Cultural differences affecting claim handling process and perceived quality in Finnish-Japanese paperboardbusiness

Tutkimuksen tavoitteena oli selvittää Suomen ja Japanin välisten kulttuurierojen vaikutus valitustenkäsittelyprosessiin ja laatukäsityksiin case-yrityksen ja sen asiakkaiden välillä. Teoreettisen viitekehyksen muodostamisessa käytettiin näkemyksiä kulttuurista, kulttuurienvälisestä viestinnästä, valitustenkäsittelystä ja laatukäsityksistä. Kulttuurierojen tarkastelemiseksi esiteltiin kulttuurien ulottuvuuksia eritteleviä viitekehyksiä ja kulturaalisten tekijöiden vaikutusta viestintään. Suomen ja Japanin kulttuureja esiteltiin myös yksityiskohtaisemmin aikaisempien tutkimusten valossa. Työn empiirisessä osassa tutkittiin case-yrityksen sisäisiä sekä yrityksen ja sen asiakkaiden välisiä näkemyseroja. Tutkimus suoritettiin laadullisena case-tutkimuksena, jossa tarkasteltiin myös toimenpiteitä case-yrityksen liiketoimintaympäristön parantamiseksi. Tarvittava tieto kerättiin kirjallisuudesta, artikkeleista, taustahaastatteluilla sekä haastattelemalla yrityksen henkilöstöä Suomessa ja Japanissa samoin kuin sen japanilaisia asiakkaita. Japanilaiset asiakas/toimittaja-suhteet ovat ulkomaalaiselle yritykselle haastava liiketoimintaympäristö. Luottamuksen rakentaminen pitkällä tähtäimellä vaatii läheistä kommunikointia vastapuolen tuntemiseksi, jotta voidaan kehittää tuotteita paremmiksi ja vähentää valituskustannuksia. Laatuajattelua tulee myös yhdenmukaistaa tuotteiden ja palvelujen laadun parantamiseksi.

Developing Support for Scenario Process: A Scenario Study on Lappeenranta University of Technology from 2006 to 2016

Epävarmuus ei ole outoa enää julkishallinon alueellakaan. Globalisaation,tietotalous ja muut yksityissektoria ravistelleet ilmiöt ovat lisänneet mielenkiintoa erilaisiin tekniikoihin joilla voidaan lievittää epävarmuudesta aiheutuvia ongelmia. Tämä raportti kuvailee skenaariosuunnittelun käyttöä eräänä mahdollisuutena epävarmuuden hallintaan julkishallinnossa ja yksityissektorilla. Raportti sijoittuu samaan skenaariotutkimuksen jatkumoon edellisten LTY:ssä toteutettujen skenaariotutkimusten kanssa. tutkimus valottaa tutkimuksen ja käytännön työn nykytilaa helposti hyödynnettävässä muodossa. Rapostin kontribuutio on kuvata tutkimukseen perustuva tuettu skenaarioprosessi ja syntyneet skenaariot, keskittyen prosessin tukemiseen eri menetelmin.

Deregulation of Railroads and Future Development Scenarios in Europe - Literature Analysis of Privatization Process Taken Place in US, UK and Sweden

Euroopan unionissa päätettiin jo yli vuosikymmen sitten, että rautatieliiketoiminta vapautetaan kilpailulle. Iso-Britanniasta olimäärä tulla esimerkkivaltio tämän prosessin käyttöönotossa. Pääideana oli säännöstelyn keventäminen, jolloin omistuspohja toimialalla laajenee ja rautateiden infrastruktuuri sekä toiminta parantuvat. Infrastruktuuri on määrä olla yhden organisaation hallinnassa ja raiteiden käyttöoikeus on kaikilla lupaehdot täyttävillä operaattoreilla, jotka kilpailevat keskenään matkustajista ja tavararahdeista. Kuitenkin Yhdysvalloissa ja eräissä Latinalaisen Amerikan maissa kilpailu on vapautettu siten, että rautatieyritys omistaa raideinfrastruktuurin, junat, tavarankuljetus- sekä matkustajavaunut. Iso-Britannian yksityistämistä pidettiin aluksi isonaepäonnistumisena: nopealla aikataululla sovellettiin jäykkiä transaktioperusteisia ulkoistamisstrategioita infrastruktuurin kunnossapitoon, jotka lopulta johtivat junien jatkuviin myöhästymisiin ja muutamaan tuhoisaan onnettomuuteen. Liiketoiminnallisessa mielessäkään ei oikein onnistuttu: infrastruktuurista vastaava yritys jouduttiin listaamaan pois Lontoon pörssistä, ja hallituksen oli pakko luoda tukipaketti pahasti velkaantuneen, vain marginaalisien investointien kohteena olleen yrityksen toimintaa varten (vaikka kapasiteettitarvetta oli markkinoilla). Myös rautatieoperaattorit olivat taloudellisessa ahdingossa ja vain määrätietoisten hallituksen laatimien pelastuspakettien avulla ala nousi syvimmästä kriisistään. Tästä huolimatta näiden negatiivisten sivuvaikutusten ohella koko ala pystyi kasvattamaan kysyntää, niin matkustaja- kuin rahtiliikenteenkin osalta. Vähenevän kysynnän trendi, joka alkoi 1970-luvulla, otti käännöksen parempaan. Toinen eurooppalaismaa, jolla on pitkät kokemukset yksityistämisestä, on Ruotsi. Tämä maatapaus on melko konservatiivinen verrattuna tilanteeseen edellisessä; vain rajattu määrä reittejä on avattu kilpailulle ja sopimukset tehdään kerralla pitkäksi aikaa eteenpäin. Ruotsin säännöstelyn purku osoittautui menestykseksi, koska tuottavuus onollut vakaassa kasvussa ja rautateiden markkinaosuus erityisesti matkustajapuolella on noussut merkittävästi, verrattuna muihin kuljetusmuotoihin. Kuitenkin kilpailua on käytännössä vähän tässä maassa ja parempiatuloksia on lupa odottaa, kun vain säännöstelyn purkaminen jatkuu. Viimeinen tutkimuksemme kohteena oleva maa on Yhdysvallat, joka alistutti rautatiet kilpailulle jo 1980-luvun alussa, käyttäen jo edellä mainittua vertikaalista integraatiota; tämä valinta on taas johtanut hyvin erilaisiin tuloksiin. Vaihtoehtoinen rakenteellinen uudistustapa on suosinut rahtivirtoja matkustajiin nähden, ja lopputuloksena tämä tapaus synnytti yrityksiä huolehtimaan toista näistä kahdesta pääasiakasryhmästä. Viimeaikaiset tulokset tästä yksityistämisprosessista ovat olleet hyviä: jäljellejääneiden yritysten voitot ovat kasvaneet, osinkoja ollaan kyetty jakamaan ja osakkeiden arvostus on noussut. Tässä tutkimusraportissa yritämme kolmen maatapauksen kautta esittää, miten yksityistämisprosessi tulee vaikuttamaan Euroopassa, kun kilpailu rautateillä vapautuu. Me käymmeläpi, mikä näistä kolmesta maaesimerkistä on kaikkein todennäköisin jaesitämme ehdotuksia siihen, miten valtiot voisivat välttää ei-haluttuja sivuvaikutuksia. Kolme maaesimerkkiä, ja lopuksi esitetty lyhyt tilastollinen analyysi osoittavat, että rautateillä on tulevaisuuden potentiaalia Euroopassa, ja kilpailun vapauttaminen on avain tämän potentiaalin realisointiin.

Value added logistical support service Part 2. Outsourcing process of spare part logistics in metal industry

The aim of this research study was to find out guidelines for outsourcing of logistics processes. The study was outlined to spare parts and `business-to-business' (B2B) markets in metal industry. This study can be applied as a manual for outsourcing especially warehousing and transportation activities. The study also touches other important areas of spare part logistics like manufacturing, customer service, procurement, quality control, reverse and recycling logistics, logistics technologies and valueadded services. The method of study consisted of three areas. Firstly exchanging views with logistics experts in participating companies, and secondly compiling material based on author's practical experience in logistics business with several international and domestic logistics service providers and vendors. Thirdlythe study includes also references to literature material. Due to the fact thatthe outsourcing of logistics functions can be handled widely and from differentpoint of views, in this study it is concentrated mainly on giving general levelguidelines for defining logistics strategy, hints both for tendering process and implementation project, and not forgetting the aftercare of business partnership.

Aspects on Process Engineering in the Finnish Pulp and Paper Industry : Thesis for the Degree of Licentiate in Science of Technology

Process development will be largely driven by the main equipment suppliers. The reason for this development is their ambition to supply complete plants or process systems instead of single pieces of equipment. The pulp and paper companies' interest lies in product development, as their main goal is to create winning brands and effective brand management. Design engineering companies will find their niche in detail engineering based on approved process solutions. Their development work will focus on increasing the efficiency of engineering work. Process design is a content-producing profession, which requires certain special characteristics: creativity, carefulness, the ability to work as a member of a design team according to time schedules and fluency in oral as well as written presentation. In the future, process engineers will increasingly need knowledge of chemistry as well as information and automation technology. Process engineering tools are developing rapidly. At the moment, these tools are good enough for static sizing and balancing, but dynamic simulation tools are not yet good enough for the complicated chemical reactions of pulp and paper chemistry. Dynamic simulation and virtual mill models are used as tools for training the operators. Computational fluid dynamics will certainlygain ground in process design.

Conflict-based Method for Conceptual Process Synthesis

The changing business environment demands that chemical industrial processes be designed such that they enable the attainment of multi-objective requirements and the enhancement of innovativedesign activities. The requirements and key issues for conceptual process synthesis have changed and are no longer those of conventional process design; there is an increased emphasis on innovative research to develop new concepts, novel techniques and processes. A central issue, how to enhance the creativity of the design process, requires further research into methodologies. The thesis presentsa conflict-based methodology for conceptual process synthesis. The motivation of the work is to support decision-making in design and synthesis and to enhance the creativity of design activities. It deals with the multi-objective requirements and combinatorially complex nature of process synthesis. The work is carriedout based on a new concept and design paradigm adapted from Theory of InventiveProblem Solving methodology (TRIZ). TRIZ is claimed to be a `systematic creativity' framework thanks to its knowledge based and evolutionary-directed nature. The conflict concept, when applied to process synthesis, throws new lights on design problems and activities. The conflict model is proposed as a way of describing design problems and handling design information. The design tasks are represented as groups of conflicts and conflict table is built as the design tool. The general design paradigm is formulated to handle conflicts in both the early and detailed design stages. The methodology developed reflects the conflict nature of process design and synthesis. The method is implemented and verified through case studies of distillation system design, reactor/separator network design and waste minimization. Handling the various levels of conflicts evolve possible design alternatives in a systematic procedure which consists of establishing an efficient and compact solution space for the detailed design stage. The approach also provides the information to bridge the gap between the application of qualitative knowledge in the early stage and quantitative techniques in the detailed design stage. Enhancement of creativity is realized through the better understanding of the design problems gained from the conflict concept and in the improvement in engineering design practice via the systematic nature of the approach.

The Influence of Process Conditions on the Deresination Efficiency in Mechanical Pulp Washing

The aim of this thesis was to produce information for the estimation of the flow balance of wood resin in mechanical pulping and to demonstrate the possibilities for improving the efficiency of deresination in practice. It was observed that chemical changes in wood resin take place only during peroxide bleaching, a significant amount of water dispersed wood resin is retained in the pulp mat during dewatering and the amount of wood resin in the solid phase of the process filtrates is very small. On the basis of this information there exist three parameters related to behaviour of wood resin that determine the flow balance in the process: 1. The liberation of wood resin to the pulp water phase 2. Theretention of water dispersed wood resin in dewatering 3. The proportion of wood resin degraded in the peroxide bleaching The effect of different factors on these parameters was evaluated with the help of laboratory studies and a literature survey. Also, information related to the values of these parameters in existing processes was obtained in mill measurements. With the help of this information, it was possible to evaluate the deresination efficiency and the effect of different factors on this efficiency in a pulping plant that produced low-freeness mechanical pulp. This evaluation showed that the wood resin content of mechanical pulp can be significantly decreased if there exists, in the process, a peroxide bleaching and subsequent washing stage. In the case of an optimal process configuration, as high as a 85 percent deresination efficiency seems to be possible with a water usage level of 8 m3/o.d.t.

Development of fibre recovery process

The fiber recovery process is an essential part of the modern paper mill. It creates the basisfor mill's internal recirculation of the most important raw materials ¿ water and fiber. It is normally also a start point for further treatment of wastewater and if it works efficiently, it offers excellent basis to minimize effluents. This dissertation offers two different approaches to the subject. Firstly a novel save-all disc filter feeding system is developed and presented. This so-called precoat method is tested both in the laboratory and full-scale conditions. In laboratory scale it beats the traditional one clearly, when low freeness pulps are used as a sweetener stock. The full-scale application needs still some development work before it can be implemented to the paper mills. Secondly, the operationenvironment of save-all disc filter is studied mostly in laboratory conditions.The focus of this study is in cases, where low-freeness pulps are used as a sweetener stock of save-all filter. The effects of CSF-value, pressure drop, suspension consistency and retention chemicals to the quantity and quality of the filtrate was studied. Also the filtration resistance of the low freeness pulps was one studied.

Wet Oxidation of Concentrated Wastewaters: Process Combination and Reaction Kinetic Modeling

The accumulation of aqueous pollutants is becoming a global problem. The search for suitable methods and/or combinations of water treatment processes is a task that can slow down and stop the process of water pollution. In this work, the method of wet oxidation was considered as an appropriate technique for the elimination of the impurities present in paper mill process waters. It has been shown that, when combined with traditional wastewater treatment processes, wet oxidation offers many advantages. The combination of coagulation and wet oxidation offers a new opportunity for the improvement of the quality of wastewater designated for discharge or recycling. First of all, the utilization of coagulated sludge via wet oxidation provides a conditioning process for the sludge, i.e. dewatering, which is rather difficult to carry out with untreated waste. Secondly, Fe2(SO4)3, which is employed earlier as a coagulant, transforms the conventional wet oxidation process into a catalytic one. The use of coagulation as the post-treatment for wet oxidation can offer the possibility of the brown hue that usually accompanies the partial oxidation to be reduced. As a result, the supernatant is less colored and also contains a rather low amount of Fe ions to beconsidered for recycling inside mills. The thickened part that consists of metal ions is then recycled back to the wet oxidation system. It was also observed that wet oxidation is favorable for the degradation of pitch substances (LWEs) and lignin that are present in the process waters of paper mills. Rather low operating temperatures are needed for wet oxidation in order to destruct LWEs. The oxidation in the alkaline media provides not only the faster elimination of pitch and lignin but also significantly improves the biodegradable characteristics of wastewater that contains lignin and pitch substances. During the course of the kinetic studies, a model, which can predict the enhancements of the biodegradability of wastewater, was elaborated. The model includes lumped concentrations suchas the chemical oxygen demand and biochemical oxygen demand and reflects a generalized reaction network of oxidative transformations. Later developments incorporated a new lump, the immediately available biochemical oxygen demand, which increased the fidelity of the predictions made by the model. Since changes in biodegradability occur simultaneously with the destruction of LWEs, an attempt was made to combine these two facts for modeling purposes.

Supporting knowledge creation and sharing in the early phases of the strategic innovation process

The driving forces of technology and globalization continuously transform the business landscape in a way which undermines the existing strategies and innovations of organizations. The challenge for organizations is to establish such conditions where they are able to create new knowledge for innovative business ideas in interaction between other organizations and individuals. Innovation processes continuously need new external stimulations and seek new ideas, new information and knowledge locating more and more outside traditional organizational boundaries. In several studies, the early phases of the innovation process have been considered as the most critical ones. During these phases, the innovation process can emerge or conclude. External knowledge acquirement and utilization are noticed to be important at this stage of the innovation process giving information about the development of future markets and needs for new innovative businessideas. To make it possible, new methods and approaches to manage proactive knowledge creation and sharing activities are needed. In this study, knowledge creation and sharing in the early phases of the innovation process has been studied, and the understanding of knowledge management in the innovation process in an open and collaborative context advanced. Furthermore, the innovation management methods in this study are combined in a novel way to establish an open innovation process and tested in real-life cases. For these purposes two complementary and sequentially applied group work methods - the heuristic scenario method and the idea generation process - are examined by focusing the research on the support of the open knowledge creation and sharing process. The research objective of this thesis concerns two doctrines: the innovation management including the knowledge management, and the futures research concerning the scenario paradigm. This thesis also applies the group decision support system (GDSS) in the idea generation process to utilize the converged knowledge during the scenario process.

Mobile Communications within the European Union: The Role of Location in the Evolution and Forecasting of the Diffusion Process

In the European Union, the importance of mobile communications was realized early on. The process of mobile communications becoming ubiquitous has taken time, as the innovation of mobile communications diffused into the society. The aim of this study is to find out how the evolution and spatial patterns of the diffusion of mobile communications within the European Union could be taken into account in forecasting the diffusion process. There is relatively lot of research of innovation diffusion on the individual (micro) andthe country (macro) level, if compared to the territorial level. Territorial orspatial diffusion refers either to the intra-country or inter-country diffusionof an innovation. In both settings, the dif- fusion of a technological innovation has gained scarce attention. This study adds knowledge of the diffusion between countries, focusing especially on the role of location in this process. The main findings of the study are the following: The penetration rates of the European Union member countries have become more even in the period of observation, from the year 1981 to 2000. The common digital GSM system seems to have hastened this process. As to the role of location in the diffusion process, neighboring countries have had similar diffusion processes. They can be grouped into three, the Nordic countries, the central and southern European countries, and the remote southern European countries. The neighborhood effect is also domi- nating in thegravity model which is used for modeling the adoption timing of the countries. The subsequent diffusion within a country, measured by the logistic model in Finland, is af- fected positively by its economic situation, and it seems to level off at some 92 %. Considering the launch of future mobile communications systemsusing a common standard should implicate an equal development between the countries. The launching time should be carefully selected as the diffusion is probably delayed in economic downturns. The location of a country, measured by distance, can be used in forecasting the adoption and diffusion. Fi- nally, the result of penetration rates becoming more even implies that in a relatively homoge- nous set of countries, such as the European Union member countries, the estimated final pene- tration of a single country can be used for approximating the penetration of the others. The estimated eventual penetration of Finland, some 92 %, should thus also be the eventual level for all the European Union countries and for the European Union as a whole.

Welding time models for cost calculations in the early stages of the design process

It is generally accepted that between 70 and 80% of manufacturing costs can be attributed to design. Nevertheless, it is difficult for the designer to estimate manufacturing costs accurately, especially when alternative constructions are compared at the conceptual design phase, because of the lack of cost information and appropriate tools. In general, previous reports concerning optimisation of a welded structure have used the mass of the product as the basis for the cost comparison. However, it can easily be shown using a simple example that the use of product mass as the sole manufacturing cost estimator is unsatisfactory. This study describes a method of formulating welding time models for cost calculation, and presents the results of the models for particular sections, based on typical costs in Finland. This was achieved by collecting information concerning welded products from different companies. The data included 71 different welded assemblies taken from the mechanical engineering and construction industries. The welded assemblies contained in total 1 589 welded parts, 4 257 separate welds, and a total welded length of 3 188 metres. The data were modelled for statistical calculations, and models of welding time were derived by using linear regression analysis. Themodels were tested by using appropriate statistical methods, and were found to be accurate. General welding time models have been developed, valid for welding in Finland, as well as specific, more accurate models for particular companies. The models are presented in such a form that they can be used easily by a designer, enabling the cost calculation to be automated.

Procurement in Project Implementation

Tutkimus keskittyy hankintatoimen kehittämiseen osana laitosprojektien toteutusta. Työ pohjautuu empiiriseltä taustaltaan Pöyry Oyj:n projektiliiketoimintaan ja työn tarkastelunäkökulmaksi onvalittu projektihallinnosta vastaavan yrityksen näkökulma. Tutkimus on hyvin käytännönläheinen ¿ se lähtee hankinnan ja sen seurannan ongelmista ja pyrkii tarjoamaan niihin uudenlaisia ratkaisuja. Pohjimmiltaan tutkimus kuuluu teollisuustalouden piiriin, vaikka tietojärjestelmätieteellä on vahva tukirooli. Työn tavoitteet ja tulokset liittyvät teollisuustaloudelle ominaisesti yrityksen toiminnan kehittämiseen, käytetyt välineet ja ratkaisut puolestaan hyödyntävät tietojärjestelmätieteen antamia mahdollisuuksia. Tutkimuksessa on käytetty konstruktiivista tutkimusotetta, jonka mukaisesti on luotu innovatiivisia konstruktioita ratkaisemaan aitoja reaalimaailman ongelmia ja tätä kautta tuotettu kontribuutioita teollisuustaloudelle. Tavoitteena oli järjestää hankintatoimi ja sen seuranta suurissa laitosprojekteissa tehokkaammin. Tätä varten uudistettiin ensin projektihallinnon ja hankintatoimen toimintaohjeet vastaamaan paremmin nykyajan vaatimuksia. Toimintaohjeiden perusteella ryhdyttiin toteuttamaan hankintaohjelmistoa, joka pystyisi kattamaan kaikki toimintaohjeissa kuvatut piirteet. Lopulta hankintaohjelmisto toi mukanaan uusia piirteitä projektihallintoon ja hankintatoimeen ja nämä sisällytettiin toimintaohjeisiin. Tähän kehitystyöhön ryhdyttiin, jotta laitosprojektien projektihallinto ja hankintatoimi toimisivat paremmin, eli pienemmin kustannuksin tuottaen projekteissa tarvittavat tulokset nopeammin, tarkemmin ja laadukkaammin. Tutkimuksella on kolmenlaisia tuloksia: hankintatoimen parannetut metodit, hankintaohjelmiston pohjana olevat toiminta- ja laskentamallit sekä implementaationa hankintasovellus. Uudistetut projekti- ja hankintaohjeet kuvaavat hankintatoiminnan parannettuja metodeja. Hankintaohjelmistoasuunnitellessa ja kehitettäessä tehdyt kuvaukset sisältävät uusia malleja niin hankintaprosessille kuin hankinnan seuraamiseksi suurissa laitosprojekteissa. Itse ohjelmisto on tuloksena implementaatio, joka perustuu parannettuihin hankintametodeihin ja uusiin toiminta- ja laskentamalleihin. Uudistetut projekti- ja hankintaohjeet ovat olleet käytössä Pöyry Oyj:ssä vuodesta 1991. Vuosien varrella nämä toimintaohjeet ovat auttaneet ja tukeneet satojen laitosprojektientoteutusta ja ylläpitäneet Pöyry Oyj:n kilpailukykyä kansainvälisenä projektitalona. Hankintasovellus puolestaan on ollut käytössä useissa projekteissa ja sen on havaittu pienentävän hankintatoimen suoria työkustannuksia laitosprojekteissa. Sovelluksen katsotaan myös tuovan epäsuoria kustannussäästöjä parempien hankintapäätösten muodossa, mutta näiden säästöjen suuruutta ei pystytä luotettavasti arvioimaan.

Applying the principles of life cycle assessment and costing in process modeling to examine profit-making capability

Static process simulation has traditionally been used to model complex processes for various purposes. However, the use of static processsimulators for the preparation of holistic examinations aiming at improving profit-making capability requires a lot of work because the production of results requires the assessment of the applicability of detailed data which may be irrelevant to the objective. The relevant data for the total assessment gets buried byirrelevant data. Furthermore, the models do not include an examination of the maintenance or risk management, and economic examination is often an extra property added to them which can be performed with a spreadsheet program. A process model applicable to holistic economic examinations has been developed in this work. The model is based on the life cycle profit philosophy developed by Hagberg and Henriksson in 1996. The construction of the model has utilized life cycle assessment and life cycle costing methodologies with a view to developing, above all, a model which would be applicable to the economic examinations of complete wholes and which would require the need for information focusing on aspects essential to the objectives. Life cycle assessment and costing differ from each other in terms of the modeling principles, but the features of bothmethodologies can be used in the development of economic process modeling. Methods applicable to the modeling of complex processes can be examined from the viewpoint of life cycle methodologies, because they involve the collection and management of large corpuses of information and the production of information for the needs of decision-makers as well. The results of the study shows that on the basis of the principles of life cycle modeling, a process model can be created which may be used to produce holistic efficiency examinations on the profit-making capability of the production line, with fewer resources thanwith traditional methods. The calculations of the model are based to the maximum extent on the information system of the factory, which means that the accuracyof the results can be improved by developing information systems so that they can provide the best information for this kind of examinations.