Aukko-osuuden mittausmenetelmien kartoitus PWR PACTEL -koelaitteiston pystyhöyrystimen sekundääripuolella

Diplomityössä kartoitetaan mahdollisuuksia aukko-osuuden mittaamiseksi ydinvoimalaitosta mallintavan PWR PACTEL -koelaitteiston pystyhöyrystimen sekundääripuolella. Työ on toteutettu osana kansallista SAFIR2014-ydinturvallisuustutkimusohjelmaa. Diplomityön tavoitteena on löytää kustannuksiltaan mahdollisimman järkevä ja toimiva menetelmä aukko-osuuden määrittämiseksi. Aukko-osuuden mittaaminen on tärkeää sekundääripuolen kaksifaasivirtauksen käyttäytymisen paremman tuntemuksen lisäämiseksi. Aukko-osuusmittausdataa tarvitaan muun muassa laskentakoodien validointiin. Diplomityössä perehdytään kaksifaasivirtauksen ja aukko-osuuden fysiikkaan sekä esitellään erityyppisiä aukko-osuuden mittausmenetelmiä. Kunkin mittausmenetelmän soveltuvuutta PWR PACTEL -koelaitteistoon arvioidaan erikseen. Aukko-osuuden mittaaminen höyrystimen sekundääripuolella osoittautuu käytännössä erittäin hankalaksi. Pääasiassa tämä johtuu höyrystimen rakenteesta sekä mittausmenetelmien korkeista kustannuksista. Tämän vuoksi työssä tarkastellaan myös edellytyksiä aukko-osuuden mittaamiselle erillisessä höyrystintä mallintavassa koelaitteistossa. Mikäli aukko-osuutta haluttaisiin mitata erilliskoelaitteistossa, tulisi höyrystinmallin rakennetta, materiaaleja tai kiertoainetta muuttaa PWR PACTELin höyrystimeen verrattuna.

Modelling of hydrogen stratification and gas mixing in containment using the APROS code

Hydrogen stratification and atmosphere mixing is a very important phenomenon in nuclear reactor containments when severe accidents are studied and simulated. Hydrogen generation, distribution and accumulation in certain parts of containment may pose a great risk to pressure increase induced by hydrogen combustion, and thus, challenge the integrity of NPP containment. The accurate prediction of hydrogen distribution is important with respect to the safety design of a NPP. Modelling methods typically used for containment analyses include both lumped parameter and field codes. The lumped parameter method is universally used in the containment codes, because its versatility, flexibility and simplicity. The lumped parameter method allows fast, full-scale simulations, where different containment geometries with relevant engineering safety features can be modelled. Lumped parameter gas stratification and mixing modelling methods are presented and discussed in this master’s thesis. Experimental research is widely used in containment analyses. The HM-2 experiment related to hydrogen stratification and mixing conducted at the THAI facility in Germany is calculated with the APROS lump parameter containment package and the APROS 6-equation thermal hydraulic model. The main purpose was to study, whether the convection term included in the momentum conservation equation of the 6-equation modelling gives some remarkable advantages compared to the simplified lumped parameter approach. Finally, a simple containment test case (high steam release to a narrow steam generator room inside a large dry containment) was calculated with both APROS models. In this case, the aim was to determine the extreme containment conditions, where the effect of convection term was supposed to be possibly high. Calculation results showed that both the APROS containment and the 6-equation model could model the hydrogen stratification in the THAI test well, if the vertical nodalisation was dense enough. However, in more complicated cases, the numerical diffusion may distort the results. Calculation of light gas stratification could be probably improved by applying the second order discretisation scheme for the modelling of gas flows. If the gas flows are relatively high, the convection term of the momentum equation is necessary to model the pressure differences between the adjacent nodes reasonably.

VVER-440 Thermal Hydraulics as a Computer Code Validation Challenge

This thesis concentrates on the validation of a generic thermal hydraulic computer code TRACE under the challenges of the VVER-440 reactor type. The code capability to model the VVER-440 geometry and thermal hydraulic phenomena specific to this reactor design has been examined and demonstrated acceptable. The main challenge in VVER-440 thermal hydraulics appeared in the modelling of the horizontal steam generator. The major challenge here is not in the code physics or numerics but in the formulation of a representative nodalization structure. Another VVER-440 specialty, the hot leg loop seals, challenges the system codes functionally in general, but proved readily representable. Computer code models have to be validated against experiments to achieve confidence in code models. When new computer code is to be used for nuclear power plant safety analysis, it must first be validated against a large variety of different experiments. The validation process has to cover both the code itself and the code input. Uncertainties of different nature are identified in the different phases of the validation procedure and can even be quantified. This thesis presents a novel approach to the input model validation and uncertainty evaluation in the different stages of the computer code validation procedure. This thesis also demonstrates that in the safety analysis, there are inevitably significant uncertainties that are not statistically quantifiable; they need to be and can be addressed by other, less simplistic means, ultimately relying on the competence of the analysts and the capability of the community to support the experimental verification of analytical assumptions. This method completes essentially the commonly used uncertainty assessment methods, which are usually conducted using only statistical methods.

Luonnonkiertovirtauksen kääntyminen pystyhöyrystimen lämmönvaihtoputkissa

Diplomityössä tutkitaan virtauksen kääntymistä Lappeenrannan teknillisen yliopiston PWR PACTEL –koelaitteiston pystyhöyrystimen lämmönvaihtoputkissa käyttäen APROS–prosessisimulointiohjelmaa. Työn teoriaosassa esitellään pystyhöyrystimillä varustettuja koelaitteistoja, erityisesti PWR PACTEL ja sen höyrystin. Lisäksi esitellään virtauksen kääntymisestä tehtyjä havaintoja ja käsitellään kääntymistä teoreettisesta näkökulmasta. Simulointiosan alussa esitellään työssä käytetty APROS –prosessisimulointiohjelma, sekä sen avulla höyrystimestä luodut mallit. Työssä on tutkittu virtauksen käännöstapahtumaa simuloimalla useita eri transienttitilanteita pienillä primäärimassavirroilla. Simulaatiotapauksissa havaittiin virtauksen kääntyvän höyrystimen eripituisissa lämmönvaihtoputkissa, tilanteesta riippuen pääosin lyhimmissä tai toisiksi lyhimmissä lämmönvaihtoputkissa. Transienttien eri vaiheiden, ts. primäärimassavirran muutos- ja tasaantumisvaiheiden pituuden havaittiin vaikuttavan siihen, minkä pituisissa putkissa kääntyminen tapahtuu ja missä järjestyksessä.

Integrating testcase generator into Eclipse environment

Tämädiplomityö tutkii kuinka Eclipse -ympäristöä voidaan käyttää testitapausten generoinnissa. Eräs diplomityön pääaiheista on tutkia voidaanko olemassa olevilla Eclipsen komponenteilla parantaa symboolitietoutta, jotta testitapausten generointiin saataisiin lisää tietoa. Aluksi diplomityö antaa lyhyen katsauksen ohjelmistojentestaukseen, jotta lukija ymmärtää mitä ohjelmistotekniikan osa-aluetta diplomityö käsittelee. Tämän jälkeen kerrotaan lisää tietoa itse testitapausten generointiprosessista. Kun perusteet on käsitelty, tutustetaan lukija Eclipse -ympäristöön, mikä se on, mistä se koostuu ja mitä sillä voidaan tehdä. Tarkempaa tietoa kerrotaan Eclipsen komponenteista joita voidaan käyttää apuna testitapausten generoinnissa. Integrointi esimerkkinä diplomityössä esitellään valmiin testitapausgeneraattorin integrointi Eclipse -ympäristöön. Lopuksi Eclipse -pohjaista ratkaisua verrataan symboolitietouden sekä ajoajan kannalta aikaisempaan ratkaisuun. Diplomityön tuloksena syntyi prototyyppi jonka avulla todistettiin, että Eclipse - ympäristöön on mahdollista integroida testitapausgeneraattori ja että se voi lisätä symboolitietoutta. Tämätietouden lisäys kuitenkin lisäsi myös tarvittavaa ajoaikaa, joissakintapauksissa jopa merkittävästi. Samalla todettiin, että tällä hetkellä on menossa projekteja joiden tarkoituksena on parantaa käytettyjen Eclipse komponenttien suorituskykyä ja että tämä voi parantaa tuloksia tulevaisuudessa.

Höyrynkestävän eristerakenteen suunnittelu sähkökoneen staattoriin

Perinteiset sähkökoneen eristemateriaalit eivät kestä vesihöyryä. Vesihöyryä kestävä eristerakenne on tarpeen, kun tehdään hermeettinen turbogeneraattori, jossa vesihöyry virtaa ilmavälin läpi. Tällainen turbogeneraattori mahdollistaa teholtaan tavallista pienemmän biopolttoainevoimalan rakentamisen kustannustehokkaasti. Työssä tutkittiin erilaisia pyörölankakäämityn pienjännitekoneen eristemateriaaleja. Pienoismallikokein testattiin ne eristemateriaalit, joiden uskottiin kirjallisuustietojen perusteella selviytyvän vesihöyryssä. Myös perinteinen, polyesteriin pohjautuva eristerakenne testattiin. Kokeiden perusteella valittiin turbogeneraattorin staattoriin sopiva eristerakenne.

Direct-on-line axial flux permanent magnet synchronous generator static and dynamic performance

In distributed energy production, permanent magnet synchronous generators (PMSG) are often connected to the grid via frequency converters, such as voltage source line converters. The price of the converter may constitute a large part of the costs of a generating set. Some of the permanent magnet synchronous generators with converters and traditional separately excited synchronous generators couldbe replaced by direct-on-line (DOL) non-controlled PMSGs. Small directly networkconnected generators are likely to have large markets in the area of distributed electric energy generation. Typical prime movers could be windmills, watermills and internal combustion engines. DOL PMSGs could also be applied in island networks, such as ships and oil platforms. Also various back-up power generating systems could be carried out with DOL PMSGs. The benefits would be a lower priceof the generating set and the robustness and easy use of the system. The performance of DOL PMSGs is analyzed. The electricity distribution companies have regulations that constrain the design of the generators being connected to the grid. The general guidelines and recommendations are applied in the analysis. By analyzing the results produced by the simulation model for the permanent magnet machine, the guidelines for efficient damper winding parameters for DOL PMSGs are presented. The simulation model is used to simulate grid connections and load transients. The damper winding parameters are calculated by the finite element method (FEM) and determined from experimental measurements. Three-dimensional finite element analysis (3D FEA) is carried out. The results from the simulation model and 3D FEA are compared with practical measurements from two prototype axial flux permanent magnet generators provided with damper windings. The dimensioning of the damper winding parameters is case specific. The damper winding should be dimensioned based on the moment of inertia of the generating set. It is shown that the damper winding has optimal values to reach synchronous operation in the shortest period of time after transient operation. With optimal dimensioning, interferenceon the grid is minimized.

Ash Particle Erosion on Steam Boiler Convective Section

In this study, equations for the calculation of erosion wear caused by ash particles on convective heat exchanger tubes of steam boilers are presented. Anew, three-dimensional test arrangement was used in the testing of the erosion wear of convective heat exchanger tubes of steam boilers. When using the sleeve-method, three different tube materials and three tube constructions could be tested. New results were obtained from the analyses. The main mechanisms of erosionwear phenomena and erosion wear as a function of collision conditions and material properties have been studied. Properties of fossil fuels have also been presented. When burning solid fuels, such as pulverized coal and peat in steam boilers, most of the ash is entrained by the flue gas in the furnace. In bubbling andcirculating fluidized bed boilers, particle concentration in the flue gas is high because of bed material entrained in the flue gas. Hard particles, such as sharp edged quartz crystals, cause erosion wear when colliding on convective heat exchanger tubes and on the rear wall of the steam boiler. The most important ways to reduce erosion wear in steam boilers is to keep the velocity of the flue gas moderate and prevent channelling of the ash flow in a certain part of the cross section of the flue gas channel, especially near the back wall. One can do this by constructing the boiler with the following components. Screen plates can beused to make the velocity and ash flow distributions more even at the cross-section of the channel. Shield plates and plate type constructions in superheaters can also be used. Erosion testing was conducted with three types of tube constructions: a one tube row, an inline tube bank with six tube rows, and a staggered tube bank with six tube rows. Three flow velocities and two particle concentrations were used in the tests, which were carried out at room temperature. Three particle materials were used: quartz, coal ash and peat ash particles. Mass loss, diameter loss and wall thickness loss measurements of the test sleeves were taken. Erosion wear as a function of flow conditions, tube material and tube construction was analyzed by single-variable linear regression analysis. In developing the erosion wear calculation equations, multi-variable linear regression analysis was used. In the staggered tube bank, erosion wear had a maximum value in a tube row 2 and a local maximum in row 5. In rows 3, 4 and 6, the erosion rate was low. On the other hand, in the in-line tube bank the minimum erosion rate occurred in tube row 2 and in further rows the erosion had an increasing value, so that in a six row tube bank, the maximum value occurred in row 6.

Code Generator for Key Management Protocols - Design and Implementation

Key management has a fundamental role in secure communications. Designing and testing of key management protocols is tricky. These protocols must work flawlessly despite of any abuse. The main objective of this work was to design and implement a tool that helps to specify the protocol and makes it possible to test the protocol while it is still under development. This tool generates compile-ready java code from a key management protocol model. A modelling method for these protocols, which uses Unified Modeling Language (UML) was also developed. The protocol is modelled, exported as an XMI and read by the code generator tool. The code generator generates java code that is immediately executable with a test software after compilation.

Design of flywheel generator for a diesel hybrid working machine

The aim of this work is to design a flywheel generator for a diesel hybrid working machine. In this work we perform detailed design of a generator. Mobile machines are commonly used in industry: road building machines, three harvesting machines, boring machines, trucks and other equipment. These machines work with a hydraulic drive system. This system provides good service property and high technical level. Manufacturers of mobile machines tend to satisfy all requirements of customers and modernized drive system. In this work also a description of the frequency inverter is present. Power electronics system is one of the basic parts for structures perform in the project.

New design of the frame for a permanent magnet generator

This thesis introduces a search for a new design of the frame for a permanent magnet generator mounted at a windmill. The objective of this work is to offer new design ideas for the stator frame - new concepts for connecting stator core to stator frame in a generator. Desired aims of new design concepts are: simplification of the structure production; decrease of material use; use of standard components; light weight of construction and etc. Thesis contains several new possible designs for the stator frame structure. Also, it has a list of possible connection concepts, which can be used to join the stator to the frame. All new ideas are described and compared according to its match to the desired purposes of the work. New design concepts are modeled using modern software. The main part of the Thesis contains several approximate computer models of the current and new offered constructions, description of loads and stress in the current stator frame. It has evaluation of the most important stress and load characteristics. The final design is a result of all previous research. It has a description of a new frame structure and joining concept for it. This structure matched main aims of work, but it does not have detailed design with dimensions and check calculations of the frame and welds. Thesis gives representation about design search, evaluation and comparison of new concepts of generator structure. Also, it gives general representation of renewable energy technology, knowledge about windmill turbines and its contents.

Modeling of water/steam circulation in Circulating Fluidized Bed boiler

A distinctive design feature of steam boiler with natural circulation is the presence of the steam drum which plays a role of the separator of vapor from the flow of water-and-steam mixture coming into steam drum from the furnace tubes. Steam drum with unheated downcomer tubes, deducing from it, and riser (screen/furnace tubes) inside the furnace is a closed circulation loop in which movement of water (downcomer tubes) and water-and-steam mixture (riser tubes) is organized. The movement of the working fluid is appears due to occurrence of the natural pressure, determined by the difference in hydrostatic pressure and the mass of water and water-and-steam mixtures in downcomer and riser tubes and called the driving pressure of the natural circulation:

Estimation of existing cable systems in generator-busbar unit and choice the optimal solution for its modernization

The aim of this master’s thesis is to develop an algorithm to calculate the cable network for heat and power station CHGRES. This algorithm includes important aspect which has an influence on the cable network reliability. Moreover, according to developed algorithm, the optimal solution for modernization cable system from economical and technical point of view was obtained. The conditions of existing cable lines show that replacement is necessary. Otherwise, the fault situation would happen. In this case company would loss not only money but also its prestige. As a solution, XLPE single core cables are more profitable than other types of cable considered in this work. Moreover, it is presented the dependence of value of short circuit current on number of 10/110 kV transformers connected in parallel between main grid and considered 10 kV busbar and how it affects on final decision. Furthermore, the losses of company in power (capacity) market due to fault situation are presented. These losses are commensurable with investment to replace existing cable system.

Modeling of water/steam circulation in Circulating Fluidized Bed boiler

A distinctive design feature of steam boiler with natural circulation is the presence of the steam drum which plays a role of the separator of vapor from the flow of water-and-steam mixture coming into steam drum from the furnace tubes. Steam drum with unheated downcomer tubes, deducing from it, and riser (screen/furnace tubes) inside the furnace is a closed circulation loop in which movement of water (downcomer tubes) and water-and-steam mixture (riser tubes) is organized. The movement of the working fluid is appears due to occurrence of the natural pressure, determined by the difference in hydrostatic pressure and the mass of water and water-and-steam mixtures in downcomer and riser tubes and called the driving pressure of the natural circulation: S drive = H steam (ρ down + ρ mix) g where: ρ down - density of water in downcomer tubes; ρ mix - density of water in riser tubes; H steam - height of steam content section; g - acceleration of gravity. In steam boilers with natural circulation the circulation rate is usually between 10 and 30. Thus, consumption of water in the circulation circuit “circulation rate times” more than steam output of the boiler. There are two aspects of the design of natural water circulation loops. One is to ensure a sufficient mass flux of circulating water to avoid burnout of evaporator tubes. The other is to avoid tube wall temperature fluctuation and tube vibration due to oscillation of circulation velocity. The design criteria are therefore reduced, in principle, to those of critical heat flux, critical flow rate for burnout, and flow instability. In practical design, however, the circulation velocity and the void fraction at the evaporator tube outlet are used as the design criteria (Seikan I., et. al., 1999). This study has been made with assumption that the heat flux in the furnace of the boiler even all the time. The target of the study was to define the circulation rate of the boiler, thus average heat flux do not change it. I would like to acknowledge professionals from “Foster Wheeler” company for good and comfortable cooperation.

Doubly fed induction generator versus direct drive permanent magnet synchronous generator in wind power applications

The objective of this master's thesis is to compare two different generator systems for wind turbines. It is the doubly fed induction generator system with three stage gearbox and the direct drive permanent magnet generator system. The comparison of generator systems is based on annual energy production for a given wind climate. For comparison a 3 MW, 15 rpm wind turbine is used. Modelling of a turbine rotor, gearbox and converters were done. Design of two generators was done and their performance was examined.