Frequency-Domain and Wide-Pulse Time-Domain Measurements of Lanthanide Luminescence and Lanthanide-Based Resonance Energy Transfer

Resonance energy transfer (RET) is a non-radiative transfer of the excitation energy from the initially excited luminescent donor to an acceptor. The requirements for the resonance energy transfer are: i) the spectral overlap between the donor emission spectrum and the acceptor absorption spectrum, ii) the close proximity of the donor and the acceptor, and iii) the suitable relative orientations of the donor emission and the acceptor absorption transition dipoles. As a result of the RET process the donor luminescence intensity and the donor lifetime are decreased. If the acceptor is luminescent, a sensitized acceptor emission appears. The rate of RET depends strongly on the donor–acceptor distance (r) and is inversely proportional to r6. The distance dependence of RET is utilized in binding assays. The proximity requirement and the selective detection of the RET-modified emission signal allow homogeneous separation free assays. The term lanthanide-based RET is used when luminescent lanthanide compounds are used as donors. The long luminescence lifetimes, the large Stokes’ shifts and the intense, sharply-spiked emission spectra of the lanthanide donors offer advantages over the conventional organic donor molecules. Both the organic lanthanide chelates and the inorganic up-converting phosphor (UCP) particles have been used as donor labels in the RET based binding assays. In the present work lanthanide luminescence and lanthanide-based resonance energy transfer phenomena were studied. Luminescence lifetime measurements had an essential role in the research. Modular frequency-domain and time-domain luminometers were assembled and used successfully in the lifetime measurements. The frequency-domain luminometer operated in the low frequency domain ( 100 kHz) and utilized a novel dual-phase lock-in detection of the luminescence. One of the studied phenomena was the recently discovered non-overlapping fluorescence resonance energy transfer (nFRET). The studied properties were the distance and temperature dependences of nFRET. The distance dependence was found to deviate from the Förster theory and a clear temperature dependence was observed whereas conventional RET was completely independent of the temperature. Based on the experimental results two thermally activated mechanisms were proposed for the nFRET process. The work with the UCP particles involved the measurement of the luminescence properties of the UCP particles synthesized in our laboratory. The goal of the UCP particle research is to develop UCP donor labels for binding assays. In the present work the effect of the dopant concentrations and the core–shell structure on the total up-conversion luminescence intensity, the red–green emission ratio, and the luminescence lifetime was studied. Also the non-radiative nature of the energy transfer from the UCP particle donors to organic acceptors was demonstrated for the first time in aqueous environment and with a controlled donor–acceptor distance.

Coarse Global Visual Localization of a Mobile Robot

Localization, which is the ability of a mobile robot to estimate its position within its environment, is a key capability for autonomous operation of any mobile robot. This thesis presents a system for indoor coarse and global localization of a mobile robot based on visual information. The system is based on image matching and uses SIFT features as natural landmarks. Features extracted from training images arestored in a database for use in localization later. During localization an image of the scene is captured using the on-board camera of the robot, features are extracted from the image and the best match is searched from the database. Feature matching is done using the k-d tree algorithm. Experimental results showed that localization accuracy increases with the number of training features used in the training database, while, on the other hand, increasing number of features tended to have a negative impact on the computational time. For some parts of the environment the error rate was relatively high due to a strong correlation of features taken from those places across the environment.

Business competence and training needs in Finnish companies operating in the Leningrad Region

Tässä pro gradu -työssä tutkitaan Leningradin alueella, Venäjällä, toimivien suomalaisyritysten liiketoimintaosaamisen koulutustarpeita. Tavoitteena on ollut tutkia, millaisia yritysten koulutustarpeet ovat, sekä lisäksi selvittää yleisemmällä tasolla, miten liiketoimintaosaaminen määritellään. Useat tutkimusta varten haastatellut johtajat pitävät liiketoimintaosaamista erityisesti markkinoilla toimimiseen liittyvänä osaamisena. Myös johtaminen, sekä tuotteet ja teknologia nähdään liiketoimintaosaamisen tärkeinä osina. Yrityksillä on koulutustarpeita seuraavilla alueilla: johtaminen; myynti, markkinat ja asiakkaat; yrityksen sisäinen yhteistyö; kielet, sekä juridiikka ja laskentatoimi. Haastateltavien mukaan markkinoiden nopea kehitys sekä yrityksen kasvu luovat yrityksille koulutustarpeita. Yllättäen myös Venäjän koulutusjärjestelmää itsessään pidetään koulutustarpeiden syynä. Tutkimuksessa mukana olleiden yritysten koulutuskäytännöt ovat keskenään melko erilaisia: koulutusbudjetti, koulutuspäivien määrä ja koulutusorganisaation valintakriteerit vaihtelevatyrityksestä riippuen. Joka tapauksessa yleisin koulutusmuoto näyttää olevan yrityksen sisäinen koulutus. Monet haastateltavat painottavat suuresti uusien työntekijöiden kouluttamista. Selvästikin rekrytointi ja uusien työntekijöiden koulutus vievät suuren osan tutkimusta varten haastateltujen johtajien ajasta. Tärkeä huomio koulutusmarkkinoihin liittyen on se, että lyhyiden, kaikille avoimien koulutusten kohdalla markkinat ovat Pietarissa täynnä. Suurimpana uhkana nähdään alalla vallitseva kouluttajapula.

Reduction of Greenhouse Gas Emissions in North-West Russia - Finnish Business Opportunities

Tutkimus suomalaisten yritysten liiketoimintamahdollisuuksista hiilidoksidipäästöjen vähentämisen parissa Luoteis-Venäjällä.

Dynamics of Appropriability - Finding a Balance between Efficiency and Strength in the Appropriability Regime

Building and sustaining competitive advantage through the creation of market imperfections is challenging in a constantly changing business environment - particularly since the sources of such advantages are increasingly knowledge-based. Facilitated by improved networks and communication, knowledge spills over to competitors more easily than before,thus creating an appropriability problem: the inability of an innovating firm to utilize its innovations commercially. Consequently, as the importance of intellectual assets increases, their protection also calls for new approaches. Companies have various means of protection at their disposal, and by taking advantage of them they can make intangibles more non-transferable and prevent, or at leastdelay, imitation of their most crucial intellectual assets. However, creating barriers against imitation has another side to it, and the transfer of knowledge in situations requiring knowledge sharing may be unintentionally obstructed. Theaim of this thesis is to increase understanding of how firms can balance knowledge protection and sharing so as to benefit most from their knowledge assets. Thus, knowledge protection is approached through an examination of the appropriability regime of a firm, i.e., the combination of available and effective means ofprotecting innovations, their profitability, and the increased rents due to R&D. A further aim is to provide a broader understanding of the formation and structure of the appropriability regime. The study consists of two parts. The first part introduces the research topic and the overall results of the study, and the second part consists of six complementary research publications covering various appropriability issues. The thesis contributes to the existing literature in several ways. Although there is a wide range of prior research on appropriability issues, a lot of it is restricted either to the study of individual appropriability mechanisms, or to comparing certain features of them. These approaches are combined, and the relevant theoretical concepts are clarified and developed. In addition, the thesis provides empirical evidence of the formation of the appropriability regime, which is consequently presented as an adaptive process. Thus, a framework is provided that better corresponds to the complex reality of the current business environment.

The effects of some variables on CO2 laser-MAG hybrid welding

The CO2-laser-MAG hybrid welding process has been shown to be a productive choice for the welding industry, being used in e.g. the shipbuilding, pipe and beam manufacturing, and automotive industries. It provides an opportunity to increase the productivity of welding of joints containing air gaps compared with autogenous laser beam welding, with associated reductions in distortion and marked increases in welding speeds and penetration in comparison with both arc and autogenous laser welding. The literature study indicated that the phenomena of laser hybrid welding are mostly being studied using bead-on-plate welding or zero air gap configurations. This study shows it very clearly that the CO2 laser-MAG hybrid welding process is completely different, when there is a groove with an air gap. As in case of industrial use it is excepted that welding is performed for non-zero grooves, this study is of great importance for industrial applications. The results of this study indicate that by using a 6 kW CO2 laser-MAG hybrid welding process, the welding speed may also be increased if an air gap is present in the joint. Experimental trials indicated that the welding speed may be increased by 30-82% when compared with bead-on-plate welding, or welding of a joint with no air gap i.e. a joint prepared as optimum for autogenous laser welding. This study demonstrates very clearly, that the separation of the different processes, as well as the relative configurations of the processes (arc leading or trailing) affect welding performance significantly. These matters influence the droplet size and therefore the metal transfer mode, which in turn determined the resulting weld quality and the ability to bridge air gaps. Welding in bead-onplate mode, or of an I butt joint containing no air gap joint is facilitated by using a leading torch. This is due to the preheating effect of the arc, which increases the absorptivity of the work piece to the laser beam, enabling greater penetration and the use of higher welding speeds. With an air gap present, air gap bridging is more effectively achieved by using a trailing torch because of the lower arc power needed, the wider arc, and the movement of droplets predominantly towards the joint edges. The experiments showed, that the mode of metal transfer has a marked effect on gap bridgeability. Transfer of a single droplet per arc pulse may not be desirable if an air gap is present, because most of the droplets are directed towards the middle of the joint where no base material is present. In such cases, undercut is observed. Pulsed globular and rotational metal transfer modes enable molten metal to also be transferred to the joint edges, and are therefore superior metal transfer modes when bridging air gaps. It was also found very obvious, that process separation is an important factor in gap bridgeability. If process separation is too large, the resulting weld often exhibits sagging, or no weld may be formed at all as a result of the reduced interaction between the component processes. In contrast, if the processes are too close to one another, the processing region contains excess molten metal that may create difficulties for the keyhole to remain open. When the distance is optimised - i.e. a separation of 0-4 mm in this study, depending on the welding speed and beam-arc configuration - the processes act together, creating beneficial synergistic effects. The optimum process separation when using a trailing torch was found to be shorter (0-2 mm) than when a leading torch is used (2-4 mm); a result of the facilitation of weld pool motion when the latter configuration is adopted. This study demonstrates, that the MAG process used has a strong effect on the CO2-laser-MAG hybrid welding process. The laser beam welding component is relatively stable and easy to manage, with only two principal processing parameters (power and welding speed) needing to be adjusted. In contrast, the MAG process has a large number of processing parameters to optimise, all of which play an important role in the interaction between the laser beam and the arc. The parameters used for traditional MAG welding are often not optimal in achieving the most appropriate mode of metal transfer, and weld quality in laser hybrid welding, and must be optimised if the full range of benefits provided by hybrid welding are to be realised.

Evaluation of Teacher Education Programs by Students and Graduates

The purpose of this research was to do a repeated cross-sectional research on class teachers who study in the 4th year and also graduated at the Faculty of Education, University of Turku between the years of 2000 through 2004. Specifically, seven research questions were addressed to target the main purpose of the study: How do class teacher education masters’ degree senior students and graduates rate “importance; effectiveness; and quality” of training they have received at the Faculty of Education? Are there significant differences between overall ratings of importance; effectiveness and quality of training by year of graduation, sex, and age (for graduates) and sex and age (for senior students)? Is there significant relationship between respondents’ overall ratings of importance; effectiveness and their overall ratings of the quality of training and preparation they have received? Are there significant differences between graduates and senior students about importance, effectiveness, and quality of teacher education programs? And what do teachers’ [Graduates] believe about how increasing work experience has changed their opinions of their preservice training? Moreover the following concepts related to the instructional activities were studied: critical thinking skills, communication skills, attention to ethics, curriculum and instruction (planning), role of teacher and teaching knowledge, assessment skills, attention to continuous professional development, subject matters knowledge, knowledge of learning environment, and using educational technology. Researcher also tried to find influence of some moderator variables e.g. year of graduation, sex, and age on the dependent and independent variables. This study consisted of two questionnaires (a structured likert-scale and an open ended questionnaire). The population in study 1 was all senior students and 2000-2004 class teacher education masters’ degree from the departments of Teacher Education Faculty of Education at University of Turku. Of the 1020 students and graduates the researcher was able to find current addresses of 675 of the subjects and of the 675 graduates contacted, 439 or 66.2 percent responded to the survey. The population in study 2 was all class teachers who graduated from Turku University and now work in the few basic schools (59 Schools) in South- West Finland. 257 teachers answered to the open ended web-based questions. SPSS was used to produce standard deviations; Analysis of Variance; Pearson Product Moment Correlation (r); T-test; ANOVA, Bonferroni post-hoc test; and Polynomial Contrast tests meant to analyze linear trend. An alpha level of .05 was used to determine statistical significance. The results of the study showed that: A majority of the respondents (graduates and students) rated the overall importance, effectiveness and quality of the teacher education programs as important, effective and good. Generally speaking there were only a few significant differences between the cohorts and groups related to the background variables (gender, age). The different cohorts were rating the quality of the programs very similarly but some differences between the cohorts were found in the importance and effectiveness ratings. Graduates of 2001 and 2002 rated the importance of the program significantly higher than 2000 graduates. The effectiveness of the programs was rated significantly higher by 2001 and 2003 graduates than other groups. In spite of these individual differences between cohorts there were no linear trends among the year cohorts in any measure. In respondents’ ratings of the effectiveness of teacher education programs there was significant difference between males and females; females rated it higher than males. There were no significant differences between males’ and females’ ratings of the importance and quality of programs. In the ratings there was only one difference between age groups. Older graduates (35 years or older) rated the importance of the teacher training significantly higher that 25-35 years old graduates. In graduates’ ratings there were positive but relatively low correlations between all variables related to importance, effectiveness and quality of Teacher Education Programs. Generally speaking students’ ratings about importance, effectiveness and quality of teacher education program were very positive. There was only one significant difference related to the background variables. Females rated higher the effectiveness of the program. The comparison of students’ and graduates’ perception about importance, effectiveness, and quality of teacher education programs showed that there were no significant differences between graduates and students in the overall ratings. However there were differences in some individual variables. Students rated higher in importance of “Continuous Professional Development”, effectiveness of “Critical Thinking Skills” and “Using Educational Technology” and quality of “Advice received from the advisor”. Graduates rated higher in importance of “Knowledge of Learning Environment” and effectiveness of “Continuous Professional Development”. According to the qualitative data of study 2 some graduates expressed that their perceptions have not changed about the importance, effectiveness, and quality of training that they received during their study time. They pointed out that teacher education programs have provided them the basic theoretical/formal knowledge and some training of practical routines. However, a majority of the teachers seems to have somewhat critical opinions about the teacher education. These teachers were not satisfied with teacher education programs because they argued that the programs failed to meet their practical demands in different everyday situations of the classroom e.g. in coping with students’ learning difficulties, multiprofessional communication with parents and other professional groups (psychologists and social workers), and classroom management problems. Participants also emphasized more practice oriented knowledge of subject matter, evaluation methods and teachers’ rights and responsibilities. Therefore, they (54.1% of participants) suggested that teacher education departments should provide more practice-based courses and programs as well as closer collaboration between regular schools and teacher education departments in order to fill gap between theory and practice.

Quality management of outsourcing welded structure: case China

For any international companies who wish to enter the Chinese market, quality is base on the fundamental. The companies are coming to realize the importance of quality gradually, thus companies have been put the quality problems on the agenda. The competitiveness of companies comes from quality. Quality is the key to success, and it can decide that the companies can be accepted or eliminated by the market. Due to the obvious benefits, the demand of the method of how to achieve high quality of product keeps growing. During achieving the high quality process, the main troubles come from the impact between Eastern and Western culture. Chinese culture which is different with Western one have lasted as long as five thousand years. Such a culture deeply rooted in the hearts of Chinese people, and effected generation after generation of Chinese people's working style and ways of thinking. This thesis determines how to find a good fit point between Eastern and Western culture. Doing right thing by the right way. The nature of improving quality is improving management level in fact. "How to manage, who should be managed", the thesis explains the basic and best option to achieve those. It describes three-dimension-style management to monitoring the working process. This kind of management style can inspect production process from horizontal and vertical direction. In this management way, it defines effective evaluation system to every subcontractor, and makes the companies to achieve the ultimate goal - satisfy quality. Because of the importance of human factor, the thesis determines the range of training of the inspector and welder due to the current situation of China. The results show that in order to reach reliable training effective evaluation, not only the quality of the human but also the ultimate goal of product quality.

Knowledge Sharing between Generations in an Organisation - Retention of the Old or Building the New?

The study explores knowledge transfer between retiring employees and their successors in expert work. My aim is to ascertain whether there is knowledge development or building new knowledge related to this organisational knowledge transfer between generations; in other words, is the transfer of knowledge from experienced, retiring employees to their successors merely retention of the existing organisational knowledge by distributing it from one individual to another or does this transfer lead to building new and meaningful organisational knowledge. I call knowledge transfer between generations and the possibly related knowledge building in this study knowledge sharing between generations. The study examines the organisation and knowledge management from a knowledge-based and constructionist view. From this standpoint, I see knowledge transfer as an interactive process, and the exploration is based on how the people involved in this process understand and experience the phenomenon studied. The research method is organisational ethnography. I conducted the analysis of data using thematic analysis and the articulation method, which has not been used before in organisational knowledge studies. The primary empirical data consists of theme interviews with twelve employees involved in knowledge transfer in the organisation being studied and five follow-up theme interviews. Six of the interviewees are expert duty employees due to retire shortly, and six are their successors. All those participating in the follow-up interviews are successors of those soon to retire from their expert responsibilities. The organisation in the study is a medium-sized Finnish firm, which designs and manufactures electrical equipment and systems for the global market. The results of the study show that expert work-related knowledge transfer between generations can mean knowledge building which produces new, meaningful knowledge for the organisation. This knowledge is distributed in the organisation to all those that find it useful in increasing the efficiency and competitiveness of the whole organisation. The transfer and building of knowledge together create an act of knowledge sharing between generations where the building of knowledge presupposes transfer. Knowledge sharing proceeds between the expert and the novice through eight phases. During the phases of knowledge transfer the expert guides the novice to absorb the knowledge to be transferred. With the expert’s help the novice gradually comes to understand the knowledge and in the end he or she is capable of using it in his or her work. During the phases of knowledge building the expert helps the novice to further develop the knowledge being transferred so that it becomes new, useful knowledge for the organisation. After that the novice takes the built knowledge to use in his or her work. Based on the results of the study, knowledge sharing between generations takes place in interaction and ends when knowledge is taken to use. The results I obtained in the interviews by the articulation method show that knowledge sharing between generations is shaped by the novices’ conceptions of their own work goals, knowledge needs and duties. These are not only based on the official definition of the work, but also how the novices find their work or how they prioritise the given objectives and responsibilities. The study shows that the novices see their work primarily as maintenance or development. Those primarily involved in maintenance duties do not necessarily need knowledge defined as transferred between generations. Therefore, they do not necessarily transfer knowledge with their assigned experts, even though this can happen in favourable circumstances. They do not build knowledge because their view of their work goals and duties does not require the building of new knowledge. Those primarily involved in development duties, however, do need knowledge available from their assigned experts. Therefore, regardless of circumstances they transfer knowledge with their assigned experts and also build knowledge because their work goals and duties create a basis for building new knowledge. The literature on knowledge transfer between generations has focused on describing either the knowledge being transferred or the means by which it is transferred. Based on the results of this study, however, knowledge sharing between generations, that is, transfer and building is determined by how the novice considers his or her own knowledge needs and work practices. This is why studies on knowledge sharing between generations and its implementation should be based not only on the knowledge content and how it is shared, but also on the context of the work in which the novice interprets and shares knowledge. The existing literature has not considered the possibility that knowledge transfer between generations may mean building knowledge. The results of this study, however, show that this is possible. In knowledge building, the expert’s existing organisational knowledge is combined with the new knowledge that the novice brings to the organisation. In their interaction this combination of the expert’s “old” and the novice’s “new” knowledge becomes new, meaningful organisational knowledge. Previous studies show that knowledge development between the members of an organisation is the prerequisite for organisational renewal which in turn is essential for improved competitiveness. Against this background, knowledge building enables organisational renewal and thus enhances competitiveness. Hence, when knowledge transfer between generations is followed by knowledge building, the organisation kills two birds with one stone. In knowledge transfer the organisation retains the existing knowledge and thus maintains its competitiveness. In knowledge building the organisation developsnew knowledge and thus improves its competitiveness.

The Process of Greening Cycle as Method of Operative Environmental

The structural change of society from product-based business to service- and further to need-based business has caused the fact that work for environmental issues has spread from conventional factories and environmentally harmful production to concern services and offices as well. Almost every company has an office, so a relatively small environmental burden caused by an individual office grows remarkable already at the state level and globally even more. Motivation to work for environmental issues in an individual office could be challenging even without the fact that wasted environmental impacts bound also wasted costs. Besides cost savings, a concretely greener image of a company has its value in the B2Cas well as in the B2B-field. Consumers and clients are more and more conscious of environmental issues and demand concrete actions instead of speeches, good thoughts and meaningless certifications. Internal work for environmental issues at a strategy level is not sufficient, so operational environmental management is needed for changing old practices. This research is about the effects of operative environmental management on the greening process of an office-based business. The research is outlined to concern the operative work in the office including field sales. Target was to concretely lower the environmental impacts of Lyreco Finland and to find cost savings directly by changing the operative practices in the office and also indirectly by affecting the level of environmental knowledge of the personnel. During the greening process, the aim was also to create concrete arguments for marketing as well. The circle of greening process, which was especially created for this diploma work, was used as a method. The circle divides a year to themes and sections separated by factors of environmental impacts. Separation is based on Brett Wills’ thoughts of seven green wastes (Wills, Brett. The Green Intensions. 2009) and follows it uneasily. The circle aimed at ensuring evolutionary growth of knowledge instead of being revolutionary in the changing process. Committing personnel to the process from its start by asking ideas from them and giving them clear directions was an important part of the research of operative management. Because of working from distance, communication with personnel was operated by frequent training days and weekly greening notes via emails and intranet. Also availability for communication was an important task because of the telecommuting. Research results of this work show that operative environmental management in an officebased business today is mostly management of change. When the strategic environmental friendliness is taken into a concrete level, the most important individual factor is motivating the operating personnel. Research shows that evolutionary change is found being an efficient way to make a change. Also understanding one´s own impact on the environmental burden and on the whole greening process clearly motivates the personnel. Results show that in the operative realization of the greening process, clear directions of new working practices, being as concrete as possible, and committing personnel to follow them make the process more effective. The operative environmental management and the cycle of the greening process decrease the environmental burden and save costs. The concrete results could be used as believable arguments in marketing and therefore exploited in communication with interest groups. Commitment of the management is also one of the key factors of success in the greening process. In this research, changes in the business field by a company trade took the focus of the management away from the greening process and made the process more inefficient by decreasing the amount of training days. The circle of greening process will be used as a tool in the future, as well, and therefore it will help observe environmental impacts of a company and increase sustainable development. Commitment of management to the evolutionary environmental work helps the operating personnel lower environmental impacts, decrease costs and build a concretely greener image.

Design Aspects of Megawatt-Range Direct-Driven Permanent MagnetWind Generators

Direct-driven permanent magnet synchronous generator is one of the most promising topologies for megawatt-range wind power applications. The rotational speed of the direct-driven generator is very low compared with the traditional electrical machines. The low rotational speed requires high torque to produce megawatt-range power. The special features of the direct-driven generators caused by the low speed and high torque are discussed in this doctoral thesis. Low speed and high torque set high demands on the torque quality. The cogging torque and the load torque ripple must be as low as possible to prevent mechanical failures. In this doctoral thesis, various methods to improve the torque quality are compared with each other. The rotor surface shaping, magnet skew, magnet shaping, and the asymmetrical placement of magnets and stator slots are studied not only by means of torque quality, but also the effects on the electromagnetic performance and manufacturability of the machine are discussed. The heat transfer of the direct-driven generator must be designed to handle the copper losses of the stator winding carrying high current density and to keep the temperature of the magnets low enough. The cooling system of the direct-driven generator applying the doubly radial air cooling with numerous radial cooling ducts was modeled with a lumped-parameter-based thermal network. The performance of the cooling system was discussed during the steady and transient states. The effect of the number and width of radial cooling ducts was explored. The large number of radial cooling ducts drastically increases the impact of the stack end area effects, because the stator stack consists of numerous substacks. The effects of the radial cooling ducts on the effective axial length of the machine were studied by analyzing the crosssection of the machine in the axial direction. The method to compensate the magnet end area leakage was considered. The effect of the cooling ducts and the stack end area effects on the no-load voltages and inductances of the machine were explored by using numerical analysis tools based on the three-dimensional finite element method. The electrical efficiency of the permanent magnet machine with different control methods was estimated analytically over the whole speed and torque range. The electrical efficiencies achieved with the most common control methods were compared with each other. The stator voltage increase caused by the armature reaction was analyzed. The effect of inductance saturation as a function of load current was implemented to the analytical efficiency calculation.

Intra-organizational knowledge transfer in a Finnish multinational company

The ability of a multinational company to effectively transfer knowledge from one unit to another can create a great source of competitive advantage and is crucial for long-term success. However, in their attempts to disseminate existent knowledge across national boundaries, organizations encounter several obstacles. Especially challenging is the transfer of tacit knowledge, the most valuable kind, as it is embedded in the minds and the behavior of people. The purpose of this study is to identify the main factors and challenges to be considered in intra-organizational knowledge transfer and consequently develop a framework that could be utilized to improve the process. The research is of qualitative nature and it adopts an exploratory approach. The study was further conducted as an intensive single-case study through studying a Finnish multinational company, and the researcher adopted a role as a participant observant in the research setting. Other data collection methods include semi-structured interviews and an online survey. The research findings show that knowledge transfer is currently challenging within the international sales organization of the case company. The majority of knowledge is currently concentrated in the company headquarters, and it is not always systematically distributed to the regional offices abroad. The main factor affecting knowledge transfer seems to be the organizational culture, which does not support or encourage knowledge sharing. The company is struggling in having a common place for information and employees that lack proper social networks have difficulties accessing relevant knowledge. Some recommended improvement suggestions include the institutionalization of knowledge transfer by turning it into an articulated organizational goal, and the implementation of a reward system that includes soft factors, such as teamwork and knowledge sharing behavior. Furthermore, the organizational culture should be more open and supportive in order to reinforce trust. Individuals in regional offices should be given better support by offering them dedicated mentors and increasing the amount of expatriation. Finally, knowledge should actively be codified and stored in commonly shared platforms where it is easily accessible by all employees.

Recovery of carboxylic acids from aqueous streams by extraction and back extraction

Separation of carboxylic acids from aqueous streams is an important part of their manufacturing process. The aqueous solutions are usually dilute containing less than 10 % acids. Separation by distillation is difficult as the boiling points of acids are only marginally higher than that of water. Because of this distillation is not only difficult but also expensive due to the evaporation of large amounts of water. Carboxylic acids have traditionally been precipitated as calcium salts. The yields of these processes are usually relatively low and the chemical costs high. Especially the decomposition of calcium salts with sulfuric acid produces large amounts of calcium sulfate sludge. Solvent extraction has been studied as an alternative method for recovery of carboxylic acids. Solvent extraction is based on mixing of two immiscible liquids and the transfer of the wanted components form one liquid to another due to equilibrium difference. In the case of carboxylic acids, the acids are transferred from aqueous phase to organic solvent due to physical and chemical interactions. The acids and the extractant form complexes which are soluble in the organic phase. The extraction efficiency is affected by many factors, for instance initial acid concentration, type and concentration of the extractant, pH, temperature and extraction time. In this paper, the effects of initial acid concentration, type of extractant and temperature on extraction efficiency were studied. As carboxylic acids are usually the products of the processes, they are wanted to be recovered. Hence the acids have to be removed from the organic phase after the extraction. The removal of acids from the organic phase also regenerates the extractant which can be then recycled in the process. The regeneration of the extractant was studied by back-extracting i.e. stripping the acids form the organic solution into diluent sodium hydroxide solution. In the solvent regeneration, the regenerability of different extractants and the effect of initial acid concentration and temperature were studied.

Hiljaisen tiedon siirtämisen prosessi mentoroinnissa – näkökulmana kognitiivinen oppipoikamalli

Hiljainen tieto muodostaa organisaatioiden keskeisen kilpailutekijän, sillä sitä on vaikea kopioida. Hiljaista tietoa pyritään siirtämään erilaisia osaamisen kehittämisen menetelmiä hyödyntäen. Tässä tutkielmassa tutkitaan, miten hiljaista tietoa siirretään mentoroinnissa. Mentorointiin liittyvissä tutkimuksissa ei ole tutkittu sitä vuorovaikutukseen perustuvaa prosessia, jonka aikana hiljaista tietoa siirretään mentorilta aktorille. Tämä tutkielma toi lisää tietoa tähän tutkimusaukkoon. Tutkielman teoreettisessa osiossa esiteltiin kolme näkökulmaa, jotka muo-dostivat tutkielman viitekehyksen: hiljainen tieto ja sen siirtäminen, mentorointi sekä kognitiivinen oppipoikamalli. Tutkimusmenetelmänä käytettiin fenomenografista tapaustutkimusta. Tutkimuksen kohderyhmän muodostivat neljä mentori-aktori –paria, joita haastateltiin teemahaastattelulla. Empiiriset tulokset osoittivat, että hiljaisen tiedon siirtäminen mentoroinnissa tapahtui kognitiivisen oppipoikamallin vaiheita hyödyntäen. Kaikki kognitiivisen oppipoikamallin vaiheet esiintyivät mentorointiprosessissa. Siirrettävässä hiljaisessa tiedossa näyttäytyivät tiedon toiminnallinen, situationaalinen ja sosiaalinen luonne. Keskeisimmiksi hiljaisen tiedon siirtämisen menetelmiksi osoittautuivat mentorin läsnäolo, kuuntelu, kysymysten tekeminen ja aktorin oivalluttaminen. Tutkielman keskeisenä tuloksena ja toimenpide-ehdotuksena esitettiin hiljaisen tiedon siirtämisen malli mentoroinnissa, joka kehitettiin tutkimuksen teoreettisen viitekehyksen ja tutkimuksesta saatujen tulosten pohjalta.

Two-dimensional atom localization and Raman cooling of tripod-type atoms

Both atom localization and Raman cooling, considered in the thesis, reflect recent progress in the area of all-optical methods. We focus on twodimensional (2D) case, using a four-level tripod-type atomic scheme for atom localization within the optical half-wavelength as well as for efficient subrecoil Raman cooling. In the first part, we discuss the principles of 1D atom localization, accompanying by an example of the measurement of a spontaneously-emitted photon. Modifying this example, one archives sub-wavelength localization of a three-level -type atom, measuring the population in its upper state. We go further and obtain 2D sub-wavelength localization for a four-level tripod-type atom. The upper-state population is classified according to the spatial distribution, which in turn forms such structures as spikes, craters and waves. The second part of the thesis is devoted to Raman cooling. The cooling process is controlled by a sequence of velocity-selective transfers from one to another ground state. So far, 1D deep subrecoil cooling has been carried out with the sequence of square or Blackman pulses, applied to -type atoms. In turn, we discuss the transfer of atoms by stimulated Raman adiabatic passage (STIRAP), which provides robustness against the pulse duration if the cooling time is not in any critical role. A tripod-type atomic scheme is used for the purpose of 2D Raman cooling, allowing one to increase the efficiency and simplify the realization of the cooling.