductors doped with manganese and nickel

This thesis is devoted to investigations of three typical representatives of the II-V diluted magnetic semiconductors, Zn1-xMnxAs2, (Zn1-xMnx)3As2 and p-CdSb:Ni. When this work started the family of the II-V semiconductors was presented by only the compounds belonging to the subgroup II3-V2, as (Zn1-xMnx)3As2, whereas the rest of the materials mentioned above were not investigated at all. Pronounced low-field magnetic irreversibility, accompanied with a ferromagnetic transition, are observed in Zn1-xMnxAs2 and (Zn1-xMnx)3As2 near 300 K. These features give evidence for presence of MnAs nanosize magnetic clusters, responsible for frustrated ground magnetic state. In addition, (Zn1-xMnx)3As2 demonstrates large paramagnetic response due to considerable amount of single Mn ions and small antiferromagnetic clusters. Similar paramagnetic system existing in Zn1-xMnxAs2 is much weaker. Distinct low-field magnetic irreversibility, accompanied with a rapid saturation of the magnetization with increasing magnetic field, is observed near the room temperature in p- CdSb:Ni, as well. Such behavior is connected to the frustrated magnetic state, determined by Ni-rich magnetic Ni1-xSbx nanoclusters. Their large non-sphericity and preferable orientations are responsible for strong anisotropy of the coercivity and saturation magnetization of p- CdSb:Ni. Parameters of the Ni1-xSbx nanoclusters are estimated. Low-temperature resistivity of p-CdSb:Ni is governed by a hopping mechanism of charge transfer. The variable-range hopping conductivity, observed in zero magnetic field, demonstrates a tendency of transformation into the nearest-neighbor hopping conductivity in non-zero magnetic filed. The Hall effect in p-CdSb:Ni exhibits presence of a positive normal and a negative anomalous contributions to the Hall resistivity. The normal Hall coefficient is governed mainly by holes activated into the valence band, whereas the anomalous Hall effect, attributable to the Ni1-xSbx nanoclusters with ferromagnetically ordered internal spins, exhibits a low-temperature power-law resistivity scaling.

Strategic practices : : hidden histories of gender in Finland 1880-2005 : projektikuvaus

Ajankohtaista

Improving demand forecasting practices in the industrial context

Demand forecasting is one of the fundamental managerial tasks. Most companies do not know their future demands, so they have to make plans based on demand forecasts. The literature offers many methods and approaches for producing forecasts. When selecting the forecasting approach, companies need to estimate the benefits provided by particular methods, as well as the resources that applying the methods call for. Former literature points out that even though many forecasting methods are available, selecting a suitable approach and implementing and managing it is a complex cross-functional matter. However, research that focuses on the managerial side of forecasting is relatively rare. This thesis explores the managerial problems that are involved when demand forecasting methods are applied in a context where a company produces products for other manufacturing companies. Industrial companies have some characteristics that differ from consumer companies, e.g. typically a lower number of customers and closer relationships with customers than in consumer companies. The research questions of this thesis are: 1. What kind of challenges are there in organizing an adequate forecasting process in the industrial context? 2. What kind of tools of analysis can be utilized to support the improvement of the forecasting process? The main methodological approach in this study is design science, where the main objective is to develop tentative solutions to real-life problems. The research data has been collected from two organizations. Managerial problems in organizing demand forecasting can be found in four interlinked areas: 1. defining the operational environment for forecasting, 2. defining the forecasting methods, 3. defining the organizational responsibilities, and 4. defining the forecasting performance measurement process. In all these areas, examples of managerial problems are described, and approaches for mitigating these problems are outlined.

Stress testing practices in risk management - Empirical evidence from the Finnish banking and insurance sectors

The main purpose of this study was to analyze how stress tests are used in risk management in the Finnish banking and insurance sectors. In order to enhance understanding of the topic, stress testing was explored in the context of corporate governance and regulato-ry implications of Basel II and Solvency II on stress testing were examined. In addition, the effects of the global financial crisis on stress testing were mapped and the differences in stress testing practices between the banking and insurance sector were discussed. The research method was qualitative case study and it was conducted by interviewing risk managers from ten institutions and a representative from FIN-FSA. Findings pointed out that stress testing practices vary significantly between different institutions. Interesting observations were made in terms of stress testing practices in the banking and insurance sectors. The increasing importance and use of stress tests were recognized as a result of the financial crisis. Stress testing was even considered more like art than science given the amount of challenges it involves. In general, improvements in stress tests were suggested, with an emphasis on stress concentration between different types of risks.

Design of Installation for Transport Measurements

In the present work the aim was to prepare an automatic installation for studies of galvanomagnetic effects in solids and to test it by calibration measurements. As a result required automatic installation was created in this work and test measurements were performed. Created setup automatically provides measurements of the magnetoresistance of the Hall effect with an accuracy of ± 2 µV in the temperature range 2 – 300 K and steady magnetic fields up to 6 T. The test measurements of the glassy carbon samples showed that the setup is reliable, has high sensitivity and is easy to use. The results obtained in the research process are pioneer and will be separately analyzed.

A generalized 1D particle transport method for convection diffusion reaction model

This work is devoted to the development of numerical method to deal with convection diffusion dominated problem with reaction term, non - stiff chemical reaction and stiff chemical reaction. The technique is based on the unifying Eulerian - Lagrangian schemes (particle transport method) under the framework of operator splitting method. In the computational domain, the particle set is assigned to solve the convection reaction subproblem along the characteristic curves created by convective velocity. At each time step, convection, diffusion and reaction terms are solved separately by assuming that, each phenomenon occurs separately in a sequential fashion. Moreover, adaptivities and projection techniques are used to add particles in the regions of high gradients (steep fronts) and discontinuities and transfer a solution from particle set onto grid point respectively. The numerical results show that, the particle transport method has improved the solutions of CDR problems. Nevertheless, the method is time consumer when compared with other classical technique e.g., method of lines. Apart from this advantage, the particle transport method can be used to simulate problems that involve movingsteep/smooth fronts such as separation of two or more elements in the system.

Solution marketing characteristics and practices

The first objective of this master's thesis is to find out how the concepts solution and solution marketing are defined in the literature. In order to do so, solution marketing literature is reviewed widely. Another target is to identify the characteristics of solution marketing and to explain how solution marketing can be carried out. The final objective is to determine how well the described solution marketing practices are executed in the target company, and this will be studied with a survey. A solution can be described as a co-created and customized combination of products and services. Solution marketing aims at developing and anticipating customer's business needs and it involves close collaboration between customer and supplier. Solution marketing communication is targeted to a specific audience. It entails deep customer intimacy and is focused on understanding customer's business problem. Solution marketing also requires close collaboration between sales and marketing as well as customer focused mindset. Solution marketing can be executed by promoting thought leadership, presenting solution offering, creating close customer relationships and treating customers as individuals. Solution provider's whole organization must engage customer focus.

The relationship between a virtual leader’s communication practices and a virtual team’s performance

A lot of research has been carried out into virtual teams and virtual leadership, yet there is hardly any research available on the communication behaviour of virtual leaders within a real business context. This research assessed the communication practices of virtual leaders and analysed the relationship between these practices and the performance of virtual teams. The objective of this research was to examine the distinctions of virtual teams, to study the leader’s role in a virtual team and its performance, and to examine the leader’s communication practices within virtual teams. The research involves a case study in which interviews have been carried out within an international technology company headquartered in Finland. Qualitative research methods were applied in the research. Based on the results of the study it can be said that there is a strong relationship between a virtual leader’s communication practices and a virtual team member’s job satisfaction. Through their communication practices, activities and message contents, leaders can affect the job satisfaction of virtual team members. In virtual leadership the focus is not in virtual but in leadership. It does not matter if the context is virtual or face-to-face; similar communication practices are good in both cases. As the global economic crisis strongly affected the sales results of the between a leader’s communication practices and a virtual team’s objective performance cannot be made.

Magnetic and transport properties of LaMnO3+δ, La1-xCaxMnO3, La1-xCaxMn1-yFeyO3 and La1-xSrxMn1-yFeyO3

Interest to hole-doped mixed-valence manganite perovskites is connected to the ‘colossal’ magnetoresistance. This effect or huge drop of the resistivity, ρ, in external magnetic field, B, attains usually the maximum value near the ferromagnetic Curie temperature, TC. In this thesis are investigated conductivity mechanisms and magnetic properties of the manganite perovskite compounds LaMnO3+, La1-xCaxMnO3, La1-xCaxMn1-yFeyO3 and La1- xSrxMn1-yFeyO3. When the present work was started the key role of the phase separation and its influence on the properties of the colossal magnetoresistive materials were not clear. Our main results are based on temperature dependencies of the magnetoresistance and magnetothermopower, investigated in the temperature interval of 4.2 - 300 K in magnetic fields up to 10 T. The magnetization was studied in the same temperature range in weak (up to 0.1 T) magnetic fields. LaMnO3+δ is the parent compound for preparation of the hole-doped CMR materials. The dependences of such parameters as the Curie temperature, TC, the Coulomb gap, Δ, the rigid gap, γ, and the localization radius, a, on pressure, p, are observed in LaMnO3+δ. It has been established that the dependences above can be interpreted by increase of the electron bandwidth and decrease of the polaron potential well when p is increased. Generally, pressure stimulates delocalization of the electrons in LaMnO3+δ. Doping of LaMnO3 with Ca, leading to La1-xCaxMnO3, changes the Mn3+/Mn4+ ratio significantly and brings an additional disorder to the crystal lattice. Phase separation in a form of mixture of the ferromagnetic and the spin glass phases was observed and investigated in La1- xCaxMnO3 at x between 0 and 0.4. Influence of the replacement of Mn by Fe is studied in La0.7Ca0.3Mn1−yFeyO3 and La0.7Sr0.3Mn1−yFeyO3. Asymmetry of the soft Coulomb gap and of the rigid gap in the density of localized states, small shift of the centre of the gaps with respect to the Fermi level and cubic asymmetry of the density of states are obtained in La0.7Ca0.3Mn1−yFeyO3. Damping of TC with y is connected to breaking of the double-exchange interaction by doping with Fe, whereas the irreversibility and the critical behavior of the magnetic susceptibility are determined by the phase separation and the frustrated magnetic state of La0.7Sr0.3Mn1−yFeyO3.

Patient Seclusion and Restraint Practices in Psychiatric Hospitals - Towards Evidence Based Clinical Nursing

The overall goal of this study was to support evidence based clinical nursing regarding patient seclusion and restraint practices. This was done by ensuring professional competence through innovative learning methods. The data were collected in three phases between March 2007 and May 2009 on acute psychiatric wards. Firstly, psychiatric inpatients’ experiences and suggestions for seclusion and restraint practices were explored (n=30). Secondly, nursing and medical personnel’s perceptions of seclusion and restraint practices were explored (n=27). Thirdly, the impacts of a continuing vocational eLearning course on nurses’ professional competence was evaluated (n=158). Patients’ perspectives received insufficient attention during the seclusion and restraint process. Improvements and alternatives to seclusion and restraint as suggested by the patients focused on essential parts of clinical nursing, but were not extensively adopted. Also nursing and medical personnel thought that patients’ subjective perspective received little attention. Personnel proposed a number of alternatives to seclusion and restraint, and they expressed a need for education and support to adopt these in clinical nursing. Evaluation of impacts of eLearning course on nurses’ professional competence showed no statistical differences between an eLearning group and an education-as-usual group. This dissertation provides evidence based knowledge about the realization of seclusion and restraint practices and the impacts of eLearning course on nurses’ professional competence in psychiatric hospitals. In order to improve clinical nursing the patient perspective must be accentuated. To ensure personnel’s professional competence, there is a need for written clinical guidelines, education and support. Continuing vocational education should bring together written clinical guidelines, ethical and legal issues and the support for personnel. To achieve the ambitious goal of such integration, achievable and affordable educational programmes are required. This, in turn, yields a call for innovative learning methods.

Integrating environmental education in primary school education in Tanzania : teachers’ perceptions and teaching practices

The study focuses on primary school teachers’ perceptions of environmental education, its integration into primary school education and teachers’ teaching practices in Tanzania. The thesis is based on empirical research. The theoretical underpinnings of the study are based on Palmer’s (1998) model of environmental education. According to the model, meaningful environmental education should include education about, in or through and for the environment. The study is supported by national and international literature from research done on environmental education and education for sustainable development and policy statements. The study is qualitative in nature, adopting phenomenography and phenomenology as points of departure. The empirical data was collected from four primary schools in Morogoro region in Tanzania. The study sample consisted of 31 primary school teachers. Data was collected through interviews and lesson observations. According to the results of the study, primary school teachers expressed variations in their perceptions of environmental education and education for sustainable development. Most of the teachers focused on the aspect of knowledge acquisition. According to Tanzanian education and training policy, environmental education has to be integrated into all subjects. Although there is environmental education in the primary school curriculum, it is not integrated on an equal footing in all subjects. Some subjects like science, social studies and geography have more environmental content than other subjects. Teachers claim that the approach used to integrate environmental education into the school curriculum was not favoured because many claimed that what is to be taught as environmental education in the various subjects is not shown clearly. As a result, many teachers suggested that to ensure that it is taught properly it should be included in the curriculum as an independent subject or as specific topics. The study revealed that teachers’ teaching practices in integrating environmental education varied from one subject to another. Although most of the teachers said that they used participatory methods, lesson observations showed that they limited themselves to question and answer and group discussion. However, the teachers faced a number of barriers in the teaching of environmental education, some of which include lack of teaching and learning resources, time and large class size. The role of teachers in the implementation of environmental education in developing an environmentally literate citizenry is of great significance. The responsibility of the government in developing a curriculum with clear goals and content, developing teachers’ capacity in the teaching of environmental education and provision of teaching and learning materials needs to be taken seriously by the government in educational plans and programs.

Finnish Critical Industries, Maritime Transport Vulnerabilities and societal Implications

Maritime transports are very essential for Finland as over 80% of the foreign trade in the country is seaborne and possibilities to carry out these transports by are limited. Any disruption in maritime transports has negative consequences to many sectors in the Finnish economy. Maritime transport thus represents critical infrastructure for Finland. This report focuses on the importance of maritime transports on security of supply in Finland and for the so called critical industries in particular. The report summarizes the results of the Work Package 2 of the research project STOCA – “Study of cargo flows in the Gulf of Finland in emergency situations”. The aim of the research was to analyze the cargo flows and infrastructure that are vital for maintaining security of supply in Finland, as well as the consequences of disruptions in the maritime traffic for the Finnish critical industries and for the Finnish society. In the report we give a presentation of the infrastructure and transport routes which are critical for maintaining security of supply in Finland. We discuss import dependency of the critical industries, and the importance of the Gulf of Finland ports for Finland. We assess vulnerabilities associated with the critical material flows of the critical industries, and possibilities for alternative routings in case either one or several of the ports in Finland would be closed. As a concrete example of a transport disruption we analyze the consequences of the Finnish stevedore strike at public ports (4.3.–19.3.2010). The strike stopped approximately 80% of the Finnish foreign trade. As a result of the strike Finnish companies could not export their products and/or import raw materials, components and spare parts, or other essential supplies. We carried out personal interviews with representatives of the companies in Finnish critical industries to find out about the problems caused by the strike, how companies carried out they transports and how they managed to continue their operations during the strike. Discussions with the representatives of the companies gave us very practical insights about companies’ preparedness towards transport disruptions in general. Companies in the modern world are very vulnerable to transport disruptions because companies regardless of industries have tried to improve their performance by optimizing their resources and e.g. by reducing their inventory levels. At the same time they have become more and more dependent on continuous transports. Most companies involved in foreign trade have global operations and global supply chains, so any disruption anywhere in the world can have an impact on the operations of the company causing considerable financial loss. The volcanic eruption in Iceland in April 2010 stopping air traffic in the whole Northern Europe and most recently the earth quake causing a tsunami in Japan in March 2011 are examples of severe disruptions causing considerable negative impacts to companies’ supply chains. Even though the Finnish stevedore strike was a minor disruption compared to the natural catastrophes mentioned above, it showed the companies’ vulnerability to transport disruptions very concretely. The Finnish stevedore strike gave a concrete learning experience of the importance of preventive planning for all Finnish companies: it made them re-think their practical preparedness towards transport risks and how they can continue with their daily operations despite the problems. Many companies realized they need to adapt their long-term countermeasures against transport disruptions. During the strike companies did various actions to secure their supply chains. The companies raised their inventory levels before the strike began, they re-scheduled or postponed their deliveries, shifted customer orders between production plants among their company’s production network or in the extreme case bought finished products from their competitor to fulfil their customers’ order. Our results also show that possibilities to prepare against transport disruptions differ between industries. The Finnish society as a whole is very dependent on imports of energy, various raw materials and other supplies needed by the different industries. For many of the Finnish companies in the export industries and e.g. in energy production maritime transport is the only transport mode the companies can use due to large volumes of materials transported or due to other characteristics of the goods. Therefore maritime transport cannot be replaced by any other transport mode. In addition, a significant amount of transports are concentrated in certain ports. From a security of supply perspective attention should be paid to finding ways to decrease import dependency and ensuring that companies in the critical industries can ensure the continuity of their operations.

Charge transport in disordered materials : simulations, theory, and numerical modeling of hopping transport and electron-hole recombination

Min avhandling behandlar hur oordnade material leder elektrisk ström. Bland materialen som studeras finns ledande polymerer, d.v.s. plaster som leder ström, och mer allmänt organiska halvledare. Av de här materialen har man kunnat bygga elektroniska komponenter, och man hoppas på att kunna trycka hela kretsar av organiska material. För de här tillämpningarna är det viktigt att förstå hur materialen själva leder elektrisk ström. Termen oordnade material syftar på material som saknar kristallstruktur. Oordningen gör att elektronernas tillstånd blir lokaliserade i rummet, så att en elektron i ett visst tillstånd är begränsad t.ex. till en molekyl eller ett segment av en polymer. Det här kan jämföras med kristallina material, där ett elektrontillstånd är utspritt över hela kristallen (men i stället har en väldefinierad rörelsemängd). Elektronerna (eller hålen) i det oordnade materialet kan röra sig genom att tunnelera mellan de lokaliserade tillstånden. Utgående från egenskaperna för den här tunneleringsprocessen, kan man bestämma transportegenskaperna för hela materialet. Det här är utgångspunkten för den så kallade hopptransportmodellen, som jag har använt mig av. Hopptransportmodellen innehåller flera drastiska förenklingar. Till exempel betraktas elektrontillstånden som punktformiga, så att tunneleringssannolikheten mellan två tillstånd endast beror på avståndet mellan dem, och inte på deras relativa orientation. En annan förenkling är att behandla det kvantmekaniska tunneleringsproblemet som en klassisk process, en slumpvandring. Trots de här grova approximationerna visar hopptransportmodellen ändå många av de fenomen som uppträder i de verkliga materialen som man vill modellera. Man kan kanske säga att hopptransportmodellen är den enklaste modell för oordnade material som fortfarande är intressant att studera. Man har inte hittat exakta analytiska lösningar för hopptransportmodellen, därför använder man approximationer och numeriska metoder, ofta i form av datorberäkningar. Vi har använt både analytiska metoder och numeriska beräkningar för att studera olika aspekter av hopptransportmodellen. En viktig del av artiklarna som min avhandling baserar sig på är att jämföra analytiska och numeriska resultat. Min andel av arbetet har främst varit att utveckla de numeriska metoderna och applicera dem på hopptransportmodellen. Därför fokuserar jag på den här delen av arbetet i avhandlingens introduktionsdel. Ett sätt att studera hopptransportmodellen numeriskt är att direkt utföra en slumpvandringsprocess med ett datorprogram. Genom att föra statisik över slumpvandringen kan man beräkna olika transportegenskaper i modellen. Det här är en så kallad Monte Carlo-metod, eftersom själva beräkningen är en slumpmässig process. I stället för att följa rörelsebanan för enskilda elektroner, kan man beräkna sannolikheten vid jämvikt för att hitta en elektron i olika tillstånd. Man ställer upp ett system av ekvationer, som relaterar sannolikheterna för att hitta elektronen i olika tillstånd i systemet med flödet, strömmen, mellan de olika tillstånden. Genom att lösa ekvationssystemet fås sannolikhetsfördelningen för elektronerna. Från sannolikhetsfördelningen kan sedan strömmen och materialets transportegenskaper beräknas. En aspekt av hopptransportmodellen som vi studerat är elektronernas diffusion, d.v.s. deras slumpmässiga rörelse. Om man betraktar en samling elektroner, så sprider den med tiden ut sig över ett större område. Det är känt att diffusionshastigheten beror av elfältet, så att elektronerna sprider sig fortare om de påverkas av ett elektriskt fält. Vi har undersökt den här processen, och visat att beteendet är väldigt olika i endimensionella system, jämfört med två- och tredimensionella. I två och tre dimensioner beror diffusionskoefficienten kvadratiskt av elfältet, medan beroendet i en dimension är linjärt. En annan aspekt vi studerat är negativ differentiell konduktivitet, d.v.s. att strömmen i ett material minskar då man ökar spänningen över det. Eftersom det här fenomenet har uppmätts i organiska minnesceller, ville vi undersöka om fenomenet också kan uppstå i hopptransportmodellen. Det visade sig att det i modellen finns två olika mekanismer som kan ge upphov till negativ differentiell konduktivitet. Dels kan elektronerna fastna i fällor, återvändsgränder i systemet, som är sådana att det är svårare att ta sig ur dem då elfältet är stort. Då kan elektronernas medelhastighet och därmed strömmen i materialet minska med ökande elfält. Elektrisk växelverkan mellan elektronerna kan också leda till samma beteende, genom en så kallad coulombblockad. En coulombblockad kan uppstå om antalet ledningselektroner i materialet ökar med ökande spänning. Elektronerna repellerar varandra och ett större antal elektroner kan leda till att transporten blir långsammare, d.v.s. att strömmen minskar.