Microwave Processes in Ferrite-ferroelectric Layered Structure

This work is devoted to investigation of wave processes in new hybrid ferrite/ferroelectric structures. Spin wave devices based on ferrite films have disadvanteges. And their applications are limited. Investigated structures allow to overcome disadvantages. This investigation helps to create new class of devices. Electromagnetic analysis of hybrid spin-electromagnetic waves in ferrite/ferroelectric structures were done. As a result dispersion relation was found. Numerical solution of this dispersion relation gave us follow results. These structures can be effectively tuned by external electric and magnetic field. Methods to increase tuning range were suggested. It was found that such structures have one basic disadvantage which is connected with presence of thick ferroelectric layer. To solve this problem is to use thin ferroelectric films. But this decreases tuning range. It was confirmed by experiment that this structures can be effectively tuned by electric and magnetic fields. Resonance characteristics of ferrite/ferroelectric resonator were succesfully tuned by magnetic and electric field.

Quality and analysis of administration processes in server operations

IT outsourcing refers to the way companies focus on their core competencies and buy the supporting functions from other companies specialized in that area. Service is the total outcome of numerous of activities by employees and other resources to provide solutions to customers' problems. Outsourcing and service business have their unique characteristics. Service Level Agreements quantify the minimum acceptable service to the user. The service quality has to be objectively quantified so that its achievement or non-achievement of it can be monitored. Usually offshoring refers to the transferring of tasks to low-cost nations. Offshoring presents a lot of challenges that require special attention and they need to be assessed thoroughly. IT Infrastructure management refers to installation and basic usability assistance of operating systems, network and server tools and utilities. ITIL defines the industry best practices for organizing IT processes. This thesis did an analysis of server operations service and the customers’ perception of the quality of daily operations. The agreed workflows and processes should be followed better. Service providers’ processes are thoroughly defined but both the customer and the service provider might disobey them. Service provider should review the workflows regarding customer functions. Customer facing functions require persistent skill development, as they communicate the quality to the customer. Service provider needs to provide better organized communication and knowledge exchange methods between the specialists in different geographical locations.

Finnair Technical Procurement’s Processes and Service Quality

As primary objective, this thesis examines Finnair Technical Procurement’s service quality with its underlying process. As an internal unit, Technical Procurement serves as a link between external suppliers and internal customers. It is argued that external service quality requires a certain quality level within an organization. At the same time, aircraft maintenance business is subject to economic restraints. Therefore, a methodology was developed with a modified House of Quality that assists management in analyzing and evaluating Technical Procurement’s service level and connected process steps. It could be shown that qualitative and quantitative objectives do not exclude each other per se.

Understanding change processes in business networks : a study of convergence in Finnish telecommunications 1985-2005

Aktörer inom telekommunikationsbranschen i Finland har genomgått en intensiv förändring under de senaste 25 åren, från 1980-talets självständiga företag till företag beroende av varandra, och även av aktörer inom närliggande branscher. I dag skapas telekommunikationsmarknaden inte endast av operatörerna, utan också av mediebolag (t.ex. MTV Media) och IT-företag (t.ex. TietoEnator). Gränserna mellan olika industrier håller därmed på att suddas ut - ett fenomen som allmänt benämns som teknologisk konvergens. Konvergens innebär att någonting integreras; det kan handla om t.ex. teknologier (telefoni och Internet), företag (AOL och Time Warner), industrier (telekom, media och IT-branscherna), tjänster (mobilt TV), produkter (PDA) osv. Detta innebär att ytterst få telekomaktörer ensamma kan vidareutveckla marknaden och tekniska lösningar. Samarbete mellan aktörer krävs; mobiltelefontillverkare, innehållsproducenter, operatörer osv. bör intesifiera sitt samarbete för att kunna erbjuda attraktiva tjänster och produkter till kunder och slutanvändare. Avhandlingen fokuserar speciellt på affärsnätverk och samarbetsmönster mellan nätverksaktörer som medel för att få tillgång till resurser som krävs i en konvergenskarakteriserad affärsomgivning. Avhandlingen lyfter fram vad den teknologiska konvergensen har inneburit för telekomaktörer, dvs. att företag tvingats förändra sina strategier och verksamhetsmodeller. För många företag i branschen har anpassningen till konvergenstänkande varit utmanande, och i vissa fall kan man till och med tala om att företagen upplevt en identitetskris. Den utförda forskningen visar att konvergens uppfattas på marknaden som en pågående förändringsprocess, där varje telekomaktör är tvungen att utvärdera sin roll och position i relation till andra aktörer inom branschen. Konvergensprocesser forsätter i framtiden med ökad intensitet. Aktörerna skapar medvetet sin omgivning genom att agera i olika roller, som kan sträcka sig över industrigränser. Avhandlingen påvisar även att externa händelser och industrikontexten påverkar dynamiken i ett affärsnätverk.

Usability of laser–arc hybrid welding processes in industrial applications

Metal industries producing thick sections have shown increasing interest in the laser–arc hybrid welding process because of its clear advantages compared with the individual processes of autogenous laser welding and arc welding. One major benefit of laser–arc hybrid welding is that joints with larger gaps can be welded with acceptable quality compared to autogenous laser welding. The laser-arc hybrid welding process has good potential to extend the field of applications of laser technology, and provide significant improvements in weld quality and process efficiency in manufacturing applications. The objective of this research is to present a parameter set-up for laser–arc hybrid welding processes, introduce a methodical comparison of the chosen parameters, and discuss how this technology may be adopted in industrial applications. The research describes the principles, means and applications of different types of laser–arc hybrid welding processes. Conducted experiment processing variables are presented and compared using an analytical model which can also be used for predictive simulations. The main argument in this thesis is that profound understanding of the advanced technology of laser-arc hybrid welding will help improve the productivity of welding in industrial applications. Based on a review of the current knowledge base, important areas for further research are also identified. This thesis consists of two parts. The first part introduces the research topic and discusses laser–arc hybrid welding by characterizing its mechanism and most important variables. The second part comprises four research papers elaborating on the performance of laser– arc hybrid welding in the joining of metals. The study uses quantitative and qualitative research methods which include in-depth, interpretive analyses of results from a number of research groups. In the interpretive analysis, the emphasis is placed on the relevance and usefulness of the investigative results drawn from other research publications. The results of this study contribute to research on laser–arc hybrid welding by increasing understanding of how old and new perspectives on laser–arc hybrid welding are evidenced in industry. The research methodology applied permits continued exploration of how laser–arc hybrid welding and various process factors influence the overall quality of the weld. Thestudy provides a good foundation for future research, creates improved awareness of the laser–arc hybrid welding process, and assists the metal industry to maximize welding productivity.

Measuring Processes of a New Packaging Solutions with the Balanced Scorecard, case DigiCup

The aim of this study was to create a Balanced Scorecard to the DigiCup solution. The first goal was to create process descriptions to the few critical processes. The second goal was to define appropriate measurements, according to customer survey as well as following the Balanced Scorecard process description, to manage the critical success factors. The overall goal of this study was to create a performance measurement system for the solution which guides the operation towards continuous improvement. This study was conducted by using both qualitative and quantitative methods, and the analysis was done by using a case study method. The material was gathered from the current customers, the management and the employees using structured, semi-structured and open group and individual interviews. The current customers were divided into retailers and direct customers of the DigiCup solution. The questions which the customers were asked were related to the information about interviewee, company, business strategy, market, satisfaction survey and future requirements. The management defined the strategy and took part in specifying the perspectives, objectives and measurements to the Balanced Scorecard of the DigiCup solution. The employees participated into the choosing of the metrics. The material consisted from altogether sixteen interviews. At the beginning of the study the product development, the order-delivery as well as the printing processes was chosen to be the critical processes of the DigiCup solution. These processes were concentrated on already in the literature review while trying to find the characteristics of these processes as well as the critical success factors and the appropriate measurements, which could be utilized when creating the Balanced Scorecard to the DigiCup solution according to the customer survey. The appropriate perspectives, objectives and measurements were found to the DigiCup solution. The chosen measures works as a basis for the development of IT-reporting tool. As a conclusion it can be stated that when discussing a new business, where the objectives are changing according to which development’s phases the company is in, the measurement should be updated often enough.

Evaluation of energy efficiency and best available techniques in pumping processes

The potential for enhancing the energy efficiency of industrial pumping processes is estimated to be in some cases up to 50 %. One way to define further this potential is to implement techniques in accordance to definition of best available techniques in pumping applications. These techniques are divided into three main categories: Design, control method & maintenance and distribution system. In the theory part of this thesis first the definition of best available techniques (BAT) and its applicability on pumping processes is issued. Next, the theory around pumping with different pump types is handled, the main stress being in centrifugal pumps. Other components needed in a pumping process are dealt by presenting different control methods, use of an electric motor, variable speed drive and the distribution system. Last part of the theory is about industrial pumping processes from water distribution, sewage water and power plant applications, some of which are used further on in the empirical part as example cases. For the empirical part of this study four case studies on typical pumping processes from older Master’s these were selected. Firstly the original results were analyzed by studying the distribution of energy consumption between different system components and using the definition of BAT in pumping, possible ways to improve energy efficiency were evaluated. The goal in this study was that by the achieved results it would be possible to identify the characteristic energy consumption of these and similar pumping processes. Through this data it would then be easier to focus energy efficiency actions where they might be the most applicable, both technically and economically.

Recovery and refining of manganese as by-product from hydrometallurgical processes

The consumption of manganese is increasing, but huge amounts of manganese still end up in waste in hydrometallurgical processes. The recovery of manganese from multi-metal solutions at low concentrations may not be economical. In addition, poor iron control typically prevents the production of high purity manganese. Separation of iron from manganese can be done with chemical precipitation or solvent extraction methods. Combined carbonate precipitation with air oxidation is a feasible method to separate iron and manganese due to the fast kinetics, good controllability and economical reagents. In addition the leaching of manganese carbonate is easier and less acid consuming than that of hydroxide or sulfide precipitates. Selective iron removal with great efficiency from MnSO4 solution is achieved by combined oxygen or air oxidation and CaCO3 precipitation at pH > 5.8 and at a redox potential of > 200 mV. In order to avoid gypsum formation, soda ash should be used instead of limestone. In such case, however, extra attention needs to be paid on the reagents mole ratios in order to avoid manganese coprecipitation. After iron removal, pure MnSO4 solution was obtained by solvent extraction using organophosphorus reagents, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and bis(2,4,4- trimethylpentyl)phosphinic acid (CYANEX 272). The Mn/Ca and Mn/Mg selectivities can be increased by decreasing the temperature from the commonly used temperatures (40 –60oC) to 5oC. The extraction order of D2EHPA (Ca before Mn) at low temperature remains unchanged but the lowering of temperature causes an increase in viscosity and slower phase separation. Of these regents, CYANEX 272 is selective for Mn over Ca and, therefore, it would be the better choice if there is Ca present in solution. A three-stage Mn extraction followed by a two-stage scrubbing and two-stage sulfuric acid stripping is an effective method of producing a very pure MnSO4 intermediate solution for further processing. From the intermediate MnSO4 some special Mn- products for ion exchange applications were synthesized and studied. Three types of octahedrally coordinated manganese oxide materials as an alternative final product for manganese were chosen for synthesis: layer structured Nabirnessite, tunnel structured Mg-todorokite and K-kryptomelane. As an alternative source of pure MnSO4 intermediate, kryptomelane was synthesized by using a synthetic hydrometallurgical tailings. The results show that the studied OMS materials adsorb selectively Cu, Ni, Cd and K in the presence of Ca and Mg. It was also found that the exchange rates were reasonably high due to the small particle dimensions. Materials are stable in the studied conditions and their maximum Cu uptake capacity was 1.3 mmol/g. Competitive uptake of metals and acid was studied using equilibrium, batch kinetic and fixed-bed measurements. The experimental data was correlated with a dynamic model, which also accounts for the dissolution of the framework manganese. Manganese oxide micro-crystals were also bound onto silica to prepare a composite material having a particle size large enough to be used in column separation experiments. The MnOx/SiO2 ratio was found to affect significantly the properties of the composite. The higher the ratio, the lower is the specific surface area, the pore volume and the pore size. On the other hand, higher amount of silica binder gives composites better mechanical properties. Birnesite and todorokite can be aggregated successfully with colloidal silica at pH 4 and with MnO2/SiO2 weight ratio of 0.7. The best gelation and drying temperature was 110oC and sufficiently strong composites were obtained by additional heat-treatment at 250oC for 2 h. The results show that silica–supported MnO2 materials can be utilized to separate copper from nickel and cadmium. The behavior of the composites can be explained reasonably well with the presented model and the parameters estimated from the data of the unsupported oxides. The metal uptake capacities of the prepared materials were quite small. For example, the final copper loading was 0.14 mmol/gMnO2. According to the results the special MnO2 materials are potential for a specific environmental application to uptake harmful metal ions.

Making Sense of Shared Leadership. A case study of leadership processes and practices without formal leadership structure in the team context

Leadership is essential for the effectiveness of the teams and organizations they are part of. The challenges facing organizations today require an exhaustive review of the strategic role of leadership. In this context, it is necessary to explore new types of leadership capable of providing an effective response to new needs. The presentday situations, characterized by complexity and ambiguity, make it difficult for an external leader to perform all leadership functions successfully. Likewise, knowledge-based work requires providing professional groups with sufficient autonomy to perform leadership functions. This study focuses on shared leadership in the team context. Shared leadership is seen as an emergent team property resulting from the distribution of leadership influence across multiple team members. Shared leadership entails sharing power and influence broadly among the team members rather than centralizing it in the hands of a single individual who acts in the clear role of a leader. By identifying the team itself as a key source of influence, this study points to the relational nature of leadership as a social construct where leadership is seen as social process of relating processes that are co-constructed by several team members. Based on recent theoretical developments concerned with relational, practice-based and constructionist approaches to the study of leadership processes, this thesis proposes the study of leadership interactions, working processes and practices to focus on the construction of direction, alignment and commitment. During the research process, critical events, activities, working processes and practices of a case team have been examined and analyzed with the grounded theory –approach in the terms of shared leadership. There are a variety of components to this complex process and a multitude of factors that may influence the development of shared leadership. The study suggests that the development process of shared leadership is a common sense -making process and consists of four overlapping dimensions (individual, social, structural, and developmental) to work with as a team. For shared leadership to emerge, the members of the team must offer leadership services, and the team as a whole must be willing to rely on leadership by multiple team members. For these individual and collective behaviors to occur, the team members must believe that offering influence to and accepting it from fellow team members are welcome and constructive actions. Leadership emerges when people with differing world views use dialogue and collaborative learning to create spaces where a shared common purpose can be achieved while a diversity of perspectives is preserved and valued. This study also suggests that this process can be supported by different kinds of meaning-making and process tools. Leadership, then, does not reside in a person or in a role, but in the social system. The built framework integrates the different dimensions of shared leadership and describes their relationships. This way, the findings of this study can be seen as a contribution to the understanding of what constitutes essential aspects of shared leadership in the team context that can be of theoretical value in terms of advancing the adoption and development process of shared leadership. In the real world, teams and organizations can create conditions to foster and facilitate the process. We should encourage leaders and team members to approach leadership as a collective effort that the team can be prepared for, so that the response is rapid and efficient.

Simulation of Solid Processes by Aspen Plus

Solid processes are used for obtaining the valuable minerals. Due to their worth, it is obligatory to perform different experiments to determine the different values of these minerals. With the passage of time, it is becoming more difficult to carry out these experiments for each mineral for different characteristics due to high labor costs and consumption of time. Therefore, scientists and engineers have tried to overcome this issue. They made different software to handle this problem. Aspen is one of those software for the calculation of different parameters. Therefore, the aim of this report was to do simulation for solid processes to observe different effect for minerals. Different solid processes like crushing, screening; filtration and crystallization were simulated by Aspen Plus. The simulation results are obtained by using this simulation software and they are described in this thesis. It was noticed that the results were acceptable for all solid processes. Therefore, this software can be used for the designing of crushers by calculating the power consumption of crushers, can design the filter and for the calculation of material balance for all processes.

Improvement of open innovation processes: case Nokia

Open innovation is becoming increasingly popular in academic literature and in business life, but even if people heard about it, they might not understand what it really is, they may over-estimate it thinking that it is savior or underestimate it, concentrating on limitations and risks. Current work sheds light on most important concepts of open innovation theory. Goal of current research is to offer business processes improvement for both inbound and outbound modes in case company. It is relevant as open innovation proved to affect firms‘ performance in general case and in case company, and Nokia planned to develop open innovation implementation since 2008 but still competitors succeed in it more, therefore analysis of current situation with open innovation in Nokia and recommendations how to improve it are topical. Case study method was used to answer the question ―How open innovation processes can be improved?‖. 11 in-depth interviews with Nokia senior managers and independent consultants were used to reach the goal of the thesis, as well as secondary sources. Results of current work are as-is and to-be models (process models of today and best practices models) of several open innovation modes, and recommendation for case company, which will be presented to company representatives and checked for practical applicability.

Focusing on the quality of learning processes

S. 327-333

Patterns and processes of littoral zooplankton composition in relation to the trophic state of the environment

Avhandlingen handlar om hur kompositionen hos litoralt djurplankton varierar med omgivningens trofiska nivå (m.a.o. eutrofieringsgrad). Arbetets inledande mål är att beskriva hur mängden och artmångfalden hos djurplankton i strandnära vattnen och de omgivande organismsamhällen ändras med närsaltshalter. Huvudsyftet är att utreda allmänna mekanismer som styr dessa mönster och som på så sätt kan vara viktiga i att reglera samhällen även i andra ekologiska system. Undersökningarna gjordes i åländska flador över flera tillväxtsäsonger samt i laboratorier där omgivningsförhållanden i fladorna kunde simuleras och manipuleras. Djurplankton i dessa lagunlika vikar är lägliga modellsystem. Flador är lämpligt avgränsade från det omgivande havet och förekommer allmänt i norra Östersjöregionen. Således kan de inom ett litet område som Åland representera hela regionala gradienten från näringsfattiga till näringsrika förhållanden. De små kräft- och hjuldjuren som djurplankton består av befinner sig i mitten av näringsväven. De sammankopplar olika typer av mikrobiell produktion vidare till högre konsumenter och är på så sätt centrala för organismsamhällens struktur och funktion i nästan alla akvatiska miljöer. I likhet med primärproducenterna (d.v.s. växter och alger som direkt påverkas av närsaltshalterna, och som bl.a. utgör föda och habitat för djurplankton) samvarierar kompositionen hos djurplankton tydligt med omgivningens trofiska nivå tills den blir hög. Sedan börjar hela samhällskompositionen utveckla sig åt två skilda håll. Dessa mönster kan för djurplanktonets del förklaras med att dess komposition ingalunda styrs endast av primärproducenterna, utan av ett komplicerat samspel mellan dessa resurser samt konkurrerande och högre konsumenter (d.v.s. predatorer på flera högre trofinivåer). Detta kom fram speciellt i laboratorieförhållanden då kompositionen hos dessa samhällskomponenter manipulerades. Både deras sammansättning och relativa tätheter i sig, samt en kombination av båda visade sig styra djurplanktonkompositionen. Lokala processer (inom fladorna) och synnerligen förändringar hos olika fundament- (speciellt vass, borstnate och rödsträfse), kärn- (speciellt yngel av a bborre och mört) och nyckelarter (stora predatorer som gädda) verkar kunna avgöra till vilken grad djurplanktonkompositionen samvarierar med omgivningens trofiska nivå. Inte bara samhällen utan också de mekanismer som styr dem ändras med omgivningens trofiska nivå. Flador är ypperliga naturliga laboratorier för att studera dessa och även andra allmänekologiska mönster och mekanismer. De är också oerhört viktiga miljöer för hela kustregionens natur.