Kaksiakselisen välijäähdytyksellä, välipoltolla ja rekuperaattorilla varustetun mikrokaasuturbiinin osakuormahyötysuhteen säilyvyyden optimointi

Työssä pyrittiin etsimään differentiaalievoluutioalgoritmilla kaksiakseliselle, välijäähdytyksellä, välipoltolla ja rekuperaattorilla varustetulle mikrokaasuturbiinille sellaiset kompressorien painesuhteet ja rekuperaattorin rekuperaatioaste, että saavutettaisiin mandollisimman hyvä osakuormahyötysuhteen säilyvyys. Osakuormatehon säätömenetelmäksi oli valittu pyörimisnopeussäädön ja turbiinien sisääntulolämpötilan alentamisen yhdistelmä, jossa generaattorilla varustetun akselin pyörimisnopeus sekä molempien turbiinien sisääntulolämpötilat olivat toisistaan riippumatta vapaasti säädettävissä. Työssä löydettiin optimaalinen säätömenetelmien yhdistelmä, jolla saavutetaan parempi osakuormahyötysuhteen säilyvyys, kuin millään käytetyistä menetelmistä yksinään. Lisäksi havaittiin, ettei optimaalinen säätömenetelmä merkittävästi riipu koneikolle valituista suunnittelupisteen parametreista. Osakuormahyötysuhteen säilyvyyden kannalta optimaalinen koneikko ei merkittävästi poikennut suunnittelupisteen hyötysuhteen kannalta optimaalisesta.

Biopolttoaineilla toimiva Stirling-voimalaitos

Stirling-moottori on ns. kuumailma moottori, joka toimii kaasun lämpötilaeron avulla. Kuumailma moottorin erityispiirteitä on laitteen ulkopuolella tapahtuva palaminen, josta lämpö johdetaan moottorille. Yleensä polttoaineena on käytetty vähän likaavaa polttoainetta esim. maakaasua mutta fossiilisten polttoaineiden kallistumisen ja niistä aiheutuvien päästöjen vuoksi niiden korvaaminen biopolttoaineella on tullut ajankohtaiseksi aiheeksi. Biopolttoaineiden likaavuuden takia niillä ei kuitenkaan voida lämmittää Stirling-moottoria suoraan vaan tarvitaan ylimääräinen lämmönsiirrin. Tämä diplomityö suoritettiin Lappeenrannan teknilliselle yliopistolle ja sen tarkoituksena oli tutkia juuri tähän laitteistoon suunnitellun, Stirling-moottorin ja polttokammion välisen lämmönsiirtimen suoritusarvoja ja likaantumista. Lisäksi työssä tutkittiin lämmönsiirtimeltä Stirling-moottorille menevien ilmaputkien lämpöhäviöitä. Työssä tultiin siihen tulokseen, että tämän tyyppinen lämmönsiirrin on suoritusarvoiltaan keskiverto kaasu-kaasu lämmönsiirrintä parempi ja ei likaannu erityisen nopeasti. Lämpöhäviöt olivat toisaalta merkittävämmässä asemassa kuin likaantuminen. Suurista lämpötiloista johtuva eristeiden lämmöneristyskyvyn heikkeneminen tai lämmönsiirtimen vuoto aiheutti merkittäviä lämpöhäviöitä.

Kolmen vapausasteen akseliston ohjaaminen mikroprosessorilla

Diplomityön tavoitteena on tehdä lasertyöasemalle liikkuva kolmen vapausasteen akselisto liikuttamaan laser-laitteiston skanneripäätä. Liikkeen tarkkuus ja tarkka toistettavuus ovat tärkeitä. Moottoreiden liikkeen nopeus sekä kiihdytys- ja jarrutusparametrien täytyy olla määriteltävissä jokaiselle moottorille erikseen. Kolmen vapausasteen akselisto muodostetaan käyttäen kolmea askelmoottoria ja lineaarivaihteistoa. Akselisto liikkuu vaaka-, pysty-, ja syvyyssuunnassa. Työssä kehitetään C-kielinen ohjelma käytettävälle prosessorille ja suunnitellaan ohjainkortti lopullista prototyyppiä varten. Moottoreiden ohjaus ja hallinta toteutetaan AT91S256-prosessorilla, jota ohjataan tietokoneen avulla RS-232 -väylää käyttäen. Vaatimuksena on myös mahdollisuus ohjata askelmoottorin sijasta servomoottoreita samalla ohjelmalla. Tietokoneen käyttöliittymä suunnitellaan erikseen.

Drivers and Barriers of Collaboration in the Value Chain of Paperboard-Packed Consumer Goods

Value chain collaboration has been a prevailing topic for research, and there is a constantly growing interest in developing collaborative models for improved efficiency in logistics. One area of collaboration is demand information management, which enables improved visibility and decrease of inventories in the value chain. Outsourcing of non-core competencies has changed the nature of collaboration from intra-enterprise to cross-enterprise activity, and this together with increasing competition in the globalizing markets have created a need for methods and tools for collaborative work. The retailer part in the value chain of consumer packaged goods (CPG) has been studied relatively widely, proven models have been defined, and there exist several best practice collaboration cases. The information and communications technology has developed rapidly, offering efficient solutions and applications to exchange information between value chain partners. However, the majority of CPG industry still works with traditional business models and practices. This concerns especially companies operating in the upstream of the CPG value chain. Demand information for consumer packaged goods originates at retailers' counters, based on consumers' buying decisions. As this information does not get transferred along the value chain towards the upstream parties, each player needs to optimize their part, causing safety margins for inventories and speculation in purchasing decisions. The safety margins increase with each player, resulting in a phenomenon known as the bullwhip effect. The further the company is from the original demand information source, the more distorted the information is. This thesis concentrates on the upstream parts of the value chain of consumer packaged goods, and more precisely the packaging value chain. Packaging is becoming a part of the product with informative and interactive features, and therefore is not just a cost item needed to protect the product. The upstream part of the CPG value chain is distinctive, as the product changes after each involved party, and therefore the original demand information from the retailers cannot be utilized as such – even if it were transferred seamlessly. The objective of this thesis is to examine the main drivers for collaboration, and barriers causing the moderate adaptation level of collaborative models. Another objective is to define a collaborative demand information management model and test it in a pilot business situation in order to see if the barriers can be eliminated. The empirical part of this thesis contains three parts, all related to the research objective, but involving different target groups, viewpoints and research approaches. The study shows evidence that the main barriers for collaboration are very similar to the barriers in the lower part of the same value chain; lack of trust, lack of business case and lack of senior management commitment. Eliminating one of them – the lack of business case – is not enough to eliminate the two other barriers, as the operational model in this thesis shows. The uncertainty of the future, fear of losing an independent position in purchasing decision making and lack of commitment remain strong enough barriers to prevent the implementation of the proposed collaborative business model. The study proposes a new way of defining the value chain processes: it divides the contracting and planning process into two processes, one managing the commercial parts and the other managing the quantity and specification related issues. This model can reduce the resistance to collaboration, as the commercial part of the contracting process would remain the same as in the traditional model. The quantity/specification-related issues would be managed by the parties with the best capabilities and resources, as well as access to the original demand information. The parties in between would be involved in the planning process as well, as their impact for the next party upstream is significant. The study also highlights the future challenges for companies operating in the CPG value chain. The markets are becoming global, with toughening competition. Also, the technology development will most likely continue with a speed exceeding the adaptation capabilities of the industry. Value chains are also becoming increasingly dynamic, which means shorter and more agile business relationships, and at the same time the predictability of consumer demand is getting more difficult due to shorter product life cycles and trends. These changes will certainly have an effect on companies' operational models, but it is very difficult to estimate when and how the proven methods will gain wide enough adaptation to become standards.

Epäpuhtauksien optinen laskenta sulpusta

Työn tarkoituksena oli hakea mittausjärjestelmän raja-arvoja optiselle kamerapohjaiselle roskalaskentajärjestelmälle sekä testata roskalaskentajärjestelmän toimivuus käytännössä. Tavoitteena oli tuotteistaa kamerapohjainen roskalaskenta-analyysi palvelutuotteeksi, jota voitaisiin hyödyntää sihtien kuntokartoituksessa ja ongelmanratkaisuvälineenä. Teoriaosa koostui kahdesta kokonaisuudesta: sulpun epäpuhtauksista, roskalaskennan teoriasta ja epäpuhtauksien mittausmenetelmistä sekä markkinoinnista, tuotteistamis- ja lanseerausprosessista palvelutuotteen näkökulmasta. Kokeellisessa osassa selvitettiin kamerapohjaiseen roskalaskentaanalyysiin vaikuttavia tekijöitä: kameran tarkennus, kuvan terävyys, analysoitavan arkin väri, neliömassa ja roskapitoisuus, impregnointi, valonlähde, kuvan muokkaus, tiedostomuoto ja pikselimäärä. Kamerapohjaisen roskalaskenta-analyysin soveltuvuus käytäntöön testattiin tehdasesimerkin avulla. Havaittiin, että kamerapohjaista roskalaskenta-analyysiä voitaisiin käyttää lähes kaikille massatyypeille. Työssä määriteltiin kalibrointimenetelmä kameran tarkentamiseksi arkin tasoon sekä suljinnopeusanalyysi massatyypistä riippuvan suljinnopeuden selvitykseen. Kamerapohjaisessa roskalaskenta-analyysissä määritettiin käytettäväksi arkin neliömassana 60 g/m2, suljinaukkoa F5 ja terävyysasetusta 5. Tulokseksi saatiin, että analysoitavia arkkeja ei tarvitse impregnoida tai jälkikäsitellä. Korrelaatiota Somerville-erotustehokkuuteen ei löytynyt. Esimerkkitehtaasta selvitettiin primääriportaan roskapitoisuudet ja erotustehokkuudet. Tehdasesimerkin tulosten perusteella havaittiin happivaiheen ja D0-vaiheen olleen tehokkaimpia epäpuhtauksien poistajia.

Tuulivoimakäytön verkkoliitynnät ja mittaukset

Tässä työssä tutkitaan muuttuvanopeuksisen tuulivoimakäytön verkkoliityntöjä, verkkomääräyksiä ja mittausmenetelmiä Euroopassa. Yleiset tuulivoimalaitoksen verkkomääräyksiin liittyvät asiat on selitetty standardisarjassa IEC 61000 ja mittauksiin liittyvät säännökset standardissa IEC 61400-21. Työssä selvitetään Euroopan yleiset verkkomääräykset ja vertaillaan niitä keskenään, sekä määritetään tärkeimmät mittaukset. Lisäksi esitellään eräs standardimittauksiin soveltuva mittalaite ja analysoidaan täystehomuokkaimen suorituskykyä tuulivoimapuistossa. Työssä havaittiin, että standardin mukaisten mittausten toteuttaminen ja analysointi on hyvin haastava prosessi. Verkkomääräysten eroavaisuudet aiheuttavat hankaluuksia tuulivoimalan valmistajan ja verkko-operaattorien välillä. Täten myös konvertterivalmistajan täytyy olla selvillä käytössä olevista verkkomääräyksistä ja standardeista.

Overvoltage Mitigation Techniques in Wind Power Generators

Advancements in power electronic semiconductor switching devices have lead to significantly faster switching times. In motor and generator applications, the fast switching times of pulse width modulated (PWM) inverters lead to overvoltages caused by voltage reflections with shorter and shorter cables. These excessive overvoltages may lead to a failure of the electrical machine in a matter of months. In this thesis, the causes behind the overvoltage phenomenon as well as its different mitigation techniques are studied. The most suitable techniques for mitigating the overvoltage phenomenon in wind power generator applications are chosen based on both simulations and actual measurements performed on a prototype. An RC filter at the terminals of the electrical machine and an inverter output filter designed to reduce the rise and fall times of voltage pulses are presented as a solution to the overvoltage problem. The performance and losses of both filter types are analysed.

Simulations of 3D Stripixel Detectors

Large Hadron Collider (LHC) is the main particle accelerator at CERN. LHC is created with main goal to search elementary particles and help science investigate our universe. Radiation in LHC is caused by charged particles circular acceleration, therefore detectors tracing particles in existed severe conditions during the experiments must be radiation tolerant. Moreover, further upgrade of luminosity (up to 1035 cm-2s-1) requires development of particle detector’s structure. This work is dedicated to show the new type 3D stripixel detector with serious structural improvement. The new type of radiation-hard detector has a three-dimensional (3D) array of the p+ and n+ electrodes that penetrate into the detector bulk. The electrons and holes are then collected at oppositely biased electrodes. Proposed 3D stripixel detector demonstrates that full depletion voltage is lower that that for planar detectors. Low depletion voltage is one of the main advantages because only depleted part of the device is active are. Because of small spacing between electrodes, charge collection distances are smaller which results in high speed of the detector’s response. In this work is also briefly discussed dual-column type detectors, meaning consisting both n+ and p+ type columnar electrodes in its structure, and was declared that dual-column detectors show better electric filed distribution then single sided radiation detectors. The dead space or in other words low electric field region in significantly suppressed. Simulations were carried out by using Atlas device simulation software. As a simulation results in this work are represented the electric field distribution under different bias voltages.

Vaahdonestokemikaalin syöttötapahtuman tehostamisen vaikutus märkäosan toimintaan

An improved defoamer dosage procedure and a more efficient dosing point to the approach system were studied in this thesis. Their influence on paper machine wet end operations was investigated. The improved defoamer dosing procedure was examined at UMP-Kymmene Tervasaari PM8. Air content and its controlling methods at the paper machine were studied in the literature survey. Also the influence of dissolved gases and entrained air in the papermaking furnish were introduced. Feeding methods – a TrumpJet chemical mixer and traditional feeding devices – were reviewed. The defoamer’s functioning methods were studied. The influence of the use of defoamers was estimated based on the main selected wet end operations. In the experimental part, defoamer mixing with a traditional feeding method and two improved mixing stages were compared based on the air content profiles in PM8’s approach system. The reference dosage procedure was PM8’s old dosing system. The first dosage procedure in the comparison involved two TrumpJet chemical mixers installed on the bottom wire trays. The second element of comparison involved the improvement brought by a third TrumpJet chemical mixer installed on the top wire tray. This second comparison of the efficient defoamer feeding concept was made at a higher production speed of PM8. The air content control situation was also studied at the higher production speed. In addition the connection between the defoamer and air content was observed and a mill-scale system was studied. The economical benefits of the new dosing procedure were also reviewed. Air content profiles of short circulation were measured in the reference situation and the two comparison points of the study. These air content measurements proved the main gas load is introduced to PM8's paper furnish from the white water tray. Thick stock air content was not essential when the air volume flow was considered. The improved defoamer dosing procedure made lower dosage amounts possible. Compared with the traditional feeding system, the new defoamer feeding concept made only few direct improvements to the wet end operations and the produced paper itself. The lower defoamer need was noticed to have a positive influence on hydrophobic sizing and paper defects. The surfaces of the white water tanks and the operation of pumps were assessed based on the density variations of the suspension. The temperature in the white water silo was stated to have a significant influence on the air content measured in the first centrifugal cleaning stage.

Position sensorless electrically excited synchronous motor drive for industrial use based on direct flux linkage and torque control

Synchronous machines with an AC converter are used mainly in large drives, for example in ship propulsion drives as well as in rolling mill drives in steel industry. These motors are used because of their high efficiency, high overload capacity and good performance in the field weakening area. Present day drives for electrically excited synchronous motors are equipped with position sensors. Most drives for electrically excited synchronous motors will be equipped with position sensors also in future. This kind of drives with good dynamics are mainly used in metal industry. Drives without a position sensor can be used e.g. in ship propulsion and in large pump and blower drives. Nowadays, these drives are equipped with a position sensor, too. The tendency is to avoid a position sensor if possible, since a sensor reduces the reliability of the drive and increases costs (latter is not very significant for large drives). A new control technique for a synchronous motor drive is a combination of the Direct Flux Linkage Control (DFLC) based on a voltage model and a supervising method (e.g. current model). This combination is called Direct Torque Control method (DTC). In the case of the position sensorless drive, the DTC can be implemented by using other supervising methods that keep the stator flux linkage origin centered. In this thesis, a method for the observation of the drift of the real stator flux linkage in the DTC drive is introduced. It is also shown how this method can be used as a supervising method that keeps the stator flux linkage origin centered in the case of the DTC. In the position sensorless case, a synchronous motor can be started up with the DTC control, when a method for the determination of the initial rotor position presented in this thesis is used. The load characteristics of such a drive are not very good at low rotational speeds. Furthermore, continuous operation at a zero speed and at a low rotational speed is not possible, which is partly due to the problems related to the flux linkage estimate. For operation in a low speed area, a stator current control method based on the DFLC modulator (DMCQ is presented. With the DMCC, it is possible to start up and operate a synchronous motor at a zero speed and at low rotational speeds in general. The DMCC is necessary in situations where high torque (e.g. nominal torque) is required at the starting moment, or if the motor runs several seconds at a zero speed or at a low speed range (up to 2 Hz). The behaviour of the described methods is shown with test results. The test results are presented for the direct flux linkage and torque controlled test drive system with a 14.5 kVA, four pole salient pole synchronous motor with a damper winding and electric excitation. The static accuracy of the drive is verified by measuring the torque in a static load operation, and the dynamics of the drive is proven in load transient tests. The performance of the drive concept presented in this work is sufficient e.g. for ship propulsion and for large pump drives. Furthermore, the developed methods are almost independent of the machine parameters.

Hitsatun kerrossihtilevyrakenteen soveltuvuus sellutehtaan laitteiden suodatinpinnaksi

Tässä diplomityössä tutkittiin hitsaamalla valmistettavan kerrossihtilevyn soveltuvuutta eri sellutehtaan laitteisiin mekaanisen kuormituskokeen, korroosiokokeen ja syrjäytyskokeiden avulla. Tutkimusympäristönä käytettiin puukuitupesuria, sillä kerrossihtilevyrakenteen todennäköisimpiä käyttökohteita ovat erilaiset massan pesuun tarkoitetut laitteet. Mekaanisen kuormituksen kokeessa tarkasteltiin kerrossihtilevyn staattista ja dynaamista kuormituksen kestoa painevaihteluiden avulla pesurin koelokerossa ja verrattiin sitä porattuun reikälevyyn. Kokeessa käytetyn kerrossihtilevyversion todettiin olevan huomattavasti porattua saman paksuista reikälevyä heikompi dynaamisen kuormituksen alaisena. Syrjäytyskokeilla määritettiin syrjäytysnopeus erilaisilla reiänhalkaisijoilla ja –jaoilla sekä tutkittiin väriaineen avulla sokeiden tukikannasten vaikutusta syrjäytyspesun homogeenisuuteen levyn pinnassa. Syrjäytysnopeuden todettiin heikentyvän vapaan reikäpinta-alan pienentyessä. Väriaineellisissa kokeissa ei havaittu tukikannasten merkittävästi alentavan syrjäytysnopeutta. Korroosiokokeilla tutkittiin ja vertailtiin laser- ja vastuspistehitsien korroosionkestokykyä kloridipitoisissa olosuhteissa lämpötilan säätelyn mahdollistavan olosuhdekaapin avulla. Laserhitsauksessa parametrien ei havaittu vaikuttavan merkittävästi hitsin herkistymislämpötilaan. Vastuspistehitsaamalla on mahdollista saavuttaa laserhitsien korroosionkesto.

Welding of Sheet metal using Modified short arc MIG/MAG welding process

In this research work, the results of an investigation dealing with welding of sheet metals with diverse air gap using FastROOT modified short arc welding method and short circuit MAG welding processes have been presented. Welding runs were made under different conditions and, during each run, the different process parameters were continuously monitored. It was found that maximum welding speed and less HAZ are reached under specific welding conditions with FastROOT method with the emphasis on arc stability. Welding results show that modified short arc exhibits a higher electrode melting coefficient and with virtually spatter free droplet transition. By adjusting the short circuit duration the penetration can be controlled with only a small change in electrode deposition. Furthermore, by mixing pulsed MIG welding with modified arc welding the working envelope of the process is greatly extended allowing thicker material sections to be welded with improved weld bead aesthetics. FastROOT is a modified short arc welding process using mechanized or automated welding process based on dip transfer welding, characterized by controlled material deposition during the short circuit of the wire electrode to the workpiece.

The Role of Network Competence in Internationalization of SMEs

Network competence is the ability of firms to manage their network of business relationships and to deal effectively with interactions in these relationships. The relationship between level of business relationship abilities of firms and their internationalization has been researched before, and found to be positive. However, what network competence specifically offers is an established scale with which to perform this examination quantitatively. This master’s thesis examined the role which this network competence plays in the internationalization of firms, more specifically in Finnish small and medium sized enterprises (SMEs). The theoretical part of the thesis consisted of examination into the nature of internationalization of SMEs, their business relationships, network competence and related concepts. The empirical part was conducted statistically with quantitative methods on data gathered from Finnish SMEs through a web-survey during 2008. Network competence was found to result in better internationalization among the examined Finnish SMEs with both subjective and objective performance measures, and firms with higher levels of network competence were found to be more likely to become international. On the other hand, speed of internationalization could not be linked to better network competence, and no clear industry-specific differences were found. The results show that by developing their network competence, Finnish SMEs can increase their chances of success and performance in their internationalization process

Hybrid LC Filter for Power Electronic Drives: Theory and Implementation

Power electronic converter drives use, for the sake of high efficiency, pulse-width modulation that results in sequences of high-voltage high-frequency steep-edged pulses. Such a signal contains a set of high harmonics not required for control purposes. Harmonics cause reflections in the cable between the motor and the inverter leading to faster winding insulation ageing. Bearing failures and problems with electromagnetic compatibility may also result. Electrical du/dt filters provide an effective solution to problems caused by pulse-width modulation, thereby increasing the performance and service life of the electrical machines. It is shown that RLC filters effectively decrease the reflection phenomena in the cable. Improved (simple, but effective) solutions are found for both differential- and common-mode signals; these solutions use a galvanic connection between the RLC filter star point and the converter DC link. Foil chokes and film capacitors are among the most widely used components in high-power applications. In actual applications they can be placed in different parts of the cabinet. This fact complicates the arrangement of the cabinet and decreases the reliability of the system. In addition, the inductances of connection wires may prevent filtration at high frequencies. This thesis introduces a new hybrid LC filter that uses a natural capacitance between the turns of the foil choke based on integration of an auxiliary layer into it. The main idea of the hybrid LC filter results from the fact that both the foil choke and the film capacitors have the same roll structure. Moreover, the capacitance between the turns (“intra capacitance”) of the foil inductors is the reason for the deterioration of their properties at high frequencies. It is shown that the proposed filter has a natural cancellation of the intra capacitance. A hybrid LC filter may contain two or more foil layers isolated from each other and coiled on a core. The core material can be iron or even air as in the filter considered in this work. One of the foils, called the main foil, can be placed between the inverter and the motor cable. Other ones, called auxiliary foils, may be connected in star to create differential-mode noise paths, and then coupled to the DC link midpoint to guarantee a traveling path, especially for the common-mode currents. This way, there is a remarkable capacitance between the main foil and the auxiliary foil. Investigations showed that such a system can be described by a simple equivalent LC filter in a wide range of frequencies. Because of its simple hybrid construction, the proposed LC filter can be a cost-effective and competitive solution for modern power drives. In the thesis, the application field of the proposed filter is considered and determined. The basics of hybrid LC filter design are developed further. High-frequency behaviour of the proposed filter is analysed by simulations. Finally, the thesis presents experimental data proving that the hybrid LC filter can be used for du/dt of PWM pulses and reduction of common-mode currents.

Study of a vapor-compression air-conditioning system for jetliners

Most modern passenger aeroplanes use air cycle cooling. A high-speed air cycle is a reliable and light option, but not very efficient. This thesis presents research work done to design a novel vapour cooling cycle for aeroplanes. Due to advancements in high-speed permanent magnet motors, the vapour cycle is seen as a competitive option for the air cycle in aeroplanes. The aerospace industry places tighter demands on the weight, reliability and environmental effects of the machinery than those met by conventional chillers, and thus modifications to conventional design are needed. The thesis is divided into four parts: the initial screening of the working fluid, 1-D design and performance values of the compressor, 1-D off-design value predictions of the compressor and the 3-D design of the compressor. The R245fa was selected as the working fluid based the study. The off-design range of the compressor was predicted to be wide and suitable for the application. The air-conditioning system developed is considerably smaller than previous designs using centrifugal compressors.