Utilization of a Time Domain Simulator in the Technical and Economic Analysis of a Wind Turbine Electric Drive Train

The amount of installed wind power has been growing exponentially during the past ten years. As wind turbines have become a significant source of electrical energy, the interactions between the turbines and the electric power network need to be studied more thoroughly than before. Especially, the behavior of the turbines in fault situations is of prime importance; simply disconnecting all wind turbines from the network during a voltage drop is no longer acceptable, since this would contribute to a total network collapse. These requirements have been a contributor to the increased role of simulations in the study and design of the electric drive train of a wind turbine. When planning a wind power investment, the selection of the site and the turbine are crucial for the economic feasibility of the installation. Economic feasibility, on the other hand, is the factor that determines whether or not investment in wind power will continue, contributing to green electricity production and reduction of emissions. In the selection of the installation site and the turbine (siting and site matching), the properties of the electric drive train of the planned turbine have so far been generally not been taken into account. Additionally, although the loss minimization of some of the individual components of the drive train has been studied, the drive train as a whole has received less attention. Furthermore, as a wind turbine will typically operate at a power level lower than the nominal most of the time, efficiency analysis in the nominal operating point is not sufficient. This doctoral dissertation attempts to combine the two aforementioned areas of interest by studying the applicability of time domain simulations in the analysis of the economicfeasibility of a wind turbine. The utilization of a general-purpose time domain simulator, otherwise applied to the study of network interactions and control systems, in the economic analysis of the wind energy conversion system is studied. The main benefits of the simulation-based method over traditional methods based on analytic calculation of losses include the ability to reuse and recombine existing models, the ability to analyze interactions between the components and subsystems in the electric drive train (something which is impossible when considering different subsystems as independent blocks, as is commonly done in theanalytical calculation of efficiencies), the ability to analyze in a rather straightforward manner the effect of selections other than physical components, for example control algorithms, and the ability to verify assumptions of the effects of a particular design change on the efficiency of the whole system. Based on the work, it can be concluded that differences between two configurations can be seen in the economic performance with only minor modifications to the simulation models used in the network interaction and control method study. This eliminates the need ofdeveloping analytic expressions for losses and enables the study of the system as a whole instead of modeling it as series connection of independent blocks with no lossinterdependencies. Three example cases (site matching, component selection, control principle selection) are provided to illustrate the usage of the approach and analyze its performance.

Utilization of Incident Reporting in The Finnish Maritime Industry

Marine traffic is expected to increase rapidly in the future, both in the Baltic Sea and in the Gulf of Finland. As the number of vessels in the area increases, so does the risk of serious marine accidents. To help prevent such accidents in the future, the International Maritime Organization (IMO) has put forth the International Safety Management Code (the ISM Code), which aims to improve the safety of the vessels. The second work package of the Development of maritime safety culture (METKU) project investigates the effects of the ISM Code and potential areas of improvement in maritime safety. The first phase in the work package used a literature review to determine how maritime safety culture could be improved. Continuous improvement, management commitment and personnel empowerment and motivation were found to be essential. In the second phase, shipping companies and administrators were interviewed. It was discovered that especially incident reporting based on continuous improvement was felt to be lacking. This third phase aims to take a closer look at incident reporting and suggest improvements based on the findings. Both the IMO and national legislation encourage shipping companies in incident reporting, and on the national level a shared incident reporting system (ForeSea) is being pushed forward. The objective of this research project was to find out the IMO’s attitude towards incident reporting, to establish a theoretical framework of reference in incident reporting, and to observe how reporting is actually being employed on the seas. Existing incident reporting systems were also researched. The study was carried out using a literature review and the results previously gathered in interviews. The results of phase two were elaborated further for themes relating to incident reporting. According to the findings of this research, the theoretical background of incident reporting dates back to the early 20th century. Although some theories are widely accepted, some have also received criticism. The lack of a concise, shared terminology poses major difficulties in maritime incident reporting and in determining its efficiency. A central finding is the fact that existing incident reporting focuses mostly on information flow away from the ship, whereas the backward information flow is much less planned and monitored. In incident reporting, both nationally and internationally, stakeholders are plenty. The information produced by these parties is scattered, however, and thus not very usable. Based on this research, the centralizing of this information should be made a priority. Traditionally, the success of incident reporting has been determined statistically, from the number of reported incidents. Yet existing reporting systems have not been designed with such statistical analysis in mind, so different methodologies might yield a more comprehensive view. The previous findings of seafarers and management (including shipping companies and administration) having differing views on safety work and safety management were backed up by the results of this study. Seafarers find seamanship and storytelling important, while management wants a more systematic and broad approach on safety matters. The research project was carried out by the Centre for Maritime Studies of the University of Turku, in the Kotka unit (Maritime Logistics Research), with coordination by the Kotka Maritime Research Centre. The major financiers of the project were the European Union and the city of Kotka. The financing authority was the Regional Council of Päijät-Häme. Partners in the project were the shipping companies Finnlines Oyj, Kristina Cruises Oy, Meriaura Oy and VG-Shipping Oy, and the ports of Helsinki, Kotka and Hamina. The partners provided both funding for the project and information for the research.

Utilization of Automatic Meter Reading in the Improvement of a District Heating System

A district heating system comprises production facilities, a distribution network, and heat consumers. The utilization of new energy metering and reading system (AMR) is increasing constantly in district heating systems. This heuristic study shows how the AMR system can be exploited in finding optimization opportunities in district heating system. In this study, the district heating system is mainly considered from the viewpoint of operational optimization. The focus is on the core processes, heat production and distribution. Three objectives were set to this study. The first one was to examine general optimization opportunities in district heating systems. Second, to figure out the benefits of AMR for general optimization opportunities. Finally, to define a methodology for process improvement endeavors. This study shows, through a case study, the usefulness of AMR in specifying current deficiencies in a district heating system. Based on a literature review, the methodology for the improvement of business processes is presented. Additionally, some issues related to future competitiveness of district heating are concerned. As a conclusion, some optimization objectives are considered more desirable than others. Study shows that AMR is useful in the specification of optimization targets in the district heating system. Further steps in optimization process were not examined in detail. That would seem to be interesting topic for further studies.

Utilization of Meat and bone meal for energy production

At the end of the 1990s the stock breeding in the Europe was suffering from the animal disease epidemics such as Bovine spongiform encephalopathy (BSE) and foot –and mouth disease. The European Union (EU) tackled to this problem by tightening the legislation of animal by-products. At this point, rendering and fat producing industries faces new challenges, which they have to cope with in a way of trying to find alternatives to their products (animal fats and meat and bone meal). One of the most promising alternatives to utilize these products was to use them in energy production purposes. The purpose of the Thesis was to examine the utilization possibilities of Meat and bone meal (MBM) for energy production. The first part of the Thesis consists of theory part. The theory part includes evaluation of basic properties of MBM as a fertilizer and as a fuel, legislative evaluation and evaluation of different burning techniques. The second part of the Thesis consists of burning tests in Energy laboratory of LUT with different mixtures of peat and MBM. The purpose of the burning tests was to identify co-firing possibilities of peat and MBM and emission- and ash properties for peat and MBM.

Customer reference marketing and utilization of social media as an integral part of customer references

The objective of this Bachelor's Thesis is to find out the role of social media in the B-to-B marketing environment of the information technology industry and to discover how IT-firms utilize social media as a part of their customer reference marketing. To reach the objectives the concepts of customer reference marketing and social media are determined. Customer reference marketing can be characterized as one of the most practically relevant but academically relatively overlooked ways in which a company can leverage its customers and delivered solutions and use them as references in its marketing activities. We will cover which external and internal functions customer references have, that contribute to the growth and performance of B-to-B firms. We also address the three mechanisms of customer reference marketing which are 'status transfer', 'validation through testimonials' and 'demonstration of experience and prior performance'. The concept of social media stands for social interaction and creation of user-based content which exclusively occurs through Internet. The social media are excellent tools for networking because of the fast and easy access, easy interaction and vast amount of multimedia attributes. The allocation of social media is determined. The case company helps clarify the specific characteristics of social media usage as part of customer-reference-marketing activities. For IT-firms the best channels to utilize social media in their customer reference marketing activities are publishing and distribution services of content and networking services.

Efficient installed base information management and utilization in global after sales service business

This Master´s thesis explores how the a global industrial corporation’s after sales service department should arrange its installed base management practices in order to maintain and utilize the installed base information effectively. Case company has product-related records, such as product’s lifecycle information, service history information and information about product’s performance. Information is collected and organized often case by case, therefore the systematic and effective use of installed base information is difficult also the overview of installed base is missing. The goal of the thesis study was to find out how the case company can improve the installed base maintenance and management practices and improve the installed base information availability and reliability. Installed base information management practices were first examined through the literature. The empirical research was conducted by the interviews and questionnaire survey, targeted to the case company’s service department. The research purpose was to find out the challenges related to case company´s service department’s information management practices. The study also identified the installed base information needs and improvement potential in the availability of information. Based on the empirical research findings, recommendations for improve installed base management practices and information availability were created. Grounding of the recommendations, the case company is suggested the following proposals for action: Service report development, improving the change management process, ensuring the quality of the product documentation in early stages of product life cycle and decision to improve installed base management practices.

Customer satisfaction data utilization: identifying value drivers and information use practices

The objective of this master’s thesis was twofold: first to examine the concept of customer value and its drivers and second to identify information use practices. The first part of the study represents explorative research that was carried out by examining a case company’s customer satisfaction data that was used to identify sales and technical customer service related value drivers on a detailed attribute level. This was followed by an examination of whether these attributes had been commented on in a positive or a negative light and what were the reasons why the case company had received higher or lower ratings than its competitor. As a result a classification of different sales and technical customer service related attributes was created. The results indicated that the case company has performed well, but that the results varied on the company’s business segment level. The case company’s staff, service and the benefits from a long-lasting relationship came up in a positive light whereas attitude, flexibility and reaction time came up in a negative light. The reasons for a higher or lower score in comparison to competitor varied. The results indicated that a customer’s satisfaction with the company’s performance did not always mean that the company was outperforming the competition. The second part of the study focused on customer satisfaction information use from the viewpoints of information access, dissemination and reaction. The study was conducted by running an internal survey among the case company’s staff. The results showed that information use practices varied across the company and some units or teams had taken a more proactive approach to the information use than others.

Utilization of non ferrous metals in boiler combustion environment

The made research is focused on possibility of application of non ferrous metals in boiler pressure parts as a substitute of currently used ferrous-base alloys. The main issue was to define resistive ability of some perspective non ferrous metals to chlorine induced corrosion. Experimental study was performed using simultaneous thermal analysis (STA) in the temperature range of 400-700 °C. The chloride induced corrosion was simulated by mixtures of metal samples with potassium chloride treated by synthetic air. The advantage of synergetic effect of non ferrous alloys compare to single metals is shown due to the obtained data from conducted thermal balance tests.

Measuring effects of strategic utilization of social media in business-to-business marketing: Case Greenlux Finland Oy

Utilization of social media is increasingly common in B2B marketing. Social media is an efficient and cheap marketing and communication channel available for everyone, and thus extremely attractive marketing medium. The more companies get involved in social media the more failures are reported. It is not enough for a company to just be present in social media. Succeeding on it requires hard work, investing time and money, and ability to measure and to monitor performance. With an increasing number of companies failing in utilizing social media, together with lack of research on strategic utilization of social media focusing on B2B marketing, measuring, and monitoring create a purpose for this research. The aim of this research is to discover methods for measuring and monitoring effects of strategic utilization of social media in B2B marketing. Most relevant financial and non-financial indicators are discussed, and the methods by which these can be monitored and measured. In addition, effects of strategic utilization of social media on the case company are measured and analyzed. The research methodology used in this research is a participatory action research, which includes elements of both qualitative and quantitative research methods. The case company examined in the research provides a unique opportunity to follow through all phases of strategic utilization of social media for B2B marketing purposes concluding real effects of social media to the case company, and thus gain a deep understanding about this new marketing medium in the perspective of B2B marketing. Duration of the research period is seven months. During this time, information is collected, measured, and analyzed. Case company does not have any other marketing activities simultaneously which makes it possible to examine social media apart from effects of other visible marketing activities. Effects of strategic utilization of social media can be monitored and measured in many ways. Methods that should be used depend on goals set for social media. Fundamental nature of social media requires multidimensional assessment, and thus effects should be measured, and monitored considering both financial and non-financial indicators. The results implicates that effects of strategic utilization of social media are relatively wide ranged. According to the findings, social media affects positively on brand, number of web page visitors, visitor behavior, and on distribution of awareness. According to investment calculations social media is a legitimate investment for case company. Results also implicate that by using social media case company gains conversation, arouses interest, gets attention, and creates interactivity. In addition and as a side note, winter holiday season appears to have a great effect on social media activity of B2B companies’ representatives.

Imaging of Tumour Microenvironment for the Planning of Oncological Therapies Using Positron Emission Tomography

Tumour cells differ from normal tissue cells in several important ways. These differences, like for example changed energy metabolism, result in altered microenvironment of malignant tumours. Non-invasive imaging of tumour microenvironment has been at the centre of intense research recently due to the important role that this changed environement plays in the development of malignant tumours and due to the role it plays in the treatment of these tumours. In this respect, perhaps the most important characteristics of the tumour microenvironment from this point of view are the lack of oxygen or hypoxia and changes in blood flow (BF). The purpose of this thesis was to investigate the processes of energy metabolism, BF and oxygenation in head and neck cancer and pancreatic tumours and to explore the possibilities of improving the methods for their quantification using positron emission tomography (PET). To this end [18F]EF5, a new PET tracer for detection of tumour hypoxia was investigated. Favourable uptake properties of the tracer were observed. In addition, it was established that the uptake of this tracer does not correlate with the uptake of existing tracers for the imaging of energy metabolism and BF, so the information about the presence of tissue hypoxia cannot therefore be obtained using tracers such as [18F]FDG or [15O]H2O. These results were complemented by the results of the follow-up study in which it was shown that the uptake of [18F]EF5 in head and neck tumours prior to treatment is also associated with the overall survival of the patients, indicating that tumour hypoxia is a negative prognostic factor and might be associated with therapeutic resistance. The influences of energy metabolism and BF on the survival of patients with pancreatic cancer were investigated in the second study. The results indicate that the best predictor of survival of patients with pancreatic cancer is the relationship between energy metabolism and BF. These results suggest that the cells with high metabolic activity in a hypoperfused tissue have the most aggressive phenotype.

Utilization of Particle Image velocimetry in PPOOLEX condensation experiments

Particle Image Velocimetry, PIV, is an optical measuring technique to obtain velocity information of a flow in interest. With PIV it is possible to achieve two or three dimensional velocity vector fields from a measurement area instead of a single point in a flow. Measured flow can be either in liquid or in gas form. PIV is nowadays widely applied to flow field studies. The need for PIV is to obtain validation data for Computational Fluid Dynamics calculation programs that has been used to model blow down experiments in PPOOLEX test facility in the Lappeenranta University of Technology. In this thesis PIV and its theoretical background are presented. All the subsystems that can be considered to be part of a PIV system are presented as well with detail. Emphasis is also put to the mathematics behind the image evaluation. The work also included selection and successful testing of a PIV system, as well as the planning of the installation to the PPOOLEX facility. Already in the preliminary testing PIV was found to be good addition to the measuring equipment for Nuclear Safety Research Unit of LUT. The installation to PPOOLEX facility was successful even though there were many restrictions considering it. All parts of the PIV system worked and they were found out to be appropriate for the planned use. Results and observations presented in this thesis are a good background to further PIV use.

The sources of complementary competitive advantages for systems’ manufacturers in the aircraft modernization market

Being a top of high technology industries, the aerospace represents one of the most complex fields of study. While the competitiveness of aircraft systems’ manufacturers attracts a significant number of researchers, some of the issues remain to be a blank spot. One of those is the after-sale modernization. The master thesis investigates how this concept is related to the theory of competitive advantages. Finding the routes in the framework of complex technological systems’ lifecycle, the key drivers of the aircraft modernization market are revealed. The competitive positioning of players is defined through multiple case studies in a form of several in-depth interviews. The key result of the research is the conclusion that modernization should be considered as an inherent component of strategy of any aircraft systems’ manufacturer, while the master thesis aims to support managerial decision making.

The effects of location, feedstock availability, and supply-chain logistics on the greenhouse gas emissions of forest-biomass energy utilization in Finland

Forest biomass represents a geographically distributed feedstock, and geographical location affects the greenhouse gas (GHG) performance of a given forest-bioenergy system in several ways. For example, biomass availability, forest operations, transportation possibilities and the distances involved, biomass end-use possibilities, fossil reference systems, and forest carbon balances all depend to some extent on location. The overall objective of this thesis was to assess the GHG emissions derived from supply and energy-utilization chains of forest biomass in Finland, with a specific focus on the effect of location in relation to forest biomass’s availability and the transportation possibilities. Biomass availability and transportation-network assessments were conducted through utilization of geographical information system methods, and the GHG emissions were assessed by means of lifecycle assessment. The thesis is based on four papers in which forest biomass supply on industrial scale was assessed. The feedstocks assessed in this thesis include harvesting residues, smalldiameter energy wood and stumps. The principal implication of the findings in this thesis is that in Finland, the location and availability of biomass in the proximity of a given energyutilization or energy-conversion plant is not a decisive factor in supply-chain GHG emissions or the possible GHG savings to be achieved with forest-biomass energy use. Therefore, for the greatest GHG reductions with limited forest-biomass resources, energy utilization of forest biomass in Finland should be directed to the locations where most GHG savings are achieved through replacement of fossil fuels. Furthermore, one should prioritize the types of forest biomass with the lowest direct supply-chain GHG emissions (e.g., from transport and comminution) and the lowest indirect ones (in particular, soil carbon-stock losses), regardless of location. In this respect, the best combination is to use harvesting residues in combined heat and power production, replacing peat or coal.